If no PHY device is found (e.g., for LAN7801 in fixed-link mode),
lan78xx_phy_init() may proceed to dereference a NULL phydev pointer,
leading to a crash.
Update the logic to perform MAC configuration first, then check for the presence
of a PHY. For the fixed-link case, set up the fixed link and return early,
bypassing any code that assumes a valid phydev pointer.
It is safe to move lan78xx_mac_prepare_for_phy() earlier because this function
only uses information from dev->interface, which is configured by
lan78xx_get_phy() beforehand. The function does not access phydev or any data
set up by later steps.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: e110bc8258 ("net: usb: lan78xx: Convert to PHYLINK for improved PHY and MAC management")
Link: https://patch.msgid.link/20250626103731.3986545-1-o.rempel@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Some counters in enetc_port_counters are 32-bit registers, and some are
64-bit registers. But in the current driver, they are all read through
enetc_port_rd(), which can only read a 32-bit value. Therefore, separate
64-bit counters (enetc_pm_counters) from enetc_port_counters and use
enetc_port_rd64() to read the 64-bit statistics.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250627021108.3359642-3-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The statistics of the ring are all unsigned int type, so the statistics
will overflow quickly under heavy traffic. In addition, the statistics
of struct net_device_stats are obtained from struct enetc_ring_stats,
but the statistics of net_device_stats are unsigned long type. So it is
better to keep the statistics types consistent in these two structures.
Considering these two factors, and the fact that both LS1028A and i.MX95
are arm64 architecture, the statistics of enetc_ring_stats are changed
to unsigned long type. Note that unsigned int and unsigned long are the
same thing on some systems, and on such systems there is no overflow
advantage of one over the other.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250627021108.3359642-2-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the current implementation, IP coalescing is always enabled and
cannot be disabled.
As setting maximum frames to 0 or 1, or setting delay to zero implies
immediate delivery of single packets/IRQs, disable coalescing in
hardware in these cases.
This also guarantees that coalescing is never enabled with ICFT or ICTT
set to zero, a configuration that could lead to unpredictable behaviour
according to i.MX8MP reference manual.
Signed-off-by: Jonas Rebmann <jre@pengutronix.de>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Link: https://patch.msgid.link/20250626-fec_deactivate_coalescing-v2-1-0b217f2e80da@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel says:
====================
Add support for externally validated neighbor entries
Patch #1 adds a new neighbor flag ("extern_valid") that prevents the
kernel from invalidating or removing a neighbor entry, while allowing
the kernel to notify user space when the entry becomes reachable. See
motivation and implementation details in the commit message.
Patch #2 adds a selftest.
v1: https://lore.kernel.org/20250611141551.462569-1-idosch@nvidia.com
====================
Link: https://patch.msgid.link/20250626073111.244534-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add test cases for externally validated neighbor entries, testing both
IPv4 and IPv6. Name the file "test_neigh.sh" so that it could be
possibly extended in the future with more neighbor test cases.
Example output:
# ./test_neigh.sh
TEST: IPv4 "extern_valid" flag: Add entry [ OK ]
TEST: IPv4 "extern_valid" flag: Add with an invalid state [ OK ]
TEST: IPv4 "extern_valid" flag: Add with "use" flag [ OK ]
TEST: IPv4 "extern_valid" flag: Replace entry [ OK ]
TEST: IPv4 "extern_valid" flag: Replace entry with "managed" flag [ OK ]
TEST: IPv4 "extern_valid" flag: Replace with an invalid state [ OK ]
TEST: IPv4 "extern_valid" flag: Interface down [ OK ]
TEST: IPv4 "extern_valid" flag: Carrier down [ OK ]
TEST: IPv4 "extern_valid" flag: Transition to "reachable" state [ OK ]
TEST: IPv4 "extern_valid" flag: Transition back to "stale" state [ OK ]
TEST: IPv4 "extern_valid" flag: Forced garbage collection [ OK ]
TEST: IPv4 "extern_valid" flag: Periodic garbage collection [ OK ]
TEST: IPv6 "extern_valid" flag: Add entry [ OK ]
TEST: IPv6 "extern_valid" flag: Add with an invalid state [ OK ]
TEST: IPv6 "extern_valid" flag: Add with "use" flag [ OK ]
TEST: IPv6 "extern_valid" flag: Replace entry [ OK ]
TEST: IPv6 "extern_valid" flag: Replace entry with "managed" flag [ OK ]
TEST: IPv6 "extern_valid" flag: Replace with an invalid state [ OK ]
TEST: IPv6 "extern_valid" flag: Interface down [ OK ]
TEST: IPv6 "extern_valid" flag: Carrier down [ OK ]
TEST: IPv6 "extern_valid" flag: Transition to "reachable" state [ OK ]
TEST: IPv6 "extern_valid" flag: Transition back to "stale" state [ OK ]
TEST: IPv6 "extern_valid" flag: Forced garbage collection [ OK ]
TEST: IPv6 "extern_valid" flag: Periodic garbage collection [ OK ]
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://patch.msgid.link/20250626073111.244534-3-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tl;dr
=====
Add a new neighbor flag ("extern_valid") that can be used to indicate to
the kernel that a neighbor entry was learned and determined to be valid
externally. The kernel will not try to remove or invalidate such an
entry, leaving these decisions to the user space control plane. This is
needed for EVPN multi-homing where a neighbor entry for a multi-homed
host needs to be synced across all the VTEPs among which the host is
multi-homed.
Background
==========
In a typical EVPN multi-homing setup each host is multi-homed using a
set of links called ES (Ethernet Segment, i.e., LAG) to multiple leaf
switches (VTEPs). VTEPs that are connected to the same ES are called ES
peers.
When a neighbor entry is learned on a VTEP, it is distributed to both ES
peers and remote VTEPs using EVPN MAC/IP advertisement routes. ES peers
use the neighbor entry when routing traffic towards the multi-homed host
and remote VTEPs use it for ARP/NS suppression.
Motivation
==========
If the ES link between a host and the VTEP on which the neighbor entry
was locally learned goes down, the EVPN MAC/IP advertisement route will
be withdrawn and the neighbor entries will be removed from both ES peers
and remote VTEPs. Routing towards the multi-homed host and ARP/NS
suppression can fail until another ES peer locally learns the neighbor
entry and distributes it via an EVPN MAC/IP advertisement route.
"draft-rbickhart-evpn-ip-mac-proxy-adv-03" [1] suggests avoiding these
intermittent failures by having the ES peers install the neighbor
entries as before, but also injecting EVPN MAC/IP advertisement routes
with a proxy indication. When the previously mentioned ES link goes down
and the original EVPN MAC/IP advertisement route is withdrawn, the ES
peers will not withdraw their neighbor entries, but instead start aging
timers for the proxy indication.
If an ES peer locally learns the neighbor entry (i.e., it becomes
"reachable"), it will restart its aging timer for the entry and emit an
EVPN MAC/IP advertisement route without a proxy indication. An ES peer
will stop its aging timer for the proxy indication if it observes the
removal of the proxy indication from at least one of the ES peers
advertising the entry.
In the event that the aging timer for the proxy indication expired, an
ES peer will withdraw its EVPN MAC/IP advertisement route. If the timer
expired on all ES peers and they all withdrew their proxy
advertisements, the neighbor entry will be completely removed from the
EVPN fabric.
Implementation
==============
In the above scheme, when the control plane (e.g., FRR) advertises a
neighbor entry with a proxy indication, it expects the corresponding
entry in the data plane (i.e., the kernel) to remain valid and not be
removed due to garbage collection or loss of carrier. The control plane
also expects the kernel to notify it if the entry was learned locally
(i.e., became "reachable") so that it will remove the proxy indication
from the EVPN MAC/IP advertisement route. That is why these entries
cannot be programmed with dummy states such as "permanent" or "noarp".
Instead, add a new neighbor flag ("extern_valid") which indicates that
the entry was learned and determined to be valid externally and should
not be removed or invalidated by the kernel. The kernel can probe the
entry and notify user space when it becomes "reachable" (it is initially
installed as "stale"). However, if the kernel does not receive a
confirmation, have it return the entry to the "stale" state instead of
the "failed" state.
In other words, an entry marked with the "extern_valid" flag behaves
like any other dynamically learned entry other than the fact that the
kernel cannot remove or invalidate it.
One can argue that the "extern_valid" flag should not prevent garbage
collection and that instead a neighbor entry should be programmed with
both the "extern_valid" and "extern_learn" flags. There are two reasons
for not doing that:
1. Unclear why a control plane would like to program an entry that the
kernel cannot invalidate but can completely remove.
2. The "extern_learn" flag is used by FRR for neighbor entries learned
on remote VTEPs (for ARP/NS suppression) whereas here we are
concerned with local entries. This distinction is currently irrelevant
for the kernel, but might be relevant in the future.
Given that the flag only makes sense when the neighbor has a valid
state, reject attempts to add a neighbor with an invalid state and with
this flag set. For example:
# ip neigh add 192.0.2.1 nud none dev br0.10 extern_valid
Error: Cannot create externally validated neighbor with an invalid state.
# ip neigh add 192.0.2.1 lladdr 00:11:22:33:44:55 nud stale dev br0.10 extern_valid
# ip neigh replace 192.0.2.1 nud failed dev br0.10 extern_valid
Error: Cannot mark neighbor as externally validated with an invalid state.
The above means that a neighbor cannot be created with the
"extern_valid" flag and flags such as "use" or "managed" as they result
in a neighbor being created with an invalid state ("none") and
immediately getting probed:
# ip neigh add 192.0.2.1 lladdr 00:11:22:33:44:55 nud stale dev br0.10 extern_valid use
Error: Cannot create externally validated neighbor with an invalid state.
However, these flags can be used together with "extern_valid" after the
neighbor was created with a valid state:
# ip neigh add 192.0.2.1 lladdr 00:11:22:33:44:55 nud stale dev br0.10 extern_valid
# ip neigh replace 192.0.2.1 lladdr 00:11:22:33:44:55 nud stale dev br0.10 extern_valid use
One consequence of preventing the kernel from invalidating a neighbor
entry is that by default it will only try to determine reachability
using unicast probes. This can be changed using the "mcast_resolicit"
sysctl:
# sysctl net.ipv4.neigh.br0/10.mcast_resolicit
0
# tcpdump -nn -e -i br0.10 -Q out arp &
# ip neigh replace 192.0.2.1 lladdr 00:11:22:33:44:55 nud stale dev br0.10 extern_valid use
62:50:1d:11:93:6f > 00:11:22:33:44:55, ethertype ARP (0x0806), length 42: Request who-has 192.0.2.1 tell 192.0.2.2, length 28
62:50:1d:11:93:6f > 00:11:22:33:44:55, ethertype ARP (0x0806), length 42: Request who-has 192.0.2.1 tell 192.0.2.2, length 28
62:50:1d:11:93:6f > 00:11:22:33:44:55, ethertype ARP (0x0806), length 42: Request who-has 192.0.2.1 tell 192.0.2.2, length 28
# sysctl -wq net.ipv4.neigh.br0/10.mcast_resolicit=3
# ip neigh replace 192.0.2.1 lladdr 00:11:22:33:44:55 nud stale dev br0.10 extern_valid use
62:50:1d:11:93:6f > 00:11:22:33:44:55, ethertype ARP (0x0806), length 42: Request who-has 192.0.2.1 tell 192.0.2.2, length 28
62:50:1d:11:93:6f > 00:11:22:33:44:55, ethertype ARP (0x0806), length 42: Request who-has 192.0.2.1 tell 192.0.2.2, length 28
62:50:1d:11:93:6f > 00:11:22:33:44:55, ethertype ARP (0x0806), length 42: Request who-has 192.0.2.1 tell 192.0.2.2, length 28
62:50:1d:11:93:6f > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.0.2.1 tell 192.0.2.2, length 28
62:50:1d:11:93:6f > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.0.2.1 tell 192.0.2.2, length 28
62:50:1d:11:93:6f > ff:ff:ff:ff:ff:ff, ethertype ARP (0x0806), length 42: Request who-has 192.0.2.1 tell 192.0.2.2, length 28
iproute2 patches can be found here [2].
[1] https://datatracker.ietf.org/doc/html/draft-rbickhart-evpn-ip-mac-proxy-adv-03
[2] https://github.com/idosch/iproute2/tree/submit/extern_valid_v1
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://patch.msgid.link/20250626073111.244534-2-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
net: ethtool: consistently take rss_lock for all rxfh ops
I'd like to bring RXFH and RXFHINDIR ioctls under a single set of
Netlink ops. It appears that while core takes the ethtool->rss_lock
around some of the RXFHINDIR ops, drivers (sfc) take it internally
for the RXFH.
Consistently take the lock around all ops and accesses to the XArray
within the core. This should hopefully make the rss_lock a lot less
confusing.
====================
Link: https://patch.msgid.link/20250626202848.104457-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We already call get_rxfh under the rss_lock when we read back
context state after changes. Let's be consistent and always
hold the lock. The existing callers are all under rtnl_lock
so this should make no difference in practice, but it makes
the locking rules far less confusing IMHO. Any RSS callback
and any access to the RSS XArray should hold the lock.
Link: https://patch.msgid.link/20250626202848.104457-4-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Netlink code will want to perform the RSS_SET operation atomically
under the rss_lock. sfc wants to hold the rss_lock in rxfh_fields_get,
which makes that difficult. Lets move the locking up to the core
so that for all driver-facing callbacks rss_lock is taken consistently
by the core.
Link: https://patch.msgid.link/20250626202848.104457-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Always take the rss_lock in ethtool_set_rxfh(). We will want to
make a similar change in ethtool_set_rxfh_fields() and some
drivers lock that callback regardless of rss context ID being set.
Having some callbacks locked unconditionally and some only if
context ID is set would be very confusing.
ethtool handling is under rtnl_lock, so rss_lock is very unlikely
to ever be congested.
Link: https://patch.msgid.link/20250626202848.104457-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently when xdp_rxq_info_reg_mem_model() fails in the XSK path, the
error handling incorrectly jumps to err_destroy_page_pool. While this
may not cause errors, we should make it jump to the correct location.
Signed-off-by: Fushuai Wang <wangfushuai@baidu.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@linux.dev>
Acked-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The error code was intended to be -EINVAL here, but it was accidentally
changed to returning success. Set the error code.
Fixes: e53ee4acb2 ("octeontx2-af: CN20k basic mbox operations and structures")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hariprasad Kelam says:
====================
Octeontx2-pf: extend link modes support
This series of patches adds multi advertise mode support along with
other improvements in link mode management code flow.
Patch1: Currently all SGMII modes 10/100/1000baseT are mapped with
single firmware mode. This patch updates these link modes
with corresponding firmware modes.
Patch2: Due to limitation in current kernel <-> firmware communication,
link modes are divided into multiple groups, and identified
with their group index.
Patch3: Adds support for multi advertise mode.
====================
Link: https://patch.msgid.link/20250625092107.9746-1-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current implementation considers only first advertise
mode and passes the same to firmware to process.
This patch extends code such that user can advertise
multiple modes on the given interface.
Below are high level changes:
1. Remove unnecessary speed/duplex/autoneg validation as its
already verified as part of "set_link_ksettings"
2. Since scratch csr framework designed to support single mode at a time,
use "shared firmware data" for multi mode support.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20250625092107.9746-4-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kernel and firmware communicates via scratch register which is
64 bit in size.
[MODE_ID PORT AUTONEG DUPLEX SPEED CMD_ID OWNERSHIP ]
63-22 21-14 13 12 11-8 7-2 1-0
The existing MODE_ID bitmap can only support up to 42 modes.
To resolve the issue, the unused port field is modified as below
uint64_t reserved2:6;
uint64_t mode_group_idx:2;
'mode_group_idx' categorize the mode ID range to accommodate more modes.
To specify mode ID range of 0 - 41, this field will be 0.
To specify mode ID range of 42 - 83, this field will be 1.
mode ID will be still mentioned as 1 << (0 - 41). But the mode_group_idx
decides the actual mode range
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20250625092107.9746-3-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current implementation maps ethtool link modes 10baseT/100baseT/1000baseT
to single firmware mode SGMII. This create a problem for end users who want
to advertise only one speed among them.
This patch addresses the issue by mapping each ethtool link mode
to a corresponding firmware mode also updates new modes supported
by firmware.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Link: https://patch.msgid.link/20250625092107.9746-2-hkelam@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Arkadiusz Kubalewski says:
====================
dpll: add Reference SYNC feature
The device may support the Reference SYNC feature, which allows the
combination of two inputs into a input pair. In this configuration,
clock signals from both inputs are used to synchronize the DPLL device.
The higher frequency signal is utilized for the loop bandwidth of the DPLL,
while the lower frequency signal is used to syntonize the output signal of
the DPLL device. This feature enables the provision of a high-quality loop
bandwidth signal from an external source.
A capable input provides a list of inputs that can be bound with to create
Reference SYNC. To control this feature, the user must request a
desired state for a target pin: use ``DPLL_PIN_STATE_CONNECTED`` to
enable or ``DPLL_PIN_STATE_DISCONNECTED`` to disable the feature. An input
pin can be bound to only one other pin at any given time.
Verify pins bind state/capabilities:
$ ./tools/net/ynl/pyynl/cli.py \
--spec Documentation/netlink/specs/dpll.yaml \
--do pin-get \
--json '{"id":0}'
{'board-label': 'CVL-SDP22',
'id': 0,
[...]
'reference-sync': [{'id': 1, 'state': 'disconnected'}],
[...]}
Bind the pins by setting connected state between them:
$ ./tools/net/ynl/pyynl/cli.py \
--spec Documentation/netlink/specs/dpll.yaml \
--do pin-set \
--json '{"id":0, "reference-sync":{"id":1, "state":"connected"}}'
Verify pins bind state:
$ ./tools/net/ynl/pyynl/cli.py \
--spec Documentation/netlink/specs/dpll.yaml \
--do pin-get \
--json '{"id":0}'
{'board-label': 'CVL-SDP22',
'id': 0,
[...]
'reference-sync': [{'id': 1, 'state': 'connected'}],
[...]}
Unbind the pins by setting disconnected state between them:
$ ./tools/net/ynl/pyynl/cli.py \
--spec Documentation/netlink/specs/dpll.yaml \
--do pin-set \
--json '{"id":0, "reference-sync":{"id":1, "state":"disconnected"}}'
====================
Link: https://patch.msgid.link/20250626135219.1769350-1-arkadiusz.kubalewski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
ice: remaining TSPLL cleanups
These are the remaining patches from the "ice: Separate TSPLL from PTP
and cleanup" series [1] with control flow macros removed. What remains
are cleanups and some minor improvements.
[1] https://lore.kernel.org/netdev/20250618174231.3100231-1-anthony.l.nguyen@intel.com/
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: default to TIME_REF instead of TXCO on E825-C
ice: move TSPLL init calls to ice_ptp.c
ice: fall back to TCXO on TSPLL lock fail
ice: wait before enabling TSPLL
ice: add multiple TSPLL helpers
ice: use bitfields instead of unions for CGU regs
ice: read TSPLL registers again before reporting status
ice: clear time_sync_en field for E825-C during reprogramming
====================
Link: https://patch.msgid.link/20250626162921.1173068-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Rx rings are filled with Rx buffers. Which are supposed to fit
packet headers (or MTU if HW-GRO is disabled). The aggregation buffers
are filled with "device pages". Adjust the sizes of the page pool
recycling ring appropriately, based on ratio of the size of the
buffer on given ring vs system page size. Otherwise on a system
with 64kB pages we end up with >700MB of memory sitting in every
single page pool cache.
Correct the size calculation for the head_pool. Since the buffers
there are always small I'm pretty sure I meant to cap the size
at 1k, rather than make it the lowest possible size. With 64k pages
1k cache with a 1k ring is 64x larger than we need.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://patch.msgid.link/20250626165441.4125047-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Test DSACK behavior with non contiguous ranges.
Without prior fix (tcp: fix tcp_ofo_queue() to avoid including
too much DUP SACK range) this would fail with:
tcp_dsack_mult.pkt:37: error handling packet: bad value outbound TCP option 5
script packet: 0.100682 . 1:1(0) ack 6001 <nop,nop,sack 1001:3001 7001:8001>
actual packet: 0.100679 . 1:1(0) ack 6001 win 1097 <nop,nop,sack 1001:6001 7001:8001>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: xin.guo <guoxin0309@gmail.com>
Link: https://patch.msgid.link/20250626123420.1933835-3-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the new coming segment covers more than one skbs in the ofo queue,
and which seq is equal to rcv_nxt, then the sequence range
that is duplicated will be sent as DUP SACK, the detail as below,
in step6, the {501,2001} range is clearly including too much
DUP SACK range, in violation of RFC 2883 rules.
1. client > server: Flags [.], seq 501:1001, ack 1325288529, win 20000, length 500
2. server > client: Flags [.], ack 1, [nop,nop,sack 1 {501:1001}], length 0
3. client > server: Flags [.], seq 1501:2001, ack 1325288529, win 20000, length 500
4. server > client: Flags [.], ack 1, [nop,nop,sack 2 {1501:2001} {501:1001}], length 0
5. client > server: Flags [.], seq 1:2001, ack 1325288529, win 20000, length 2000
6. server > client: Flags [.], ack 2001, [nop,nop,sack 1 {501:2001}], length 0
After this fix, the final ACK is as below:
6. server > client: Flags [.], ack 2001, options [nop,nop,sack 1 {501:1001}], length 0
[edumazet] added a new packetdrill test in the following patch.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: xin.guo <guoxin0309@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250626123420.1933835-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Linus Walleij says:
====================
net: dsa: ks8995: Fix up bindings
After looking at the datasheets for KS8995 I realized this is
a DSA switch and need to have DT bindings as such and be implemented
as such.
This series just fixes up the bindings and the offending device tree.
The existing kernel driver which is in drivers/net/phy/spi_ks8995.c
does not implement DSA. It can be forgiven for this because it was
merged in 2011 and the DSA framework was not widely established
back then. It continues to probe fine but needs to be rewritten
to use the special DSA tag and moved to drivers/net/dsa as time
permits. (I hope I can do this.)
It's fine for the networking tree to merge both patches, I maintain
ixp4xx as well. But I can also carry the second patch through the
SoC tree if so desired.
v1: https://lore.kernel.org/20250624-ks8995-dsa-bindings-v1-0-71a8b4f63315@linaro.org
====================
Link: https://patch.msgid.link/20250625-ks8995-dsa-bindings-v2-0-ce71dce9be0b@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix up the KS8995 switch and PHYs the way that is most likely:
- Phy 1-4 is certainly the PHYs of the KS8995 (mask 0x1e in
the outoftree code masks PHYs 1,2,3,4).
- Phy 5 is the MII-P5 separate WAN phy of the KS8995 directly
connected to EthC.
- The EthB MII is probably connected as CPU interface to the
KS8995.
Properly integrate the KS8995 switch using the new bindings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250625-ks8995-dsa-bindings-v2-2-ce71dce9be0b@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After studying the datasheets for some of the KS8995 variants
it becomes pretty obvious that this is a straight-forward
and simple MII DSA switch with one port in (CPU) and four outgoing
ports, and it even supports custom tags by setting a bit in
a special register, and elaborate VLAN handling as all DSA
switches do.
What is a bit odd with KS8995 is that it uses an extra MII-P5
port to access one of the PHYs separately, on the side of the
switch fabric, such as when using a WAN port separately from
a LAN switch in a home router.
Rewrite the terse bindings to YAML, and move to the proper
subdirectory. Include a verbose example to make things clear.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Link: https://patch.msgid.link/20250625-ks8995-dsa-bindings-v2-1-ce71dce9be0b@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paul Geurts says:
====================
NFC: trf7970a: Add option to reduce antenna gain
The TRF7970a device is sensitive to RF disturbances, which can make it
hard to pass some EMC immunity tests. By reducing the RX antenna gain,
the device becomes less sensitive to EMC disturbances, as a trade-off
against antenna performance.
====================
Link: https://patch.msgid.link/20250626141242.3749958-1-paul.geurts@prodrive-technologies.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TRF7970a device is sensitive to RF disturbances, which can make it
hard to pass some EMC immunity tests. By reducing the RX antenna gain,
the device becomes less sensitive to EMC disturbances, as a trade-off
against antenna performance.
Add a device tree option to select RX gain reduction to improve EMC
performance.
Selecting a communication standard in the ISO control register resets
the RX antenna gain settings. Therefore set the RX gain reduction
everytime the ISO control register changes, when the option is used.
Signed-off-by: Paul Geurts <paul.geurts@prodrive-technologies.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250626141242.3749958-3-paul.geurts@prodrive-technologies.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Merge a fix from Jeff from a stable commit ID:
* ref_tracker: do xarray and workqueue job initializations earlier
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
