The ti-sn65dsi86 MIPI DSI to eDP bridge chip supports arbitrary
remapping of eDP lanes and also polarity inversion. Both of these
features have been described in the device tree bindings for the
device since the beginning but were never implemented in the driver.
Implement both of them.
Part of this change also allows you to (via the same device tree
bindings) specify to use fewer than the max number of DP lanes that
the panel reports. This could be useful if your display supports more
lanes but only a few are hooked up on your board.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200518114656.REPOST.v2.1.Ibc8eeddcee94984a608d6900b46f9ffde4045da4@changeid
The ti-sn65dsi86 MIPI DSI to eDP bridge chip has a dedicated hardware
HPD (Hot Plug Detect) pin on it, but it's mostly useless for eDP
because of excessive debouncing in hardware. Specifically there is no
way to disable the debouncing and for eDP debouncing hurts you because
HPD is just used for knowing when the panel is ready, not for
detecting physical plug events.
Currently the driver in Linux just assumes that nobody has HPD hooked
up. It relies on folks setting the "no-hpd" property in the panel
node to specify that HPD isn't hooked up and then the panel driver
using this to add some worst case delays when turning on the panel.
Apparently it's also useful to specify "no-hpd" in the bridge node so
that the bridge driver can make sure it's doing the right thing
without peeking into the panel [1]. This would be used if anyone ever
found it useful to implement support for the HW HPD pin on the bridge.
Let's add this property to the bindings.
NOTES:
- This is somewhat of a backward-incompatible change. All current
known users of ti-sn65dsi86 didn't have "no-hpd" specified in the
bridge node yet none of them had HPD hooked up. This worked because
the current Linux driver just assumed that HPD was never hooked up.
We could make it less incompatible by saying that for this bridge
it's assumed HPD isn't hooked up _unless_ a property is defined, but
"no-hpd" is much more standard and it's unlikely to matter unless
someone quickly goes and implements HPD in the driver.
- It is sensible to specify "no-hpd" at the bridge chip level and
specify "hpd-gpios" at the panel level. That would mean HPD is
hooked up to some other GPIO in the system, just not the hardware
HPD pin on the bridge chip.
[1] https://lore.kernel.org/r/20200417180819.GE5861@pendragon.ideasonboard.com
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507143354.v5.5.I72892d485088e57378a4748c86bc0f6c2494d807@changeid
The ti-sn65dsi86 MIPI DSI to eDP bridge chip has 4 pins on it that can
be used as GPIOs in a system. Each pin can be configured as input,
output, or a special function for the bridge chip. These are:
- GPIO1: SUSPEND Input
- GPIO2: DSIA VSYNC
- GPIO3: DSIA HSYNC or VSYNC
- GPIO4: PWM
Let's expose these pins as GPIOs. A few notes:
- Access to ti-sn65dsi86 is via i2c so we set "can_sleep".
- These pins can't be configured for IRQ.
- There are no programmable pulls or other fancy features.
- Keeping the bridge chip powered might be expensive. The driver is
setup such that if all used GPIOs are only inputs we'll power the
bridge chip on just long enough to read the GPIO and then power it
off again. Setting a GPIO as output will keep the bridge powered.
- If someone releases a GPIO we'll implicitly switch it to an input so
we no longer need to keep the bridge powered for it.
Because of all of the above limitations we just need to implement a
bare-bones GPIO driver. The device tree bindings already account for
this device being a GPIO controller so we only need the driver changes
for it.
NOTE: Despite the fact that these pins are nominally muxable I don't
believe it makes sense to expose them through the pinctrl interface as
well as the GPIO interface. The special functions are things that the
bridge chip driver itself would care about and it can just configure
the pins as needed.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
[added pdata->gchip.base = -1;]
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507143354.v5.1.Ia50267a5549392af8b37e67092ca653a59c95886@changeid
drivers/gpu/drm/drm_client_modeset.c: In function ‘drm_client_firmware_config’:
./include/linux/bits.h:26:28: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
__builtin_constant_p((l) > (h)), (l) > (h), 0)))
v2: Add a warning for passing connector_count==0 as this will hit an
infinite loop, so document the invalid parameter.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200516212330.13633-2-chris@chris-wilson.co.uk
drm_helper_probe_add_cmdline_mode() prefers using a probed mode matching
a video= argument over calculating our own timings for the user specified
mode using CVT or GTF.
But userspace code which is auto-configuring the mode may want to know that
the user has specified that mode on the kernel commandline so that it can
pick that mode over the mode which is marked as DRM_MODE_TYPE_PREFERRED.
This commit sets the DRM_MODE_TYPE_USERDEF flag on the matching mode, just
as we would do on the user-specified mode when no matching probed mode is
found.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200221173313.510235-2-hdegoede@redhat.com
The R-Car DU driver calls drm_vblank_init via some helper functions in
probe(). From what I checked, most drivers do this as well. I have a
config now where DU always stays in deferred_probe state because of a
missing dependency. This means that every time I rebind another driver
like MMC, the vblank init message is displayed again when the DU driver
is retried. Because the message doesn't really carry a useful
information, I suggest to simply drop it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200513201016.23047-1-wsa+renesas@sang-engineering.com
People use panel-simple when they have panels that are builtin to
their device. In these cases the HPD (Hot Plug Detect) signal isn't
really used for hotplugging devices but instead is used for power
sequencing. Panel timing diagrams (especially for eDP panels) usually
have the HPD signal in them and it acts as an indicator that the panel
is ready for us to talk to it.
Sometimes the HPD signal is hooked up to a normal GPIO on a system.
In this case we need to poll it in the correct place to know that the
panel is ready for us. In some system designs the right place for
this is panel-simple.
When adding this support, we'll account for the case that there might
be a circular dependency between panel-simple and the provider of the
GPIO. The case this was designed for was for the "ti-sn65dsi86"
bridge chip. If HPD is hooked up to one of the GPIOs provided by the
bridge chip then in our probe function we'll always get back
-EPROBE_DEFER. Let's handle this by allowing this GPIO to show up
late if we saw -EPROBE_DEFER during probe. NOTE: since the
gpio_get_optional() is used, if the "hpd-gpios" isn't there our
variable will just be NULL and we won't do anything in prepare().
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200507143354.v5.3.I53fed5b501a31e7a7fa13268ebcdd6b77bd0cadd@changeid
The BOE NV133FHM-N61 is documented in the original commit to be a
13.3" panel, but the size listed in our struct doesn't match.
Specifically:
math.sqrt(30.0 * 30.0 + 18.7 * 18.7) / 2.54 ==> 13.92
Searching around on the Internet shows that the size that was in the
structure was the "Outline Size", not the "Display Area". Let's fix
it.
Also the Internet says that this panel supports 262K colors. That's
6bpp, not 8bpp.
Fixes: b0c664cc80 ("panel: simple: Add BOE NV133FHM-N61")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200508155859.1.I4d29651c0837b4095fb4951253f44036a371732f@changeid
Make an additional note on DRM format modifiers for x and y tiling. These
format modifiers are defined for BDW+ platforms and therefore definition
is not valid for older gens. This is due to address swizzling for tiled
surfaces is no longer used. For newer platforms main memory controller has
a more effective address swizzling algorithm.
v2: Rephrase comment (Daniel)
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200506120827.12250-1-mika.kahola@intel.com
This adds support for TMP5P5 NT35596 1080x1920 video
mode panel that can be found on some Asus Zenfone 2
Laser (Z00T) devices.
This panel seems to only be found in this device
and we have no straightforward way of actually
getting the correct model number, as no schematics
are released publicly.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
[fixed checkpatch warnings]
Link: https://patchwork.freedesktop.org/patch/msgid/20200506210957.344590-2-konradybcio@gmail.com
