The call to gpiod_set_value_cansleep() in cs42l42_sdw_update_status()
needs the header file gpio/consumer.h to be included.
This was introduced by commit 2d066c6a78 ("ASoC: cs42l42: Avoid stale
SoundWire ATTACH after hard reset")
and caused error:
sound/soc/codecs/cs42l42-sdw.c:374:4: error: implicit declaration of
function ‘gpiod_set_value_cansleep’;
did you mean gpio_set_value_cansleep’?
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2d066c6a78 ("ASoC: cs42l42: Avoid stale SoundWire ATTACH after hard reset")
Link: https://lore.kernel.org/r/20231011134853.20059-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASP1 DOUT line must be defaulted to be high-impedance when
it is not actually transmitting data for an active channel.
In non-SoundWire modes ASP1 will usually be shared by multiple
amps so each amp must only drive the line during the slot for
an enabled TX channel.
In SoundWire mode a custom firmware can use ASP1 as a secondary
chip-to-chip audio link or as GPIO. It should be defaulted to
high-impedance since by default the purpose of this pin is not
known.
Backport note:
On kernel versions before 6.6 the cs35l56->base.regmap argument
to regmap_set_bits() must be changed to cs35l56->regmap.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://lore.kernel.org/r/20231009153412.30380-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>:
Some codec drivers compare widget names with strcmp, ignoring the component
name prefix. If prefix is used, the comparisons start failing.
Add a helper to fix the issue.
Merge series from Johan Hovold <johan+linaro@kernel.org>:
The wcd938x codec driver happily ignores error handling, something which
has bitten us in the past when we hit a probe deferral:
https://lore.kernel.org/lkml/20230705123018.30903-1-johan+linaro@kernel.org/
Fix up the remaining probe and component bind paths that left resources
allocated and registered after errors to avoid similar future issues.
Commit 4e08713336 ("ASoC: hdmi-codec: fix channel info for
compressed formats") accidentally changed hcp->chmap_idx from
ca_id, the CEA channel allocation ID, to idx, the index to
the table of channel mappings ordered by preference.
This resulted in wrong channel maps being reported to userspace,
eg for 5.1 "FL,FR,LFE,FC" was reported instead of the expected
"FL,FR,LFE,FC,RL,RR":
~ # speaker-test -c 6 -t sine
...
0 - Front Left
3 - Front Center
1 - Front Right
2 - LFE
4 - Unknown
5 - Unknown
~ # amixer cget iface=PCM,name='Playback Channel Map' | grep ': values'
: values=3,4,8,7,0,0,0,0
Switch this back to ca_id in case of PCM audio so the correct channel
map is reported again and set it to HDMI_CODEC_CHMAP_IDX_UNKNOWN in
case of non-PCM audio so the PCM channel map control returns "Unknown"
channels (value 0).
Fixes: 4e08713336 ("ASoC: hdmi-codec: fix channel info for compressed formats")
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20230929195027.97136-1-hias@horus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On init we have sequence:
for_each_card_prelinks(card, i, dai_link) {
ret = snd_soc_add_pcm_runtime(card, dai_link);
ret = init_some_other_things(...);
if (ret)
goto probe_end:
for_each_card_rtds(card, rtd) {
ret = soc_init_pcm_runtime(card, rtd);
probe_end:
while on exit:
for_each_card_rtds(card, rtd)
snd_soc_link_exit(rtd);
If init_some_other_things() step fails due to error we end up with
not fully setup rtds and try to call snd_soc_link_exit on them, which
depending on contents on .link_exit handler, can end up dereferencing
NULL pointer.
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230929103243.705433-2-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting ACP ACLK as clock source when ACP enters D0 state causing
firmware load failure as mentioned in below scenario.
- Load snd_sof_amd_rembrandt
- Play or Record audio
- Stop audio
- Unload snd_sof_amd_rembrandt
- Reload snd_sof_amd_rembrandt
If acp_clkmux_sel register field is set, then clock source will be
set to ACP ACLK when ACP enters D0 state.
During stream stop, if there is no active stream is running then
acp firmware will set the ACP ACLK value to zero.
When driver is reloaded and clock source is selected as ACP ACLK,
as ACP ACLK is programmed to zero, firmware loading will fail.
For RMB platform, remove the clock mux selection field so that
ACP will use internal clock source when ACP enters D0 state.
Fixes: 41cb85bc4b ("ASoC: SOF: amd: Add support for Rembrandt plaform.")
Reported-by: coolstar <coolstarorganization@gmail.com>
Closes: https://github.com/thesofproject/sof/issues/8137
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Link: https://lore.kernel.org/r/20230927071412.2416250-1-Vijendar.Mukunda@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the pll_id and pll_id can be zero (WM8960_SYSCLK_AUTO)
with the commit 2bbc2df46e ("ASoC: wm8960: Make automatic the
default clocking mode")
Then the machine driver will skip to call set_sysclk() and set_pll()
for codec, when the sysclk rate is different with what wm8960 read
at probe, the output sound frequency is wrong.
So change the fll_id and pll_id initial value, still keep machine
driver's behavior same as before.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1695202992-24864-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
On i.MX8MP, the BCE and TERE bit are binding with mclk
enablement, if BCE and TERE are cleared the MCLK also be
disabled on output pin, that cause the external codec (wm8960)
in wrong state.
Codec (wm8960) is using the mclk to generate PLL clock,
if mclk is disabled before disabling PLL, the codec (wm8960)
won't generate bclk and frameclk when sysclk switch to
MCLK source in next test case.
The test case:
$aplay -r44100 test1.wav (PLL source)
$aplay -r48000 test2.wav (MCLK source)
aplay: pcm_write:2127: write error: Input/output error
Fixes: 269f399dc1 ("ASoC: fsl_sai: Disable bit clock with transmitter")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1695116533-23287-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
asoc_simple_probe() is used for both "DT probe" (A) and "platform probe"
(B). It uses "goto err" when error case, but it is not needed for
"platform probe" case (B). Thus it is using "return" directly there.
static int asoc_simple_probe(...)
{
^ if (...) {
| ...
(A) if (ret < 0)
| goto err;
v } else {
^ ...
| if (ret < 0)
(B) return -Exxx;
v }
...
^ if (ret < 0)
(C) goto err;
v ...
err:
(D) simple_util_clean_reference(card);
return ret;
}
Both case are using (C) part, and it calls (D) when err case.
But (D) will do nothing for (B) case.
Because of these behavior, current code itself is not wrong,
but is confusable, and more, static analyzing tool will warning on
(B) part (should use goto err).
To avoid static analyzing tool warning, this patch uses "goto err"
on (B) part.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87o7hy7mlh.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
i.MX rpmsg sound cards work on codec slave mode. MCLK will be disabled
by CPU DAI driver in hw_free(). Some codec requires MCLK present at
power up/down sequence. So need to set ignore_pmdown_time to power down
codec immediately before MCLK is turned off.
Take WM8962 as an example, if MCLK is disabled before DAPM power down
playback stream, FIFO error will arise in WM8962 which will have bad
impact on playback next.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Shengjiu Wang <shengjiu.wang@gmail.com>
Link: https://lore.kernel.org/r/20230913102656.2966757-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Stefan Binding <sbinding@opensource.cirrus.com>:
These patches fix 3 problems with hard reset:
1. Ensure a minimum reset pulse width
2. Deal with ACPI overriding the requested default GPIO state
3. Avoid a race condition when hard-resetting a SoundWire peripheral
that is already enumerated
Change the logging of each algorithm from info level to debug level.
On the original devices supported by this code there were typically only
one or two algorithms in a firmware and one or two DSPs so this logging
only used a small number of log lines.
However, for the latest devices there could be 30-40 algorithms in a
firmware and 8 DSPs being loaded in parallel, so using 300+ lines of log
for information that isn't particularly important to have logged.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913160523.3701189-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
In SoundWire mode leave hard RESET asserted when exiting probe,
and wait for an UNATTACHED notification before deasserting RESET.
If the boot state of the reset GPIO was deasserted it is possible
that the SoundWire core had already enumerated the CS42L42 before
cs42l42_sdw_probe() is called. When cs42l42_common_probe() hard
resets the CS42L42 it triggers a race condition:
1) After cs42l42_sdw_probe() returns the thread that called it
will call cs42l42_sdw_update_status() to report the last
status recorded by the SoundWire core.
2) The SoundWire bus master will see a PING with the CS42L42
now reporting as unenumerated and will trigger the core
SoundWire code to start enumerating CS42L42.
These two threads are racing against each other. If (1)
happens before (2) a stale ATTACHED notification will be
reported to the cs42l42 driver when in fact the status of
cs42l42 is now unattached.
To avoid this race condition:
- Leave RESET asserted on exit from cs42l42_sdw_probe().
This ensures that an UNATTACHED notification must be
sent to the cs42l42 driver. If cs42l42 was already
enumerated it will be seen to drop off the bus, causing
an UNATTACH notification. If it was never enumerated the
status is already UNATTACHED and this will be reported
by thread (1).
- When the UNATTACH notification is received, release RESET.
This will cause CS42L42 to be enumerated and eventually
report an ATTACHED notification.
- The ATTACHED notification is now valid.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230913150012.604775-4-sbinding@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
