Add a driver for Arm's Mali-C55 Image Signal Processor. The driver is
V4L2 and Media Controller compliant and creates subdevices to manage
the ISP itself, its internal test pattern generator as well as the
crop, scaler and output format functionality for each of its two
output devices.
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Nayden Kanchev <nayden.kanchev@arm.com>
Co-developed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
[hverkuil: remove deprecated vb2_ops_wait_prepare/finish callbacks]
Introduce v4l2-isp.h in the Linux kernel uAPI.
The header includes types for generic ISP configuration parameters
and will be extended in the future with support for generic ISP statistics
formats.
Generic ISP parameters support is provided by introducing two new
types that represent an extensible and versioned buffer of ISP
configuration parameters.
The v4l2_params_buffer represents the container for the ISP
configuration data block. The generic type is defined with a 0-sized
data member that the ISP driver implementations shall properly size
according to their capabilities. The v4l2_params_block_header structure
represents the header to be prepend to each ISP configuration block.
Signed-off-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Michael Riesch <michael.riesch@collabora.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add a v4l2 sub-device driver for the Sony IMX111 image sensor. This is a
camera sensor using the i2c bus for control and the csi-2 bus for data.
The following features are supported:
- manual exposure, digital and analog gain control support
- pixel rate/link freq control support
- supported resolution up to 3280x2464 for single shot capture
- supported resolution up to 1920x1080 @ 30fps for video
- supported bayer order output SGBRG10 and SGBRG8
Camera module seems to be partially compatible with Nokia SMIA but it
lacks a few registers required for clock calculations and has different
vendor-specific per-mode configurations which makes it incompatible with
existing CCS driver.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
[Sakari Ailus: Fix set_fmt() callback a bit and idle after autosuspend.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Commit c423487bf6 ("dt-bindings: media: convert nxp,tda1997x.txt to yaml
format") renames nxp,tda1997x.txt to nxp,tda19971.yaml as part of this
dt-binding conversion, but misses to adjust the file entry in TDA1997x
MEDIA DRIVER.
Adjust the file entry after the conversion.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Introduce IMX219_EXPOSURE_OFFSET (4) and use it instead of the literal
'4' when computing the maximum coarse exposure. The IMX219 datasheet
specifies the maximum storage time as frame_length_lines - 4.
(Ref: Datasheet section 5-7-1)
Also fix one indentation issue for consistency.
Signed-off-by: Tarang Raval <tarang.raval@siliconsignals.io>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Propagate return values from __v4l2_ctrl_modify_range() and
__v4l2_ctrl_s_ctrl() in imx219_set_ctrl() and imx219_set_pad_format().
This ensures proper error handling instead of ignoring possible
failures. Also return the result of imx219_set_pad_format() from
imx219_init_state().
Signed-off-by: Tarang Raval <tarang.raval@siliconsignals.io>
Reviewed-by: Isaac Scott <isaac.scott@ideasonboard.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add support for monochrome media bus formats, for use with monochrome/IR
camera sensors.
This has been tested on a Dell XPS 13 9320 with OV1A1B IR sensor.
Signed-off-by: Hans de Goede <hansg@kernel.org>
Reviewed-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Smatch is confused by the control initialization logic. It assumes that
there can be a case where imx214->link_freq can be NULL and ctrls_init
returns 0.
Re-arrange the function to make smatch happy.
This patch fixes this smatch error:
drivers/media/i2c/imx214.c:1109 imx214_ctrls_init() error: we previously assumed 'imx214->link_freq' could be null (see line 1017)
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Call on v4l2_get_active_data_lanes() to check if the driver reports that
the number of lanes actively used by the MIPI CSI transmitter differs to
the maximum defined in device tree.
If the number of active data lanes reported by the driver is invalid,
catch and return the error. If the operation is not supported, fall back
to the number of allowed data lanes.
Signed-off-by: Isaac Scott <isaac.scott@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Add the num_data_lanes field to the mipi_csis_device struct, and set it
equal to csis->bus.num_data_lanes. This is in preparation to support
cases when the data lanes actively used differs from the maximum
supported data lanes.
No functional changes intended by this commit.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Isaac Scott <isaac.scott@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Sometimes, users will not use all of the MIPI CSI 2 lanes available when
connecting to the MIPI CSI receiver of their device. Add a helper
function that checks the mbus_config for the device driver to allow
users to define the number of active data lanes through the
get_mbus_config op.
If the driver does not implement this op, fall back to using the maximum
number of lanes available.
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Isaac Scott <isaac.scott@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Introduce 2x2 binning mode (1312x972@60fps). Since there are multiple
modes now, use v4l2_find_nearest_size() to select the appropriate mode
in .set_fmt().
For 2x2 binning the minimum shutter value supported is 17 instead of 9.
This effects the maximum allowed exposure time, and if not enforced then
the sensor produces very dark frames when the minimum shutter limit is
violated.
Lastly, update the crop size reported to the userspace. When trying 2x2
binning with the datasheet suggested pixel array size (i.e. 2592 / 2 =>
1296), on some platforms (Raspberry Pi 5) artefacts are introduced on
the right edge of the output image. Instead, using a higher width of
1312 works fine on all platforms.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
While switching modes, updating to a different value of HBLANK isn't
sufficient, as this is a read-only control with a single allowed value,
and thus hblank_min == hblank_max == hblank of the default mode.
So to correctly update the user-facing value of the HBLANK parameter,
which is necessary for correct framerate calculation, update the whole
range when switching modes.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Support vertical flip by setting REG_VREVERSE.
Additional registers also needs to be set per mode, according
to the readout direction (normal/inverted) as mentioned in the
data sheet.
Since the register IMX335_REG_AREA3_ST_ADR_1 is based on the
flip (and is set via vflip related registers), it has been
moved out of the 2592x1944 mode regs.
Signed-off-by: Umang Jain <umang.jain@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Jai Luthra <jai.luthra@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Linux 6.18-rc5
* tag 'v6.18-rc5': (1016 commits)
Linux 6.18-rc5
kbuild: Let kernel-doc.py use PYTHON3 override
rtc: rx8025: fix incorrect register reference
Revert "drm/nouveau: set DMA mask before creating the flush page"
io_uring: fix regbuf vector size truncation
compiler_types: Move unused static inline functions warning to W=2
smb: client: validate change notify buffer before copy
tracing/tools: Fix incorrcet short option in usage text for --threads
drm/xe: Enforce correct user fence signaling order using
x86/microcode/AMD: Add more known models to entry sign checking
drm/xe: Do clean shutdown also when using flr
drm/xe: Move declarations under conditional branch
drm/xe/guc: Synchronize Dead CT worker with unbind
tracing: Fix memory leaks in create_field_var()
ring-buffer: Do not warn in ring_buffer_map_get_reader() when reader catches up
tracing: tprobe-events: Fix to put tracepoint_user when disable the tprobe
tracing: tprobe-events: Fix to register tracepoint correctly
gpio: tb10x: Drop unused tb10x_set_bits() function
drm/amd/display: Enable mst when it's detected but yet to be initialized
drm/amdgpu: Fix wait after reset sequence in S3
...
For ternary operators in the form of "a ? false : true", if 'a' itself
returns a boolean result, the ternary operator can be omitted. Remove
redundant ternary operators to clean up the code.
Signed-off-by: Liao Yuanhong <liaoyuanhong@vivo.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The driver calls reset_control_get_optional_exclusive() but never calls
reset_control_put() in error paths or in the remove function. This causes
a resource leak when probe fails after successfully acquiring the reset
control, or when the driver is unloaded.
Switch to devm_reset_control_get_optional_exclusive() to automatically
manage the reset control resource.
Fixes: a4b80242d0 ("media: st-rc: explicitly request exclusive reset control")
Cc: stable@vger.kernel.org
Signed-off-by: Haotian Zhang <vulab@iscas.ac.cn>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The driver has never supported anything but OF probing so drop the
unused platform module alias.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Pull i2c fix from Wolfram Sang:
"Two reverts merged into one commit to handle a regression caused by a
wrong cleanup because the underlying implications were unclear"
* tag 'i2c-for-6.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: muxes: pca954x: Fix broken reset-gpio usage
Pull Kbuild fixes from Nathan Chancellor:
- Strip trailing padding bytes from modules.builtin.modinfo to fix
error during modules_install with certain versions of kmod
- Drop unused static inline function warning in .c files with clang
from W=1 to W=2
- Ensure kernel-doc.py invocations use the PYTHON3 make variable to
ensure user's choice of Python interpreter is always respected
* tag 'kbuild-fixes-6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Let kernel-doc.py use PYTHON3 override
compiler_types: Move unused static inline functions warning to W=2
kbuild: Strip trailing padding bytes from modules.builtin.modinfo
It is possible to force a specific version of python to be used when
building the kernel by passing PYTHON3= on the make command line.
However kernel-doc.py is currently called with python3 hard-coded and
thus ignores this setting.
Use $(PYTHON3) to run $(KERNELDOC) so that the desired version of
python is used.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Nicolas Schier <nsc@kernel.org>
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://patch.msgid.link/20251107192933.2bfe9e57@endymion
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Pull drm fix from Dave Airlie:
"Brown paper bag, the dma mask fix which I applied and actually looked
through for bad things, actually broke newer GPUs, there might be some
latent part in the boot path that is assuming 32-bit still, but we
will figure that out elsewhere.
nouveau:
- revert DMA mask change"
* tag 'drm-fixes-2025-11-09' of https://gitlab.freedesktop.org/drm/kernel:
Revert "drm/nouveau: set DMA mask before creating the flush page"
Pull x86 fixes from Ingo Molnar:
- Fix AMD PCI root device caching regression that triggers
on certain firmware variants
- Fix the zen5_rdseed_microcode[] array to be NULL-terminated
- Add more AMD models to microcode signature checking
* tag 'x86-urgent-2025-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode/AMD: Add more known models to entry sign checking
x86/CPU/AMD: Add missing terminator for zen5_rdseed_microcode
x86/amd_node: Fix AMD root device caching
