Marc Kleine-Budde says:
====================
pull-request: can 2019-12-03
this is a pull request of 6 patches for net/master.
The first two patches are against the MAINTAINERS file and adds Appana
Durga Kedareswara rao as maintainer for the xilinx-can driver and Sriram
Dash for the m_can (mmio) driver.
The next patch is by Jouni Hogander and fixes a use-after-free in the
slcan driver.
Johan Hovold's patch for the ucan driver fixes the non-atomic allocation
in the completion handler.
The last two patches target the xilinx-can driver. The first one is by
Venkatesh Yadav Abbarapu and skips the error message on deferred probe,
the second one is by Srinivas Neeli and fixes the usage of the skb after
can_put_echo_skb().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the CAN bus clock is provided from the clock wizard, clock wizard
driver may not be available when can driver probes resulting to the
error message "bus clock not found error".
As this error message is not very useful to the end user, skip printing
in the case of deferred probe.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Appana Durga Kedareswara Rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Slcan_open doesn't clean-up device which registration failed from the
slcan_devs device list. On next open this list is iterated and freed
device is accessed. Fix this by calling slc_free_netdev in error path.
Driver/net/can/slcan.c is derived from slip.c. Use-after-free error was
identified in slip_open by syzboz. Same bug is in slcan.c. Here is the
trace from the Syzbot slip report:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x197/0x210 lib/dump_stack.c:118
print_address_description.constprop.0.cold+0xd4/0x30b mm/kasan/report.c:374
__kasan_report.cold+0x1b/0x41 mm/kasan/report.c:506
kasan_report+0x12/0x20 mm/kasan/common.c:634
__asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132
sl_sync drivers/net/slip/slip.c:725 [inline]
slip_open+0xecd/0x11b7 drivers/net/slip/slip.c:801
tty_ldisc_open.isra.0+0xa3/0x110 drivers/tty/tty_ldisc.c:469
tty_set_ldisc+0x30e/0x6b0 drivers/tty/tty_ldisc.c:596
tiocsetd drivers/tty/tty_io.c:2334 [inline]
tty_ioctl+0xe8d/0x14f0 drivers/tty/tty_io.c:2594
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0xdb6/0x13e0 fs/ioctl.c:696
ksys_ioctl+0xab/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0xfa/0x760 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: ed50e1600b ("slcan: Fix memory leak in error path")
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: David Miller <davem@davemloft.net>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.4
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since we are actively working on MMIO MCAN device driver,
as discussed with Marc, I am adding myself as a maintainer.
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The skb_mpls_pop was not updating ethertype of an ethernet packet if the
packet was originally received from a non ARPHRD_ETHER device.
In the below OVS data path flow, since the device corresponding to port 7
is an l3 device (ARPHRD_NONE) the skb_mpls_pop function does not update
the ethertype of the packet even though the previous push_eth action had
added an ethernet header to the packet.
recirc_id(0),in_port(7),eth_type(0x8847),
mpls(label=12/0xfffff,tc=0/0,ttl=0/0x0,bos=1/1),
actions:push_eth(src=00:00:00:00:00:00,dst=00:00:00:00:00:00),
pop_mpls(eth_type=0x800),4
Fixes: ed246cee09 ("net: core: move pop MPLS functionality from OvS to core helper")
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-12-02
The following pull-request contains BPF updates for your *net* tree.
We've added 10 non-merge commits during the last 6 day(s) which contain
a total of 10 files changed, 60 insertions(+), 51 deletions(-).
The main changes are:
1) Fix vmlinux BTF generation for binutils pre v2.25, from Stanislav Fomichev.
2) Fix libbpf global variable relocation to take symbol's st_value offset
into account, from Andrii Nakryiko.
3) Fix libbpf build on powerpc where check_abi target fails due to different
readelf output format, from Aurelien Jarno.
4) Don't set BPF insns RO for the case when they are JITed in order to avoid
fragmenting the direct map, from Daniel Borkmann.
5) Fix static checker warning in btf_distill_func_proto() as well as a build
error due to empty enum when BPF is compiled out, from Alexei Starovoitov.
6) Fix up generation of bpf_helper_defs.h for perf, from Arnaldo Carvalho de Melo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On powerpc with recent versions of binutils, readelf outputs an extra
field when dumping the symbols of an object file. For example:
35: 0000000000000838 96 FUNC LOCAL DEFAULT [<localentry>: 8] 1 btf_is_struct
The extra "[<localentry>: 8]" prevents the GLOBAL_SYM_COUNT variable to
be computed correctly and causes the check_abi target to fail.
Fix that by looking for the symbol name in the last field instead of the
8th one. This way it should also cope with future extra fields.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/bpf/20191201195728.4161537-1-aurelien@aurel32.net
Merge updates from Andrew Morton:
"Incoming:
- a small number of updates to scripts/, ocfs2 and fs/buffer.c
- most of MM
I still have quite a lot of material (mostly not MM) staged after
linux-next due to -next dependencies. I'll send those across next week
as the preprequisites get merged up"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (135 commits)
mm/page_io.c: annotate refault stalls from swap_readpage
mm/Kconfig: fix trivial help text punctuation
mm/Kconfig: fix indentation
mm/memory_hotplug.c: remove __online_page_set_limits()
mm: fix typos in comments when calling __SetPageUptodate()
mm: fix struct member name in function comments
mm/shmem.c: cast the type of unmap_start to u64
mm: shmem: use proper gfp flags for shmem_writepage()
mm/shmem.c: make array 'values' static const, makes object smaller
userfaultfd: require CAP_SYS_PTRACE for UFFD_FEATURE_EVENT_FORK
fs/userfaultfd.c: wp: clear VM_UFFD_MISSING or VM_UFFD_WP during userfaultfd_register()
userfaultfd: wrap the common dst_vma check into an inlined function
userfaultfd: remove unnecessary WARN_ON() in __mcopy_atomic_hugetlb()
userfaultfd: use vma_pagesize for all huge page size calculation
mm/madvise.c: use PAGE_ALIGN[ED] for range checking
mm/madvise.c: replace with page_size() in madvise_inject_error()
mm/mmap.c: make vma_merge() comment more easy to understand
mm/hwpoison-inject: use DEFINE_DEBUGFS_ATTRIBUTE to define debugfs fops
autonuma: reduce cache footprint when scanning page tables
autonuma: fix watermark checking in migrate_balanced_pgdat()
...
Pull networking fixes from David Miller:
1) Fix several scatter gather list issues in kTLS code, from Jakub
Kicinski.
2) macb driver device remove has to kill the hresp_err_tasklet. From
Chuhong Yuan.
3) Several memory leak and reference count bug fixes in tipc, from Tung
Nguyen.
4) Fix mlx5 build error w/o ipv6, from Yue Haibing.
5) Fix jumbo frame and other regressions in r8169, from Heiner
Kallweit.
6) Undo some BUG_ON()'s and replace them with WARN_ON_ONCE and proper
error propagation/handling. From Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (24 commits)
openvswitch: remove another BUG_ON()
openvswitch: drop unneeded BUG_ON() in ovs_flow_cmd_build_info()
net: phy: realtek: fix using paged operations with RTL8105e / RTL8208
r8169: fix resume on cable plug-in
r8169: fix jumbo configuration for RTL8168evl
net: emulex: benet: indent a Kconfig depends continuation line
selftests: forwarding: fix race between packet receive and tc check
net: sched: fix `tc -s class show` no bstats on class with nolock subqueues
net: ethernet: ti: ale: ensure vlan/mdb deleted when no members
net/mlx5e: Fix build error without IPV6
selftests: pmtu: use -oneline for ip route list cache
tipc: fix duplicate SYN messages under link congestion
tipc: fix wrong timeout input for tipc_wait_for_cond()
tipc: fix wrong socket reference counter after tipc_sk_timeout() returns
tipc: fix potential memory leak in __tipc_sendmsg()
net: macb: add missed tasklet_kill
selftests: bpf: correct perror strings
selftests: bpf: test_sockmap: handle file creation failures gracefully
net/tls: use sg_next() to walk sg entries
net/tls: remove the dead inplace_crypto code
...
Pull x86 fixes from Ingo Molnar:
"Various fixes:
- Fix the PAT performance regression that downgraded write-combining
device memory regions to uncached.
- There's been a number of bugs in 32-bit double fault handling -
hopefully all fixed now.
- Fix an LDT crash
- Fix an FPU over-optimization that broke with GCC9 code
optimizations.
- Misc cleanups"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/pat: Fix off-by-one bugs in interval tree search
x86/ioperm: Save an indentation level in tss_update_io_bitmap()
x86/fpu: Don't cache access to fpu_fpregs_owner_ctx
x86/entry/32: Remove unused 'restore_all_notrace' local label
x86/ptrace: Document FSBASE and GSBASE ABI oddities
x86/ptrace: Remove set_segment_reg() implementations for current
x86/traps: die() instead of panicking on a double fault
x86/doublefault/32: Rewrite the x86_32 #DF handler and unify with 64-bit
x86/doublefault/32: Move #DF stack and TSS to cpu_entry_area
x86/doublefault/32: Rename doublefault.c to doublefault_32.c
x86/traps: Disentangle the 32-bit and 64-bit doublefault code
lkdtm: Add a DOUBLE_FAULT crash type on x86
selftests/x86/single_step_syscall: Check SYSENTER directly
x86/mm/32: Sync only to VMALLOC_END in vmalloc_sync_all()
Pull perf fixes from Ingo Molnar:
- Make /sys/devices/cpu/rdpmc based RDPMC enforcement more
instantaneous
- decoder: Update the Intel opcode map
- Various tooling fixes, including a few late optimizations and
cleanups.
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
perf script: Fix invalid LBR/binary mismatch error
perf script: Fix brstackinsn for AUXTRACE
perf affinity: Add infrastructure to save/restore affinity
perf pmu: Use file system cache to optimize sysfs access
perf regs: Make perf_reg_name() return "unknown" instead of NULL
perf diff: Use llabs() with 64-bit values
perf diff: Use llabs() with 64-bit values
perf/x86: Implement immediate enforcement of /sys/devices/cpu/rdpmc value of 0
perf tools: Allow to link with libbpf dynamicaly
perf tests: Rename tests/map_groups.c to tests/maps.c
perf tests: Rename thread-mg-share to thread-maps-share
perf maps: Rename map_groups.h to maps.h
perf maps: Rename 'mg' variables to 'maps'
perf map_symbol: Rename ms->mg to ms->maps
perf addr_location: Rename al->mg to al->maps
perf thread: Rename thread->mg to thread->maps
perf maps: Merge 'struct maps' with 'struct map_groups'
x86/insn: perf tools: Add some more instructions to the new instructions test
x86/insn: Add some more Intel instructions to the opcode map
perf map: Remove unused functions
...
Pull input updates from Dmitry Torokhov:
- updates to Ilitech driver to support ILI2117
- face lift of st1232 driver to support MT-B protocol
- a new driver for i.MX system controller keys
- mpr121 driver now supports polling mode
- various input drivers have been switched away from input_polled_dev
to use polled mode of regular input devices
- other assorted cleanups and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (70 commits)
Input: synaptics-rmi4 - fix various V4L2 compliance problems in F54
Input: synaptics - switch another X1 Carbon 6 to RMI/SMbus
Input: fix Kconfig indentation
Input: imx_sc_key - correct SCU message structure to avoid stack corruption
Input: ili210x - optionally show calibrate sysfs attribute
Input: ili210x - add resolution to chip operations structure
Input: ili210x - do not retrieve/print chip firmware version
Input: mms114 - use device_get_match_data
Input: ili210x - remove unneeded suspend and resume handlers
Input: ili210x - do not unconditionally mark touchscreen as wakeup source
Input: ili210x - define and use chip operations structure
Input: ili210x - do not set parent device explicitly
Input: ili210x - handle errors from input_mt_init_slots()
Input: ili210x - switch to using threaded IRQ
Input: ili210x - add ILI2117 support
dt-bindings: input: touchscreen: ad7879: generic node names in example
Input: ar1021 - fix typo in preprocessor macro name
Input: synaptics-rmi4 - simplify data read in rmi_f54_work
Input: kxtj9 - switch to using polled mode of input devices
Input: kxtj9 - switch to using managed resources
...
Pull libnvdimm updates from Dan Williams:
"The highlight this cycle is continuing integration fixes for PowerPC
and some resulting optimizations.
Summary:
- Updates to better support vmalloc space restrictions on PowerPC
platforms.
- Cleanups to move common sysfs attributes to core 'struct
device_type' objects.
- Export the 'target_node' attribute (the effective numa node if pmem
is marked online) for regions and namespaces.
- Miscellaneous fixups and optimizations"
* tag 'libnvdimm-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: (21 commits)
MAINTAINERS: Remove Keith from NVDIMM maintainers
libnvdimm: Export the target_node attribute for regions and namespaces
dax: Add numa_node to the default device-dax attributes
libnvdimm: Simplify root read-only definition for the 'resource' attribute
dax: Simplify root read-only definition for the 'resource' attribute
dax: Create a dax device_type
libnvdimm: Move nvdimm_bus_attribute_group to device_type
libnvdimm: Move nvdimm_attribute_group to device_type
libnvdimm: Move nd_mapping_attribute_group to device_type
libnvdimm: Move nd_region_attribute_group to device_type
libnvdimm: Move nd_numa_attribute_group to device_type
libnvdimm: Move nd_device_attribute_group to device_type
libnvdimm: Move region attribute group definition
libnvdimm: Move attribute groups to device type
libnvdimm: Remove prototypes for nonexistent functions
libnvdimm/btt: fix variable 'rc' set but not used
libnvdimm/pmem: Delete include of nd-core.h
libnvdimm/namespace: Differentiate between probe mapping and runtime mapping
libnvdimm/pfn_dev: Don't clear device memmap area during generic namespace probe
libnvdimm: Trivial comment fix
...
Pull mailbox updates from Jassi Brar:
- omap : misc - catch error returned from pm_runtime_put_sync
- hisi : misc - drop .owner from platform_driver
- stm : change how wakeup is handled
- imx : fix - bailout on error and nuke correct irq
- imx : add support for imx7ulp platform
* tag 'mailbox-v5.5' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: imx: add support for imx v1 mu
dt-bindings: mailbox: imx-mu: add imx7ulp MU support
mailbox: imx: Clear the right interrupts at shutdown
mailbox: imx: Fix Tx doorbell shutdown path
mailbox: stm32-ipcc: Update wakeup management
mailbox: no need to set .owner platform_driver_register
mailbox/omap: Handle if CONFIG_PM is disabled
Pull hwspinlock updates from Bjorn Andersson:
"This contains a number of cleanups to the core and several drivers, in
particular removing the requirement for drivers to implement
pm_runtime.
It also udpates the location of the git tree in MAINTAINERS"
* tag 'hwlock-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
hwspinlock: u8500_hsem: Remove redundant PM runtime implementation
hwspinlock: sprd: Remove redundant PM runtime implementation
hwspinlock: Let the PM runtime can be optional
hwspinlock: Remove BUG_ON() from the hwspinlock core
hwspinlock: sprd: Use devm_hwspin_lock_register() to register hwlock controller
hwspinlock: sprd: Use devm_add_action_or_reset() for calls to clk_disable_unprepare()
hwspinlock: sprd: Check the return value of clk_prepare_enable()
hwspinlock: sprd: Change to use devm_platform_ioremap_resource()
hwspinlock: u8500_hsem: Use devm_hwspin_lock_register() to register hwlock controller
hwspinlock: u8500_hsem: Use devm_kzalloc() to allocate memory
hwspinlock: u8500_hsem: Change to use devm_platform_ioremap_resource()
MAINTAINERS: hwspinlock: update git tree location
Pull rpmsg updates from Bjorn Andersson:
"This contains a number of bug fixes to the GLINK transport driver, an
off-by-one in the GLINK smem driver and a memory leak fix in the rpmsg
char driver"
* tag 'rpmsg-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
rpmsg: Fix Kconfig indentation
rpmsg: char: Simplify 'rpmsg_eptdev_release()'
rpmsg: glink: Free pending deferred work on remove
rpmsg: glink: Don't send pending rx_done during remove
rpmsg: glink: Fix rpmsg_register_device err handling
rpmsg: glink: Put an extra reference during cleanup
rpmsg: glink: Fix use after free in open_ack TIMEOUT case
rpmsg: glink: Fix reuse intents memory leak issue
rpmsg: glink: Set tail pointer to 0 at end of FIFO
rpmsg: char: release allocated memory
Pull remoteproc updates from Bjorn Andersson:
"This adds support for booting the modem processor on Qualcomm MSM8998
and carries some cleanup up and bug fixes to the framework and the
stm32 driver"
* tag 'rproc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc:
Revert "dt-bindings: remoteproc: stm32: add wakeup-source"
remoteproc: stm32: fix probe error case
remoteproc: stm32: wakeup the system by wdg irq
dt-bindings: remoteproc: stm32: add wakeup-source
remoteproc: Fix wrong rvring index computation
remoteproc: stm32: use workqueue to treat mailbox callback
remoteproc: fix argument 2 of rproc_mem_entry_init
remoteproc: qcom_q6v5_mss: Add support for MSM8998
dt-bindings: remoteproc: qcom: Add Q6v5 Modem PIL binding for MSM8998
remoteproc: debug: Remove unneeded NULL check
remoteproc: remove useless typedef
Pull i2c updates from Wolfram Sang:
"I2C has mostly driver updates this time.
The few noteworthy changes are: the core has now support for analog
and digital filters with at91 being the first user, a core addition to
replace the NULL returning i2c_new_probed_device() with an ERR_PTR
variant, and the pxa driver has finally being moved to use the generic
I2C slave interface. We have quite a significant number of reviews per
patch this time, so thank you to all involved!"
* 'i2c/for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
video: fbdev: matrox: convert to i2c_new_scanned_device
i2c: icy: convert to i2c_new_scanned_device
i2c: replace i2c_new_probed_device with an ERR_PTR variant
i2c: Fix Kconfig indentation
i2c: smbus: Don't filter out duplicate alerts
i2c: i801: Correct Intel Jasper Lake SOC naming
i2c: i2c-stm32f7: fix 10-bits check in slave free id search loop
i2c: iproc: Add i2c repeated start capability
i2c: remove helpers for ref-counting clients
i2c: tegra: Use dma_request_chan() directly for channel request
i2c: sh_mobile: Use dma_request_chan() directly for channel request
i2c: qup: Use dma_request_chan() directly for channel request
i2c: at91: Use dma_request_chan() directly for channel request
i2c: rcar: Remove superfluous call to clk_get_rate()
i2c: pxa: remove unused i2c-slave APIs
i2c: pxa: migrate to new i2c_slave APIs
i2c: cros-ec-tunnel: Make the device acpi compatible
i2c: stm32f7: report dma error during probe
i2c: icy: no need to populate address for scanned device
i2c: xiic: Fix kerneldoc warnings
...
Pull block fixes from Jens Axboe:
"I wasn't going to send this one off so soon, but unfortunately one of
the fixes from the previous pull broke the build on some archs. So I'm
sending this sooner rather than later. This contains:
- Add highmem.h include for io_uring, because of the kmap() additions
from last round. For some reason the build bot didn't spot this
even though it sat for days.
- Three minor ';' removals
- Add support for the Beurer CD-on-a-chip device
- Make io_uring work on MMU-less archs"
* tag 'for-linus-20191129' of git://git.kernel.dk/linux-block:
io_uring: fix missing kmap() declaration on powerpc
ataflop: Remove unneeded semicolon
block: sunvdc: Remove unneeded semicolon
drbd: Remove unneeded semicolon
io_uring: add mapping support for NOMMU archs
sr_vendor: support Beurer GL50 evo CD-on-a-chip devices.
cdrom: respect device capabilities during opening action
Pull x86 platform driver updates from Andy Shevchenko:
- New bootctl driver for Mellanox BlueField SoC.
- New driver to support System76 laptops.
- Temperature monitoring and fan control on Acer Aspire 7551 is now
supported.
- Previously the Huawei driver handled only hotkeys. After the
conversion to WMI it has been expanded to support newer laptop
models.
- Big refactoring of intel-speed-select tools allows to use it on Intel
CascadeLake-N systems.
- Touchscreen support for ezpad 6 m4 and Schneider SCT101CTM tablets
- Miscellaneous clean ups and fixes here and there.
* tag 'platform-drivers-x86-v5.5-1' of git://git.infradead.org/linux-platform-drivers-x86: (59 commits)
platform/x86: hp-wmi: Fix ACPI errors caused by passing 0 as input size
platform/x86: hp-wmi: Fix ACPI errors caused by too small buffer
platform/x86: intel_pmc_core: Add Comet Lake (CML) platform support to intel_pmc_core driver
platform/x86: intel_pmc_core: Fix the SoC naming inconsistency
platform/mellanox: Fix Kconfig indentation
tools/power/x86/intel-speed-select: Display TRL buckets for just base config level
tools/power/x86/intel-speed-select: Ignore missing config level
platform/x86: touchscreen_dmi: Add info for the ezpad 6 m4 tablet
tools/power/x86/intel-speed-select: Increment version
tools/power/x86/intel-speed-select: Use core count for base-freq mask
tools/power/x86/intel-speed-select: Support platform with limited Intel(R) Speed Select
tools/power/x86/intel-speed-select: Use Frequency weight for CLOS
tools/power/x86/intel-speed-select: Make CLOS frequency in MHz
tools/power/x86/intel-speed-select: Use mailbox for CLOS_PM_QOS_CONFIG
tools/power/x86/intel-speed-select: Auto mode for CLX
tools/power/x86/intel-speed-select: Correct CLX-N frequency units
tools/power/x86/intel-speed-select: Change display of "avx" to "avx2"
tools/power/x86/intel-speed-select: Extend command set for perf-profile
Add touchscreen platform data for the Schneider SCT101CTM tablet
platform/x86: intel_int0002_vgpio: Pass irqchip when adding gpiochip
...
Pull HID updates from Jiri Kosina:
- Support for Logitech G15 (Hans de Goede)
- HID parser improvements, improving support for some devices; e.g.
Windows Precision Touchpad, products from Primax, etc. (Blaž
Hrastnik, Candle Sun)
- robustification of tablet mode support in google-whiskers driver
(Dmitry Torokhov)
- assorted small fixes, device-specific quirks and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (23 commits)
HID: rmi: Check that the RMI_STARTED bit is set before unregistering the RMI transport device
HID: quirks: remove hid-led devices from hid_have_special_driver
HID: Improve Windows Precision Touchpad detection.
HID: i2c-hid: Reset ALPS touchpads on resume
HID: i2c-hid: fix no irq after reset on raydium 3118
HID: logitech-hidpp: Silence intermittent get_battery_capacity errors
HID: i2c-hid: remove orphaned member sleep_delay
HID: quirks: Add quirk for HP MSU1465 PIXART OEM mouse
HID: core: check whether Usage Page item is after Usage ID items
HID: intel-ish-hid: Spelling s/diconnect/disconnect/
HID: google: Detect base folded usage instead of hard-coding whiskers
HID: logitech: Add depends on LEDS_CLASS to Logitech Kconfig entry
HID: lg-g15: Add support for the G510's M1-M3 and MR LEDs
HID: lg-g15: Add support for controlling the G510's RGB backlight
HID: lg-g15: Add support for the G510 keyboards' gaming keys
HID: lg-g15: Add support for the M1-M3 and MR LEDs
HID: lg-g15: Add keyboard and LCD backlight control
HID: Add driver for Logitech gaming keyboards (G15, G15 v2)
Input: Add event-codes for macro keys found on various keyboards
HID: hidraw: replace printk() with corresponding pr_xx() variant
...
Pull watchdog updates from Wim Van Sebroeck:
- support for NCT6116D
- several small fixes and improvements
* tag 'linux-watchdog-5.5-rc1' of git://www.linux-watchdog.org/linux-watchdog: (24 commits)
watchdog: jz4740: Drop dependency on MACH_JZ47xx
watchdog: jz4740: Use regmap provided by TCU driver
watchdog: jz4740: Use WDT clock provided by TCU driver
dt-bindings: watchdog: sama5d4_wdt: add microchip,sam9x60-wdt compatible
watchdog: sama5d4_wdt: cleanup the bit definitions
watchdog: sprd: Fix the incorrect pointer getting from driver data
watchdog: aspeed: Fix clock behaviour for ast2600
watchdog: imx7ulp: Fix reboot hang
watchdog: make nowayout sysfs file writable
watchdog: prevent deferral of watchdogd wakeup on RT
watchdog: imx7ulp: Use definitions instead of magic values
watchdog: imx7ulp: Remove inline annotations
watchdog: imx7ulp: Remove unused structure member
watchdog: imx7ulp: Pass the wdog instance inimx7ulp_wdt_enable()
watchdog: wdat_wdt: Spelling s/configrable/configurable/
watchdog: bd70528: Trivial function documentation fix
watchdog: cadence: Do not show error in case of deferred probe
watchdog: Fix the race between the release of watchdog_core_data and cdev
watchdog: sbc7240_wdt: Fix yet another -Wimplicit-fallthrough warning
watchdog: intel-mid_wdt: Add WATCHDOG_NOWAYOUT support
...
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.5 kernel cycle
Core changes:
- Expose pull up/down flags for the GPIO character device to
userspace.
After clear input from the RaspberryPi and Beagle communities, it
has been established that prototyping, industrial automation and
make communities strongly need this feature, and as we want people
to use the character device, we have implemented the simple pull
up/down interface for GPIO lines.
This means we can specify that a (chip-specific) pull up/down
resistor can be enabled, but does not offer fine-grained control
such as cases where the resistance of the same pull resistor can be
controlled (yet).
- Introduce devm_fwnode_gpiod_get_index() and start to phase out the
old symbol devm_fwnode_get_index_gpiod_from_child().
- A bit of documentation clean-up work.
- Introduce a define for GPIO line directions and deploy it in all
GPIO drivers in the drivers/gpio directory.
- Add a special callback to populate pin ranges when cooperating with
the pin control subsystem and registering ranges as part of adding
a gpiolib driver and a gpio_irq_chip driver at the same time. This
is also deployed in the Intel Merrifield driver.
New drivers:
- RDA Micro GPIO controller.
- XGS-iproc GPIO driver.
Driver improvements:
- Wake event and debounce support on the Tegra 186 driver.
- Finalize the Aspeed SGPIO driver.
- MPC8xxx uses a normal IRQ handler rather than a chained handler"
* tag 'gpio-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (64 commits)
gpio: Add TODO item for regmap helper
Documentation: gpio: driver.rst: Fix warnings
gpio: of: Fix bogus reference to gpiod_get_count()
gpiolib: Grammar s/manager/managed/
gpio: lynxpoint: Setup correct IRQ handlers
MAINTAINERS: Replace my email by one @kernel.org
gpiolib: acpi: Make acpi_gpiochip_alloc_event always return AE_OK
gpio/mpc8xxx: fix qoriq GPIO reading
gpio: mpc8xxx: Don't overwrite default irq_set_type callback
gpiolib: acpi: Print pin number on acpi_gpiochip_alloc_event errors
gpiolib: fix coding style in gpiod_hog()
drm/bridge: ti-tfp410: switch to using fwnode_gpiod_get_index()
gpio: merrifield: Pass irqchip when adding gpiochip
gpio: merrifield: Add GPIO <-> pin mapping ranges via callback
gpiolib: Introduce ->add_pin_ranges() callback
gpio: mmio: remove untrue leftover comment
gpio: em: Use platform_get_irq() to obtain interrupts
gpio: tegra186: Add debounce support
gpio: tegra186: Program interrupt route mapping
gpio: tegra186: Derive register offsets from bank/port
...
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add support for a "resource managed strongly uncachable ioremap"
call
- Provide a collection of MFD helper macros
- Remove mfd_clone_cell() from MFD core
- Add NULL de-reference protection in MFD core
- Remove superfluous function fd_platform_add_cell() from MFD core
- Honour Device Tree's request to disable a device
New Drivers:
- Add support for MediaTek MT6323 PMIC
New Device Support:
- Add support for Gemini Lake to Intel LPSS PCI
- Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC
CRC
- Add support for PM{I}8950 to Qualcomm SPMI PMIC
- Add support for U8420 to ST-Ericsson DB8500
- Add support for Comet Lake PCH-H to Intel LPSS PCI
New Functionality:
- Add support for requested supply clocks; madera-core
Fix-ups:
- Lower interrupt priority; rk808
- Use provided helpers (macros, group functions, defines); rk808,
ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
- Only allocate IRQs on request; max77620
- Use simplified API; arizona-core
- Remove redundant and/or duplicated code; wm8998-tables, arizona,
syscon
- Device Tree binding fix-ups; madera, max77650, max77693
- Remove mfd_cell->id abuse hack; cs5535-mfd
- Remove only user of mfd_clone_cell(); cs5535-mfd
- Make resources static; rohm-bd70528
Bug Fixes:
- Fix product ID for RK818; rk808
- Fix Power Key; rk808
- Fix booting on the BananaPi; mt6397-core
- Endian fix-ups; twl.h
- Fix static error checker warnings; ti_am335x_tscadc"
* tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (47 commits)
Revert "mfd: syscon: Set name of regmap_config"
mfd: ti_am335x_tscadc: Fix static checker warning
mfd: bd70528: Staticize bit value definitions
mfd: mfd-core: Honour Device Tree's request to disable a child-device
dt-bindings: mfd: max77693: Fix missing curly brace
mfd: intel-lpss: Add Intel Comet Lake PCH-H PCI IDs
mfd: db8500-prcmu: Support U8420-sysclk firmware
dt-bindings: mfd: max77650: Convert the binding document to yaml
mfd: mfd-core: Move pdev->mfd_cell creation back into mfd_add_device()
mfd: mfd-core: Remove usage counting for .{en,dis}able() call-backs
x86: olpc-xo1-sci: Remove invocation of MFD's .enable()/.disable() call-backs
x86: olpc-xo1-pm: Remove invocation of MFD's .enable()/.disable() call-backs
mfd: mfd-core: Remove mfd_clone_cell()
mfd: mfd-core: Protect against NULL call-back function pointer
mfd: cs5535-mfd: Register clients using their own dedicated MFD cell entries
mfd: cs5535-mfd: Request shared IO regions centrally
mfd: cs5535-mfd: Remove mfd_cell->id hack
mfd: cs5535-mfd: Use PLATFORM_DEVID_* defines and tidy error message
mfd: intel_soc_pmic_crc: Add "cht_crystal_cove_pmic" cell to CHT cells
mfd: madera: Add support for requesting the supply clocks
...
Pull backlight updates from Lee Jones:
"New Functionality:
- Add support for an enable GPIO; lm3630a_bl
- Add support for short circuit handling; qcom-wled
- Add support for automatic string detection; qcom-wled
Fix-ups:
- Update Device Tree bindings; lm3630a-backlight, led-backlight,
qcom-wled
- Constify; ipaq_micro_bl
- Optimise for CPU cycles; pwm_bl
- Coding style fix-ups; pwm_bl
- Trivial fix-ups (white space, comments, renaming); pwm_bl,
gpio_backlight, qcom-wled
- Kconfig dependency hacking; LCD_HP700
- Rename, refactor and add peripherals; pm8941-wled => qcom-wled
- Make use of GPIO look-up tables; tosa_bl, tosa_lcd
- Remove superfluous code; gpio_backlight
- Adapt GPIO direction handling; gpio_backlight
- Remove legacy use of platform data; gpio_backlight
Bug Fixes:
- Provide modules aliases; lm3630a_bl"
* tag 'backlight-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight: (32 commits)
backlight: qcom-wled: Fix spelling mistake "trigged" -> "triggered"
backlight: gpio: Pull gpio_backlight_initial_power_state() into probe
backlight: gpio: Use a helper variable for &pdev->dev
backlight: gpio: Remove unused fields from platform data
sh: ecovec24: don't set unused fields in platform data
backlight: gpio: Simplify the platform data handling
sh: ecovec24: add additional properties to the backlight device
backlight: gpio: Explicitly set the direction of the GPIO
backlight: gpio: Remove stray newline
backlight: gpio: Remove unneeded include
video: backlight: tosa: Use GPIO lookup table
backlight: qcom-wled: Add auto string detection logic
backlight: qcom-wled: Add support for short circuit handling
backlight: qcom-wled: Add support for WLED4 peripheral
backlight: qcom-wled: Restructure the driver for WLED3
backlight: qcom-wled: Rename PM8941* to WLED3
backlight: qcom-wled: Add new properties for PMI8998
backlight: qcom-wled: Restructure the qcom-wled bindings
backlight: qcom-wled: Rename pm8941-wled.c to qcom-wled.c
dt-bindings: backlight: lm3630a: Fix missing include
...
Pull pinctrl fix from Linus Walleij:
"A oneliner fix adding the license to the new Intel pin controller,
avoiding a build-time warning"
* tag 'pinctrl-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: Fix warning by adding missing MODULE_LICENSE
Pull LED updates from Pavel Machek:
"This contains usual small updates to drivers, and removal of PAGE_SIZE
limits on /sys/class/leds/<led>/trigger.
We should not be really having that many triggers; but with cpu
activity triggers we do, and we'll eventually need to fix it, but...
remove the limit for now"
* tag 'leds-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds: (26 commits)
leds: trigger: netdev: fix handling on interface rename
leds: an30259a: add a check for devm_regmap_init_i2c
leds: mlxreg: Fix possible buffer overflow
leds: pca953x: Use of_device_get_match_data()
leds: core: Fix leds.h structure documentation
leds: core: Fix devm_classdev_match to reference correct structure
leds: core: Remove extern from header
leds: lm3601x: Convert class registration to device managed
leds: flash: Add devm_* functions to the flash class
leds: flash: Remove extern from the header file
leds: flash: Convert non extended registration to inline
leds: Kconfig: Be consistent with the usage of "LED"
leds: remove PAGE_SIZE limit of /sys/class/leds/<led>/trigger
leds: tlc591xx: update the maximum brightness
leds: lm3692x: Use flags from LM3692X_BRT_CTRL
leds: lm3692x: Use flags from LM3692X_BOOST_CTRL
leds: lm3692x: Handle failure to probe the regulator
leds: lm3692x: Don't overwrite return value in error path
leds: lm3692x: Print error value on dev_err
leds: tlc591xx: use devm_led_classdev_register_ext()
...
Pull clk updates from Stephen Boyd:
"This merge window we have one small clk provider API in the core
framework and then a bunch of driver updates and a handful of new
drivers. In terms of diffstat the Qualcomm and Amlogic drivers are
high up there because of all the clk data introcued by new drivers.
The Nvidia Tegra driver had a lot of work done this cycle too to
support suspend/resume and memory controllers. And the OMAP clk driver
got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data,
mark things static, correct incorrect data in drivers, etc. All the
little things that improve drivers and maintain code health. I will
point out that there's a patch in here for the GPIO clk driver, that
almost nobody uses, which changes behavior and causes clk_set_rate()
to try to change the GPIO gate clk's parent. Other than that things
are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe
suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8
SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system
suspend/resume cycle on exynos542x SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (160 commits)
clk: aspeed: Add RMII RCLK gates for both AST2500 MACs
MAINTAINERS: Add entry for BM1880 SoC clock driver
clk: Add common clock driver for BM1880 SoC
dt-bindings: clock: Add devicetree binding for BM1880 SoC
clk: Add clk_hw_unregister_composite helper function definition
clk: Zero init clk_init_data in helpers
clk: ingenic: Allow drivers to be built with COMPILE_TEST
MAINTAINERS: Update section for Ux500 clock drivers
clk: mark clk_disable_unused() as __init
clk: Fix memory leak in clk_unregister()
clk: Ingenic: Add CGU driver for X1000.
dt-bindings: clock: Add X1000 bindings.
clk: tegra: Use match_string() helper to simplify the code
clk: pxa: fix one of the pxa RTC clocks
clk: sprd: Use IS_ERR() to validate the return value of syscon_regmap_lookup_by_phandle()
clk: armada-xp: remove unused code
clk: tegra: Fix build error without CONFIG_PM_SLEEP
clk: tegra: Add missing stubs for the case of !CONFIG_PM_SLEEP
clk: tegra: Optimize PLLX restore on Tegra20/30
clk: tegra: Add suspend and resume support on Tegra210
...
Pull y2038 cleanups from Arnd Bergmann:
"y2038 syscall implementation cleanups
This is a series of cleanups for the y2038 work, mostly intended for
namespace cleaning: the kernel defines the traditional time_t, timeval
and timespec types that often lead to y2038-unsafe code. Even though
the unsafe usage is mostly gone from the kernel, having the types and
associated functions around means that we can still grow new users,
and that we may be missing conversions to safe types that actually
matter.
There are still a number of driver specific patches needed to get the
last users of these types removed, those have been submitted to the
respective maintainers"
Link: https://lore.kernel.org/lkml/20191108210236.1296047-1-arnd@arndb.de/
* tag 'y2038-cleanups-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (26 commits)
y2038: alarm: fix half-second cut-off
y2038: ipc: fix x32 ABI breakage
y2038: fix typo in powerpc vdso "LOPART"
y2038: allow disabling time32 system calls
y2038: itimer: change implementation to timespec64
y2038: move itimer reset into itimer.c
y2038: use compat_{get,set}_itimer on alpha
y2038: itimer: compat handling to itimer.c
y2038: time: avoid timespec usage in settimeofday()
y2038: timerfd: Use timespec64 internally
y2038: elfcore: Use __kernel_old_timeval for process times
y2038: make ns_to_compat_timeval use __kernel_old_timeval
y2038: socket: use __kernel_old_timespec instead of timespec
y2038: socket: remove timespec reference in timestamping
y2038: syscalls: change remaining timeval to __kernel_old_timeval
y2038: rusage: use __kernel_old_timeval
y2038: uapi: change __kernel_time_t to __kernel_old_time_t
y2038: stat: avoid 'time_t' in 'struct stat'
y2038: ipc: remove __kernel_time_t reference from headers
y2038: vdso: powerpc: avoid timespec references
...
Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
"As part of the cleanup of some remaining y2038 issues, I came to
fs/compat_ioctl.c, which still has a couple of commands that need
support for time64_t.
In completely unrelated work, I spent time on cleaning up parts of
this file in the past, moving things out into drivers instead.
After Al Viro reviewed an earlier version of this series and did a lot
more of that cleanup, I decided to try to completely eliminate the
rest of it and move it all into drivers.
This series incorporates some of Al's work and many patches of my own,
but in the end stops short of actually removing the last part, which
is the scsi ioctl handlers. I have patches for those as well, but they
need more testing or possibly a rewrite"
* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
scsi: sd: enable compat ioctls for sed-opal
pktcdvd: add compat_ioctl handler
compat_ioctl: move SG_GET_REQUEST_TABLE handling
compat_ioctl: ppp: move simple commands into ppp_generic.c
compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
compat_ioctl: unify copy-in of ppp filters
tty: handle compat PPP ioctls
compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
compat_ioctl: handle SIOCOUTQNSD
af_unix: add compat_ioctl support
compat_ioctl: reimplement SG_IO handling
compat_ioctl: move WDIOC handling into wdt drivers
fs: compat_ioctl: move FITRIM emulation into file systems
gfs2: add compat_ioctl support
compat_ioctl: remove unused convert_in_user macro
compat_ioctl: remove last RAID handling code
compat_ioctl: remove /dev/raw ioctl translation
compat_ioctl: remove PCI ioctl translation
compat_ioctl: remove joystick ioctl translation
...
Pull sysctl system call removal from Eric Biederman:
"As far as I can tell we have reached the point where no one enables
the sysctl system call anymore. It still is enabled in a few
defconfigs but they are mostly the rarely used one and in asking
people about that it was more cut & paste enabled than anything else.
This is single commit that just deletes code. Leaving just enough code
so that the deprecated sysctl warning continues to be printed. If my
analysis turns out to be wrong and someone actually cares it will be
easy to revert this commit and have the system call again.
There was one new xtensa defconfig in linux-next that enabled the
system call this cycle and when asked about it the maintainer of the
code replied that it was not enabled on purpose. As of today's
linux-next tree that defconfig no longer enables the system call.
What we saw in the review discussion was that if we go a step farther
than my patch and mess with uapi headers there are pieces of code that
won't compile, but nothing minds the system call actually disappearing
from the kernel"
Link: https://lore.kernel.org/lkml/201910011140.EA0181F13@keescook/
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
sysctl: Remove the sysctl system call
Paolo Abeni says:
====================
openvswitch: remove a couple of BUG_ON()
The openvswitch kernel datapath includes some BUG_ON() statements to check
for exceptional/unexpected failures. These patches drop a couple of them,
where we can do that without introducing other side effects.
v1 -> v2:
- avoid memory leaks on error path
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If we can't build the flow del notification, we can simply delete
the flow, no need to crash the kernel. Still keep a WARN_ON to
preserve debuggability.
Note: the BUG_ON() predates the Fixes tag, but this change
can be applied only after the mentioned commit.
v1 -> v2:
- do not leak an skb on error
Fixes: aed067783e ("openvswitch: Minimize ovs_flow_cmd_del critical section.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the callers of ovs_flow_cmd_build_info() already deal with
error return code correctly, so we can handle the error condition
in a more gracefull way. Still dump a warning to preserve
debuggability.
v1 -> v2:
- clarify the commit message
- clean the skb and report the error (DaveM)
Fixes: ccb1352e76 ("net: Add Open vSwitch kernel components.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported [0] that since the referenced commit a warning is
triggered in phylib that complains about paged operations being used
with a PHY driver that doesn't support this. The commit isn't wrong,
just for one chip version (RTL8105e) no dedicated PHY driver exists
yet. So add the missing PHY driver.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 3a129e3f9a ("r8169: switch to phylib functions in more places")
Reported-by: jhdskag3 <jhdskag3@tutanota.com>
Tested-by: jhdskag3 <jhdskag3@tutanota.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was reported [0] that network doesn't wake up on cable plug-in with
certain chip versions. Reason is that on these chip versions the PHY
doesn't detect cable plug-in when being in power-down mode. So prevent
the PHY from powering down if WoL is enabled.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=202103
Fixes: 95fb8bb318 ("net: phy: force phy suspend when calling phy_stop")
Reported-by: jhdskag3 <jhdskag3@tutanota.com>
Tested-by: jhdskag3 <jhdskag3@tutanota.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alan reported [0] that network is broken since the referenced commit
when using jumbo frames. This commit isn't wrong, it just revealed
another issue that has been existing before. According to the vendor
driver the RTL8168e-specific jumbo config doesn't apply for RTL8168evl.
[0] https://lkml.org/lkml/2019/11/30/119
Fixes: 4ebcb113ed ("r8169: fix jumbo packet handling on resume from suspend")
Reported-by: Alan J. Wylie <alan@wylie.me.uk>
Tested-by: Alan J. Wylie <alan@wylie.me.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a block device supports rw_page operation, it doesn't submit bios so
the annotation in submit_bio() for refault stall doesn't work. It
happens with zram in android, especially swap read path which could
consume CPU cycle for decompress. It is also a problem for zswap which
uses frontswap.
Annotate swap_readpage() to account the synchronous IO overhead to
prevent underreport memory pressure.
[akpm@linux-foundation.org: add comment, per Johannes]
Link: http://lkml.kernel.org/r/20191010152134.38545-1-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Seth Jennings <sjenning@redhat.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In 64bit system. sb->s_maxbytes of shmem filesystem is MAX_LFS_FILESIZE,
which equal LLONG_MAX.
If offset > LLONG_MAX - PAGE_SIZE, offset + len < LLONG_MAX in
shmem_fallocate, which will pass the checking in vfs_fallocate.
/* Check for wrap through zero too */
if (((offset + len) > inode->i_sb->s_maxbytes) || ((offset + len) < 0))
return -EFBIG;
loff_t unmap_start = round_up(offset, PAGE_SIZE) in shmem_fallocate
causes a overflow.
Syzkaller reports a overflow problem in mm/shmem:
UBSAN: Undefined behaviour in mm/shmem.c:2014:10
signed integer overflow: '9223372036854775807 + 1' cannot be represented in type 'long long int'
CPU: 0 PID:17076 Comm: syz-executor0 Not tainted 4.1.46+ #1
Hardware name: linux, dummy-virt (DT)
Call trace:
dump_backtrace+0x0/0x2c8 arch/arm64/kernel/traps.c:100
show_stack+0x20/0x30 arch/arm64/kernel/traps.c:238
__dump_stack lib/dump_stack.c:15 [inline]
ubsan_epilogue+0x18/0x70 lib/ubsan.c:164
handle_overflow+0x158/0x1b0 lib/ubsan.c:195
shmem_fallocate+0x6d0/0x820 mm/shmem.c:2104
vfs_fallocate+0x238/0x428 fs/open.c:312
SYSC_fallocate fs/open.c:335 [inline]
SyS_fallocate+0x54/0xc8 fs/open.c:239
The highest bit of unmap_start will be appended with sign bit 1
(overflow) when calculate shmem_falloc.start:
shmem_falloc.start = unmap_start >> PAGE_SHIFT.
Fix it by casting the type of unmap_start to u64, when right shifted.
This bug is found in LTS Linux 4.1. It also seems to exist in mainline.
Link: http://lkml.kernel.org/r/1573867464-5107-1-git-send-email-chenjun102@huawei.com
Signed-off-by: Chen Jun <chenjun102@huawei.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The shmem_writepage() uses GFP_ATOMIC to allocate swap cache. GFP_ATOMIC
used to mean __GFP_HIGH, but now it means __GFP_HIGH | __GFP_ATOMIC |
__GFP_KSWAPD_RECLAIM. However, shmem_writepage() should write out to swap
only in response to memory pressure, so __GFP_KSWAPD_RECLAIM looks useless
since the caller may be kswapd itself or in direct reclaim already.
In addition, XArray node allocations from PF_MEMALLOC contexts could
completely exhaust the page allocator, __GFP_NOMEMALLOC stops emergency
reserves from being allocated.
Here just copy the gfp flags used by add_to_swap().
Hugh:
"a cleanup to make the two calls look the same when they don't need to
be different (whereas the call from __read_swap_cache_async() rightly
uses a lower priority gfp)".
Link: http://lkml.kernel.org/r/1572991351-86061-1-git-send-email-yang.shi@linux.alibaba.com
Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
