There are devices (such as Murata IRS-D200 PIR proximity sensor) that
check the data signal with a running period. I.e. for a specified time,
they count the number of conditions that have occurred, and then signal
if that is more than a specified amount.
`IIO_EV_INFO_PERIOD` resets when the condition no longer is true and is
therefore not suitable for these devices. Add a new `iio_event_info`
`IIO_EV_INFO_RUNNING_PERIOD` that can be used as a running period. Also
add a new `IIO_EV_INFO_RUNNING_COUNT` that can be used to specify the
number of conditions that must occur during this running period.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/ee4a801ae9b9c4716c7bd23d8f79f232351df8bd.1689753076.git.waqar.hameed@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Define and init voltage configuration bits. Those bits are inited in
vendor boot code (bl2, bl33) already so do it in the driver to not depend
on other code.
Introduced bits:
REG11[0] - selects Vref. 0 - calibration voltage, 1 - VDDA. txlx and later
SoCs support VDDA or calibration voltage as Vref, but others
support only calibration voltage. For newer platforms vendor
uses VDDA as default.
REG11[1] - reserved bit. g12a and later SoCs must write 1, others SoCs
write 0.
REG11[5] - Vref voltage. 0 - 0.9v, 1 - 1.8v. g12a and later SoCs must
write 0, others SoCs write 1.
REG11[6] - selects common-mode voltage, 0: from AVDD, 1: from Vref.
g12a and later SoCs must write 0, others SoCs write 1.
Signed-off-by: George Stark <gnstark@sberdevices.ru>
Link: https://lore.kernel.org/r/20230715110654.6035-4-gnstark@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In `iio_trigger_detach_poll_func()` the return value from
`trig->ops->set_trigger_state(trig, false)` is checked with `if (ret)`.
However, in `iio_trigger_attach_poll_func()` it is checked with
`if (ret < 0)`. Resolve this mismatch by only checking for `if (ret)` in
both places.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Link: https://lore.kernel.org/r/pndv8eojdey.fsf@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Enable buffered reading of samples from the LMP92064 ADC.
The main benefit of this change is being able to read out current and
voltage measurements in a single transfer, allowing instantaneous power
measurements.
Reads into the buffer can be triggered by any software triggers, e.g.
the iio-trig-hrtimer:
$ mkdir /sys/kernel/config/iio/triggers/hrtimer/my-trigger
$ cat /sys/bus/iio/devices/iio\:device3/name
lmp92064
$ iio_readdev -t my-trigger -b 16 iio:device3 | hexdump
WARNING: High-speed mode not enabled
0000000 0000 0176 0101 0001 5507 abd5 7645 1768
0000010 0000 016d 0101 0001 ee1e ac6b 7645 1768
...
Signed-off-by: Leonard Göhrs <l.goehrs@pengutronix.de>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230707063635.1496437-1-l.goehrs@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When processing data read the full fifo data in 1 time. If there
are several samples in the FIFO, it means we are experiencing
system delay. In this case, it is better to read all data with 1
bus access than to add additional latency by doing several ones.
This requires to use a bigger buffer depending on chip FIFO size
and do an additional local data copy before sending. But the cost
is minimal and behavior is still better like this under system
heavy load.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230623082924.283967-1-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The General Purpose ADC (GPADC) can convert the external signal into
a certain proportion of digital value, to realize the measurement of
analog signal, which can be applied to power detection and key detection.
Theoretically, this ADC can support up to 16 channels. All SoCs below
contain this GPADC IP. The only difference between them is the number
of available channels:
T113 - 1 channel
D1 - 2 channels
R329 - 4 channels
T507 - 4 channels
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Maksim Kiselev <bigunclemax@gmail.com>
Link: https://lore.kernel.org/r/20230619154252.3951913-3-bigunclemax@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add the proximity multi pulse (PS_MPS) as oversampling_ratio.
Instead of one single pulse per every defined time frame, one can
program2, 4, or even 8 pulses. This leads to a longer IRED on-time
for each proximity measurement value, which also results in a higher
detection range.
Add read/write attribute for proximity oversampling-ratio and read
attribute for available oversampling-ratio.
This is supported for vcnl4040 and vcnl4200.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-8-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add read/write attribute for proximity and illuminance period. The
period is set in the interrupt persistence flags(PS_PERS and ALS_PERS).
An interrupt will not be asserted if the raw value is not over (or lower)
than the threshold for the set continued amount of measurements.
The time in seconds is calculated by the number of continued refreshes
multiplied with the integration time.
It will always pick the next lower possible value. The period changes,
if the integration time is changed.
Signed-off-by: Astrid Rost <astrid.rost@axis.com>
Link: https://lore.kernel.org/r/20230613135025.2596641-7-astrid.rost@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.
The answer is "No. No we cannot".
I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street. And at the yearly
maintainer summit, we will all sing the alphabet song together.
I doubt I will keep doing this. At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.
Repeats: 80e62bc848 ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull dma-mapping fixes from Christoph Hellwig:
- swiotlb area sizing fixes (Petr Tesarik)
* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: reduce the number of areas to match actual memory pool size
swiotlb: always set the number of areas before allocating the pool
Pull irq update from Borislav Petkov:
- Optimize IRQ domain's name assignment
* tag 'irq_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdomain: Use return value of strreplace()
Pull x86 fpu fix from Borislav Petkov:
- Do FPU AP initialization on Xen PV too which got missed by the recent
boot reordering work
* tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/xen: Fix secondary processors' FPU initialization
