[WHY]
Hot plugging and then hot unplugging leads to k1 and k2 values to
change, as signal is detected as a virtual signal on hot unplug. Writing
these values to OTG_PIXEL_RATE_DIV register might cause primary display
to blank (known hw bug).
[HOW]
No longer write k1 and k2 values to register if signal is virtual, we
have safe guards in place in the case that k1 and k2 is unassigned so
that an unknown value is not written to the register either.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The VCN firmware loading path enables the indirect SRAM mode if it's
advertised as supported. We might have some cases of FW issues that
prevents this mode to working properly though, ending-up in a failed
probe. An example below, observed in the Steam Deck:
[...]
[drm] failed to load ucode VCN0_RAM(0x3A)
[drm] psp gfx command LOAD_IP_FW(0x6) failed and response status is (0xFFFF0000)
amdgpu 0000:04:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring vcn_dec_0 test failed (-110)
[drm:amdgpu_device_init.cold [amdgpu]] *ERROR* hw_init of IP block <vcn_v3_0> failed -110
amdgpu 0000:04:00.0: amdgpu: amdgpu_device_ip_init failed
amdgpu 0000:04:00.0: amdgpu: Fatal error during GPU init
[...]
Disabling the VCN block circumvents this, but it's a very invasive
workaround that turns off the entire feature. So, let's add a quirk
on VCN loading that checks for known problematic BIOSes on Vangogh,
so we can proactively disable the indirect SRAM mode and allow the
HW proper probe and VCN IP block to work fine.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2385
Fixes: 82132ecc54 ("drm/amdgpu: enable Vangogh VCN indirect sram mode")
Cc: stable@vger.kernel.org
Cc: James Zhu <James.Zhu@amd.com>
Cc: Leo Liu <leo.liu@amd.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When FB_DAMAGE_CLIPS are provided in a non-MPO scenario, the loop does
not use the counter i. This causes the fill_dc_dity_rect() to always
fill dirty_rects[0], causing graphical artifacts when a damage clip
aware DRM client sends more than 1 damage clip.
Instead, use the flip_addrs->dirty_rect_count which is incremented by
fill_dc_dirty_rect() on a successful fill.
Fixes: 30ebe41582 ("drm/amd/display: add FB_DAMAGE_CLIPS support")
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2453
Signed-off-by: Benjamin Cheng <ben@bcheng.me>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.1.x
Some amd asics having reliable hotplug support don't call
drm_kms_helper_poll_init in driver init sequence. However,
due to the unified suspend/resume path for all asics, because
the output_poll_work->func is not set for these asics, a warning
arrives when suspending.
[ 90.656049] <TASK>
[ 90.656050] ? console_unlock+0x4d/0x100
[ 90.656053] ? __irq_work_queue_local+0x27/0x60
[ 90.656056] ? irq_work_queue+0x2b/0x50
[ 90.656057] ? __wake_up_klogd+0x40/0x60
[ 90.656059] __cancel_work_timer+0xed/0x180
[ 90.656061] drm_kms_helper_poll_disable.cold+0x1f/0x2c [drm_kms_helper]
[ 90.656072] amdgpu_device_suspend+0x81/0x170 [amdgpu]
[ 90.656180] amdgpu_pmops_runtime_suspend+0xb5/0x1b0 [amdgpu]
[ 90.656269] pci_pm_runtime_suspend+0x61/0x1b0
drm_kms_helper_poll_enable/disable is valid when poll_init is called in
amdgpu code, which is only used in non DC path. So move such codes into
non-DC path code to get rid of such warnings.
v1: introduce use_kms_poll flag in amdgpu as the poll stuff check
v2: use dc_enabled as the flag to simply code
v3: move code into non DC path instead of relying on any flag
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2411
Fixes: a4e771729a ("drm/probe_helper: sort out poll_running vs poll_enabled")
Reported-by: Bert Karwatzki <spasswolf@web.de>
Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
On resume some displays are not ready for HDCP, so they will fail if we
start the hdcp authentintication too soon.
Add a delay so that the displays can be ready before we start.
NOTE: Previoulsy this delay was set to 3 seconds but it was causing
issues with compliance, 2 seconds should enough for compliance and the
s3 resume case.
[How]
Change the Delay to 2 seconds.
Reviewed-by: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kgd_mem pointers returned by kfd_process_device_translate_handle are
only guaranteed to be valid while p->mutex is held. As soon as the mutex
is unlocked, another thread can free the BO.
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Always setup overdrive tables after resume. Preserve only some
user-defined settings in user_overdrive_table if they're set.
Copy restored user_overdrive_table into od_table to get correct
values.
On cold boot, BTC was triggered and GfxVfCurve was calibrated. We
got VfCurve settings (a). On resuming back, BTC will be triggered
again and GfxVfCurve will be recalibrated. VfCurve settings (b)
got may be different from those of cold boot. So if we reuse
those VfCurve settings (a) got on cold boot on suspend, we can
run into discrepencies.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1897
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2276
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Błażej Szczygieł <mumei6102@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
During miration to vram prange->offset is valid after vram buffer is located,
either use old one or allocate a new one. Move svm_range_vram_node_new before
migrate for each vma to get valid prange->offset.
v2: squash in warning fix
Fixes: b4ee960637 ("drm/amdkfd: Fix BO offset for multi-VMA page migration")
Signed-off-by: Xiaogang Chen <Xiaogang.Chen@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
svm_migrate_ram_to_vram migrates a prange from sys ram to vram. The prange may
cross multiple vma. Need remember current dst vram offset in the TTM resource for
each migration.
v2: squash in warning fix (Alex)
Signed-off-by: Xiaogang Chen <Xiaogang.Chen@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull tpm fixes from Jarkko Sakkinen:
"Two additional bug fixes for v6.3"
* tag 'tpm-v6.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jarkko/linux-tpmdd:
tpm: disable hwrng for fTPM on some AMD designs
tpm/eventlog: Don't abort tpm_read_log on faulty ACPI address
AMD has issued an advisory indicating that having fTPM enabled in
BIOS can cause "stuttering" in the OS. This issue has been fixed
in newer versions of the fTPM firmware, but it's up to system
designers to decide whether to distribute it.
This issue has existed for a while, but is more prevalent starting
with kernel 6.1 because commit b006c439d5 ("hwrng: core - start
hwrng kthread also for untrusted sources") started to use the fTPM
for hwrng by default. However, all uses of /dev/hwrng result in
unacceptable stuttering.
So, simply disable registration of the defective hwrng when detecting
these faulty fTPM versions. As this is caused by faulty firmware, it
is plausible that such a problem could also be reproduced by other TPM
interactions, but this hasn't been shown by any user's testing or reports.
It is hypothesized to be triggered more frequently by the use of the RNG
because userspace software will fetch random numbers regularly.
Intentionally continue to register other TPM functionality so that users
that rely upon PCR measurements or any storage of data will still have
access to it. If it's found later that another TPM functionality is
exacerbating this problem a module parameter it can be turned off entirely
and a module parameter can be introduced to allow users who rely upon
fTPM functionality to turn it on even though this problem is present.
Link: https://www.amd.com/en/support/kb/faq/pa-410
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216989
Link: https://lore.kernel.org/all/20230209153120.261904-1-Jason@zx2c4.com/
Fixes: b006c439d5 ("hwrng: core - start hwrng kthread also for untrusted sources")
Cc: stable@vger.kernel.org
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: James Bottomley <James.Bottomley@hansenpartnership.com>
Tested-by: reach622@mailcuk.com
Tested-by: Bell <1138267643@qq.com>
Co-developed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Pull xfs fixes from Darrick Wong:
- Fix a crash if mount time quotacheck fails when there are inodes
queued for garbage collection.
- Fix an off by one error when discarding folios after writeback
failure.
* tag 'xfs-6.3-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix off-by-one-block in xfs_discard_folio()
xfs: quotacheck failure can race with background inode inactivation
Pull staging driver fixes and removal from Greg KH:
"Here are four small staging driver fixes, and one big staging driver
deletion for 6.3-rc2.
The fixes are:
- rtl8192e driver fixes for where the driver was attempting to
execute various programs directly from the disk for unknown reasons
- rtl8723bs driver fixes for issues found by Hans in testing
The deleted driver is the removal of the r8188eu wireless driver as
now in 6.3-rc1 we have a "real" wifi driver for one that includes
support for many many more devices than this old driver did. So it's
time to remove it as it is no longer needed. The maintainers of this
driver all have acked its removal. Many thanks to them over the years
for working to clean it up and keep it working while the real driver
was being developed.
All of these have been in linux-next this week with no reported
problems"
* tag 'staging-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8188eu: delete driver
staging: rtl8723bs: Pass correct parameters to cfg80211_get_bss()
staging: rtl8723bs: Fix key-store index handling
staging: rtl8192e: Remove call_usermodehelper starting RadioPower.sh
staging: rtl8192e: Remove function ..dm_check_ac_dc_power calling a script
Pull x86 fix from Borislav Petkov:
"A single erratum fix for AMD machines:
- Disable XSAVES on AMD Zen1 and Zen2 machines due to an erratum. No
impact to anything as those machines will fallback to XSAVEC which
is equivalent there"
* tag 'x86_urgent_for_v6.3_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Disable XSAVES on AMD family 0x17
Pull clone3 fix from Christian Brauner:
"A simple fix for the clone3() system call.
The CLONE_NEWTIME allows the creation of time namespaces. The flag
reuses a bit from the CSIGNAL bits that are used in the legacy clone()
system call to set the signal that gets sent to the parent after the
child exits.
The clone3() system call doesn't rely on CSIGNAL anymore as it uses a
dedicated .exit_signal field in struct clone_args. So we blocked all
CSIGNAL bits in clone3_args_valid(). When CLONE_NEWTIME was introduced
and reused a CSIGNAL bit we forgot to adapt clone3_args_valid()
causing CLONE_NEWTIME with clone3() to be rejected. Fix this"
* tag 'kernel.fork.v6.3-rc2' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux:
selftests/clone3: test clone3 with CLONE_NEWTIME
fork: allow CLONE_NEWTIME in clone3 flags
Pull vfs fixes from Christian Brauner:
- When allocating pages for a watch queue failed, we didn't return an
error causing userspace to proceed even though all subsequent
notifcations would be lost. Make sure to return an error.
- Fix a misformed tree entry for the idmapping maintainers entry.
- When setting file leases from an idmapped mount via
generic_setlease() we need to take the idmapping into account
otherwise taking a lease would fail from an idmapped mount.
- Remove two redundant assignments, one in splice code and the other in
locks code, that static checkers complained about.
* tag 'vfs.misc.v6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/idmapping:
filelocks: use mount idmapping for setlease permission check
fs/locks: Remove redundant assignment to cmd
splice: Remove redundant assignment to ret
MAINTAINERS: repair a malformed T: entry in IDMAPPED MOUNTS
watch_queue: fix IOC_WATCH_QUEUE_SET_SIZE alloc error paths
Pull ext4 fixes from Ted Ts'o:
"Bug fixes and regressions for ext4, the most serious of which is a
potential deadlock during directory renames that was introduced during
the merge window discovered by a combination of syzbot and lockdep"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: zero i_disksize when initializing the bootloader inode
ext4: make sure fs error flag setted before clear journal error
ext4: commit super block if fs record error when journal record without error
ext4, jbd2: add an optimized bmap for the journal inode
ext4: fix WARNING in ext4_update_inline_data
ext4: move where set the MAY_INLINE_DATA flag is set
ext4: Fix deadlock during directory rename
ext4: Fix comment about the 64BIT feature
docs: ext4: modify the group desc size to 64
ext4: fix another off-by-one fsmap error on 1k block filesystems
ext4: fix RENAME_WHITEOUT handling for inline directories
ext4: make kobj_type structures constant
ext4: fix cgroup writeback accounting with fs-layer encryption
The cpumask_check() was unnecessarily tight, and causes problems for the
users of cpumask_next().
We have a number of users that take the previous return value of one of
the bit scanning functions and subtract one to keep it in "range". But
since the scanning functions end up returning up to 'small_cpumask_bits'
instead of the tighter 'nr_cpumask_bits', the range really needs to be
using that widened form.
[ This "previous-1" behavior is also the reason we have all those
comments about /* -1 is a legal arg here. */ and separate checks for
that being ok. So we could have just made "small_cpumask_bits-1"
be a similar special "don't check this" value.
Tetsuo Handa even suggested a patch that only does that for
cpumask_next(), since that seems to be the only actual case that
triggers, but that all makes it even _more_ magical and special. So
just relax the check ]
One example of this kind of pattern being the 'c_start()' function in
arch/x86/kernel/cpu/proc.c, but also duplicated in various forms on
other architectures.
Reported-by: syzbot+96cae094d90877641f32@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=96cae094d90877641f32
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Link: https://lore.kernel.org/lkml/c1f4cc16-feea-b83c-82cf-1a1f007b7eb9@I-love.SAKURA.ne.jp/
Fixes: 596ff4a09b ("cpumask: re-introduce constant-sized cpumask optimizations")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c updates from Wolfram Sang:
"This marks the end of a transition to let I2C have the same probe
semantics as other subsystems. Uwe took care that no drivers in the
current tree nor in -next use the deprecated .probe call. So, it is a
good time to switch to the new, standard semantics now.
There is also a regression fix:
- regression fix for the notifier handling of the I2C core
- final coversions of drivers away from deprecated .probe
- make .probe_new the standard probe and convert I2C core to use it
* tag 'i2c-for-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: dev: Fix bus callback return values
i2c: Convert drivers to new .probe() callback
i2c: mux: Convert all drivers to new .probe() callback
i2c: Switch .probe() to not take an id parameter
media: i2c: ov2685: convert to i2c's .probe_new()
media: i2c: ov5695: convert to i2c's .probe_new()
w1: ds2482: Convert to i2c's .probe_new()
serial: sc16is7xx: Convert to i2c's .probe_new()
mtd: maps: pismo: Convert to i2c's .probe_new()
misc: ad525x_dpot-i2c: Convert to i2c's .probe_new()
If the boot loader inode has never been used before, the
EXT4_IOC_SWAP_BOOT inode will initialize it, including setting the
i_size to 0. However, if the "never before used" boot loader has a
non-zero i_size, then i_disksize will be non-zero, and the
inconsistency between i_size and i_disksize can trigger a kernel
warning:
WARNING: CPU: 0 PID: 2580 at fs/ext4/file.c:319
CPU: 0 PID: 2580 Comm: bb Not tainted 6.3.0-rc1-00004-g703695902cfa
RIP: 0010:ext4_file_write_iter+0xbc7/0xd10
Call Trace:
vfs_write+0x3b1/0x5c0
ksys_write+0x77/0x160
__x64_sys_write+0x22/0x30
do_syscall_64+0x39/0x80
Reproducer:
1. create corrupted image and mount it:
mke2fs -t ext4 /tmp/foo.img 200
debugfs -wR "sif <5> size 25700" /tmp/foo.img
mount -t ext4 /tmp/foo.img /mnt
cd /mnt
echo 123 > file
2. Run the reproducer program:
posix_memalign(&buf, 1024, 1024)
fd = open("file", O_RDWR | O_DIRECT);
ioctl(fd, EXT4_IOC_SWAP_BOOT);
write(fd, buf, 1024);
Fix this by setting i_disksize as well as i_size to zero when
initiaizing the boot loader inode.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217159
Cc: stable@kernel.org
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Link: https://lore.kernel.org/r/20230308032643.641113-1-chengzhihao1@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Now, 'es->s_state' maybe covered by recover journal. And journal errno
maybe not recorded in journal sb as IO error. ext4_update_super() only
update error information when 'sbi->s_add_error_count' large than zero.
Then 'EXT4_ERROR_FS' flag maybe lost.
To solve above issue just recover 'es->s_state' error flag after journal
replay like error info.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Baokun Li <libaokun1@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230307061703.245965-2-yebin@huaweicloud.com
The only caller of ext4_find_inline_data_nolock() that needs setting of
EXT4_STATE_MAY_INLINE_DATA flag is ext4_iget_extra_inode(). In
ext4_write_inline_data_end() we just need to update inode->i_inline_off.
Since we are going to add one more caller that does not need to set
EXT4_STATE_MAY_INLINE_DATA, just move setting of EXT4_STATE_MAY_INLINE_DATA
out to ext4_iget_extra_inode().
Signed-off-by: Ye Bin <yebin10@huawei.com>
Cc: stable@kernel.org
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20230307015253.2232062-2-yebin@huaweicloud.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Pull SCSI fixes from James Bottomley:
"Twenty fixes all in drivers except the one zone storage revalidation
fix to sd.
The megaraid_sas fixes are more on the level of a driver update
(enabling crash dump and increasing lun number) but I thought you
could let this slide on -rc1 and the next most extensive update is a
load of fixes to mpi3mr"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Fix wrong zone_write_granularity value during revalidate
scsi: storvsc: Handle BlockSize change in Hyper-V VHD/VHDX file
scsi: megaraid_sas: Driver version update to 07.725.01.00-rc1
scsi: megaraid_sas: Add crash dump mode capability bit in MFI capabilities
scsi: megaraid_sas: Update max supported LD IDs to 240
scsi: mpi3mr: Bad drive in topology results kernel crash
scsi: mpi3mr: NVMe command size greater than 8K fails
scsi: mpi3mr: Return proper values for failures in firmware init path
scsi: mpi3mr: Wait for diagnostic save during controller init
scsi: mpi3mr: Driver unload crashes host when enhanced logging is enabled
scsi: mpi3mr: ioctl timeout when disabling/enabling interrupt
scsi: lpfc: Avoid usage of list iterator variable after loop
scsi: lpfc: Check kzalloc() in lpfc_sli4_cgn_params_read()
scsi: ufs: mcq: qcom: Clean the return path of ufs_qcom_mcq_config_resource()
scsi: ufs: mcq: qcom: Fix passing zero to PTR_ERR
scsi: ufs: ufs-qcom: Remove impossible check
scsi: ufs: core: Add soft dependency on governor_simpleondemand
scsi: hisi_sas: Check devm_add_action() return value
scsi: qla2xxx: Add option to disable FC2 Target support
scsi: target: iscsi: Fix an error message in iscsi_check_key()
Pull block fixes from Jens Axboe:
- Fix a regression in exclusive mode handling of the partition code,
introduced in this merge windoe (Yu)
- Fix for a use-after-free in BFQ (Yu)
- Add sysfs documentation for the 'hidden' attribute (Sagi)
* tag 'block-6.3-2023-03-09' of git://git.kernel.dk/linux:
block, bfq: fix uaf for 'stable_merge_bfqq'
docs: sysfs-block: document hidden sysfs entry
block: fix wrong mode for blkdev_put() from disk_scan_partitions()
Pull put_and_unmap_page() helper from Al Viro:
"kmap_local_page() conversions in local filesystems keep running into
kunmap_local_page()+put_page() combinations. We can keep inventing
names for identical inline helpers, but it's getting rather
inconvenient. I've added a trivial helper to linux/highmem.h instead.
I would've held that back until the merge window, if not for the mess
it causes in tree topology - I've several branches merging from that
one, and it's only going to get worse if e.g. ext2 stuff gets picked
by Jan"
* tag 'pull-highmem' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
new helper: put_and_unmap_page()
Pull misc fixes from Al Viro:
"pick_file() speculation fix + fix for alpha mis(merge,cherry-pick)
The fs/file.c one is a genuine missing speculation barrier in
pick_file() (reachable e.g. via close(2)). The alpha one is strictly
speaking not a bug fix, but only because confusion between
preempt_enable() and preempt_disable() is harmless on architecture
without CONFIG_PREEMPT.
Looks like alpha.git picked the wrong version of patch - that braino
used to be there in early versions, but it had been fixed quite a
while ago..."
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: prevent out-of-bounds array speculation when closing a file descriptor
alpha: fix lazy-FPU mis(merged/applied/whatnot)
Pull thermal control fix from Rafael Wysocki:
"Fix a recently introduced deadlock in the int340x thermal control
driver (Srinivas Pandruvada)"
* tag 'thermal-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: intel: int340x: processor_thermal: Fix deadlock
Pull RISC-V fixes from Palmer Dabbelt:
- RISC-V architecture-specific ELF attributes have been disabled in the
kernel builds
- A fix for a locking failure while during errata patching that
manifests on SiFive-based systems
- A fix for a KASAN failure during stack unwinding
- A fix for some lockdep failures during text patching
* tag 'riscv-for-linus-6.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Don't check text_mutex during stop_machine
riscv: Use READ_ONCE_NOCHECK in imprecise unwinding stack mode
RISC-V: fix taking the text_mutex twice during sifive errata patching
RISC-V: Stop emitting attributes
Pull drm fixes from Dave Airlie:
"Weekly fixes.
msm and amdgpu are the vast majority of these, otherwise some
straggler misc from last week for nouveau and cirrus and a mailmap
update for a drm developer.
mailmap:
- add an entry
nouveau:
- fix system shutdown regression
- build warning fix
cirrus:
- NULL ptr deref fix
msm:
- fix invalid ptr free in syncobj cleanup
- sync GMU removal in teardown
- a5xx preemption fixes
- fix runpm imbalance
- DPU hw fixes
- stack corruption fix
- clear DSPP reservation
amdgpu:
- Misc display fixes
- UMC 8.10 fixes
- Driver unload fixes
- NBIO 7.3.0 fix
- Error checking fixes for soc15, nv, soc21 read register interface
- Fix video cap query for VCN 4.0.4
amdkfd:
- Fix return check in doorbell handling"
* tag 'drm-fixes-2023-03-10' of git://anongit.freedesktop.org/drm/drm: (42 commits)
drm/amdgpu/soc21: Add video cap query support for VCN_4_0_4
drm/amdgpu: fix error checking in amdgpu_read_mm_registers for nv
drm/amdgpu: fix error checking in amdgpu_read_mm_registers for soc21
drm/amdgpu: fix error checking in amdgpu_read_mm_registers for soc15
drm/amdgpu: Fix the warning info when removing amdgpu device
drm/amdgpu: fix return value check in kfd
drm/amd: Fix initialization mistake for NBIO 7.3.0
drm/amdgpu: Fix call trace warning and hang when removing amdgpu device
mailmap: add mailmap entries for Faith.
drm/msm: DEVFREQ_GOV_SIMPLE_ONDEMAND is no longer needed
drm/amd/display: Update clock table to include highest clock setting
drm/amd/pm: Enable ecc_info table support for smu v13_0_10
drm/amdgpu: Support umc node harvest config on umc v8_10
drm/connector: print max_requested_bpc in state debugfs
drm/display: Don't block HDR_OUTPUT_METADATA on unknown EOTF
drm/msm/dpu: clear DSPP reservations in rm release
drm/msm/disp/dpu: fix sc7280_pp base offset
drm/msm/dpu: fix stack smashing in dpu_hw_ctl_setup_blendstage
drm/msm/dpu: don't use DPU_CLK_CTRL_CURSORn for DMA SSPP clocks
drm/msm/dpu: fix clocks settings for msm8998 SSPP blocks
...
Pull erofs fixes from Gao Xiang:
"The most important one reverts an improper fix which can cause an
unexpected warning more often on specific images, and another one
fixes LZMA decompression on 32-bit platforms. The others are minor
fixes and cleanups.
- Fix LZMA decompression failure on HIGHMEM platforms
- Revert an inproper fix since it is actually an implementation issue
of vmalloc()
- Avoid a wrong DBG_BUGON since it could be triggered with -EINTR
- Minor cleanups"
* tag 'erofs-for-6.3-rc2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
erofs: use wrapper i_blocksize() in erofs_file_read_iter()
erofs: get rid of a useless DBG_BUGON
erofs: Revert "erofs: fix kvcalloc() misuse with __GFP_NOFAIL"
erofs: fix wrong kunmap when using LZMA on HIGHMEM platforms
erofs: mark z_erofs_lzma_init/erofs_pcpubuf_init w/ __init
Pull nfsd fixes from Chuck Lever:
- Protect NFSD writes against filesystem freezing
- Fix a potential memory leak during server shutdown
* tag 'nfsd-6.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/cel/linux:
SUNRPC: Fix a server shutdown leak
NFSD: Protect against filesystem freezing
Pull btrfs fixes from David Sterba:
"First batch of fixes. Among them there are two updates to sysfs and
ioctl which are not strictly fixes but are used for testing so there's
no reason to delay them.
- fix block group item corruption after inserting new block group
- fix extent map logging bit not cleared for split maps after
dropping range
- fix calculation of unusable block group space reporting bogus
values due to 32/64b division
- fix unnecessary increment of read error stat on write error
- improve error handling in inode update
- export per-device fsid in DEV_INFO ioctl to distinguish seeding
devices, needed for testing
- allocator size classes:
- fix potential dead lock in size class loading logic
- print sysfs stats for the allocation classes"
* tag 'for-6.3-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix block group item corruption after inserting new block group
btrfs: fix extent map logging bit not cleared for split maps after dropping range
btrfs: fix percent calculation for bg reclaim message
btrfs: fix unnecessary increment of read error stat on write error
btrfs: handle btrfs_del_item errors in __btrfs_update_delayed_inode
btrfs: ioctl: return device fsid from DEV_INFO ioctl
btrfs: fix potential dead lock in size class loading logic
btrfs: sysfs: add size class stats
Pull io_uring fixes from Jens Axboe:
- Stop setting PF_NO_SETAFFINITY on io-wq workers.
This has been reported in the past as it confuses some applications,
as some of their threads will fail with -1/EINVAL if attempted
affinitized. Most recent report was on cpusets, where enabling that
with io-wq workers active will fail.
Just deal with the mask changing by checking when a worker times out,
and then exit if we have no work pending.
- Fix an issue with passthrough support where we don't properly check
if the file type has pollable uring_cmd support.
- Fix a reported W=1 warning on a variable being set and unused. Add a
special helper for iterating these lists that doesn't save the
previous list element, if that iterator never ends up using it.
* tag 'io_uring-6.3-2023-03-09' of git://git.kernel.dk/linux:
io_uring: silence variable ‘prev’ set but not used warning
io_uring/uring_cmd: ensure that device supports IOPOLL
io_uring/io-wq: stop setting PF_NO_SETAFFINITY on io-wq workers
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Add Adrian Hunter to MAINTAINERS as a perf tools reviewer
- Sync various tools/ copies of kernel headers with the kernel sources,
this time trying to avoid first merging with upstream to then update
but instead copy from upstream so that a merge is avoided and the end
result after merging this pull request is the one expected,
tools/perf/check-headers.sh (mostly) happy, less warnings while
building tools/perf/
- Fix counting when initial delay configured by setting
perf_attr.enable_on_exec when starting workloads from the perf
command line
- Don't avoid emitting a PERF_RECORD_MMAP2 in 'perf inject
--buildid-all' when that record comes with a build-id, otherwise we
end up not being able to resolve symbols
- Don't use comma as the CSV output separator the "stat+csv_output"
test, as comma can appear on some tests as a modifier for an event,
use @ instead, ditto for the JSON linter test
- The offcpu test was looking for some bits being set on
task_struct->prev_state without masking other bits not important for
this specific 'perf test', fix it
* tag 'perf-tools-fixes-for-v6.3-1-2023-03-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf tools: Add Adrian Hunter to MAINTAINERS as a reviewer
tools headers UAPI: Sync linux/perf_event.h with the kernel sources
tools headers x86 cpufeatures: Sync with the kernel sources
tools include UAPI: Sync linux/vhost.h with the kernel sources
tools arch x86: Sync the msr-index.h copy with the kernel sources
tools headers kvm: Sync uapi/{asm/linux} kvm.h headers with the kernel sources
tools include UAPI: Synchronize linux/fcntl.h with the kernel sources
tools headers: Synchronize {linux,vdso}/bits.h with the kernel sources
tools headers UAPI: Sync linux/prctl.h with the kernel sources
tools headers: Update the copy of x86's mem{cpy,set}_64.S used in 'perf bench'
perf stat: Fix counting when initial delay configured
tools headers svm: Sync svm headers with the kernel sources
perf test: Avoid counting commas in json linter
perf tests stat+csv_output: Switch CSV separator to @
perf inject: Fix --buildid-all not to eat up MMAP2
tools arch x86: Sync the msr-index.h copy with the kernel sources
perf test: Fix offcpu test prev_state check
