Assigning a non-standard brightness value to an LED can cause the value
to slowly drift downward over time as the effects of integer division
accumulate. Each time that an LED is triggered, a series of set and get
calls occur. For example, if we assume a tablet with max_hlv = 100, then
when brightness is set to "200" through sysfs, the hlv value written to
hardware will be `200*100/255 = 78`. If the LED trigger is later activated,
the hlv value will be used to determine the brightness: `78*255/100 = 198`.
This lower brightness then used to set the brightness of the next LED.
However, `198*100/255 = 77`, so the next LED ends up slightly dimmer.
Each subsequent trigger activation will cause the brightness to continue
drifting down until we reach a point where the result of integer divsion
does not introduce any new error.
This commit corrects the issue by being more careful about how we handle
scaling between the two ranges (0..max_{h,l}lv) and (0..LED_FULL).
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Pull HID fixes from Benjamin Tissoires:
- regression fix in suspend/resume for i2c-hid (Kenny Levinsen)
- fix wacom driver assuming a name can not be null (WangYuli)
- a couple of constify changes/fixes (Thomas Weißschuh)
- a couple of selftests/hid fixes (Maximilian Heyne & Benjamin
Tissoires)
* tag 'hid-for-linus-2024120501' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
selftests/hid: fix kfunc inclusions with newer bpftool
HID: bpf: drop unneeded casts discarding const
HID: bpf: constify hid_ops
selftests: hid: fix typo and exit code
HID: wacom: fix when get product name maybe null pointer
HID: i2c-hid: Revert to using power commands to wake on resume
Pull watchdog updates from Wim Van Sebroeck:
- Add support for exynosautov920 SoC
- Add support for Airoha EN7851 watchdog
- Add support for MT6735 TOPRGU/WDT
- Delete the cpu5wdt driver
- Always print when registering watchdog fails
- Several other small fixes and improvements
* tag 'linux-watchdog-6.13-rc1' of git://www.linux-watchdog.org/linux-watchdog: (36 commits)
watchdog: rti: of: honor timeout-sec property
watchdog: s3c2410_wdt: add support for exynosautov920 SoC
dt-bindings: watchdog: Document ExynosAutoV920 watchdog bindings
watchdog: mediatek: Add support for MT6735 TOPRGU/WDT
watchdog: mediatek: Make sure system reset gets asserted in mtk_wdt_restart()
dt-bindings: watchdog: fsl-imx-wdt: Add missing 'big-endian' property
dt-bindings: watchdog: Document Qualcomm QCS8300
docs: ABI: Fix spelling mistake in pretimeout_avaialable_governors
Revert "watchdog: s3c2410_wdt: use exynos_get_pmu_regmap_by_phandle() for PMU regs"
watchdog: rzg2l_wdt: Power on the watchdog domain in the restart handler
watchdog: Switch back to struct platform_driver::remove()
watchdog: it87_wdt: add PWRGD enable quirk for Qotom QCML04
watchdog: da9063: Remove __maybe_unused notations
watchdog: da9063: Do not use a global variable
watchdog: Delete the cpu5wdt driver
watchdog: Add support for Airoha EN7851 watchdog
dt-bindings: watchdog: airoha: document watchdog for Airoha EN7581
watchdog: sl28cpld_wdt: don't print out if registering watchdog fails
watchdog: rza_wdt: don't print out if registering watchdog fails
watchdog: rti_wdt: don't print out if registering watchdog fails
...
Pull LoongArch fixes from Huacai Chen:
"Fix bugs about EFI screen info, hugetlb pte clear and Lockdep-RCU
splat in KVM, plus some trival cleanups"
* tag 'loongarch-fixes-6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: KVM: Protect kvm_io_bus_{read,write}() with SRCU
LoongArch: KVM: Protect kvm_check_requests() with SRCU
LoongArch: BPF: Adjust the parameter of emit_jirl()
LoongArch: Add architecture specific huge_pte_clear()
LoongArch/irq: Use seq_put_decimal_ull_width() for decimal values
LoongArch: Fix reserving screen info memory for above-4G firmware
Pull btrfs fixes from David Sterba:
- add lockdep annotations for io_uring/encoded read integration, inode
lock is held when returning to userspace
- properly reflect experimental config option to sysfs
- handle NULL root in case the rescue mode accepts invalid/damaged tree
roots (rescue=ibadroot)
- regression fix of a deadlock between transaction and extent locks
- fix pending bio accounting bug in encoded read ioctl
- fix NOWAIT mode when checking references for NOCOW files
- fix use-after-free in a rb-tree cleanup in ref-verify debugging tool
* tag 'for-6.13-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix lockdep warnings on io_uring encoded reads
btrfs: ref-verify: fix use-after-free after invalid ref action
btrfs: add a sanity check for btrfs root in btrfs_search_slot()
btrfs: don't loop for nowait writes when checking for cross references
btrfs: sysfs: advertise experimental features only if CONFIG_BTRFS_EXPERIMENTAL=y
btrfs: fix deadlock between transaction commits and extent locks
btrfs: fix use-after-free in btrfs_encoded_read_endio()
Pull quota and udf fixes from Jan Kara:
"Two small UDF fixes for better handling of corrupted filesystem and a
quota fix to fix handling of filesystem freezing"
* tag 'fs_for_v6.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Verify inode link counts before performing rename
udf: Skip parent dir link count update if corrupted
quota: flush quota_release_work upon quota writeback
Pull xfs fixes from Carlos Maiolino:
- Use xchg() in xlog_cil_insert_pcp_aggregate()
- Fix ABBA deadlock on a race between mount and log shutdown
- Fix quota softlimit incoherency on delalloc
- Fix sparse inode limits on runt AG
- remove unknown compat feature checks in SB write valdation
- Eliminate a lockdep false positive
* tag 'xfs-fixes-6.13-rc2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: don't call xfs_bmap_same_rtgroup in xfs_bmap_add_extent_hole_delay
xfs: Use xchg() in xlog_cil_insert_pcp_aggregate()
xfs: prevent mount and log shutdown race
xfs: delalloc and quota softlimit timers are incoherent
xfs: fix sparse inode limits on runt AG
xfs: remove unknown compat feature check in superblock write validation
xfs: eliminate lockdep false positives in xfs_attr_shortform_list
Commit cdd30ebb1b ("module: Convert symbol namespace to string
literal") only converted MODULE_IMPORT_NS() and EXPORT_SYMBOL_NS(),
leaving DEFAULT_SYMBOL_NAMESPACE as a macro expansion.
This commit converts DEFAULT_SYMBOL_NAMESPACE in the same way to avoid
annoyance for the default namespace as well.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts the misconversions introduced by commit cdd30ebb1b
("module: Convert symbol namespace to string literal").
The affected descriptions refer to MODULE_IMPORT_NS() tags in general,
rather than suggesting the use of the empty string ("") as the
namespace.
Fixes: cdd30ebb1b ("module: Convert symbol namespace to string literal")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit cdd30ebb1b ("module: Convert symbol namespace to string
literal"), when MODULE_IMPORT_NS() is missing, 'make nsdeps' inserts
pointless code:
MODULE_IMPORT_NS("ns");
Here, "ns" is not a namespace, but the variable in the semantic patch.
It must not be quoted. Instead, a string literal must be passed to
Coccinelle.
Fixes: cdd30ebb1b ("module: Convert symbol namespace to string literal")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The branch instructions beq, bne, blt, bge, bltu, bgeu and jirl belong
to the format reg2i16, but the sequence of oprand is different for the
instruction jirl. So adjust the parameter order of emit_jirl() to make
it more readable correspond with the Instruction Set Architecture manual.
Here are the instruction formats:
beq rj, rd, offs16
bne rj, rd, offs16
blt rj, rd, offs16
bge rj, rd, offs16
bltu rj, rd, offs16
bgeu rj, rd, offs16
jirl rd, rj, offs16
Link: https://loongson.github.io/LoongArch-Documentation/LoongArch-Vol1-EN.html#branch-instructions
Suggested-by: Huacai Chen <chenhuacai@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
When executing mm selftests run_vmtests.sh, there is such an error:
BUG: Bad page state in process uffd-unit-tests pfn:00000
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x0
flags: 0xffff0000002000(reserved|node=0|zone=0|lastcpupid=0xffff)
raw: 00ffff0000002000 ffffbf0000000008 ffffbf0000000008 0000000000000000
raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
Modules linked in: snd_seq_dummy snd_seq snd_seq_device rfkill vfat fat
virtio_balloon efi_pstore virtio_net pstore net_failover failover fuse
nfnetlink virtio_scsi virtio_gpu virtio_dma_buf dm_multipath efivarfs
CPU: 2 UID: 0 PID: 1913 Comm: uffd-unit-tests Not tainted 6.12.0 #184
Hardware name: QEMU QEMU Virtual Machine, BIOS unknown 2/2/2022
Stack : 900000047c8ac000 0000000000000000 9000000000223a7c 900000047c8ac000
900000047c8af690 900000047c8af698 0000000000000000 900000047c8af7d8
900000047c8af7d0 900000047c8af7d0 900000047c8af5b0 0000000000000001
0000000000000001 900000047c8af698 10b3c7d53da40d26 0000010000000000
0000000000000022 0000000fffffffff fffffffffe000000 ffff800000000000
000000000000002f 0000800000000000 000000017a6d4000 90000000028f8940
0000000000000000 0000000000000000 90000000025aa5e0 9000000002905000
0000000000000000 90000000028f8940 ffff800000000000 0000000000000000
0000000000000000 0000000000000000 9000000000223a94 000000012001839c
00000000000000b0 0000000000000004 0000000000000000 0000000000071c1d
...
Call Trace:
[<9000000000223a94>] show_stack+0x5c/0x180
[<9000000001c3fd64>] dump_stack_lvl+0x6c/0xa0
[<900000000056aa08>] bad_page+0x1a0/0x1f0
[<9000000000574978>] free_unref_folios+0xbf0/0xd20
[<90000000004e65cc>] folios_put_refs+0x1a4/0x2b8
[<9000000000599a0c>] free_pages_and_swap_cache+0x164/0x260
[<9000000000547698>] tlb_batch_pages_flush+0xa8/0x1c0
[<9000000000547f30>] tlb_finish_mmu+0xa8/0x218
[<9000000000543cb8>] exit_mmap+0x1a0/0x360
[<9000000000247658>] __mmput+0x78/0x200
[<900000000025583c>] do_exit+0x43c/0xde8
[<9000000000256490>] do_group_exit+0x68/0x110
[<9000000000256554>] sys_exit_group+0x1c/0x20
[<9000000001c413b4>] do_syscall+0x94/0x130
[<90000000002216d8>] handle_syscall+0xb8/0x158
Disabling lock debugging due to kernel taint
BUG: non-zero pgtables_bytes on freeing mm: -16384
On LoongArch system, invalid huge pte entry should be invalid_pte_table
or a single _PAGE_HUGE bit rather than a zero value. And it should be
the same with invalid pmd entry, since pmd_none() is called by function
free_pgd_range() and pmd_none() return 0 by huge_pte_clear(). So single
_PAGE_HUGE bit is also treated as a valid pte table and free_pte_range()
will be called in free_pmd_range().
free_pmd_range()
pmd = pmd_offset(pud, addr);
do {
next = pmd_addr_end(addr, end);
if (pmd_none_or_clear_bad(pmd))
continue;
free_pte_range(tlb, pmd, addr);
} while (pmd++, addr = next, addr != end);
Here invalid_pte_table is used for both invalid huge pte entry and
pmd entry.
Cc: stable@vger.kernel.org
Fixes: 09cfefb7fa ("LoongArch: Add memory management")
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Performance improvement for reading /proc/interrupts on LoongArch.
On a system with n CPUs and m interrupts, there will be n*m decimal
values yielded via seq_printf(.."%10u "..) which is less efficient than
seq_put_decimal_ull_width(), stress reading /proc/interrupts indicates
~30% performance improvement with this patch (and its friends).
Signed-off-by: David Wang <00107082@163.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Since screen_info.lfb_base is a __u32 type, an above-4G address need an
ext_lfb_base to present its higher 32bits. In init_screen_info() we can
use __screen_info_lfb_base() to handle this case for reserving screen
info memory.
Signed-off-by: Xuefeng Zhao <zhaoxuefeng@loongson.cn>
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Tianyang Zhang <zhangtianyang@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c component probing support from Wolfram Sang:
"Add OF component probing.
Some devices are designed and manufactured with some components having
multiple drop-in replacement options. These components are often
connected to the mainboard via ribbon cables, having the same signals
and pin assignments across all options. These may include the display
panel and touchscreen on laptops and tablets, and the trackpad on
laptops. Sometimes which component option is used in a particular
device can be detected by some firmware provided identifier, other
times that information is not available, and the kernel has to try to
probe each device.
Instead of a delicate dance between drivers and device tree quirks,
this change introduces a simple I2C component probe function. For a
given class of devices on the same I2C bus, it will go through all of
them, doing a simple I2C read transfer and see which one of them
responds. It will then enable the device that responds"
* tag 'i2c-for-6.13-rc1-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
MAINTAINERS: fix typo in I2C OF COMPONENT PROBER
of: base: Document prefix argument for of_get_next_child_with_prefix()
i2c: Fix whitespace style issue
arm64: dts: mediatek: mt8173-elm-hana: Mark touchscreens and trackpads as fail
platform/chrome: Introduce device tree hardware prober
i2c: of-prober: Add GPIO support to simple helpers
i2c: of-prober: Add simple helpers for regulator support
i2c: Introduce OF component probe function
of: base: Add for_each_child_of_node_with_prefix()
of: dynamic: Add of_changeset_update_prop_string
Pull bprintf() removal from Steven Rostedt:
- Remove unused bprintf() function, that was added with the rest of the
"bin-printf" functions.
These are functions that are used by trace_printk() that allows to
quickly save the format and arguments into the ring buffer without
the expensive processing of converting numbers to ASCII. Then on
output, at a much later time, the ring buffer is read and the string
processing occurs then. The bprintf() was added for consistency but
was never used. It can be safely removed.
* tag 'trace-printf-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
printf: Remove unused 'bprintf'
Pull timer fixes from Borislav Petkov:
- Fix a case where posix timers with a thread-group-wide target would
miss signals if some of the group's threads are exiting
- Fix a hang caused by ndelay() calling the wrong delay function
__udelay()
- Fix a wrong offset calculation in adjtimex(2) when using ADJ_MICRO
(microsecond resolution) and a negative offset
* tag 'timers_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-timers: Target group sigqueue to current task only if not exiting
delay: Fix ndelay() spuriously treated as udelay()
ntp: Remove invalid cast in time offset math
Pull irq fixes from Borislav Petkov:
- Move the ->select callback to the correct ops structure in
irq-mvebu-sei to fix some Marvell Armada platforms
- Add a workaround for Hisilicon ITS erratum 162100801 which can cause
some virtual interrupts to get lost
- More platform_driver::remove() conversion
* tag 'irq_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Switch back to struct platform_driver::remove()
irqchip/gicv3-its: Add workaround for hip09 ITS erratum 162100801
irqchip/irq-mvebu-sei: Move misplaced select() callback to SEI CP domain
Pull x86 fixes from Borislav Petkov:
- Add a terminating zero end-element to the array describing AMD CPUs
affected by erratum 1386 so that the matching loop actually
terminates instead of going off into the weeds
- Update the boot protocol documentation to mention the fact that the
preferred address to load the kernel to is considered in the
relocatable kernel case too
- Flush the memory buffer containing the microcode patch after applying
microcode on AMD Zen1 and Zen2, to avoid unnecessary slowdowns
- Make sure the PPIN CPU feature flag is cleared on all CPUs if PPIN
has been disabled
* tag 'x86_urgent_for_v6.13_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Terminate the erratum_1386_microcode array
x86/Documentation: Update algo in init_size description of boot protocol
x86/microcode/AMD: Flush patch buffer mapping after application
x86/mm: Carve out INVLPG inline asm for use by others
x86/cpu: Fix PPIN initialization
The point behind strscpy() was to once and for all avoid all the
problems with 'strncpy()' and later broken "fixed" versions like
strlcpy() that just made things worse.
So strscpy not only guarantees NUL-termination (unlike strncpy), it also
doesn't do unnecessary padding at the destination. But at the same time
also avoids byte-at-a-time reads and writes by _allowing_ some extra NUL
writes - within the size, of course - so that the whole copy can be done
with word operations.
It is also stable in the face of a mutable source string: it explicitly
does not read the source buffer multiple times (so an implementation
using "strnlen()+memcpy()" would be wrong), and does not read the source
buffer past the size (like the mis-design that is strlcpy does).
Finally, the return value is designed to be simple and unambiguous: if
the string cannot be copied fully, it returns an actual negative error,
making error handling clearer and simpler (and the caller already knows
the size of the buffer). Otherwise it returns the string length of the
result.
However, there was one final stability issue that can be important to
callers: the stability of the destination buffer.
In particular, the same way we shouldn't read the source buffer more
than once, we should avoid doing multiple writes to the destination
buffer: first writing a potentially non-terminated string, and then
terminating it with NUL at the end does not result in a stable result
buffer.
Yes, it gives the right result in the end, but if the rule for the
destination buffer was that it is _always_ NUL-terminated even when
accessed concurrently with updates, the final byte of the buffer needs
to always _stay_ as a NUL byte.
[ Note that "final byte is NUL" here is literally about the final byte
in the destination array, not the terminating NUL at the end of the
string itself. There is no attempt to try to make concurrent reads and
writes give any kind of consistent string length or contents, but we
do want to guarantee that there is always at least that final
terminating NUL character at the end of the destination array if it
existed before ]
This is relevant in the kernel for the tsk->comm[] array, for example.
Even without locking (for either readers or writers), we want to know
that while the buffer contents may be garbled, it is always a valid C
string and always has a NUL character at 'comm[TASK_COMM_LEN-1]' (and
never has any "out of thin air" data).
So avoid any "copy possibly non-terminated string, and terminate later"
behavior, and write the destination buffer only once.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull turbostat updates from Len Brown:
- assorted minor bug fixes
- assorted platform specific tweaks
- initial RAPL PSYS (SysWatt) support
* tag 'turbostat-2024.11.30' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: 2024.11.30
tools/power turbostat: Add RAPL psys as a built-in counter
tools/power turbostat: Fix child's argument forwarding
tools/power turbostat: Force --no-perf in --dump mode
tools/power turbostat: Add support for /sys/class/drm/card1
tools/power turbostat: Cache graphics sysfs file descriptors during probe
tools/power turbostat: Consolidate graphics sysfs access
tools/power turbostat: Remove unnecessary fflush() call
tools/power turbostat: Enhance platform divergence description
tools/power turbostat: Add initial support for GraniteRapids-D
tools/power turbostat: Remove PC3 support on Lunarlake
tools/power turbostat: Rename arl_features to lnl_features
tools/power turbostat: Add back PC8 support on Arrowlake
tools/power turbostat: Remove PC7/PC9 support on MTL
tools/power turbostat: Honor --show CPU, even when even when num_cpus=1
tools/power turbostat: Fix trailing '\n' parsing
tools/power turbostat: Allow using cpu device in perf counters on hybrid platforms
tools/power turbostat: Fix column printing for PMT xtal_time counters
tools/power turbostat: fix GCC9 build regression
Pull PCI fix from Bjorn Helgaas:
- When removing a PCI device, only look up and remove a platform device
if there is an associated device node for which there could be a
platform device, to fix a merge window regression (Brian Norris)
* tag 'pci-v6.13-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/pwrctrl: Unregister platform device only if one actually exists
Pull ima fix from Paul Moore:
"One small patch to fix a function parameter / local variable naming
snafu that went up to you in the current merge window"
* tag 'lsm-pr-20241129' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
ima: uncover hidden variable in ima_match_rules()
Pull more block updates from Jens Axboe:
- NVMe pull request via Keith:
- Use correct srcu list traversal (Breno)
- Scatter-gather support for metadata (Keith)
- Fabrics shutdown race condition fix (Nilay)
- Persistent reservations updates (Guixin)
- Add the required bits for MD atomic write support for raid0/1/10
- Correct return value for unknown opcode in ublk
- Fix deadlock with zone revalidation
- Fix for the io priority request vs bio cleanups
- Use the correct unsigned int type for various limit helpers
- Fix for a race in loop
- Cleanup blk_rq_prep_clone() to prevent uninit-value warning and make
it easier for actual humans to read
- Fix potential UAF when iterating tags
- A few fixes for bfq-iosched UAF issues
- Fix for brd discard not decrementing the allocated page count
- Various little fixes and cleanups
* tag 'block-6.13-20242901' of git://git.kernel.dk/linux: (36 commits)
brd: decrease the number of allocated pages which discarded
block, bfq: fix bfqq uaf in bfq_limit_depth()
block: Don't allow an atomic write be truncated in blkdev_write_iter()
mq-deadline: don't call req_get_ioprio from the I/O completion handler
block: Prevent potential deadlock in blk_revalidate_disk_zones()
block: Remove extra part pointer NULLify in blk_rq_init()
nvme: tuning pr code by using defined structs and macros
nvme: introduce change ptpl and iekey definition
block: return bool from get_disk_ro and bdev_read_only
block: remove a duplicate definition for bdev_read_only
block: return bool from blk_rq_aligned
block: return unsigned int from blk_lim_dma_alignment_and_pad
block: return unsigned int from queue_dma_alignment
block: return unsigned int from bdev_io_opt
block: req->bio is always set in the merge code
block: don't bother checking the data direction for merges
block: blk-mq: fix uninit-value in blk_rq_prep_clone and refactor
Revert "block, bfq: merge bfq_release_process_ref() into bfq_put_cooperator()"
md/raid10: Atomic write support
md/raid1: Atomic write support
...
Pull more io_uring updates from Jens Axboe:
- Remove a leftover struct from when the cqwait registered waiting was
transitioned to regions.
- Fix for an issue introduced in this merge window, where nop->fd might
be used uninitialized. Ensure it's always set.
- Add capping of the task_work run in local task_work mode, to prevent
bursty and long chains from adding too much latency.
- Work around xa_store() leaving ->head non-NULL if it encounters an
allocation error during storing. Just a debug trigger, and can go
away once xa_store() behaves in a more expected way for this
condition. Not a major thing as it basically requires fault injection
to trigger it.
- Fix a few mapping corner cases
- Fix KCSAN complaint on reading the table size post unlock. Again not
a "real" issue, but it's easy to silence by just keeping the reading
inside the lock that protects it.
* tag 'io_uring-6.13-20242901' of git://git.kernel.dk/linux:
io_uring/tctx: work around xa_store() allocation error issue
io_uring: fix corner case forgetting to vunmap
io_uring: fix task_work cap overshooting
io_uring: check for overflows in io_pin_pages
io_uring/nop: ensure nop->fd is always initialized
io_uring: limit local tw done
io_uring: add io_local_work_pending()
io_uring/region: return negative -E2BIG in io_create_region()
io_uring: protect register tracing
io_uring: remove io_uring_cqwait_reg_arg
Pull dma-mapping fix from Christoph Hellwig:
- fix physical address calculation for struct dma_debug_entry (Fedor
Pchelkin)
* tag 'dma-mapping-6.13-2024-11-30' of git://git.infradead.org/users/hch/dma-mapping:
dma-debug: fix physical address calculation for struct dma_debug_entry
Pull more kvm updates from Paolo Bonzini:
- ARM fixes
- RISC-V Svade and Svadu (accessed and dirty bit) extension support for
host and guest
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: riscv: selftests: Add Svade and Svadu Extension to get-reg-list test
RISC-V: KVM: Add Svade and Svadu Extensions Support for Guest/VM
dt-bindings: riscv: Add Svade and Svadu Entries
RISC-V: Add Svade and Svadu Extensions Support
KVM: arm64: Use MDCR_EL2.HPME to evaluate overflow of hyp counters
KVM: arm64: Ignore PMCNTENSET_EL0 while checking for overflow status
KVM: arm64: Mark set_sysreg_masks() as inline to avoid build failure
KVM: arm64: vgic-its: Add stronger type-checking to the ITS entry sizes
KVM: arm64: vgic: Kill VGIC_MAX_PRIVATE definition
KVM: arm64: vgic: Make vgic_get_irq() more robust
KVM: arm64: vgic-v3: Sanitise guest writes to GICR_INVLPIR
Pull sh updates from John Paul Adrian Glaubitz:
"Two small fixes.
The first one by Huacai Chen addresses a runtime warning when
CONFIG_CPUMASK_OFFSTACK and CONFIG_DEBUG_PER_CPU_MAPS are selected
which occurs because the cpuinfo code on sh incorrectly uses NR_CPUS
when iterating CPUs instead of the runtime limit nr_cpu_ids.
A second fix by Dan Carpenter fixes a use-after-free bug in
register_intc_controller() which occurred as a result of improper
error handling in the interrupt controller driver code when
registering an interrupt controller during plat_irq_setup() on sh"
* tag 'sh-for-v6.13-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/glaubitz/sh-linux:
sh: intc: Fix use-after-free bug in register_intc_controller()
sh: cpuinfo: Fix a warning for CONFIG_CPUMASK_OFFSTACK
Pull arm64 fixes from Catalin Marinas:
- Deselect ARCH_CORRECT_STACKTRACE_ON_KRETPROBE so that tests depending
on it don't run (and fail) on arm64
- Fix lockdep assert in the Arm SMMUv3 PMU driver
- Fix the port and device ID bits setting in the Arm CMN perf driver
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
perf/arm-cmn: Ensure port and device id bits are set properly
perf/arm-smmuv3: Fix lockdep assert in ->event_init()
arm64: disable ARCH_CORRECT_STACKTRACE_ON_KRETPROBE tests
since 2024.07.26:
assorted minor bug fixes
assorted platform specific tweaks
initial RAPL PSYS (SysWatt) support
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce the counter as a part of global, platform counters structure.
We open the counter for only one cpu, but otherwise treat it as an
ordinary RAPL counter, allowing for grouped perf read.
The counter is disabled by default, because it's interpretation may
require additional, platform specific information, making it unsuitable
for general use.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add '+' to optstring when early scanning for --no-msr and --no-perf.
It causes option processing to stop as soon as a nonoption argument is
encountered, effectively skipping child's arguments.
Fixes: 3e4048466c ("tools/power turbostat: Add --no-msr option")
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Force the --no-perf early to prevent using it as a source. User asks for
raw values, but perf returns them relative to the opening of the file
descriptor.
Signed-off-by: Patryk Wlazlyn <patryk.wlazlyn@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
On some machines, the graphics device is enumerated as
/sys/class/drm/card1 instead of /sys/class/drm/card0. The current
implementation does not handle this scenario, resulting in the loss of
graphics C6 residency and frequency information.
Add support for /sys/class/drm/card1, ensuring that turbostat can
retrieve and display the graphics columns for these platforms.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Snapshots of the graphics sysfs knobs are taken based on file
descriptors. To optimize this process, open the files and cache the file
descriptors during the graphics probe phase. As a result, the previously
cached pathnames become redundant and are removed.
This change aims to streamline the code without altering its functionality.
No functional change intended.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently, there is an inconsistency in how graphics sysfs knobs are
accessed: graphics residency sysfs knobs are opened and closed for each
read, while graphics frequency sysfs knobs are opened once and remain
open until turbostat exits. This inconsistency is confusing and adds
unnecessary code complexity.
Consolidate the access method by opening the sysfs files once and
reusing the file pointers for subsequent accesses. This approach
simplifies the code and ensures a consistent method for accessing
graphics sysfs knobs.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The graphics sysfs knobs are read-only, making the use of fflush()
before reading them redundant.
Remove the unnecessary fflush() call.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
In various generations, platforms often share a majority of features,
diverging only in a few specific aspects. The current approach of using
hardcoded values in 'platform_features' structure fails to effectively
represent these divergences.
To improve the description of platform divergence:
1. Each newly introduced 'platform_features' structure must have a base,
typically derived from the previous generation.
2. Platform feature values should be inherited from the base structure
rather than being hardcoded.
This approach ensures a more accurate and maintainable representation of
platform-specific features across different generations.
Converts `adl_features` and `lnl_features` to follow this new scheme.
No functional change.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add initial support for GraniteRapids-D. It shares the same features
with SapphireRapids.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Lunarlake supports CC1/CC6/CC7/PC2/PC6/PC10.
Remove PC3 support on Lunarlake.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
