The mv88e6xxx driver expects switches that are configured in single chip
addressing mode to have the MDIO address configured as 0. This is due to
the switch ADDR pins representing the single chip addressing mode as 0.
However depending on the device (e.g. MV88E6*41) the switch does not
respond on address 0 or any other address below 16 (the first port
address) in single chip addressing mode. This allows for other devices
to be on the same shared MDIO bus despite the switch being in single
chip addressing mode.
When using a switch that works this way it is not possible to configure
switch driver as single chip addressing via device tree, along with
another MDIO device on the same bus with address 0, as both devices
would have the same address of 0 resulting in mdiobus_register_device
-EBUSY errors for one of the devices with address 0.
In order to support this configuration the switch node can have its MDIO
address configured as 16 (the first address that the device responds
to). During initialization the driver will treat this address similar to
how address 0 is, however because this address is also a valid
multi-chip address (in certain switch models, but not all) the driver
will configure the SMI in single chip addressing mode and attempt to
detect the switch model. If the device is configured in single chip
addressing mode this will succeed and the initialization process can
continue. If it fails to detect a valid model this is because the switch
model register is not a valid register when in multi-chip mode, it will
then fall back to the existing SMI initialization process using the MDIO
address as the multi-chip mode address.
This detection method is safe if the device is in either mode because
the single chip addressing mode read is a direct SMI/MDIO read operation
and has no side effects compared to the SMI writes required for the
multi-chip addressing mode.
In order to implement this change, the reset gpio configuration is moved
to occur before any SMI initialization. This ensures that the device has
the same/correct reset gpio state for both mv88e6xxx_smi_init calls.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220427130928.540007-1-nathan@nathanrossi.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phy_attach_direct() first calls phy_init_hw() (which restores interrupt
settings through ->config_intr()), then calls phy_disable_interrupts().
So if phydev->interrupts was previously set to 1, interrupts are briefly
enabled, then disabled, which seems nonsensical.
If it was previously set to 0, interrupts are disabled twice, which is
equally nonsensical.
Deduplicate interrupt disablement.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/805ccdc606bd8898d59931bd4c7c68537ed6e550.1651040826.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, bpf and netfilter.
Current release - new code bugs:
- bridge: switchdev: check br_vlan_group() return value
- use this_cpu_inc() to increment net->core_stats, fix preempt-rt
Previous releases - regressions:
- eth: stmmac: fix write to sgmii_adapter_base
Previous releases - always broken:
- netfilter: nf_conntrack_tcp: re-init for syn packets only,
resolving issues with TCP fastopen
- tcp: md5: fix incorrect tcp_header_len for incoming connections
- tcp: fix F-RTO may not work correctly when receiving DSACK
- tcp: ensure use of most recently sent skb when filling rate samples
- tcp: fix potential xmit stalls caused by TCP_NOTSENT_LOWAT
- virtio_net: fix wrong buf address calculation when using xdp
- xsk: fix forwarding when combining copy mode with busy poll
- xsk: fix possible crash when multiple sockets are created
- bpf: lwt: fix crash when using bpf_skb_set_tunnel_key() from
bpf_xmit lwt hook
- sctp: null-check asoc strreset_chunk in sctp_generate_reconf_event
- wireguard: device: check for metadata_dst with skb_valid_dst()
- netfilter: update ip6_route_me_harder to consider L3 domain
- gre: make o_seqno start from 0 in native mode
- gre: switch o_seqno to atomic to prevent races in collect_md mode
Misc:
- add Eric Dumazet to networking maintainers
- dt: dsa: realtek: remove realtek,rtl8367s string
- netfilter: flowtable: Remove the empty file"
* tag 'net-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
tcp: fix F-RTO may not work correctly when receiving DSACK
Revert "ibmvnic: Add ethtool private flag for driver-defined queue limits"
net: enetc: allow tc-etf offload even with NETIF_F_CSUM_MASK
ixgbe: ensure IPsec VF<->PF compatibility
MAINTAINERS: Update BNXT entry with firmware files
netfilter: nft_socket: only do sk lookups when indev is available
net: fec: add missing of_node_put() in fec_enet_init_stop_mode()
bnx2x: fix napi API usage sequence
tls: Skip tls_append_frag on zero copy size
Add Eric Dumazet to networking maintainers
netfilter: conntrack: fix udp offload timeout sysctl
netfilter: nf_conntrack_tcp: re-init for syn packets only
net: dsa: lantiq_gswip: Don't set GSWIP_MII_CFG_RMII_CLK
net: Use this_cpu_inc() to increment net->core_stats
Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted
Bluetooth: hci_event: Fix creating hci_conn object on error status
Bluetooth: hci_event: Fix checking for invalid handle on error status
ice: fix use-after-free when deinitializing mailbox snapshot
ice: wait 5 s for EMP reset after firmware flash
ice: Protect vf_state check by cfg_lock in ice_vc_process_vf_msg()
...
Pull thermal control fixes from Rafael Wysocki:
"These take back recent chages that started to confuse users and fix up
an attr.show callback prototype in a driver.
Specifics:
- Stop warning about deprecation of the userspace thermal governor
and cooling device status interface, because there are cases in
which user space has to drive thermal management with the help of
them (Daniel Lezcano)
- Fix attr.show callback prototype in the int340x thermal driver
(Kees Cook)"
* tag 'thermal-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/governor: Remove deprecated information
Revert "thermal/core: Deprecate changing cooling device state from userspace"
thermal: int340x: Fix attr.show callback prototype
Pull power management fixes from Rafael Wysocki:
"These fix up recent intel_idle driver changes and fix some ARM cpufreq
driver issues.
Specifics:
- Fix issues with the Qualcomm's cpufreq driver (Dmitry Baryshkov,
Vladimir Zapolskiy).
- Fix memory leak with the Sun501 driver (Xiaobing Luo).
- Make intel_idle enable C1E promotion on all CPUs when C1E is
preferred to C1 (Artem Bityutskiy).
- Make C6 optimization on Sapphire Rapids added recently work as
expected if both C1E and C1 are "preferred" (Artem Bityutskiy)"
* tag 'pm-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
intel_idle: Fix SPR C6 optimization
intel_idle: Fix the 'preferred_cstates' module parameter
cpufreq: qcom-cpufreq-hw: Clear dcvs interrupts
cpufreq: fix memory leak in sun50i_cpufreq_nvmem_probe
cpufreq: qcom-cpufreq-hw: Fix throttle frequency value on EPSS platforms
cpufreq: qcom-hw: provide online/offline operations
cpufreq: qcom-hw: fix the opp entries refcounting
cpufreq: qcom-hw: fix the race between LMH worker and cpuhp
cpufreq: qcom-hw: drop affinity hint before freeing the IRQ
Pull ACPI fixes from Rafael WysockiL
"These fix up the ACPI processor driver after a change made during the
5.16 cycle that inadvertently broke falling back to shallower C-states
when C3 cannot be used.
Specifics:
- Make the ACPI processor driver avoid falling back to C3 type of
C-states when C3 cannot be requested (Ville Syrjälä)
- Revert a quirk that is not necessary any more after fixing the
underlying issue properly (Ville Syrjälä)"
* tag 'acpi-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "ACPI: processor: idle: fix lockup regression on 32-bit ThinkPad T40"
ACPI: processor: idle: Avoid falling back to C3 type C-states
Pull x86 platform driver fixes from Hans de Goede:
"Highlights:
- asus-wmi bug-fixes
- intel-sdsu bug-fixes
- build (warning) fixes
- couple of hw-id additions"
* tag 'platform-drivers-x86-v5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86/intel: pmc/core: change pmc_lpm_modes to static
platform/x86/intel/sdsi: Fix bug in multi packet reads
platform/x86/intel/sdsi: Poll on ready bit for writes
platform/x86/intel/sdsi: Handle leaky bucket
platform/x86: intel-uncore-freq: Prevent driver loading in guests
platform/x86: gigabyte-wmi: added support for B660 GAMING X DDR4 motherboard
platform/x86: dell-laptop: Add quirk entry for Latitude 7520
platform/x86: asus-wmi: Fix driver not binding when fan curve control probe fails
platform/x86: asus-wmi: Potential buffer overflow in asus_wmi_evaluate_method_buf()
tools/power/x86/intel-speed-select: fix build failure when using -Wl,--as-needed
Pull regulator fix from Mark Brown:
"A minor fix for the DT binding documentation of the rt5190a driver"
* tag 'regulator-fix-v5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: dt-bindings: Revise the rt5190a buck/ldo description
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Fix incorrect TCP connection tracking window reset for non-syn
packets, from Florian Westphal.
2) Incorrect dependency on CONFIG_NFT_FLOW_OFFLOAD, from Volodymyr Mytnyk.
3) Fix nft_socket from the output path, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nft_socket: only do sk lookups when indev is available
netfilter: conntrack: fix udp offload timeout sysctl
netfilter: nf_conntrack_tcp: re-init for syn packets only
====================
Link: https://lore.kernel.org/r/20220428142109.38726-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull gfs2 fix from Andreas Gruenbacher:
- No short reads or writes upon glock contention
* tag 'gfs2-v5.18-rc4-fix2' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
gfs2: No short reads or writes upon glock contention
This reverts commit 723ad91613
When client requests channel or ring size larger than what the server
can support the server will cap the request to the supported max. So,
the client would not be able to successfully request resources that
exceed the server limit.
Fixes: 723ad91613 ("ibmvnic: Add ethtool private flag for driver-defined queue limits")
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Link: https://lore.kernel.org/r/20220427235146.23189-1-drt@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Time-Specified Departure feature is indeed mutually exclusive with
TX IP checksumming in ENETC, but TX checksumming in itself is broken and
was removed from this driver in commit 82728b91f1 ("enetc: Remove Tx
checksumming offload code").
The blamed commit declared NETIF_F_HW_CSUM in dev->features to comply
with software TSO's expectations, and still did the checksumming in
software by calling skb_checksum_help(). So there isn't any restriction
for the Time-Specified Departure feature.
However, enetc_setup_tc_txtime() doesn't understand that, and blindly
looks for NETIF_F_CSUM_MASK.
Instead of checking for things which can literally never happen in the
current code base, just remove the check and let the driver offload
tc-etf qdiscs.
Fixes: acede3c5da ("net: enetc: declare NETIF_F_HW_CSUM and do it in software")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220427203017.1291634-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull xfs fixes from Dave Chinner:
- define buffer bit flags as unsigned to fix gcc-5 + c11 warnings
- remove redundant XFS fields from MAINTAINERS
- fix inode buffer locking order regression
* tag 'xfs-5.18-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: reorder iunlink remove operation in xfs_ifree
MAINTAINERS: update IOMAP FILESYSTEM LIBRARY and XFS FILESYSTEM
xfs: convert buffer flags to unsigned.
Merge a fix for the attr.show callback prototype in the int340x thermal
driver (Kees Cook).
* thermal-int340x:
thermal: int340x: Fix attr.show callback prototype
Check if the incoming interface is available and NFT_BREAK
in case neither skb->sk nor input device are set.
Because nf_sk_lookup_slow*() assume packet headers are in the
'in' direction, use in postrouting is not going to yield a meaningful
result. Same is true for the forward chain, so restrict the use
to prerouting, input and output.
Use in output work if a socket is already attached to the skb.
Fixes: 554ced0a6e ("netfilter: nf_tables: add support for native socket matching")
Reported-and-tested-by: Topi Miettinen <toiwoton@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Merge cpuidle fixes for 5.18-rc5:
- Make intel_idle enable C1E promotion on all CPUs when C1E is
preferred to C1 (Artem Bityutskiy).
- Make C6 optimization on Sapphire Rapids added recently work as
expected if both C1E and C1 are "preferred" (Artem Bityutskiy).
* pm-cpuidle:
intel_idle: Fix SPR C6 optimization
intel_idle: Fix the 'preferred_cstates' module parameter
Commit 00bfe02f47 ("gfs2: Fix mmap + page fault deadlocks for buffered
I/O") changed gfs2_file_read_iter() and gfs2_file_buffered_write() to
allow dropping the inode glock while faulting in user buffers. When the
lock was dropped, a short result was returned to indicate that the
operation was interrupted.
As pointed out by Linus (see the link below), this behavior is broken
and the operations should always re-acquire the inode glock and resume
the operation instead.
Link: https://lore.kernel.org/lkml/CAHk-=whaz-g_nOOoo8RRiWNjnv2R+h6_xk2F1J4TuSRxk1MtLw@mail.gmail.com/
Fixes: 00bfe02f47 ("gfs2: Fix mmap + page fault deadlocks for buffered I/O")
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Luiz Augusto von Dentz says:
====================
bluetooth pull request for net:
- Fix regression causing some HCI events to be discarded when they
shouldn't.
* tag 'for-net-2022-04-27' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth:
Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted
Bluetooth: hci_event: Fix creating hci_conn object on error status
Bluetooth: hci_event: Fix checking for invalid handle on error status
====================
Link: https://lore.kernel.org/r/20220427234031.1257281-1-luiz.dentz@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Dylan Hung says:
====================
Add reset deassertion for Aspeed MDIO
Add missing reset deassertion for Aspeed MDIO bus controller. The reset
is asserted by the hardware when power-on so the driver only needs to
deassert it. To be able to work with the old DT blobs, the reset is
optional since it may be deasserted by the bootloader or the previous
kernel.
V6:
- fix merge conflict for net-next
V5:
- fix error of dt_binding_check
V4:
- use ASPEED_RESET_MII instead of hardcoding in dt-binding example
V3:
- remove reset property from the required list of the device tree
bindings
- remove "Cc: stable@vger.kernel.org" from the commit messages
- add more description in the commit message of the dt-binding
V2:
- add reset property in the device tree bindings
- add reset assertion in the error path and driver remove
====================
Link: https://lore.kernel.org/r/20220427035501.17500-1-dylan_hung@aspeedtech.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add reset control properties into MDIO nodes. The 4 MDIO controllers in
AST2600 SOC share one reset control bit SCU50[3].
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add reset assertion/deassertion for Aspeed MDIO. There are 4 MDIO
controllers embedded in Aspeed AST2600 SOC and share one reset control
register SCU50[3]. To work with old DT blobs which don't have the reset
property, devm_reset_control_get_optional_shared is used in this change.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The AST2600 MDIO bus controller has a reset control bit and must be
deasserted before manipulating the MDIO controller. By default, the
hardware asserts the reset so the driver only need to deassert it.
Regarding to the old DT blobs which don't have reset property in them,
the reset deassertion is usually done by the bootloader so the reset
property is optional to work with them.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2022-04-27
We've added 85 non-merge commits during the last 18 day(s) which contain
a total of 163 files changed, 4499 insertions(+), 1521 deletions(-).
The main changes are:
1) Teach libbpf to enhance BPF verifier log with human-readable and relevant
information about failed CO-RE relocations, from Andrii Nakryiko.
2) Add typed pointer support in BPF maps and enable it for unreferenced pointers
(via probe read) and referenced ones that can be passed to in-kernel helpers,
from Kumar Kartikeya Dwivedi.
3) Improve xsk to break NAPI loop when rx queue gets full to allow for forward
progress to consume descriptors, from Maciej Fijalkowski & Björn Töpel.
4) Fix a small RCU read-side race in BPF_PROG_RUN routines which dereferenced
the effective prog array before the rcu_read_lock, from Stanislav Fomichev.
5) Implement BPF atomic operations for RV64 JIT, and add libbpf parsing logic
for USDT arguments under riscv{32,64}, from Pu Lehui.
6) Implement libbpf parsing of USDT arguments under aarch64, from Alan Maguire.
7) Enable bpftool build for musl and remove nftw with FTW_ACTIONRETVAL usage
so it can be shipped under Alpine which is musl-based, from Dominique Martinet.
8) Clean up {sk,task,inode} local storage trace RCU handling as they do not
need to use call_rcu_tasks_trace() barrier, from KP Singh.
9) Improve libbpf API documentation and fix error return handling of various
API functions, from Grant Seltzer.
10) Enlarge offset check for bpf_skb_{load,store}_bytes() helpers given data
length of frags + frag_list may surpass old offset limit, from Liu Jian.
11) Various improvements to prog_tests in area of logging, test execution
and by-name subtest selection, from Mykola Lysenko.
12) Simplify map_btf_id generation for all map types by moving this process
to build time with help of resolve_btfids infra, from Menglong Dong.
13) Fix a libbpf bug in probing when falling back to legacy bpf_probe_read*()
helpers; the probing caused always to use old helpers, from Runqing Yang.
14) Add support for ARCompact and ARCv2 platforms for libbpf's PT_REGS
tracing macros, from Vladimir Isaev.
15) Cleanup BPF selftests to remove old & unneeded rlimit code given kernel
switched to memcg-based memory accouting a while ago, from Yafang Shao.
16) Refactor of BPF sysctl handlers to move them to BPF core, from Yan Zhu.
17) Fix BPF selftests in two occasions to work around regressions caused by latest
LLVM to unblock CI until their fixes are worked out, from Yonghong Song.
18) Misc cleanups all over the place, from various others.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (85 commits)
selftests/bpf: Add libbpf's log fixup logic selftests
libbpf: Fix up verifier log for unguarded failed CO-RE relos
libbpf: Simplify bpf_core_parse_spec() signature
libbpf: Refactor CO-RE relo human description formatting routine
libbpf: Record subprog-resolved CO-RE relocations unconditionally
selftests/bpf: Add CO-RE relos and SEC("?...") to linked_funcs selftests
libbpf: Avoid joining .BTF.ext data with BPF programs by section name
libbpf: Fix logic for finding matching program for CO-RE relocation
libbpf: Drop unhelpful "program too large" guess
libbpf: Fix anonymous type check in CO-RE logic
bpf: Compute map_btf_id during build time
selftests/bpf: Add test for strict BTF type check
selftests/bpf: Add verifier tests for kptr
selftests/bpf: Add C tests for kptr
libbpf: Add kptr type tag macros to bpf_helpers.h
bpf: Make BTF type match stricter for release arguments
bpf: Teach verifier about kptr_get kfunc helpers
bpf: Wire up freeing of referenced kptr
bpf: Populate pairs of btf_id and destructor kfunc in btf
bpf: Adapt copy_map_value for multiple offset case
...
====================
Link: https://lore.kernel.org/r/20220427224758.20976-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Calling tls_append_frag when max_open_record_len == record->len might
add an empty fragment to the TLS record if the call happens to be on the
page boundary. Normally tls_append_frag coalesces the zero-sized
fragment to the previous one, but not if it's on page boundary.
If a resync happens then, the mlx5 driver posts dump WQEs in
tx_post_resync_dump, and the empty fragment may become a data segment
with byte_count == 0, which will confuse the NIC and lead to a CQE
error.
This commit fixes the described issue by skipping tls_append_frag on
zero size to avoid adding empty fragments. The fix is not in the driver,
because an empty fragment is hardly the desired behavior.
Fixes: e8f6979981 ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220426154949.159055-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf 2022-04-27
We've added 5 non-merge commits during the last 20 day(s) which contain
a total of 6 files changed, 34 insertions(+), 12 deletions(-).
The main changes are:
1) Fix xsk sockets when rx and tx are separately bound to the same umem, also
fix xsk copy mode combined with busy poll, from Maciej Fijalkowski.
2) Fix BPF tunnel/collect_md helpers with bpf_xmit lwt hook usage which triggered
a crash due to invalid metadata_dst access, from Eyal Birger.
3) Fix release of page pool in XDP live packet mode, from Toke Høiland-Jørgensen.
4) Fix potential NULL pointer dereference in kretprobes, from Adam Zabrocki.
(Masami & Steven preferred this small fix to be routed via bpf tree given it's
follow-up fix to Masami's rethook work that went via bpf earlier, too.)
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
xsk: Fix possible crash when multiple sockets are created
kprobes: Fix KRETPROBES when CONFIG_KRETPROBE_ON_RETHOOK is set
bpf, lwt: Fix crash when using bpf_skb_set_tunnel_key() from bpf_xmit lwt hook
bpf: Fix release of page_pool in BPF_PROG_RUN in test runner
xsk: Fix l2fwd for copy mode + busy poll combo
====================
Link: https://lore.kernel.org/r/20220427212748.9576-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge fixes from Andrew Morton:
"Two patches.
Subsystems affected by this patch series: mm/kasan and mm/debug"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
docs: vm/page_owner: use literal blocks for param description
kasan: prevent cpu_quarantine corruption when CPU offline and cache shrink occur at same time
kasan_quarantine_remove_cache() is called in kmem_cache_shrink()/
destroy(). The kasan_quarantine_remove_cache() call is protected by
cpuslock in kmem_cache_destroy() to ensure serialization with
kasan_cpu_offline().
However the kasan_quarantine_remove_cache() call is not protected by
cpuslock in kmem_cache_shrink(). When a CPU is going offline and cache
shrink occurs at same time, the cpu_quarantine may be corrupted by
interrupt (per_cpu_remove_cache operation).
So add a cpu_quarantine offline flags check in per_cpu_remove_cache().
[akpm@linux-foundation.org: add comment, per Zqiang]
Link: https://lkml.kernel.org/r/20220414025925.2423818-1-qiang1.zhang@intel.com
Signed-off-by: Zqiang <qiang1.zhang@intel.com>
Reviewed-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Sapphire Rapids (SPR) C6 optimization was added to the end of the
'spr_idle_state_table_update()' function. However, the function has a
'return' which may happen before the optimization has a chance to run.
And this may prevent the optimization from happening.
This is an unlikely scenario, but possible if user boots with, say,
the 'intel_idle.preferred_cstates=6' kernel boot option.
This patch fixes the issue by eliminating the problematic 'return'
statement.
Fixes: 3a9cf77b60 ("intel_idle: add core C6 optimization for SPR")
Suggested-by: Jan Beulich <jbeulich@suse.com>
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[ rjw: Minor changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Problem description.
When user boots kernel up with the 'intel_idle.preferred_cstates=4' option,
we enable C1E and disable C1 states on Sapphire Rapids Xeon (SPR). In order
for C1E to work on SPR, we have to enable the C1E promotion bit on all
CPUs. However, we enable it only on one CPU.
Fix description.
The 'intel_idle' driver already has the infrastructure for disabling C1E
promotion on every CPU. This patch uses the same infrastructure for
enabling C1E promotion on every CPU. It changes the boolean
'disable_promotion_to_c1e' variable to a tri-state 'c1e_promotion'
variable.
Tested on a 2-socket SPR system. I verified the following combinations:
* C1E promotion enabled and disabled in BIOS.
* Booted with and without the 'intel_idle.preferred_cstates=4' kernel
argument.
In all 4 cases C1E promotion was correctly set on all CPUs.
Also tested on an old Broadwell system, just to make sure it does not cause
a regression. C1E promotion was correctly disabled on that system, both C1
and C1E were exposed (as expected).
Fixes: da0e58c038 ("intel_idle: add 'preferred_cstates' module argument")
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[ rjw: Minor changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull ARM cpufreq fixes for 5.18-rc5 from Viresh Kumar:
"- Fix issues with the Qualcomm's cpufreq driver (Dmitry Baryshkov and
Vladimir Zapolskiy).
- Fix memory leak with the Sun501 driver (Xiaobing Luo)."
* tag 'cpufreq-arm-fixes-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
cpufreq: qcom-cpufreq-hw: Clear dcvs interrupts
cpufreq: fix memory leak in sun50i_cpufreq_nvmem_probe
cpufreq: qcom-cpufreq-hw: Fix throttle frequency value on EPSS platforms
cpufreq: qcom-hw: provide online/offline operations
cpufreq: qcom-hw: fix the opp entries refcounting
cpufreq: qcom-hw: fix the race between LMH worker and cpuhp
cpufreq: qcom-hw: drop affinity hint before freeing the IRQ
If we pass too short string to "hex2bin" (and the string size without
the terminating NUL character is even), "hex2bin" reads one byte after
the terminating NUL character. This patch fixes it.
Note that hex_to_bin returns -1 on error and hex2bin return -EINVAL on
error - so we can't just return the variable "hi" or "lo" on error.
This inconsistency may be fixed in the next merge window, but for the
purpose of fixing this bug, we just preserve the existing behavior and
return -1 and -EINVAL.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Fixes: b78049831f ("lib: add error checking to hex2bin")
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function hex2bin is used to load cryptographic keys into device
mapper targets dm-crypt and dm-integrity. It should take constant time
independent on the processed data, so that concurrently running
unprivileged code can't infer any information about the keys via
microarchitectural convert channels.
This patch changes the function hex_to_bin so that it contains no
branches and no memory accesses.
Note that this shouldn't cause performance degradation because the size
of the new function is the same as the size of the old function (on
x86-64) - and the new function causes no branch misprediction penalties.
I compile-tested this function with gcc on aarch64 alpha arm hppa hppa64
i386 ia64 m68k mips32 mips64 powerpc powerpc64 riscv sh4 s390x sparc32
sparc64 x86_64 and with clang on aarch64 arm hexagon i386 mips32 mips64
powerpc powerpc64 s390x sparc32 sparc64 x86_64 to verify that there are
no branches in the generated code.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull zonefs fixes from Damien Le Moal:
"Two fixes for rc5:
- Fix inode initialization to make sure that the inode flags are all
cleared.
- Use zone reset operation instead of close to make sure that the
zone of an empty sequential file in never in an active state after
closing the file"
* tag 'zonefs-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
zonefs: Fix management of open zones
zonefs: Clear inode information flags on inode creation
Pull MTD fixes from Miquel Raynal:
"Core fix:
- Fix a possible data corruption of the 'part' field in mtd_info
Rawnand fixes:
- Fix the check on the return value of wait_for_completion_timeout
- Fix wrong ECC parameters for mt7622
- Fix a possible memory corruption that might panic in the Qcom
driver"
* tag 'mtd/fixes-for-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: qcom: fix memory corruption that causes panic
mtd: fix 'part' field data corruption in mtd_info
mtd: rawnand: Fix return value check of wait_for_completion_timeout
mtd: rawnand: fix ecc parameters for mt7622
Sparse reports this issue
core.c: note: in included file:
core.h:239:12: warning: symbol 'pmc_lpm_modes' was not declared. Should it be static?
Global variables should not be defined in headers. This only works
because core.h is only included by core.c. Single file use
variables should be static, so change its storage-class specifier
to static.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: David E. Box <david.e.box@linux.intel.com>
Link: https://lore.kernel.org/r/20220423123048.591405-1-trix@redhat.com
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
