[why]
Read link setting inside mode validation is not always the final downlink setting.
It is found true in Synaptics branch device.
At bootup, the preferred mode being set right after 1080p is set. It occurred
before graphic load. That modeset switch in a short period of time makes
the branch device switch back and forth from lower and higher link rate,
observed at Synaptics branch device.
DP2 RTK hub on the other hand, sticks to highest available downlink rate after bootup.
Existing check of runtime downlink setting in mode validation shows asynchronous at
branch device link switch, i.e., downlink switch to higher link rate not yet complete
when the mode validation tries to probe the downlink setting. That makes mode validation
checking downlink setting making wrong decision by pruning modes that should pass the
validation after the downlink setting switch is complete.
[how]
If Synaptics is found at the last branch, skip checking downlink setting
at mode validation.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Previously, when calculating dto phase, we would incorrectly fail when phase
<=0 without additionally checking for the integer value. This meant that
calculations would incorrectly fail when the desired pixel clock was an exact
multiple of the reference clock.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Clay King <clayking@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bounding box values can be stored in multiple locations. (e.g. PMFW, VBIOS, DMUB).
The source and interpretation of these values can vary with DCN revision
so there should be a component that can gather these values and translate
them accordingly
[How]
Have component start with the statically defined values as a base.
Then update them as needed with DCN-specific logic
Guard this component with FPU flags since values need to be in float point.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Custom brightness curve works by walking through all data points one
by one. When the brightness value is at either extreme this is a lot
of data points to walk. This is especially noticeable when moving a
brightness slider around how it can lag.
[How]
Bisect the data points to find the closest for interpolation.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
-Pipe splitting allows for clocks to be reduced, but when using TMDS 420,
reduced clocks lead to missed clocks cycles on clock resyncing
[How]
-Impose a minimum clock when using TMDS 420
Reviewed-by: Chris Park <chris.park@amd.com>
Signed-off-by: Relja Vojvodic <rvojvodi@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The patch uses power state of VCN instances for requesting video
profile.
In idle worker of a vcn instance, when there is no outstanding
submisssion or fence, the instance is put to power gated state. When
all instances are powered off that means video profile is no longer
required. A request is made to turn off video profile.
A job submission starts with begin_use of ring, and at that time
vcn instance state is changed to power on. Subsequently a check is
made for active video profile, and if not active, a request is made.
Fixes: 3b669df92c ("drm/amdgpu/vcn: adjust workload profile handling")
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Sathishkumar S <sathishkumar.sundararaju@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v1:
1. Unified amdgpu ip block name print with format
"{ip_type}_v{major}_{minor}_{rev}"
2. Avoid IP block name conflicts for SMU/PSP ip block
v2:
Update IP block print format to keep legacy IP block name (Alex)
"{ip_type}_v{major}_{minor}_{rev} ({funcs->name})"
Signed-off-by: Yang Wang <kevinyang.wang@amd.com>
Reviewed-by: Asad Kamal <asad.kamal@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Using the previous firmware could lead to problems with
PROTECTED_FENCE_SIGNAL commands, specifically causing register
conflicts between MCU_DBG0 and MCU_DBG1.
The updated firmware versions ensure proper alignment
and unification of the SDMA_SUBOP_PROTECTED_FENCE_SIGNAL value with SDMA 7.x,
resolving these hardware coordination issues
Fixes: e8cca30d8b ("drm/amdgpu/sdma6: add ucode version checks for userq support")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Notify pmfw when bad page threshold is exceeded, no matter the module
parameter 'bad_page_threshold' is set or not.
Signed-off-by: Xiang Liu <xiang.liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For multiple VCN instances case we get multiple lines of the same
message like below:
amdgpu 0000:43:00.0: amdgpu: Found VCN firmware Version ENC: 1.24 DEC: 9 VEP: 0 Revision: 11
amdgpu 0000:43:00.0: amdgpu: Found VCN firmware Version ENC: 1.24 DEC: 9 VEP: 0 Revision: 11
By adding instance number to the log message for multiple VCN instances,
each line will clearly indicate which VCN instance it refers to.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: David (Ming Qiang) Wu <David.Wu3@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use max() to reduce the code and improve readability.
No functional changes.
Signed-off-by: Qianfeng Rong <rongqianfeng@vivo.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix a kernel-doc warning by documenting the num_rmcm_3dluts member of struct mpc_color_caps.
v2: improve comment (Melissa)
Signed-off-by: Kavithesh A.S <kavitheshnitt@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the doorbell is invalid, be sure to set the r to an error
state so the function returns an error.
Reviewed-by: David (Ming Qiang) Wu <David.Wu3@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The minimum firmware versions required for user queue functionality
have been increased to address an issue where the queue privilege
state was lost during queue connect operations.
The problem occurred because the privilege state was being restored
to its initial value at the beginning of the function, overwriting
the state that was properly set during the queue connect case.
This commit updates the minimum version requirements:
- ME firmware from 2390 to 2420
- PFP firmware from 2530 to 2580
- MEC firmware from 2600 to 2650
- MES firmware remains at 120
These updated firmware versions contain the necessary fixes to
properly maintain queue privilege state throughout connect operations.
Fixes: 61ca97e959 ("drm/amdgpu: Add fw minimum version check for usermode queue")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to cancel any outstanding work at both suspend
and driver teardown. Move the cancel to hw_fini which
gets called in both cases.
Reviewed-by: David (Ming Qiang) Wu <David.Wu3@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The requirement from driver side is to have an API that can do the
tlb invalidation on dedicate pasid since driver don't know the vmid
and process mapping.
Make the API generic to support different tlb invalidation related
request. Driver can specify pasid, vmid, hub_id and vm address range
need to be invalidated.
With this API the old INV_GART in MISC Op can be deprecated.
Signed-off-by: Shaoyun Liu <shaoyun.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix a UBSAN shift-out-of-bounds warning in amdgpu_debugfs_jpeg_sched_mask_set
when the shift exponent reaches or exceeds 32 bits. The issue occurred because
a 32-bit integer '1' was being shifted by up to 32 bits, which is undefined
behavior.
Replace '1' with '1ULL' to ensure 64-bit arithmetic, matching the u64 type of
'val' and preventing the shift overflow. This is consistent with the existing
mask calculation that already uses 1ULL.
The error manifested as:
UBSAN: shift-out-of-bounds in drivers/gpu/drm/amd/amdgpu/amdgpu_jpeg.c:373:17
shift exponent 32 is too large for 32-bit type 'int'
v2: remove debug log
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DC Release v3.2.347
* Firmware releases for multiple asics
* CodeQL fixes
* Fix for double cursor with 180 degree rotation on large resolutions
* Misc bug fixes for DSC, PSR/Replay, DPIA etc.
Signed-off-by: Nicholas Carbones <ncarbone@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It should use vm flags instead of pte flags
to specify bo vm attributes.
This reverts commit 1263ceea2a1327014d9de2858a122f3c27dfa4dd.
Reapply this patch with the proper fixes tag.
Fixes: 6716a823d1 ("drm/amdgpu: rework how PTE flags are generated v3")
Signed-off-by: Jack Xiao <Jack.Xiao@amd.com>
Reviewed-by: Likun Gao <Likun.Gao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit b08425fa77.
Revert this to align with 6.17 because the fixes tag
was wrong on this commit.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
The sink max slice width limitation should be considered for DSC, but
was removed in "refactor DSC cap calculations".
This patch adds it back and takes the valid minimum between the sink and
source.
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For the HW cursor, its current position in the pipe_ctx->stream struct is
not affected by the 180 rotation, i. e. the top left corner is still at
0,0. However, the DPP & HUBP set_cursor_position functions require rotated
position.
The current approach is hard-coded for ODM 2:1, thus it's failing for
ODM 4:1, resulting in a double cursor.
[How]
Instead of calculating the new cursor position relatively to the
viewports, we calculate it using a viewavable clip_rect of each plane.
The clip_rects are first offset and scaled to the same space as the
src_rect, i. e. Stream space -> Plane space.
In case of a pipe split, which divides the plane into 2 or more viewports,
the clip_rect is the union of all the viewports of the given plane.
With the assumption that the viewports in HUBP's set_cursor_position are
in the Plane space as well, it should produce a correct cursor position
for any number of pipe splits.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement ring reset for VPE. Similar to VCN and JPEG,
just powergate the the IP to reset it.
v2: Properly set per queue reset flag
Reviewed-by: Jesse Zhang <jesse.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We already call this in the hw_fini() methods for all
VCN instances, so no need to call it again in
amdgpu_vcn_suspend().
Tested-by: David (Ming Qiang) Wu <David.Wu3@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When KFD asks CP to preempt queues, other than preempt CP queues, CP
also requests SDMA to preempt SDMA queues with UNMAP_LATENCY timeout.
Currently queue_preemption_timeout_ms is 9000 ms by default but can be
configured via module parameter. KFD_UNMAP_LATENCY_MS is hard coded as
4000 ms though. This patch ties KFD_UNMAP_LATENCY_MS to
queue_preemption_timeout_ms so in a slow system such as emulator, both
CP and SDMA slowness are taken into account.
Signed-off-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Update the conditions for setting the SMU vcn reset caps in the SMU v13.0.6 PPT
initialization function. Specifically:
- Add support for VCN reset capability for firmware versions 0x00558200 and
above when the program version is 0.
- Add support for VCN reset capability for firmware versions 0x05551800 and
above when the program version is 5.
v2: correct the smu mp1 version for program 5 (Lijo)
Suggested-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Jesse Zhang <Jesse.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Yang Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When it only allocates vram without va, which is 0, and a
SVM range allocated stays in this range, the vram allocation
returns failure. It should be skipped for this case from
SVM usage check.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The addition of a WARN_ON() check in order to return early in the
kq_initialize function retroactively causes the default case in the
following switch statement to never be executed, preventing dev_err
from logging device errors in the kernel. Both logs are now checked
in the default case.
Signed-off-by: Sunday Clement <Sunday.Clement@amd.com>
Reviewed-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
