Add support for TPS65219 PMICs GPIO interface.
3 GPIO pins:
- GPIO0 only is IO but input mode reserved for MULTI_DEVICE_ENABLE usage.
- GPIO1 and GPIO2 are Output only and referred as GPO1 and GPO2 in spec.
GPIO0 is statically configured as input or output prior to Linux boot.
it is used for MULTI_DEVICE_ENABLE function.
This setting is statically configured by NVM.
GPIO0 can't be used as a generic GPIO (specification Table 8-34).
It's either a GPO when MULTI_DEVICE_EN=0 or a GPI when MULTI_DEVICE_EN=1.
Datasheet describes specific usage for non standard GPIO.
Datasheet: https://www.ti.com/lit/ds/symlink/tps65219.pdf
Co-developed-by: Jonathan Cormier <jcormier@criticallink.com>
Signed-off-by: Jonathan Cormier <jcormier@criticallink.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jerome Neanne <jneanne@baylibre.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Make the struct irq_chip const and flag it as IRQCHIP_IMMUTABLE,
call gpiochip_disable_irq() in the .irq_mask() callback and
gpiochip_enable_irq() in the .irq_unmask() callback to fix
"gpio gpiochip1: (zynqmp_gpio): not an immutable chip" warning.
Signed-off-by: Manikanta Guntupalli <manikanta.guntupalli@amd.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This patch fixes the following sprse warnings:
drivers/gpio/gpio-davinci.c:695:1: sparse: warning: symbol 'davinci_gpio_dev_pm_ops' was not declared. Should it be static?
No functional change intended.
Signed-off-by: Min-Hua Chen <minhuadotchen@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Since the legacy exporting is gone with 2f804aca48 ("gpiolib:
Kill unused GPIOF_EXPORT and Co") there is no need to unexport
GPIO on freeing. Remove that call.
Note, the other users of this functionality do that explicitly,
except one SH and one OMAP boardfile which don't free GPIO anyways,
so it is safe to drop the call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This driver implements a GPIO enable/disable delay. It supports a list
of GPIO outputs, which ramp-up/ramp-down delay can be specified at
consumer location.
The main purpose is to address external, passive delays upon line
voltage changes.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Now that the of_gpiochip_add() doesn't use valid mask, we may
unify GPIO valid mask allocation and initialization. With this
it makes a symmetry to the similar which we done for IRQ chip.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This removes all usage of global GPIO numbers from
arch/arm/mach-omap[12].
The patches have been reviewed and tested by everyone
who showed interest which was one person that tested
on OSK1 and Nokia 770, and we smoked out the bugs and
also addressed all review comments.
Any remaining problems can certainly be fixed in-tree.
This change checks if we have the necessary permission to
access the GPIO. For devices that have support for virtualisation
we need to check both the TEGRA186_GPIO_VM_REG and the
TEGRA186_GPIO_SCR_REG registers. For device that do not have
virtualisation support for GPIOs we only need to check the
TEGRA186_GPIO_SCR_REG register.
Signed-off-by: Manish Bhardwaj <mbhardwaj@nvidia.com>
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
The TUSB6010 (MUSB) device is picking up some GPIO lines
hardcoded by number and passing on to the TUSB6010 device
when registering it.
Instead of nasty workarounds, provide a GPIO descriptor
table and then make the TUSB6010 MUSB glue driver pick up
the GPIO lines directly, convert it to an IRQ and pass down
to the MUSB driver. OMAP2 is the only system using the
TUSB6010.
Stash the GPIO descriptors in the glue layer and use
then to power up and down the TUSB6010 on-demand, instead
of using boardfile callbacks.
Since the OMAP2 boards are the only boards using the
.set_power() and .board_set_power() callbacks, we can
just delete them as the power is now handled directly
in the TUSB6010 glue code.
Cc: Bin Liu <b-liu@ti.com>
Cc: linux-usb@vger.kernel.org
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OMAP2 platform data quirk is using the global GPIO numberspace
to obtain two WLAN GPIOs to drive power and xcvr reset GPIO
lines during start-up.
Rewrite the quirk to use a GPIO descriptor table so we avoid using
global GPIO numbers.
This gets rid of the final dependency on the legacy <linux/gpio.h>
header from the OMAP2/3 platforms.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the USB hub GPIO reset line handling in the
OMAP2 pdata quirks over to using GPIO descriptors to avoid using
the global GPIO numberspace.
Since the GPIOs are exported and assumedly used by some kind
of userspace we cannot simply use hogs in the device tree.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TWL4030 GPIO driver has a custom platform data .set_up()
callback to call back into the platform and do misc stuff such
as hog and export a GPIO for WLAN PWR on a specific OMAP3 board.
Avoid all the kludgery in the platform data and the boardfile
and just put the quirks right into the driver. Make it
conditional on OMAP3.
I think the exported GPIO is used by some kind of userspace
so ordinary DTS hogs will probably not work.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After fixing all the offending users referencing the global GPIO
numberspace in OMAP1, a few sites still remain including the
legacy <linus/gpio.h> header for no reason.
Delete the last remaining users, and OMAP1 is free from legacy
GPIO dependencies.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The code in serial.c looks up GPIOs corresponding to a line
on the UART when muxed in as GPIO to use this as a wakeup
on serial activity for OMAP1.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, set as input and convert to IRQ numbers,
then set these to wakeup IRQs. This is ugly but should work.
This is only needed on the OSK1 and Nokia 770 devices that
use the OMAP16xx.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The platform devices on the Nokia 770 is using some
board-specific IRQs that get statically assigned to platform
devices in the boardfile.
This does not work with dynamic IRQ chip bases.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, convert to IRQ numbers and pass as resources
to the devices. This is ugly but should work.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A recent change to the OMAP driver making it use a dynamic GPIO
base created problems with some old OMAP1 board files, among
them Nokia 770, SX1 and also the OMAP2 Nokia n8x0.
Fix up all instances of GPIOs being used for the MMC driver
by pushing the handling of power, slot selection and MMC
"cover" into the driver as optional GPIOs.
This is maybe not the most perfect solution as the MMC
framework have some central handlers for some of the
stuff, but it at least makes the situtation better and
solves the immediate issue.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Nokia 770 is using GPIOs from the global numberspace on the
CBUS node to pass down to the LCD controller. This regresses when we
let the OMAP GPIO driver use dynamic GPIO base.
The Nokia 770 now has dynamic allocation of IRQ numbers, so this
needs to be fixed for it to work.
As this is the only user of LCD MIPID we can easily augment the
driver to use a GPIO descriptor instead and resolve the issue.
The platform data .shutdown() callback wasn't even used in the
code, but we encode a shutdown asserting RESET in the remove()
callback for completeness sake.
The CBUS also has the ADS7846 touchscreen attached.
Populate the devices on the Nokia 770 CBUS I2C using software
nodes instead of platform data quirks. This includes the LCD
and the ADS7846 touchscreen so the conversion just brings the LCD
along with it as software nodes is an all-or-nothing design
pattern.
The ADS7846 has some limited support for using GPIO descriptors,
let's convert it over completely to using device properties and then
fix all remaining boardfile users to provide all platform data using
software nodes.
Dump the of includes and of_match_ptr() in the ADS7846 driver as part
of the job.
Since we have to move ADS7846 over to obtaining the GPIOs it is
using exclusively from descriptors, we provide descriptor tables
for the two remaining in-kernel boardfiles using ADS7846:
- PXA Spitz
- MIPS Alchemy DB1000 development board
It was too hard for me to include software node conversion of
these two remaining users at this time: the spitz is using a
hscync callback in the platform data that would require further
GPIO descriptor conversion of the Spitz, and moving the hsync
callback down into the driver: it will just become too big of
a job, but it can be done separately.
The MIPS Alchemy DB1000 is simply something I cannot test, so take
the easier approach of just providing some GPIO descriptors in
this case as I don't want the patch to grow too intrusive.
As we see that several device trees have incorrect polarity flags
and just expect to bypass the gpiolib polarity handling, fix up
all device trees too, in a separate patch.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears this happens because the OMAP driver now
allocates GPIO numbers dynamically, so all that is
references by number is a bit up in the air.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, convert to IRQ numbers and pass as resources
to the devices. This is ugly but should work.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears this happens because the OMAP driver now
allocates GPIO numbers dynamically, so all that is
references by number is a bit up in the air.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, convert to IRQ numbers and pass as resources
to the devices. This is ugly but should work.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AMS Delta board uses GPIO descriptors exclusively and
does not have any dependencies on the legacy <linux/gpio.h>
header, so just drop it.
Acked-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Aaro reports problems on the OSK1 board after we altered
the dynamic base for GPIO allocations.
It appears this happens because the OMAP driver now
allocates GPIO numbers dynamically, so all that is
references by number is a bit up in the air.
Let's bite the bullet and try to just move the gpio_chip
in the tps65010 MFD driver over to using dynamic allocations.
Alter everything in the OSK1 board file to use a GPIO
descriptor table and lookups.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, convert to IRQ numbers and pass as resources
to the devices. This is ugly but should work.
The .setup() callback for tps65010 was used for some GPIO
hogging, but since the OSK1 is the only user in the entire
kernel we can alter the signatures to something that
is helpful and make a clean transition.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: andy.shevchenko@gmail.com
Cc: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Utilize a temporary variable to calculate number of ctx from ngpio
inside ->probe() implementation.
While at it, include math.h for using DIV_ROUND_UP().
Signed-off-by: Raag Jadav <raag.jadav@intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
After commit b8a1a4cd5a ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.
Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
sa1100_init_gpio() is declared in a machine specific header so it
can be called from platform code, but the definition is in the device
driver, which causes a warning:
drivers/gpio/gpio-sa1100.c:310:13: error: no previous prototype for 'sa1100_init_gpio' [-Werror=missing-prototypes]
It's already possible to include mach/generic.h from drivers, so add
this one here as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use devm version of gpiochip_add() function to handle removal for us.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use devm version of gpiochip add function to handle removal for us.
While here update copyright and module author.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Use devm version of gpiochip add function to handle removal for us.
While here update copyright and module author.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This rewrites the STMPE GPIO bindings to a YAML schema.
We add the properties that are used in the widely used
STMPE GPIO device nodes found in the wild, most notably
interrupt support, so interrupt-cells and
interrupt-controller is now part of the bindings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
This is a generic binding for simple MMIO GPIO controllers. Although we
have a single driver for these controllers, they were previously spread
over several files. Consolidate them. The register descriptions are
adapted from the comments in the source. There is no set order for the
registers, and some registers may be omitted. Because of this, reg-names
is mandatory, and no order is specified.
Rename brcm,bcm6345-gpio to brcm,bcm63xx-gpio to reflect that bcm6345
has moved.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Convert platform_get_resource(),devm_ioremap_resource() to a single
call to devm_platform_ioremap_resource(), as this is exactly what this
function does.
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Drop kerneldoc annotation from regular comment to fix:
gpio-davinci.c:716: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Pull perf tool updates from Arnaldo Carvalho de Melo:
"Third version of perf tool updates, with the build problems with with
using a 'vmlinux.h' generated from the main build fixed, and the bpf
skeleton build disabled by default.
Build:
- Require libtraceevent to build, one can disable it using
NO_LIBTRACEEVENT=1.
It is required for tools like 'perf sched', 'perf kvm', 'perf
trace', etc.
libtraceevent is available in most distros so installing
'libtraceevent-devel' should be a one-time event to continue
building perf as usual.
Using NO_LIBTRACEEVENT=1 produces tooling that is functional and
sufficient for lots of users not interested in those libtraceevent
dependent features.
- Allow Python support in 'perf script' when libtraceevent isn't
linked, as not all features requires it, for instance Intel PT does
not use tracepoints.
- Error if the python interpreter needed for jevents to work isn't
available and NO_JEVENTS=1 isn't set, preventing a build without
support for JSON vendor events, which is a rare but possible
condition. The two check error messages:
$(error ERROR: No python interpreter needed for jevents generation. Install python or build with NO_JEVENTS=1.)
$(error ERROR: Python interpreter needed for jevents generation too old (older than 3.6). Install a newer python or build with NO_JEVENTS=1.)
- Make libbpf 1.0 the minimum required when building with out of
tree, distro provided libbpf.
- Use libsdtc++'s and LLVM's libcxx's __cxa_demangle, a portable C++
demangler, add 'perf test' entry for it.
- Make binutils libraries opt in, as distros disable building with it
due to licensing, they were used for C++ demangling, for instance.
- Switch libpfm4 to opt-out rather than opt-in, if libpfm-devel (or
equivalent) isn't installed, we'll just have a build warning:
Makefile.config:1144: libpfm4 not found, disables libpfm4 support. Please install libpfm4-dev
- Add a feature test for scandirat(), that is not implemented so far
in musl and uclibc, disabling features that need it, such as
scanning for tracepoints in /sys/kernel/tracing/events.
perf BPF filters:
- New feature where BPF can be used to filter samples, for instance:
$ sudo ./perf record -e cycles --filter 'period > 1000' true
$ sudo ./perf script
perf-exec 2273949 546850.708501: 5029 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708508: 32409 cycles: ffffffff826f9e25 finish_wait+0x5 ([kernel.kallsyms])
perf-exec 2273949 546850.708526: 143369 cycles: ffffffff82b4cdbf xas_start+0x5f ([kernel.kallsyms])
perf-exec 2273949 546850.708600: 372650 cycles: ffffffff8286b8f7 __pagevec_lru_add+0x117 ([kernel.kallsyms])
perf-exec 2273949 546850.708791: 482953 cycles: ffffffff829190de __mod_memcg_lruvec_state+0x4e ([kernel.kallsyms])
true 2273949 546850.709036: 501985 cycles: ffffffff828add7c tlb_gather_mmu+0x4c ([kernel.kallsyms])
true 2273949 546850.709292: 503065 cycles: 7f2446d97c03 _dl_map_object_deps+0x973 (/usr/lib/x86_64-linux-gnu/ld-linux-x86-64.so.2)
- In addition to 'period' (PERF_SAMPLE_PERIOD), the other
PERF_SAMPLE_ can be used for filtering, and also some other sample
accessible values, from tools/perf/Documentation/perf-record.txt:
Essentially the BPF filter expression is:
<term> <operator> <value> (("," | "||") <term> <operator> <value>)*
The <term> can be one of:
ip, id, tid, pid, cpu, time, addr, period, txn, weight, phys_addr,
code_pgsz, data_pgsz, weight1, weight2, weight3, ins_lat, retire_lat,
p_stage_cyc, mem_op, mem_lvl, mem_snoop, mem_remote, mem_lock,
mem_dtlb, mem_blk, mem_hops
The <operator> can be one of:
==, !=, >, >=, <, <=, &
The <value> can be one of:
<number> (for any term)
na, load, store, pfetch, exec (for mem_op)
l1, l2, l3, l4, cxl, io, any_cache, lfb, ram, pmem (for mem_lvl)
na, none, hit, miss, hitm, fwd, peer (for mem_snoop)
remote (for mem_remote)
na, locked (for mem_locked)
na, l1_hit, l1_miss, l2_hit, l2_miss, any_hit, any_miss, walk, fault (for mem_dtlb)
na, by_data, by_addr (for mem_blk)
hops0, hops1, hops2, hops3 (for mem_hops)
perf lock contention:
- Show lock type with address.
- Track and show mmap_lock, siglock and per-cpu rq_lock with address.
This is done for mmap_lock by following the current->mm pointer:
$ sudo ./perf lock con -abl -- sleep 10
contended total wait max wait avg wait address symbol
...
16344 312.30 ms 2.22 ms 19.11 us ffff8cc702595640
17686 310.08 ms 1.49 ms 17.53 us ffff8cc7025952c0
3 84.14 ms 45.79 ms 28.05 ms ffff8cc78114c478 mmap_lock
3557 76.80 ms 68.75 us 21.59 us ffff8cc77ca3af58
1 68.27 ms 68.27 ms 68.27 ms ffff8cda745dfd70
9 54.53 ms 7.96 ms 6.06 ms ffff8cc7642a48b8 mmap_lock
14629 44.01 ms 60.00 us 3.01 us ffff8cc7625f9ca0
3481 42.63 ms 140.71 us 12.24 us ffffffff937906ac vmap_area_lock
16194 38.73 ms 42.15 us 2.39 us ffff8cd397cbc560
11 38.44 ms 10.39 ms 3.49 ms ffff8ccd6d12fbb8 mmap_lock
1 5.43 ms 5.43 ms 5.43 ms ffff8cd70018f0d8
1674 5.38 ms 422.93 us 3.21 us ffffffff92e06080 tasklist_lock
581 4.51 ms 130.68 us 7.75 us ffff8cc9b1259058
5 3.52 ms 1.27 ms 703.23 us ffff8cc754510070
112 3.47 ms 56.47 us 31.02 us ffff8ccee38b3120
381 3.31 ms 73.44 us 8.69 us ffffffff93790690 purge_vmap_area_lock
255 3.19 ms 36.35 us 12.49 us ffff8d053ce30c80
- Update default map size to 16384.
- Allocate single letter option -M for --map-nr-entries, as it is
proving being frequently used.
- Fix struct rq lock access for older kernels with BPF's CO-RE
(Compile once, run everywhere).
- Fix problems found with MSAn.
perf report/top:
- Add inline information when using --call-graph=fp or lbr, as was
already done to the --call-graph=dwarf callchain mode.
- Improve the 'srcfile' sort key performance by really using an
optimization introduced in 6.2 for the 'srcline' sort key that
avoids calling addr2line for comparision with each sample.
perf sched:
- Make 'perf sched latency/map/replay' to use "sched:sched_waking"
instead of "sched:sched_waking", consistent with 'perf record'
since d566a9c2d4 ("perf sched: Prefer sched_waking event when it
exists").
perf ftrace:
- Make system wide the default target for latency subcommand, run the
following command then generate some network traffic and press
control+C:
# perf ftrace latency -T __kfree_skb
^C
DURATION | COUNT | GRAPH |
0 - 1 us | 27 | ############# |
1 - 2 us | 22 | ########### |
2 - 4 us | 8 | #### |
4 - 8 us | 5 | ## |
8 - 16 us | 24 | ############ |
16 - 32 us | 2 | # |
32 - 64 us | 1 | |
64 - 128 us | 0 | |
128 - 256 us | 0 | |
256 - 512 us | 0 | |
512 - 1024 us | 0 | |
1 - 2 ms | 0 | |
2 - 4 ms | 0 | |
4 - 8 ms | 0 | |
8 - 16 ms | 0 | |
16 - 32 ms | 0 | |
32 - 64 ms | 0 | |
64 - 128 ms | 0 | |
128 - 256 ms | 0 | |
256 - 512 ms | 0 | |
512 - 1024 ms | 0 | |
1 - ... s | 0 | |
#
perf top:
- Add --branch-history (LBR: Last Branch Record) option, just like
already available for 'perf record'.
- Fix segfault in thread__comm_len() where thread->comm was being
used outside thread->comm_lock.
perf annotate:
- Allow configuring objdump and addr2line in ~/.perfconfig., so that
you can use alternative binaries, such as llvm's.
perf kvm:
- Add TUI mode for 'perf kvm stat report'.
Reference counting:
- Add reference count checking infrastructure to check for use after
free, done to the 'cpumap', 'namespaces', 'maps' and 'map' structs,
more to come.
To build with it use -DREFCNT_CHECKING=1 in the make command line
to build tools/perf. Documented at:
https://perf.wiki.kernel.org/index.php/Reference_Count_Checking
- The above caught, for instance, fix, present in this series:
- Fix maps use after put in 'perf test "Share thread maps"':
'maps' is copied from leader, but the leader is put on line 79
and then 'maps' is used to read the reference count below - so
a use after put, with the put of maps happening within
thread__put.
Fixed by reversing the order of puts so that the leader is put
last.
- Also several fixes were made to places where reference counts were
not being held.
- Make this one of the tests in 'make -C tools/perf build-test' to
regularly build test it and to make sure no direct access to the
reference counted structs are made, doing that via accessors to
check the validity of the struct pointer.
ARM64:
- Fix 'perf report' segfault when filtering coresight traces by
sparse lists of CPUs.
- Add support for 'simd' as a sort field for 'perf report', to show
ARM's NEON SIMD's predicate flags: "partial" and "empty".
arm64 vendor events:
- Add N1 metrics.
Intel vendor events:
- Add graniterapids, grandridge and sierraforrest events.
- Refresh events for: alderlake, aldernaken, broadwell, broadwellde,
broadwellx, cascadelakx, haswell, haswellx, icelake, icelakex,
jaketown, meteorlake, knightslanding, sandybridge, sapphirerapids,
silvermont, skylake, tigerlake and westmereep-dp
- Refresh metrics for alderlake-n, broadwell, broadwellde,
broadwellx, haswell, haswellx, icelakex, ivybridge, ivytown and
skylakex.
perf stat:
- Implement --topdown using JSON metrics.
- Add TopdownL1 JSON metric as a default if present, but disable it
for now for some Intel hybrid architectures, a series of patches
addressing this is being reviewed and will be submitted for v6.5.
- Use metrics for --smi-cost.
- Update topdown documentation.
Vendor events (JSON) infrastructure:
- Add support for computing and printing metric threshold values. For
instance, here is one found in thesapphirerapids json file:
{
"BriefDescription": "Percentage of cycles spent in System Management Interrupts.",
"MetricExpr": "((msr@aperf@ - cycles) / msr@aperf@ if msr@smi@ > 0 else 0)",
"MetricGroup": "smi",
"MetricName": "smi_cycles",
"MetricThreshold": "smi_cycles > 0.1",
"ScaleUnit": "100%"
},
- Test parsing metric thresholds with the fake PMU in 'perf test
pmu-events'.
- Support for printing metric thresholds in 'perf list'.
- Add --metric-no-threshold option to 'perf stat'.
- Add rand (reverse and) and has_pmem (optane memory) support to
metrics.
- Sort list of input files to avoid depending on the order from
readdir() helping in obtaining reproducible builds.
S/390:
- Add common metrics: - CPI (cycles per instruction), prbstate (ratio
of instructions executed in problem state compared to total number
of instructions), l1mp (Level one instruction and data cache misses
per 100 instructions).
- Add cache metrics for z13, z14, z15 and z16.
- Add metric for TLB and cache.
ARM:
- Add raw decoding for SPE (Statistical Profiling Extension) v1.3 MTE
(Memory Tagging Extension) and MOPS (Memory Operations) load/store.
Intel PT hardware tracing:
- Add event type names UINTR (User interrupt delivered) and UIRET
(Exiting from user interrupt routine), documented in table 32-50
"CFE Packet Type and Vector Fields Details" in the Intel Processor
Trace chapter of The Intel SDM Volume 3 version 078.
- Add support for new branch instructions ERETS and ERETU.
- Fix CYC timestamps after standalone CBR
ARM CoreSight hardware tracing:
- Allow user to override timestamp and contextid settings.
- Fix segfault in dso lookup.
- Fix timeless decode mode detection.
- Add separate decode paths for timeless and per-thread modes.
auxtrace:
- Fix address filter entire kernel size.
Miscellaneous:
- Fix use-after-free and unaligned bugs in the PLT handling routines.
- Use zfree() to reduce chances of use after free.
- Add missing 0x prefix for addresses printed in hexadecimal in 'perf
probe'.
- Suppress massive unsupported target platform errors in the unwind
code.
- Fix return incorrect build_id size in elf_read_build_id().
- Fix 'perf scripts intel-pt-events.py' IPC output for Python 2 .
- Add missing new parameter in kfree_skb tracepoint to the python
scripts using it.
- Add 'perf bench syscall fork' benchmark.
- Add support for printing PERF_MEM_LVLNUM_UNC (Uncached access) in
'perf mem'.
- Fix wrong size expectation for perf test 'Setup struct
perf_event_attr' caused by the patch adding
perf_event_attr::config3.
- Fix some spelling mistakes"
* tag 'perf-tools-for-v6.4-3-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (365 commits)
Revert "perf build: Make BUILD_BPF_SKEL default, rename to NO_BPF_SKEL"
Revert "perf build: Warn for BPF skeletons if endian mismatches"
perf metrics: Fix SEGV with --for-each-cgroup
perf bpf skels: Stop using vmlinux.h generated from BTF, use subset of used structs + CO-RE
perf stat: Separate bperf from bpf_profiler
perf test record+probe_libc_inet_pton: Fix call chain match on x86_64
perf test record+probe_libc_inet_pton: Fix call chain match on s390
perf tracepoint: Fix memory leak in is_valid_tracepoint()
perf cs-etm: Add fix for coresight trace for any range of CPUs
perf build: Fix unescaped # in perf build-test
perf unwind: Suppress massive unsupported target platform errors
perf script: Add new parameter in kfree_skb tracepoint to the python scripts using it
perf script: Print raw ip instead of binary offset for callchain
perf symbols: Fix return incorrect build_id size in elf_read_build_id()
perf list: Modify the warning message about scandirat(3)
perf list: Fix memory leaks in print_tracepoint_events()
perf lock contention: Rework offset calculation with BPF CO-RE
perf lock contention: Fix struct rq lock access
perf stat: Disable TopdownL1 on hybrid
perf stat: Avoid SEGV on counter->name
...
Pull debugobjects fix from Thomas Gleixner:
"A single fix for debugobjects:
The recent fix to ensure atomicity of lookup and allocation
inadvertently broke the pool refill mechanism, so that debugobject
OOMs now in certain situations. The reason is that the functions which
got updated no longer invoke debug_objecs_init(), which is now the
only place to care about refilling the tracking object pool.
Restore the original behaviour by adding explicit refill opportunities
to those places"
* tag 'core-debugobjects-2023-05-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
debugobject: Ensure pool refill (again)
Pull crypto fixes from Herbert Xu:
- A long-standing bug in crypto_engine
- A buggy but harmless check in the sun8i-ss driver
- A regression in the CRYPTO_USER interface
* tag 'v6.4-p2' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: api - Fix CRYPTO_USER checks for report function
crypto: engine - fix crypto_queue backlog handling
crypto: sun8i-ss - Fix a test in sun8i_ss_setup_ivs()
Pull cifs fixes from Steve French:
"smb3 client fixes, mostly DFS or reconnect related:
- Two DFS connection sharing fixes
- DFS refresh fix
- Reconnect fix
- Two potential use after free fixes
- Also print prefix patch in mount debug msg
- Two small cleanup fixes"
* tag '6.4-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Remove unneeded semicolon
cifs: fix sharing of DFS connections
cifs: avoid potential races when handling multiple dfs tcons
cifs: protect access of TCP_Server_Info::{origin,leaf}_fullpath
cifs: fix potential race when tree connecting ipc
cifs: fix potential use-after-free bugs in TCP_Server_Info::hostname
cifs: print smb3_fs_context::source when mounting
cifs: protect session status check in smb2_reconnect()
SMB3.1.1: correct definition for app_instance_id create contexts
Pull clk fixes from Stephen Boyd:
"A couple more patches that would be good to get into -rc1:
- Revert an i.MX patch that's causing video failures because division
math goes sideways
- Fix a clang + W=1 build isue where FIELD_PREP() is taking a 32-bit
variable instead of the usual u64 type
- Fix a Kconfig bug in the StarFive JH7110 clk config that selects a
reset controller when it can't be selected"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: starfive: Fix RESET_STARFIVE_JH7110 can't be selected in a specified case
clk: sp7021: Adjust width of _m in HWM_FIELD_PREP()
Revert "clk: imx: composite-8m: Add support to determine_rate"
Pull mailbox updates from Jassi Brar:
- mailbox api: allow direct registration to a channel and convert omap
and pcc to use mbox_bind_client
- omap and hi6220 : use of_property_read_bool
- test: fix double-free and use spinlock header
- rockchip and bcm-pdc: drop of_match_ptr
- mpfs: change config symbol
- mediatek gce: support MT6795
- qcom apcs: consolidate of_device_id and support IPQ9574
* tag 'mailbox-v6.4' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
dt-bindings: mailbox: qcom: add compatible for IPQ9574 SoC
mailbox: qcom-apcs-ipc: do not grow the of_device_id
dt-bindings: mailbox: qcom,apcs-kpss-global: use fallbacks for few variants
dt-bindings: mailbox: mediatek,gce-mailbox: Add support for MT6795
mailbox: mpfs: convert SOC_MICROCHIP_POLARFIRE to ARCH_MICROCHIP_POLARFIRE
mailbox: bcm-pdc: drop of_match_ptr for ID table
mailbox: rockchip: drop of_match_ptr for ID table
mailbox: mailbox-test: Fix potential double-free in mbox_test_message_write()
mailbox: mailbox-test: Explicitly include header for spinlock support
mailbox: Use of_property_read_bool() for boolean properties
mailbox: pcc: Use mbox_bind_client
mailbox: omap: Use mbox_bind_client
mailbox: Allow direct registration to a channel
Pull more io_uring updates from Jens Axboe:
"Nothing major in here, just two different parts:
- A small series from Breno that enables passing the full SQE down
for ->uring_cmd().
This is a prerequisite for enabling full network socket operations.
Queued up a bit late because of some stylistic concerns that got
resolved, would be nice to have this in 6.4-rc1 so the dependent
work will be easier to handle for 6.5.
- Fix for the huge page coalescing, which was a regression introduced
in the 6.3 kernel release (Tobias)"
* tag 'for-6.4/io_uring-2023-05-07' of git://git.kernel.dk/linux:
io_uring: Remove unnecessary BUILD_BUG_ON
io_uring: Pass whole sqe to commands
io_uring: Create a helper to return the SQE size
io_uring/rsrc: check for nonconsecutive pages
