Add the serdev (UART) transport for the Realtek PSE MCU core. It registers
the MCU as a serdev device and provides the send/recv callbacks the core
uses to exchange the 12-byte frames, receiving asynchronously via the
serdev receive_buf callback.
The baud rate defaults to 19200 and can be overridden per board with the
"current-speed" property.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20260813222036.873930-5-jelonek.jonas@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add the I2C/SMBus transport for the Realtek PSE MCU core. It registers
the MCU on an I2C bus and provides the send/recv callbacks the core
uses to exchange the 12-byte frames.
The MCU firmware expects one of two framings on the I2C bus, and which one
is part of the compatible: '-smbus' (reads carry a leading command byte
and a repeated start) or raw '-i2c' (bare block writes and reads). The
match data flags the raw-I2C case; SMBus is the default because that's
what the majority of devices uses.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20260813222036.873930-4-jelonek.jonas@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A range of managed Realtek-based PoE switches use a small microcontroller
on the PCB to front the actual PSE silicon. The host CPU talks to that
MCU over I2C/SMBus or UART using a fixed 12-byte request/response
protocol with a trailing checksum; the PSE chips are managed by the MCU
and are not accessed directly. Two generations of the protocol exist -
both Realtek's - diverging in opcode numbering and a few response
layouts; the driver handles this with a per-dialect opcode table and
parser hooks for the responses that differ, selected by the compatible.
The specific PSE chip behind the MCU is detected at runtime and only
influences per-chip constants (power scaling and the per-port cap).
This core module implements the protocol, message framing, the dialect
machinery and the pse_controller_ops glue, and exports a registration
helper for transport modules. The I2C and UART transports that drive it
follow in the next patches; the core (PSE_REALTEK_MCU) is selected
automatically by those transports and is not user-selectable on its own.
The realtek-pse-mcu-* files and PSE_REALTEK_MCU* symbols match the
realtek,pse-mcu-* compatibles (see the binding for the naming rationale).
The two protocol generations - gen1 on older Broadcom-PSE boards, gen2 on
Realtek's own PSE silicon - are both Realtek's, handled by the same shared
core, each selecting its dialect via the compatible.
Power budgeting is left to the MCU firmware; the driver advertises
PSE_BUDGET_EVAL_STRAT_DYNAMIC accordingly.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://patch.msgid.link/20260813222036.873930-3-jelonek.jonas@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a binding for the microcontroller (MCU) that fronts the PSE silicon
on a range of managed Realtek-based switches. The host talks only to the
MCU, over I2C/SMBus or UART, using a fixed message-based protocol; the
PSE chips behind it never appear on the bus.
The device is the MCU together with its Realtek firmware: the firmware
and its host protocol are what the binding describes, not the
general-purpose microcontroller they run on. The PSE silicon behind the
MCU (Realtek or Broadcom) is reported by the MCU and detected at runtime,
so it is not described here - hence the 'realtek' vendor prefix.
Two protocol generations exist, both Realtek's, selected by the
compatible: gen1 on older boards (fronting Broadcom PSE silicon) and gen2,
the altered protocol used with Realtek's own PSE silicon. On an I2C
attachment the framing the MCU firmware expects is part of the compatible
as well - '-smbus' or raw '-i2c'; a UART attachment carries no framing
suffix, as the transport is given by the parent serial node.
Each board additionally carries a device-specific compatible that falls
back to one of the protocol compatibles above. Drivers bind on the
protocol compatible; the device-specific string identifies the board and
reserves a place for a future per-board quirk without having to retrofit
device trees already in the field.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20260813222036.873930-2-jelonek.jonas@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The dedicated hardware timestamp RX queue is allocated with q->index
equal to lif->ionic->nrxqs_per_lif. The normal txqcqs array only
contains the regular queue pairs, so using that index to set rxq->partner
can read one entry past txqcqs[] and then write through the derived
pointer.
Only link RX/TX partners for normal queue-pair indexes. Leave the hwstamp
RX queue unpaired, and make the XDP_TX path abort cleanly if an RX queue
has no TX partner.
Fixes: 8eeed8373e ("ionic: Add XDP_TX support")
Reviewed-by: Si-Wei Liu <si-wei.liu@oracle.com>
Reviewed-by: Shannon Nelson <sln@onemain.com>
Cc: stable@vger.kernel.org
Signed-off-by: Anand Khoje <anand.a.khoje@oracle.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Brett Creeley <brett.creeley@amd.com>
Link: https://patch.msgid.link/20260813083705.454897-1-anand.a.khoje@oracle.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When polling for completion returned completion with error,
parse some more details: WQE count and syndrome number.
Also, extract all the long value-to-string if conditions
to a short value-to-string functions: do it for rule
resize state, rule status, and syndrome.
v2: removed duplicated QPN print
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20260816142045.3289452-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For the mailbox ABI, device properties will come from a different
source compared to the AdminQ mode. To accommodate the new source
when the mailbox ABI is added, add a few helper functions to set a
few device properties. Those functions are:
- gve_set_queue_properties() to set no. of pages for QPL mode and
number of queues in general
- gve_set_mtu()
- gve_set_mac()
This is just code movement, no functional change.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20260814021406.3044324-4-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the interest of commonizing code, refactor gve_probe()
and gve_init_priv() with a few helper functions that can
be expanded and utilized in upcoming patches that add the
mailbox ABI to the driver. The helper functions are:
- gve_set_num_ntfy_blks()
- gve_set_num_queues()
Reorder code to combine lines that accomplish a similar objective
like setting defaults. Move setting HW-GRO and UDP GSO support out
of an Adminq method into gve_init_priv().
These changes are just code movement, no functional change.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Jordan Rhee <jordanrhee@google.com>
Signed-off-by: Harshitha Ramamurthy <hramamurthy@google.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://patch.msgid.link/20260814021406.3044324-3-hramamurthy@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jori Koolstra says:
====================
net: af_unix: useful handling of LSM denials on SCM_RIGHTS
Right now if some LSM denies an AF_UNIX socket peer to receive a
SCM_RIGHTS fd, the SCM_RIGHTS fd array will be cut short at
that point, and MSG_CTRUNC is set on return of recvmsg(2). This is
highly problematic behaviour, because it leaves the receiver
wondering what happened. As per man page MSG_CTRUNC is supposed to
indicate that the control buffer was sized too short, but suddenly
a permission error might result in the exact same flag being set.
Moreover, the receiver has no chance to determine how many fds got
originally sent and how many were suppressed.[1]
Add a SO_RIGHTS_NOTRUNC option to UNIX sockets to enable more useful
handling of LSM denials when receiving SCM_RIGHTS messages: instead of
truncating the message at the first blocked fd, keep every fd slot
and store the LSM errno in the blocked slot. This option is inherited
by the accept()-ed socket when set on the listen() socket.
[1]: https://github.com/uapi-group/kernel-features#useful-handling-of-lsm-denials-on-scm_rights
====================
Link: https://patch.msgid.link/20260813162818.149248-1-jkoolstra@xs4all.nl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tests SCM_RIGHTS fd passing on a socket with the new socket option
SO_RIGHTS_NOTRUNC turned on. To hook into the security_file_receive()
call, BPF is used. The BPF program shares a hashmap with userspace that
lists the inos to be blocked (of the receiver tgid).
Signed-off-by: Jori Koolstra <jkoolstra@xs4all.nl>
Link: https://patch.msgid.link/20260814172806.158954-1-jkoolstra@xs4all.nl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Right now if some LSM such as Smack denies an AF_UNIX socket peer to
receive an SCM_RIGHTS fd, the SCM_RIGHTS fd array will be cut short at
that point, and MSG_CTRUNC is set on return of recvmsg(). This is
highly problematic behaviour, because it leaves the receiver
wondering what happened. As per man page MSG_CTRUNC is supposed to
indicate that the control buffer was sized too short, but suddenly
a permission error might result in the exact same flag being set.
Moreover, the receiver has no chance to determine how many fds got
originally sent and how many were suppressed.[1]
Add a SO_RIGHTS_NOTRUNC option to UNIX sockets to enable more useful
handling of LSM denials when receiving SCM_RIGHTS messages: instead of
truncating the message at the first blocked fd, keep every fd slot
and store the LSM errno in the blocked slot. The socket option is
inherited by the child accept() socket if set on the listen() socket.
[1]: https://github.com/uapi-group/kernel-features#useful-handling-of-lsm-denials-on-scm_rights
Reviewed-by: Christian Brauner (Amutable) <brauner@kernel.org>
Signed-off-by: Jori Koolstra <jkoolstra@xs4all.nl>
Link: https://patch.msgid.link/20260813162818.149248-4-jkoolstra@xs4all.nl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
unix_setsockopt() and the SOCK_CUSTOM_SOCKOPT flag were only wired up
for SOCK_STREAM (introduced along with the stream-only SO_INQ).
Consequently custom AF_UNIX options are unreachable on SOCK_DGRAM and
SOCK_SEQPACKET: those setsockopt() calls bypass unix_setsockopt() and
fall through to the generic sock_setsockopt(), failing with
-ENOPROTOOPT.
Set SOCK_CUSTOM_SOCKOPT for every AF_UNIX socket type in unix_create(), and
also for accepted sockets in unix_accept() (reachable for stream and
seqpacket).
This is a prerequisite for making SO_RIGHTS_NOTRUNC settable on all AF_UNIX
socket types.
Signed-off-by: Jori Koolstra <jkoolstra@xs4all.nl>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Link: https://patch.msgid.link/20260813162818.149248-2-jkoolstra@xs4all.nl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Introduce iXD driver
Larysa Zaremba says:
This patch series adds the iXD driver, which supports the Intel(R)
Control Plane PCI Function on Intel E2100 and later IPUs and FNICs.
It facilitates a centralized control over multiple IDPF PFs/VFs/SFs
exposed by the same card. The reason for the separation is to be able
to offload the control plane to the host different from where the data
plane is running.
This is the first phase in the release of this driver where we implement the
initialization of the core PCI driver. Subsequent phases will implement
advanced features like usage of idpf ethernet aux device, link management,
NVM update via devlink, switchdev port representors, data and exception path,
flow rule programming, etc.
The first phase entails the following aspects:
1. Additional libie functionalities:
Patches 1-5 introduce additional common library API for drivers to
communicate with the control plane through mailbox communication.
A control queue is a hardware interface which is used by the driver
to interact with other subsystems (like firmware). The library APIs
allow the driver to setup and configure the control queues to send and
receive virtchnl messages. The library has an internal bookkeeping
(XN API) mechanism to keep track of the send messages. It supports both
synchronous as well as asynchronous way of handling the messages. The
library also handles the timeout internally for synchronous messages
using events. This reduces the driver's overhead in handling the timeout
error cases.
The current patch series supports only APIs that are needed for device
initialization. These include APIs in the libie_pci module:
* Allocating/freeing the DMA memory and mapping the MMIO regions for
BAR0, read/write APIs for drivers to access the MMIO memory
and libie_cp module:
* Control queue initialization and configuration
* Transport initialization for bookkeeping
* Blocking and asynchronous mailbox transactions
Once the mailbox is initialized, the drivers can send and receive virtchnl
messages to/from the control plane.
The modules above are not supposed to be linked with the main libie library,
but do share the folder with it.
2. idpf:
Patches 6-11 refactor the idpf driver to use the libie APIs for control
queue configuration, virtchnl transaction, device initialization
and reset and adjust related code accordingly.
3. ixd:
Patches 12-15 add the ixd driver and implement multiple pieces of the
initialization flow as follows:
* Add the ability to load
* A reset is issued to ensure a clean device state, followed by
initialization of the mailbox
* Device capabilities:
As part of initialization, the driver has to determine what the device is
capable of (ex. max queues, vports, etc). This information is obtained from
the firmware and stored by the driver.
* Enable initial support for the devlink interface
* '200GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ixd: add devlink support
ixd: add the core initialization
ixd: add reset checks and initialize the mailbox
ixd: add basic driver framework for Intel(R) Control Plane Function
idpf: print a debug message and bail in case of non-event ctlq message
idpf: make mbx_task queueing and cancelling more consistent
idpf: refactor idpf to use libie control queues
idpf: refactor idpf to use libie_pci APIs
idpf: remove unused code for getting RSS info from device
idpf: remove 'vport_params_reqd' field
libie: add bookkeeping support for control queue messages
libie: add control queue support
libeth: allow to create fill queues without NAPI
libie: add PCI device initialization helpers to libie
virtchnl: move virtchnl and virtchnl2 headers to 'include/linux/net/intel'
====================
Link: https://patch.msgid.link/20260812212532.905873-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Satish Kharat says:
====================
enic: SR-IOV V2 admin channel and MBOX protocol
This series adds the admin channel infrastructure and mailbox (MBOX)
protocol needed for V2 SR-IOV support in the enic driver.
The V2 SR-IOV design uses a direct PF-VF communication channel built on
dedicated WQ/RQ/CQ hardware resources and an MSI-X interrupt.
This series touches enic_remove(), which is also modified by a fix
already applied to net:
enic: fix tx_hang_reset use-after-free on device removal
https://git.kernel.org/netdev/net/c/ec680ea4ba1b
That fix was previously carried at the head of this series (patch 1 in
v10-v12); it has been split out and applied to net separately. This
net-next series no longer includes it and applies cleanly on current
net-next, which already contains that fix (via the net -> net-next
merge); the overlapping enic_remove() teardown-ordering change is
incorporated in this series.
Firmware capability and admin channel infrastructure (patches 1-4):
- Probe-time firmware feature check for V2 SR-IOV support
- Admin channel open/close, RQ buffer management, CQ service
with MSI-X interrupt and workqueue-based polling
MBOX protocol and VF enable (patches 5-10):
- MBOX message types, core send/receive, PF and VF handlers
- V2 SR-IOV enable wiring with admin channel setup
- V2 VF probe with admin channel and PF registration
Patch 11 completes reset recovery for V2 VFs: the reset paths added
earlier in the series re-establish the admin channel only for the PF,
which left a VF unregistered and unable to exchange MBOX traffic after
a reset taken on the VF.
Known follow-ups (not blocking this series; the V2 PF data path is not
yet activated and V2 VFs are brought up only in a later series that wires
.sriov_configure):
- Full request/reply correlation by msg_num requires the MBOX peer to
echo the request number; this series retains the existing
single-outstanding-request model with reply-type gating.
- PF-side registration synchronization, initial link-state retry, and
admin control-message throttling will be completed alongside the
.sriov_configure enablement.
====================
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-0-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The reset paths (enic_reset/enic_tx_hang_reset) tore down and re-opened
the V2 admin/MBOX channel only for the PF: the close/reopen was gated on
enic_sriov_enabled() && vf_type == ENIC_VF_TYPE_V2, which is never true on
a VF (vf_type is set only on the PF; VFs are identified by
enic_is_sriov_vf_v2()). A VF-initiated reset therefore left the VF admin
QP wiped by the reset but never re-opened, and the VF never re-registered
with the PF, so VF<->PF MBOX traffic (currently link state)
stopped working until the VF was re-probed.
Factor the decision into enic_has_admin_chan() (true for a V2 PF while
SR-IOV is enabled and for every V2 VF) and the reopen sequence into
enic_admin_chan_reopen(). For a VF the helper additionally re-runs the
probe-time handshake (enic_mbox_vf_capability_check() +
enic_mbox_vf_register()) so the PF learns about the VF again; for a PF it
re-pushes the current link state as before.
Before reopening, invalidate the VF's local registration flag. The reset
only wipes the VF's admin QP, not the PF's software vf_state (that changes
only via the register/unregister MBOX handlers), so the PF may still hold
a stale "registered" until the VF re-registers. Locally, a failed reopen
or re-handshake must not leave a stale registered state that a later
teardown would try to unregister over a dead channel.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-11-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a V2 SR-IOV VF probes, initialize the MBOX protocol, open the
admin channel, perform the capability check with the PF, and register
with the PF. This establishes the PF-VF communication path that the PF
uses to send link state notifications.
The admin channel and MBOX registration happen after enic_dev_init()
(which discovers admin channel resources) and before register_netdev()
so the VF is fully initialized before the interface is visible to
userspace.
A V2 VF whose firmware did not provision admin WQ/RQ/CQ resources
fails probe with -ENODEV from enic_admin_channel_open(); the admin
channel is a hard requirement for V2 VFs.
enic_mbox_init() installs the receive handler and resets the message
sequence number before enic_admin_channel_open() unmasks the admin
interrupt, so a completion can never arrive before the handler is in
place.
On remove, the VF unregisters from the PF and closes its admin channel
before tearing down data path resources.
V2 VFs are not provisioned with an RES_TYPE_SRIOV_INTR resource by
firmware, so bypass that check in the admin channel capability
detection for V2 VFs. The PF still requires this resource.
The admin MSI-X vector reserved by enic_set_intr_mode()
is used for the admin channel interrupt.
enic_adjust_resources() ensures the reserved slot is within
intr_avail bounds even at maximum queue configurations. The
admin INTR uses a RES_TYPE_INTR_CTRL slot shared with the
data path.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-10-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend enic_sriov_configure() to handle V2 SR-IOV VFs. When the PF
detects V2 VF device IDs, the enable path allocates per-VF MBOX state,
initializes the MBOX protocol, opens the admin channel, and then calls
pci_enable_sriov(). The admin channel must be ready before VFs are
created so that VF drivers can immediately begin the MBOX capability
and registration handshake during their probe.
The enic_sriov_configure() dispatcher and its V2 helpers
(enic_sriov_v2_enable, enic_sriov_v2_disable) are defined here but
intentionally not yet wired into struct pci_driver via
.sriov_configure -- hence the __maybe_unused annotations. This
series introduces only the admin channel and MBOX infrastructure;
sysfs-driven V2 enable/disable will be activated in a follow-up
patch by adding ".sriov_configure = enic_sriov_configure," to
enic_driver.
Because .sriov_configure is not registered yet, enic_sriov_configure()
cannot run concurrently with the rtnl-protected reset paths
(enic_reset(), enic_tx_hang_reset()) in this series, so there is no
reachable locking race between SR-IOV enable/disable and reset. The
follow-up patch that wires the callback will add the necessary
serialization against those paths. Note that simply taking rtnl_lock()
around the enable path is not viable, because pci_enable_sriov()
triggers VF probe and register_netdev(), which themselves acquire rtnl;
the wiring patch therefore uses finer-grained serialization.
The disable path first clears ENIC_SRIOV_ENABLED and flushes the
link-notify work, so no further VF link-state broadcast can run, then
calls pci_disable_sriov() (VF drivers unregister via MBOX), closes the
admin channel, and frees per-VF state. Clearing the flag and flushing
the work before vf_state is freed closes a use-after-free window
against the link-notify path.
Notify registered VFs of PF link transitions: enic_link_check()
schedules link_notify_work on each carrier up/down edge, and the work
handler sends PF_LINK_STATE_NOTIF to the VFs from process context.
The broadcast cannot run directly in enic_link_check() because the
MBOX send path may sleep and link check runs in the notify timer/ISR
context.
On a V2 VF the admin-channel (PF) link-state notification is the sole
authority for carrier state, so enic_link_check() returns early for
such VFs. As a side effect the VF retains the firmware-provided static
Rx interrupt coalescing (config.intr_timer_usec) rather than PF-driven
speed-adaptive coalescing; this is intentional, as adaptive Rx
coalescing is a PF-only responsibility for V2 VFs.
Re-establish the admin/MBOX channel across a PF reset. enic_reset()
and enic_tx_hang_reset() fully close the admin channel before the
soft/hang reset (which wipes all hardware queues, including the admin
WQ/RQ), then reopen it and re-run enic_mbox_init() after the data path
is back up, and re-push the current link state to registered VFs.
Reject VF port profile requests when V2 SR-IOV is active
(enic_is_valid_pp_vf), since enic->pp is not reallocated for V2 VFs
and the V2 protocol uses MBOX instead of port profiles.
Update enic_remove() to run enic_dev_deinit() and vnic_dev_close()
after SR-IOV teardown, so the PF device remains functional while VFs
are being cleaned up. This ordering applies to both V1 and V2 SR-IOV
paths.
Restrict the probe-time SR-IOV auto-enable to the legacy VF types (V1
and usNIC). A V2-capable adapter whose firmware lacks V2 support is
downgraded to ENIC_VF_TYPE_NONE, and V2 VFs require the admin channel
which is only brought up via sysfs enic_sriov_configure(); neither
must be auto-enabled through the legacy pci_enable_sriov() path at
probe.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-9-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement VF-side mailbox message processing for SR-IOV V2
admin channel communication.
VF receive handlers:
- VF_CAPABILITY_REPLY: store PF protocol version, signal
completion
- VF_REGISTER_REPLY: mark VF as registered, signal completion
- VF_UNREGISTER_REPLY: mark VF as unregistered, signal
completion
- PF_LINK_STATE_NOTIF: update carrier state via
netif_carrier_on/off, send ACK back to PF
VF initiation functions for the probe-time handshake:
- enic_mbox_vf_capability_check: send capability request,
wait for PF reply via completion
- enic_mbox_vf_register: send register request, wait for
PF confirmation via completion
- enic_mbox_vf_unregister: send unregister request, wait
for PF confirmation
The wait helper (enic_mbox_wait_reply) uses
wait_for_completion_timeout, signaled when the admin ISR and
CQ-poll/dispatch workqueue pipeline delivers the reply message.
mbox_expected_reply is written by the request thread and read by the
admin CQ poll/dispatch context that runs the receive handlers; annotate
those accesses with READ_ONCE()/WRITE_ONCE() under the
single-outstanding-reply invariant.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-8-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement PF-side mailbox message processing for SR-IOV V2
admin channel communication.
When the PF receives messages from VFs, the dispatch routes
them to type-specific handlers:
- VF_CAPABILITY_REQUEST: reply with protocol version 1
- VF_REGISTER_REQUEST: send the register reply, mark the
VF registered on success, then send PF_LINK_STATE_NOTIF
reflecting the PF's current carrier state
- VF_UNREGISTER_REQUEST: mark VF unregistered, send reply
- PF_LINK_STATE_ACK: log errors from VF acknowledgment
Per-VF state (struct enic_vf_state) is tracked via enic->vf_state
which will be allocated when SRIOV V2 is enabled.
Remove the CONFIG_PCI_IOV guard from num_vfs in struct enic. The
PF handlers reference enic->num_vfs for VF ID bounds checking in
enic_mbox.c, which is compiled unconditionally. The field must be
visible regardless of CONFIG_PCI_IOV to avoid build failures.
Add enic_mbox_send_link_state() helper for PF-initiated link
state notifications.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-7-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement the mailbox protocol engine used for PF-VF communication
over the admin channel.
The send path (enic_mbox_send_msg) builds a message with a common
header, DMA-maps it, posts a single WQ descriptor with the
destination vnic ID encoded in the VLAN tag field, and polls
the WQ CQ for completion.
The total message length is computed as a size_t, and the payload is
bounded before the send lock is taken: a payload larger than the admin
buffer minus the header is rejected with -EINVAL. This keeps the length
sum from wrapping and stops the on-the-wire u16 length from overflowing
or the DMA buffer from being overrun.
MBOX sends are gated by enic->mbox_send_disabled: enic_mbox_send_msg()
returns early while it is set. It is set at the very start of both
enic_admin_channel_open() and enic_admin_channel_close(), and is
cleared in enic_admin_channel_open() only once the admin WQ/RQ/CQ and
interrupt are fully allocated, programmed and enabled. Keeping it set
for the whole open sequence means an early failure that returns before
the channel is ready (as well as a not-yet-ready or torn-down channel)
leaves sends disabled, so a concurrent sender can never race an MBOX
send against a half-open or freed admin_wq.
The receive path (enic_mbox_recv_handler) is installed as the admin
RQ callback and validates incoming message headers. PF/VF-specific
dispatch will be added in subsequent commits.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-6-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define the mailbox protocol structures for PF-VF communication:
message header, generic reply, and per-message-type payloads for
capability negotiation, VF registration/unregistration, and link
state notification/acknowledgment.
Include linux/types.h and linux/bits.h for __le16/__le32/__le64
and BIT() used in the header.
Message types use an even=request / odd=reply convention. The
header carries source and destination VNIC IDs, a per-channel
message sequence number, and the total message length.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-5-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add completion queue (CQ) service for the admin channel work queue
(WQ) and receive queue (RQ), driven by a dedicated MSI-X interrupt
and a workqueue-based CQ poller.
The admin WQ CQ service advances the completion ring and returns the
number of descriptors consumed. The admin RQ CQ service does the
same for receive completions and copies each received message out of
its pre-posted DMA buffer into a dynamically allocated queue entry.
The pending queue is bounded to ENIC_ADMIN_MSG_MAX (256) entries so a
buggy or hostile VF cannot drive the host out of memory; messages are
enqueued for deferred dispatch by a separate work_struct so the CQ
poller stays short.
When the MSI-X interrupt fires, the ISR schedules the CQ poll work.
The work handler drains all pending completions, kicks message
dispatch if work was done, and returns credits to unmask the
interrupt. The admin vector is kept masked from the time the IRQ is
requested until the rings are initialised and filled during channel
open, so an early or spurious interrupt cannot run the poll handler
against uninitialised rings.
The poll handler snapshots the pending credit count before draining
the CQ so it acknowledges exactly what the hardware reported for this
interrupt; any credits that accrue during draining are serviced by the
next interrupt. The credit write also sets the mask bit to re-arm the
vector, and that unmask is applied independently of the credit count,
so the vector is re-armed even when zero credits are returned -- which
matters here because the admin channel is not re-polled like the NAPI
data path.
If an admin RQ buffer refill fails under transient memory pressure,
reschedule the CQ poll work itself after a short delay to retry the
refill and re-arm the RQ, so the admin channel cannot stall when the
ring would otherwise be left empty with no completion to drive the
next refill. The poll work is a delayed_work for this reason; routing
the retry through it keeps the admin RQ ring owned by a single context
so refills never run concurrently.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-4-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The admin receive queue needs pre-posted DMA buffers for incoming
mailbox messages from VFs. Each buffer is a kzalloc'd region mapped
for DMA (2048 bytes, sufficient for any MBOX message). Zeroing on
allocation ensures that if a completion reports more bytes than
hardware actually DMA-wrote, the parser reads zero padding rather
than uninitialised heap contents.
Add enic_admin_rq_fill(gfp) to post buffers at open time, and
enic_admin_rq_drain() to unmap and free them at close time.
Wire both into the admin channel open/close paths. The gfp_t
parameter lets the caller pass the allocation context; both current
callers -- channel open and the CQ-poll work handler that refills
after draining (added in the next patch) -- run in process context
and use GFP_KERNEL.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-3-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The V2 SR-IOV design uses a dedicated admin channel (WQ/RQ/CQ
resources plus an MSI-X interrupt) for PF-VF mailbox communication rather
than firmware-proxied devcmds.
Introduce enic_admin_channel_open() and enic_admin_channel_close().
Open allocates and initialises the admin WQ, RQ, and two CQs (one per
direction), then issues CMD_QP_TYPE_SET to tell firmware the queues are
admin-type. Close reverses the sequence.
enic_admin_wq_buf_clean() unmaps and frees any WQ buffers still held
at close time, fixing a DMA mapping leak when a send times out.
Add CMD_QP_TYPE_SET (97), QP_TYPE_ADMIN/DATA, and QP_ENABLE/QP_DISABLE
defines to vnic_devcmd.h. Add VNIC_CQ_* named constants to vnic_cq.h
so CQ initialisation parameters are self-documenting from their first
introduction.
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-2-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During PF probe, query the firmware get-supported-feature interface
to verify that the running firmware supports V2 SR-IOV. Firmware
version 5.3(4.72) and later report VIC_FEATURE_SRIOV via
CMD_GET_SUPP_FEATURE_VER. If the firmware does not support the
feature, set vf_type to ENIC_VF_TYPE_NONE and log a warning so the
admin knows a firmware upgrade is needed.
The V2 admin-channel and MBOX bring-up added later in this series is
gated on ENIC_VF_TYPE_V2, so this downgrade keeps those paths from
running on firmware that does not support V2 SR-IOV.
VIC_FEATURE_SRIOV is assigned the explicit value 4 to match the
firmware ABI. Slot 3 (firmware's VIC_FEATURE_PTP) is reserved with
a comment rather than a placeholder enum entry, since PTP is not
used by the upstream driver.
Suggested-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Satish Kharat <satishkh@cisco.com>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20260812-enic-sriov-v2-admin-channel-v2-v13-1-b3809e448aba@cisco.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: misc. features for v7.3
This series contains a few independent new features, and small fixes for
net-next:
- Patch 1: Add WARN_ON_ONCE guards around extra_subflows to catch issues
with this counter, similar to what is done with other PM counters.
- Patches 2-3: Follow-up patches to remove data_ack field from struct
mptcp_ext -- now unused after recent fixes -- and makes a userspace PM
helper static.
- Patch 4: Honour tcp_rto_{min_us,max_ms} sysctls for MPTCP-level
retransmit timers like with DATA_FIN's and fallback timeout.
- Patches 5-6: Add per-event MIB counters for MPTCP_RST_EMPTCP resets to
help to spot such situations in production.
- Patches 7-9: Small pcap-related improvements in the selftests.
- Patch 10: Fix compiler warning in the selftests.
- Patch 11: Avoid a buffer overflow when misusing the mptcp_diag tool
from the selftests.
====================
Link: https://patch.msgid.link/20260812-net-next-mptcp-misc-feat-7-3-v1-0-1905a818f6cb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
get_subflow_info() parses the subflow address string with:
char saddr[64], daddr[64];
ret = sscanf(subflow_addrs, "%[^:]:%d %[^:]:%d",
saddr, &sport, daddr, &dport);
The subflow_addrs buffer holds up to 1024 bytes and is taken directly
from the command line ("-c" argument). The "%[^:]" conversions have no
maximum field width, so if the address substring before the ':' exceeds
63 bytes, sscanf() writes past the end of the 64-byte saddr/daddr stack
buffers. This overflows the stack, corrupting adjacent stack data such
as the saved return address, and can crash the tool or lead to
out-of-bounds writes controlled by user-supplied input.
Bound both string conversions to the destination buffer size by adding
an explicit maximum field width of 63 (leaving room for the terminating
NUL), so at most 63 bytes are written into each 64-byte buffer:
ret = sscanf(subflow_addrs, "%63[^:]:%d %63[^:]:%d",
saddr, &sport, daddr, &dport);
The subflow address can be passed in argument, so fixing this is helpful
when the tool is manually used.
Reviewed-by: Geliang Tang <geliang@kernel.org>
Signed-off-by: Jiangshan Yi <yijiangshan@kylinos.cn>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260812-net-next-mptcp-misc-feat-7-3-v1-11-1905a818f6cb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In mptcp_connect.c, strchr() returns a pointer to a character within
the input string, which is declared as const char *. Assigning this
return value to a non-const char * discards the const qualifier,
triggering compiler warnings:
make: Entering directory 'tools/testing/selftests/net/mptcp'
CC mptcp_connect
mptcp_connect.c: In function 'parse_cmsg_types':
mptcp_connect.c:1267:22: warning: initialization discards 'const'
qualifier from pointer target type [-Wdiscarded-qualifiers]
1267 | char *next = strchr(type, ',');
| ^~~~~~
mptcp_connect.c: In function 'parse_setsock_options':
mptcp_connect.c:1295:22: warning: initialization discards 'const'
qualifier from pointer target type [-Wdiscarded-qualifiers]
1295 | char *next = strchr(name, ',');
| ^~~~~~
make: Leaving directory 'tools/testing/selftests/net/mptcp'
Fix these warnings by declaring the 'next' variable as const char *,
as it is only used for read-only parsing.
Signed-off-by: Geliang Tang <tanggeliang@kylinos.cn>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260812-net-next-mptcp-misc-feat-7-3-v1-10-1905a818f6cb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Limit the size of each captured packet to 108B (IPv4 only) or 128B (a
mix of v4 and v6): this should drop most of the payload that is
generally not needed when debugging an issue.
8 bytes are left in this payload, to be able to inspect the beginning,
just in case.
Please also note that generally, this payload is usually mostly filled
with 0, except at the end. This reduces the .pcap sizes, and reduce IO
usage, which helps debugging issues.
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260812-net-next-mptcp-misc-feat-7-3-v1-9-1905a818f6cb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add named env-var expectations for each per-event MPTCP_RST_EMPTCP
counter, matching the pattern used by the existing JOIN/RST checks.
Each defaults to 0 and is checked silently on success; a mismatch prints
a check line and fails the test. Counters absent from the running
kernel are skipped silently so older kernels do not false-fail.
The JOIN-related counters (MPJoinSynAckNoMPJoin, MPJoinAckNoMPJoin,
MPJoinAckNoCtx, MPJoinNotEstablished, MPJoinNoIdFound) are checked in
chk_join_nr() on fixed namespaces; the two remaining reset counters
(MD5SigReset, DssReset) stay in chk_rst_nr().
Add a test at the end of signal_address_tests that triggers
MPJoinSynAckNoMPJoin: ns1 signals an address that is already bound on
the client (ns2), where a TCP-only mptcp_connect listener is started.
The client's MP_JOIN routes locally to the TCP listener, which responds
with a plain SYN/ACK without the MP_JOIN option, and the new counter
increments on the client side.
Other per-event counters (MD5SigReset, MPJoinAckNoMPJoin, MPJoinAckNoCtx,
DssReset, MPJoinNotEstablished, MPJoinNoIdFound) are not currently
reachable from mptcp_join.sh; the env-var hooks are in place for future
tests to set expectations explicitly.
Signed-off-by: Shardul Bankar <shardul.b@mpiricsoftware.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260812-net-next-mptcp-misc-feat-7-3-v1-6-1905a818f6cb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
MPTCP_RST_EMPTCP (reset reason 1) is used as a catch-all for several
distinct error conditions across subflow setup, authentication, and
data-path validation. The existing MPRstTx/MPRstRx counters only
track aggregate reset volume, making it difficult to diagnose which
code path is triggering subflow resets in production.
Add per-event MIB counters covering each MPTCP_RST_EMPTCP use site
that is not already covered by an existing counter, named after the
underlying event or condition rather than the reset action:
MD5SigReset MD5SIG enabled on listener (incompatible)
MPJoinSynAckNoMPJoin SYN/ACK missing MP_JOIN option
MPJoinAckNoMPJoin server-side ACK missing MP_JOIN option
(fallback path, MPJoin required)
MPJoinAckNoCtx server-side ACK with no subflow context
MPJoinNoIdFound MP_JOIN with a valid token but no PM local ID
DssReset data mapping invalid (also fires on
MAPPING_NODSS / EMIDDLEBOX path)
MPJoinNotEstablished JOIN attempted on a not-fully-established msk
MPJoinNoIdFound covers the second half of the no-msk MP_JOIN reset:
the existing MPJoinNoTokenFound (MPTCP_MIB_JOINNOTOKEN) only counts the
missing-token case in subflow_token_join_request(), while a JOIN that
carries a valid token but for which the path manager returns no local
id reaches the same MPTCP_RST_EMPTCP in subflow_check_req() uncounted.
The aggregate MPRstTx/MPRstRx counters are unchanged.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/511
Signed-off-by: Shardul Bankar <shardul.b@mpiricsoftware.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260812-net-next-mptcp-misc-feat-7-3-v1-5-1905a818f6cb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MPTCP-level retransmit timers (DATA_FIN retransmissions and the
fallback timeout) used the hard-coded TCP_RTO_MIN / TCP_RTO_MAX
constants, ignoring the tcp_rto_min_us and tcp_rto_max_ms sysctls.
Make them follow the sysctls instead: seed icsk_rto_min / icsk_rto_max
on the MPTCP socket from the per-netns sysctls in __mptcp_init_sock()
-- the msk does not go through tcp_init_sock(), so these fields would
otherwise stay zero -- and read them directly where the constants were
used:
- mptcp_set_datafin_timeout(): both the backoff cap computation and
the resulting timer_ival. The two sysctls are validated
independently, so rto_min > rto_max is a valid configuration; keep
a max_t() guard so ilog2() is never called with 0.
- __mptcp_set_timeout(): the fallback when no subflow timeout is
available.
The icsk fields are read directly instead of using the
tcp_rto_min()/tcp_rto_max() helpers: the MPTCP socket does not perform
routing lookups in these paths, so the rto_min route metric checked by
tcp_rto_min() can never apply here. The TCP_RTO_MIN_US /
TCP_RTO_MAX_MS socket options are not supported by MPTCP setsockopt()
either; this can be revisited if they get supported on MPTCP sockets.
The remaining uses of TCP_RTO_MAX in net/mptcp/ctrl.c (default
add_addr_timeout) and net/mptcp/subflow.c (MP_FAIL timeout) are
intentionally left unchanged: they use the constant as a default
duration, not as an RTO bound on a retransmit timer.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/618
Signed-off-by: Kalpan Jani <kalpan.jani@mpiricsoftware.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260812-net-next-mptcp-misc-feat-7-3-v1-4-1905a818f6cb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
EMAC has never supported changing ring sizes: RX is hardcoded to 9 and
TX is the tiniest ring buffer you can imagine.
Make sure the operation fails early rather than silently succeed and
storing values in bp->configured_{rx,tx}_ring_size that are never read
in the EMAC case.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20260812-macb-context-v9-7-7ddbf5f715e0@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The tieoff descriptor is a RX DMA descriptor ring of size one. It gets
configured onto queues for Wake-on-LAN during system-wide suspend when
hardware does not support disabling individual queues
(MACB_CAPS_QUEUE_DISABLE).
MACB/GEM driver allocates it alongside the main RX ring
inside macb_alloc() at open. Free is done by macb_free() at close.
Change to allocate once at probe and free on probe failure or device
removal. This makes the tieoff descriptor lifetime much longer,
avoiding repeating coherent buffer allocation on each open/close cycle.
Main benefit: we dissociate its lifetime from the main ring's lifetime.
That way there is less work to be doing on resources (re)alloc. This
currently happens on close/open, but will soon also happen on context
swap operations (set_ringparam, change_mtu, set_channels, etc).
Reviewed-by: Nicolai Buchwitz <nb@tipi-net.de>
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Link: https://patch.msgid.link/20260812-macb-context-v9-6-7ddbf5f715e0@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
