- Start making audio and GPU clks work on Marvell MMP2/MMP3 SoCs
- Add support for X1830 and X1000 Ingenic SoC clk controllers
- Add support for Qualcomm's MSM8939 Generic Clock Controller
- Add some GPU, NPU, and UFS clks to Qualcomm SM8150 driver
- Enable supply regulators for GPU gdscs on Qualcomm SoCs
- Add support for Si5342, Si5344 and Si5345 chips
* clk-mmp:
clk: mmp2: Add audio clock controller driver
dt-bindings: clock: Add Marvell MMP Audio Clock Controller binding
clk: mmp2: Add support for power islands
dt-bindings: marvell,mmp2: Add ids for the power domains
dt-bindings: clock: Make marvell,mmp2-clock a power controller
clk: mmp2: Add the audio clock
clk: mmp2: Add the I2S clocks
clk: mmp2: Rename mmp2_pll_init() to mmp2_main_clk_init()
clk: mmp2: Move thermal register defines up a bit
dt-bindings: marvell,mmp2: Add clock id for the Audio clock
dt-bindings: marvell,mmp2: Add clock id for the I2S clocks
clk: mmp: frac: Allow setting bits other than the numerator/denominator
clk: mmp: frac: Do not lose last 4 digits of precision
* clk-intel:
clk: intel: remove redundant initialization of variable rate64
clk: intel: Add CGU clock driver for a new SoC
dt-bindings: clk: intel: Add bindings document & header file for CGU
* clk-ingenic:
clk: ingenic: Mark ingenic_tcu_of_match as __maybe_unused
clk: X1000: Add FIXDIV for SSI clock of X1000.
dt-bindings: clock: Add and reorder ABI for X1000.
clk: Ingenic: Add CGU driver for X1830.
dt-bindings: clock: Add X1830 clock bindings.
clk: Ingenic: Adjust cgu code to make it compatible with X1830.
clk: Ingenic: Remove unnecessary spinlock when reading registers.
* clk-qcom:
clk: qcom: Add missing msm8998 ufs_unipro_core_clk_src
dt-bindings: clock: Add YAML schemas for QCOM A53 PLL
clk: qcom: gcc-msm8939: Add MSM8939 Generic Clock Controller
clk: qcom: gcc: Add support for Secure control source clock
dt-bindings: clock: Add gcc_sec_ctrl_clk_src clock ID
clk: qcom: gcc: Add support for a new frequency for SC7180
clk: qcom: Add DT bindings for MSM8939 GCC
clk: qcom: gcc: Add missing UFS clocks for SM8150
clk: qcom: gcc: Add GPU and NPU clocks for SM8150
clk: qcom: mmcc-msm8996: Properly describe GPU_GX gdsc
clk: qcom: gdsc: Handle GDSC regulator supplies
clk: qcom: msm8916: Fix the address location of pll->config_reg
* clk-silabs:
clk: clk-si5341: Add support for the Si5345 series
- Allow the COMMON_CLK config to be selectable
* clk-selectable:
clk: Move HAVE_CLK config out of architecture layer
MIPS: Loongson64: Drop asm/clock.h include
ARM: mmp: Remove legacy clk code
clk: Allow the common clk framework to be selectable
mmc: meson-mx-sdio: Depend on OF_ADDRESS and not just OF
MIPS: Remove redundant CLKDEV_LOOKUP selects
h8300: Remove redundant CLKDEV_LOOKUP selects
arm64: tegra: Remove redundant CLKDEV_LOOKUP selects
ARM: Remove redundant CLKDEV_LOOKUP selects
ARM: Remove redundant COMMON_CLK selects
* clk-amlogic:
clk: meson: meson8b: Don't rely on u-boot to init all GP_PLL registers
clk: meson: meson8b: Make the CCF use the glitch-free VPU mux
clk: meson: meson8b: Fix the vclk_div{1, 2, 4, 6, 12}_en gate bits
clk: meson: meson8b: Fix the polarity of the RESET_N lines
clk: meson: meson8b: Fix the first parent of vid_pll_in_sel
clk: meson: g12a: Prepare the GPU clock tree to change at runtime
clk: meson: gxbb: Prepare the GPU clock tree to change at runtime
clk: meson: meson8b: make the hdmi_sys clock tree mutable
clk: meson8b: export the HDMI system clock
* clk-renesas:
dt-bindings: clock: renesas: mstp: Convert to json-schema
dt-bindings: clock: renesas: div6: Convert to json-schema
clk: renesas: cpg-mssr: Fix STBCR suspend/resume handling
clk: renesas: rcar-gen2: Remove superfluous CLK_RENESAS_DIV6 selects
clk: renesas: cpg-mssr: Add R8A7742 support
dt-bindings: clock: renesas: cpg-mssr: Document r8a7742 binding
clk: renesas: Add r8a7742 CPG Core Clock Definitions
dt-bindings: power: rcar-sysc: Add r8a7742 power domain index macros
MAINTAINERS: Add DT Bindings for Renesas Clock Generators
clk: renesas: r9a06g032: Fix some typo in comments
dt-bindings: clock: renesas: rcar-usb2-clock-sel: Add r8a77961 support
* clk-samsung:
clk: samsung: exynos5433: Add IGNORE_UNUSED flag to sclk_i2s1
ARM/SAMSUNG EXYNOS ARM ARCHITECTURES: Use fallthrough;
clk: samsung: Fix CLK_SMMU_FIMCL3 clock name on Exynos542x
clk: samsung: Mark top ISP and CAM clocks on Exynos542x as critical
* clk-allwinner:
clk: sunxi: Fix incorrect usage of round_down()
1.The SSI clock of X1000 not like JZ4770 and JZ4780, they are not
directly derived from the output of SSIPLL, but from the clock
obtained by dividing the frequency by 2. "X1000_CLK_SSIPLL_DIV2"
is added for this purpose, it must between "X1000_CLK_SSIPLL"
and "X1000_CLK_SSIMUX", otherwise an error will occurs when
initializing the clock. These ABIs are only used for X1000, and
I'm sure that no other devicetree out there is using these ABIs,
so we should be able to reorder them.
2.Clocks of LCD, OTG, EMC, EFUSE, OST, TCU are also added.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lkml.kernel.org/r/20200528031549.13846-7-zhouyanjie@wanyeetech.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
On MMP2 the audio and GPU blocks are on separate power islands. On MMP3
the camera block's power is also controlled separately.
Add the numbers that we could use to refer to the power domains for
respective power islands from the device tree.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lkml.kernel.org/r/20200519224151.2074597-11-lkundrak@v3.sk
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Inspried from
commit e8688fe8df ("clk: imx8mn: Define gates for pll1/2 fixed dividers")
On imx8mp there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate. Only one of these gates (the one "dividing" by
one) is currently defined and it's incorrectly set as the parent of all
the fixed-factor dividers.
Add the other 8 gates to the clock tree between sys_pll1/2_bypass and
the fixed dividers.
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The EMC clock needs to carefully coordinate with the EMC controller
programming to make sure external memory can be properly clocked. Do so
by hooking up the EMC clock with an EMC provider that will specify which
rates are supported by the EMC and provide a callback to use for setting
the clock rate at the EMC.
Based on work by Peter De Schrijver <pdeschrijver@nvidia.com>.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Export functions to allow accessing the CAR register required by EMC
clock scaling. These functions will be used to access the CAR register
as part of the scaling sequence.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Introduce the low jitter path of PLLP and PLLMB which can be used as EMC
clock source.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra210 uses PLLD out internally for CSI TPG. This patch adds a clock
ID for this CSI TPG clock from PLLD.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
ARM clk could only source from divcore or hsrun_divcore.
Follow what we already used on i.MX7D and i.MX8M SoCs, use
imx_clk_hw_cpu API. When ARM core is running normaly,
whether divcore or hwrun_divcore will finally source
from SPLL_PFD0. However SPLL_PFD0 is marked with CLK_SET_GATE,
so we need to disable SPLL_PFD0, when configure the rate.
So add CORE and HSRUN_CORE virtual clk to make it easy to
configure the clk using imx_clk_hw_cpu API.
Since CORE and HSRUN_CORE already marked with CLK_IS_CRITICAL, no
need to set ARM as CLK_IS_CRITICAL. And when set the rate of ARM clk,
prograting it the parent with CLK_SET_RATE_PARENT will finally set
the SPLL_PFD0 clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull locking fixes from Thomas Gleixner:
"Three small fixes/updates for the locking core code:
- Plug a task struct reference leak in the percpu rswem
implementation.
- Document the refcount interaction with PID_MAX_LIMIT
- Improve the 'invalid wait context' data dump in lockdep so it
contains all information which is required to decode the problem"
* tag 'locking-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/lockdep: Improve 'invalid wait context' splat
locking/refcount: Document interaction with PID_MAX_LIMIT
locking/percpu-rwsem: Fix a task_struct refcount
Pull more Kbuild updates from Masahiro Yamada:
- raise minimum supported binutils version to 2.23
- remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports
- move remaining CONFIG_AS_* tests to Kconfig from Makefile
- enable -Wtautological-compare warnings to catch more issues
- do not support GCC plugins for GCC <= 4.7
- fix various breakages of 'make xconfig'
- include the linker version used for linking the kernel into
LINUX_COMPILER, which is used for the banner, and also exposed to
/proc/version
- link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y, which
allows us to remove the lib-ksyms.o workaround, and to solve the last
known issue of the LLVM linker
- add dummy tools in scripts/dummy-tools/ to enable all compiler tests
in Kconfig, which will be useful for distro maintainers
- support the single switch, LLVM=1 to use Clang and all LLVM utilities
instead of GCC and Binutils.
- support LLVM_IAS=1 to enable the integrated assembler, which is still
experimental
* tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (36 commits)
kbuild: fix comment about missing include guard detection
kbuild: support LLVM=1 to switch the default tools to Clang/LLVM
kbuild: replace AS=clang with LLVM_IAS=1
kbuild: add dummy toolchains to enable all cc-option etc. in Kconfig
kbuild: link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y
MIPS: fw: arc: add __weak to prom_meminit and prom_free_prom_memory
kbuild: remove -I$(srctree)/tools/include from scripts/Makefile
kbuild: do not pass $(KBUILD_CFLAGS) to scripts/mkcompile_h
Documentation/llvm: fix the name of llvm-size
kbuild: mkcompile_h: Include $LD version in /proc/version
kconfig: qconf: Fix a few alignment issues
kconfig: qconf: remove some old bogus TODOs
kconfig: qconf: fix support for the split view mode
kconfig: qconf: fix the content of the main widget
kconfig: qconf: Change title for the item window
kconfig: qconf: clean deprecated warnings
gcc-plugins: drop support for GCC <= 4.7
kbuild: Enable -Wtautological-compare
x86: update AS_* macros to binutils >=2.23, supporting ADX and AVX2
crypto: x86 - clean up poly1305-x86_64-cryptogams.S by 'make clean'
...
Merge yet more updates from Andrew Morton:
- Almost all of the rest of MM (memcg, slab-generic, slab, pagealloc,
gup, hugetlb, pagemap, memremap)
- Various other things (hfs, ocfs2, kmod, misc, seqfile)
* akpm: (34 commits)
ipc/util.c: sysvipc_find_ipc() should increase position index
kernel/gcov/fs.c: gcov_seq_next() should increase position index
fs/seq_file.c: seq_read(): add info message about buggy .next functions
drivers/dma/tegra20-apb-dma.c: fix platform_get_irq.cocci warnings
change email address for Pali Rohár
selftests: kmod: test disabling module autoloading
selftests: kmod: fix handling test numbers above 9
docs: admin-guide: document the kernel.modprobe sysctl
fs/filesystems.c: downgrade user-reachable WARN_ONCE() to pr_warn_once()
kmod: make request_module() return an error when autoloading is disabled
mm/memremap: set caching mode for PCI P2PDMA memory to WC
mm/memory_hotplug: add pgprot_t to mhp_params
powerpc/mm: thread pgprot_t through create_section_mapping()
x86/mm: introduce __set_memory_prot()
x86/mm: thread pgprot_t through init_memory_mapping()
mm/memory_hotplug: rename mhp_restrictions to mhp_params
mm/memory_hotplug: drop the flags field from struct mhp_restrictions
mm/special: create generic fallbacks for pte_special() and pte_mkspecial()
mm/vma: introduce VM_ACCESS_FLAGS
mm/vma: define a default value for VM_DATA_DEFAULT_FLAGS
...
Pull more xen updates from Juergen Gross:
- two cleanups
- fix a boot regression introduced in this merge window
- fix wrong use of memory allocation flags
* tag 'for-linus-5.7-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
x86/xen: fix booting 32-bit pv guest
x86/xen: make xen_pvmmu_arch_setup() static
xen/blkfront: fix memory allocation flags in blkfront_setup_indirect()
xen: Use evtchn_type_t as a type for event channels
devm_memremap_pages() is currently used by the PCI P2PDMA code to create
struct page mappings for IO memory. At present, these mappings are
created with PAGE_KERNEL which implies setting the PAT bits to be WB.
However, on x86, an mtrr register will typically override this and force
the cache type to be UC-. In the case firmware doesn't set this
register it is effectively WB and will typically result in a machine
check exception when it's accessed.
Other arches are not currently likely to function correctly seeing they
don't have any MTRR registers to fall back on.
To solve this, provide a way to specify the pgprot value explicitly to
arch_add_memory().
Of the arches that support MEMORY_HOTPLUG: x86_64, and arm64 need a
simple change to pass the pgprot_t down to their respective functions
which set up the page tables. For x86_32, set the page tables
explicitly using _set_memory_prot() (seeing they are already mapped).
For ia64, s390 and sh, reject anything but PAGE_KERNEL settings -- this
should be fine, for now, seeing these architectures don't support
ZONE_DEVICE.
A check in __add_pages() is also added to ensure the pgprot parameter
was set for all arches.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Eric Badger <ebadger@gigaio.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Link: http://lkml.kernel.org/r/20200306170846.9333-7-logang@deltatee.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "Allow setting caching mode in arch_add_memory() for
P2PDMA", v4.
Currently, the page tables created using memremap_pages() are always
created with the PAGE_KERNEL cacheing mode. However, the P2PDMA code is
creating pages for PCI BAR memory which should never be accessed through
the cache and instead use either WC or UC. This still works in most
cases, on x86, because the MTRR registers typically override the caching
settings in the page tables for all of the IO memory to be UC-.
However, this tends not to work so well on other arches or some rare x86
machines that have firmware which does not setup the MTRR registers in
this way.
Instead of this, this series proposes a change to arch_add_memory() to
take the pgprot required by the mapping which allows us to explicitly
set pagetable entries for P2PDMA memory to UC.
This changes is pretty routine for most of the arches: x86_64, arm64 and
powerpc simply need to thread the pgprot through to where the page
tables are setup. x86_32 unfortunately sets up the page tables at boot
so must use _set_memory_prot() to change their caching mode. ia64, s390
and sh don't appear to have an easy way to change the page tables so,
for now at least, we just return -EINVAL on such mappings and thus they
will not support P2PDMA memory until the work for this is done. This
should be fine as they don't yet support ZONE_DEVICE.
This patch (of 7):
This variable is not used anywhere and should therefore be removed from
the structure.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Eric Badger <ebadger@gigaio.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Link: http://lkml.kernel.org/r/20200306170846.9333-2-logang@deltatee.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 944d9fec8d ("hugetlb: add support for gigantic page allocation
at runtime") has added the run-time allocation of gigantic pages.
However it actually works only at early stages of the system loading,
when the majority of memory is free. After some time the memory gets
fragmented by non-movable pages, so the chances to find a contiguous 1GB
block are getting close to zero. Even dropping caches manually doesn't
help a lot.
At large scale rebooting servers in order to allocate gigantic hugepages
is quite expensive and complex. At the same time keeping some constant
percentage of memory in reserved hugepages even if the workload isn't
using it is a big waste: not all workloads can benefit from using 1 GB
pages.
The following solution can solve the problem:
1) On boot time a dedicated cma area* is reserved. The size is passed
as a kernel argument.
2) Run-time allocations of gigantic hugepages are performed using the
cma allocator and the dedicated cma area
In this case gigantic hugepages can be allocated successfully with a
high probability, however the memory isn't completely wasted if nobody
is using 1GB hugepages: it can be used for pagecache, anon memory, THPs,
etc.
* On a multi-node machine a per-node cma area is allocated on each node.
Following gigantic hugetlb allocation are using the first available
numa node if the mask isn't specified by a user.
Usage:
1) configure the kernel to allocate a cma area for hugetlb allocations:
pass hugetlb_cma=10G as a kernel argument
2) allocate hugetlb pages as usual, e.g.
echo 10 > /sys/kernel/mm/hugepages/hugepages-1048576kB/nr_hugepages
If the option isn't enabled or the allocation of the cma area failed,
the current behavior of the system is preserved.
x86 and arm-64 are covered by this patch, other architectures can be
trivially added later.
The patch contains clean-ups and fixes proposed and implemented by Aslan
Bakirov and Randy Dunlap. It also contains ideas and suggestions
proposed by Rik van Riel, Michal Hocko and Mike Kravetz. Thanks!
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Andreas Schaufler <andreas.schaufler@gmx.de>
Acked-by: Mike Kravetz <mike.kravetz@oracle.com>
Acked-by: Michal Hocko <mhocko@kernel.org>
Cc: Aslan Bakirov <aslan@fb.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Rik van Riel <riel@surriel.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Link: http://lkml.kernel.org/r/20200407163840.92263-3-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I've noticed that there is no interface exposed by CMA which would let
me to declare contigous memory on particular NUMA node.
This patchset adds the ability to try to allocate contiguous memory on a
specific node. It will fallback to other nodes if the specified one
doesn't work.
Implement a new method for declaring contigous memory on particular node
and keep cma_declare_contiguous() as a wrapper.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Aslan Bakirov <aslan@fb.com>
Signed-off-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Michal Hocko <mhocko@kernel.org>
Cc: Andreas Schaufler <andreas.schaufler@gmx.de>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Link: http://lkml.kernel.org/r/20200407163840.92263-2-guro@fb.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
printk_deferred(), similarly to printk_safe/printk_nmi, does not
immediately attempt to print a new message on the consoles, avoiding
calls into non-reentrant kernel paths, e.g. scheduler or timekeeping,
which potentially can deadlock the system.
Those printk() flavors, instead, rely on per-CPU flush irq_work to print
messages from safer contexts. For same reasons (recursive scheduler or
timekeeping calls) printk() uses per-CPU irq_work in order to wake up
user space syslog/kmsg readers.
However, only printk_safe/printk_nmi do make sure that per-CPU areas
have been initialised and that it's safe to modify per-CPU irq_work.
This means that, for instance, should printk_deferred() be invoked "too
early", that is before per-CPU areas are initialised, printk_deferred()
will perform illegal per-CPU access.
Lech Perczak [0] reports that after commit 1b710b1b10 ("char/random:
silence a lockdep splat with printk()") user-space syslog/kmsg readers
are not able to read new kernel messages.
The reason is printk_deferred() being called too early (as was pointed
out by Petr and John).
Fix printk_deferred() and do not queue per-CPU irq_work before per-CPU
areas are initialized.
Link: https://lore.kernel.org/lkml/aa0732c6-5c4e-8a8b-a1c1-75ebe3dca05b@camlintechnologies.com/
Reported-by: Lech Perczak <l.perczak@camlintechnologies.com>
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Jann Horn <jannh@google.com>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: John Ogness <john.ogness@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull proc fix from Eric Biederman:
"A brown paper bag slipped through my proc changes, and syzcaller
caught it when the code ended up in your tree.
I have opted to fix it the simplest cleanest way I know how, so there
is no reasonable chance for the bug to repeat"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
proc: Use a dedicated lock in struct pid
Pull pwm updates from Thierry Reding:
"There's quite a few changes this time around.
Most of these are fixes and cleanups, but there's also new chip
support for some drivers and a bit of rework"
* tag 'pwm/for-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (33 commits)
pwm: pca9685: Fix PWM/GPIO inter-operation
pwm: Make pwm_apply_state_debug() static
pwm: meson: Remove redundant assignment to variable fin_freq
pwm: jz4740: Allow selection of PWM channels 0 and 1
pwm: jz4740: Obtain regmap from parent node
pwm: jz4740: Improve algorithm of clock calculation
pwm: jz4740: Use clocks from TCU driver
pwm: sun4i: Remove redundant needs_delay
pwm: omap-dmtimer: Implement .apply callback
pwm: omap-dmtimer: Do not disable PWM before changing period/duty_cycle
pwm: omap-dmtimer: Fix PWM enabling sequence
pwm: omap-dmtimer: Update description for PWM OMAP DM timer
pwm: omap-dmtimer: Drop unused header file
pwm: renesas-tpu: Drop confusing registered message
pwm: renesas-tpu: Fix late Runtime PM enablement
pwm: rcar: Fix late Runtime PM enablement
dt-bindings: pwm: renesas-tpu: Document more R-Car Gen2 support
pwm: meson: Fix confusing indentation
pwm: pca9685: Use gpio core provided macro GPIO_LINE_DIRECTION_OUT
pwm: pca9685: Replace CONFIG_PM with __maybe_unused
...
Pull more drm fixes from Dave Airlie:
"As expected, more fixes did turn up in the latter part of the week.
The drm_local_map build regression fix is here, along with temporary
disabling of the hugepage work due to some amdgpu related crashes.
Otherwise it's just a bunch of i915, and amdgpu fixes.
legacy:
- fix drm_local_map.offset type
ttm:
- temporarily disable hugepages to debug amdgpu problems.
prime:
- fix sg extraction
amdgpu:
- Various Renoir fixes
- Fix gfx clockgating sequence on gfx10
- RAS fixes
- Avoid MST property creation after registration
- Various cursor/viewport fixes
- Fix a confusing log message about optional firmwares
i915:
- Flush all the reloc_gpu batch (Chris)
- Ignore readonly failures when updating relocs (Chris)
- Fill all the unused space in the GGTT (Chris)
- Return the right vswing table (Jose)
- Don't enable DDI IO power on a TypeC port in TBT mode for ICL+ (Imre)
analogix_dp:
- probe fix
virtio:
- oob fix in object create"
* tag 'drm-next-2020-04-10' of git://anongit.freedesktop.org/drm/drm: (34 commits)
drm/ttm: Temporarily disable the huge_fault() callback
drm/bridge: analogix_dp: Split bind() into probe() and real bind()
drm/legacy: Fix type for drm_local_map.offset
drm/amdgpu/display: fix warning when compiling without debugfs
drm/amdgpu: unify fw_write_wait for new gfx9 asics
drm/amd/powerplay: error out on forcing clock setting not supported
drm/amdgpu: fix gfx hang during suspend with video playback (v2)
drm/amd/display: Check for null fclk voltage when parsing clock table
drm/amd/display: Acknowledge wm_optimized_required
drm/amd/display: Make cursor source translation adjustment optional
drm/amd/display: Calculate scaling ratios on every medium/full update
drm/amd/display: Program viewport when source pos changes for DCN20 hw seq
drm/amd/display: Fix incorrect cursor pos on scaled primary plane
drm/amd/display: change default pipe_split policy for DCN1
drm/amd/display: Translate cursor position by source rect
drm/amd/display: Update stream adjust in dc_stream_adjust_vmin_vmax
drm/amd/display: Avoid create MST prop after registration
drm/amdgpu/psp: dont warn on missing optional TA's
drm/amdgpu: update RAS related dmesg print
drm/amdgpu: resolve mGPU RAS query instability
...
Pull sound fixes from Takashi Iwai:
"A collection of small fixes gathered since the previous update.
ALSA core:
- Regression fix for OSS PCM emulation
ASoC:
- Trivial fixes in reg bit mask ops, DAPM, DPCM and topology
- Lots of fixes for Intel-based devices
- Minor fixes for AMD, STM32, Qualcomm, Realtek
Others:
- Fixes for the bugs in mixer handling in HD-audio and ice1724
drivers that were caught by the recent kctl validator
- New quirks for HD-audio and USB-audio
Also this contains a fix for EDD firmware fix, which slipped from
anyone's hands"
* tag 'sound-fix-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (35 commits)
ALSA: hda: Add driver blacklist
ALSA: usb-audio: Add mixer workaround for TRX40 and co
ALSA: hda/realtek - Add quirk for MSI GL63
ALSA: ice1724: Fix invalid access for enumerated ctl items
ALSA: hda: Fix potential access overflow in beep helper
ASoC: cs4270: pull reset GPIO low then high
ALSA: hda/realtek - Add HP new mute led supported for ALC236
ALSA: hda/realtek - Add supported new mute Led for HP
ASoC: rt5645: Add platform-data for Medion E1239T
ASoC: Intel: bytcr_rt5640: Add quirk for MPMAN MPWIN895CL tablet
ASoC: stm32: sai: Add missing cleanup
ALSA: usb-audio: Add registration quirk for Kingston HyperX Cloud Alpha S
ASoC: Intel: atom: Fix uninitialized variable compiler warning
ASoC: Intel: atom: Check drv->lock is locked in sst_fill_and_send_cmd_unlocked
ASoC: Intel: atom: Take the drv->lock mutex before calling sst_send_slot_map()
ASoC: SOF: Turn "firmware boot complete" message into a dbg message
ALSA: usb-audio: Add Pioneer DJ DJM-250MK2 quirk
ALSA: pcm: oss: Fix regression by buffer overflow fix (again)
ALSA: pcm: oss: Fix regression by buffer overflow fix
edd: Use scnprintf() for avoiding potential buffer overflow
...
Pull block fixes from Jens Axboe:
"Here's a set of fixes that should go into this merge window. This
contains:
- NVMe pull request from Christoph with various fixes
- Better discard support for loop (Evan)
- Only call ->commit_rqs() if we have queued IO (Keith)
- blkcg offlining fixes (Tejun)
- fix (and fix the fix) for busy partitions"
* tag 'block-5.7-2020-04-10' of git://git.kernel.dk/linux-block:
block: fix busy device checking in blk_drop_partitions again
block: fix busy device checking in blk_drop_partitions
nvmet-rdma: fix double free of rdma queue
blk-mq: don't commit_rqs() if none were queued
nvme-fc: Revert "add module to ops template to allow module references"
nvme: fix deadlock caused by ANA update wrong locking
nvmet-rdma: fix bonding failover possible NULL deref
loop: Better discard support for block devices
loop: Report EOPNOTSUPP properly
nvmet: fix NULL dereference when removing a referral
nvme: inherit stable pages constraint in the mpath stack device
blkcg: don't offline parent blkcg first
blkcg: rename blkcg->cgwb_refcnt to ->online_pin and always use it
nvme-tcp: fix possible crash in recv error flow
nvme-tcp: don't poll a non-live queue
nvme-tcp: fix possible crash in write_zeroes processing
nvmet-fc: fix typo in comment
nvme-rdma: Replace comma with a semicolon
nvme-fcloop: fix deallocation of working context
nvme: fix compat address handling in several ioctls
