Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
Introduce new wrapper to present spcm related debug and error prints in
a unified way and provide additional details to help to understand the
reasons and configuration used when the log was captured.
Change the way we print information about the ipc4 copier module to
use type specific prints, again to provide better information for
debugging.
Merge series from Mohammad Rafi Shaik <quic_mohs@quicinc.com>:
Add static channel map support between soundwire master and slave.
Currently, the channel value for each soundwire port is hardcoded in the
wcd937x-sdw driver and the same channel value is configured in the
soundwire master.
The Qualcomm board like the QCM6490-IDP require static channel map
settings for the soundwire master and slave ports.
If another boards which are using enable wcd937x, the channel mapping
index values between master and slave may be different depending on the
board hw design and requirements. If the above properties are not used
in a SoC specific device tree, the channel mapping index values are set
to default.
With the introduction of the following channel mapping properties, it is
now possible to configure the master channel mapping directly from the
device tree.
Added qcom_swrm_set_channel_map api to set the master channel values
which allows more flexible to configure channel values in runtime for
specific active soundwire ports.
Add get and set channel maps support from codec to cpu dais in common
Qualcomm sdw driver.
Merge series from Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>:
cpcap audio codec found on cpcap PMIC supports headset detection
and PTT button through its 3.5 mm jack. This series implements
support for those capabilities.
Merge series from Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>:
Each ASoC framwark is using own snd_xxx_ret() function, but we can share
these. This patch-set adds new snd_soc_ret() and use it.
checkpatch indicates that ENOTSUPP is not a SUSV4 error code, prefer to
use EOPNOTSUPP. So this patch-set adds it, but not remove existing ENOTSUPP.
Link: https://lore.kernel.org/r/8734gvsg5i.wl-kuninori.morimoto.gx@renesas.com
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
The avs-driver is the go-to driver for Intel Automotive. MalibouLake
(MBL) and RedondoLake (RDL) are representatives of the project. These
inherit majority of the featureset from RaptorLake-M (RPL-M) and
AlderLake-N (ADL-N) respectively. The onboard codec for these is TI's
pcm3168a.
In summary, the patchset:
- modifies existing pcm3168a.c to be x86/ACPI friendly
- updates the DSP firmware booting sequence for cAVS 2.5 platforms to
improve its behaviour on some specific revisions/steppings of the
hardware
- adds new machine board driver, avs_pcm3168a
- adds selector entry for RPL-M devices in intel-dspcfg
While there 'ALSA: hda:' patch within the list, I'd prefer the patchset
to go through Mark's tree to avoid conflicts with follow ups to this
one.
Longer version:
Currently the pcm3168a is supported on ARM/DT (ti/j721e-evm.c being the
only user). To make it x86/ACPI friendly, add relevant ACPI-match table
and relax driver's probing conditions.
The default format is 2ch, 24-bits, 48000kHz. As per specification,
24-bits are supported by the chip and it works in production in contrary
to what the existing code suggests. A fix is provided to align the code
with the spec.
Now, a single DSP firmware binary covers a wide range of platforms - a
single one covers AlderLake, RaptorLake and all their derevatires except
for AlderLake-N based due to MEU differences. While most of the hardware
capabilities are read by the firmware during runtime, some information is
not accessible from the DSP level. Provide the HDAudio controller
revision/stepping information to the firmware to address that.
With that done, expand number of modules supported with WovHostModule
(WHM). WHM is a processing module which is tailored for ultra-low-power
scenarios. From software perspective, as most of its config is similar
to the Copier module, code reuse is advised. To make the reuse possible,
existing gateway configuration code is refactor - not only to add
support for WHM but also make it easier to understand. Multiple smaller
functions instead of all-in-one one.
A split SOF release consists of a base firmware and two libraries:
<fw_filename>-openmodules.ri for processing (audio) modules
<fw_filename>-debug.ri for debug and developer modules
To handle this new release model add infrastructure to try to load the two
library after boot optionally.
This approach will allow flexibility on handling platforms in sof-bin with
single or split configuration:
single release: base firmware only
split release: base firmware + openmodules + debug
The files for the split firmware are located at the firmware directory.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20250206085237.19214-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of initializing the be_rate within the loop by checking i == 0 at
each iteration, move the be_rate reference initialization from the loop.
For BE single rate check we will have single comparison done at each
iteration compared to two in case the num_input_formats were higher than 1.
We still need to run the loop from index 0 to check for FE-BE rate match.
The patch also fixes bogus reports from gcc static analyzer thinking that
be_rate is used uninitialized later in the function (which was not true).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Link: https://patch.msgid.link/20250206094914.21135-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Added qcom_swrm_set_channel_map api to set the master channel mask for
TX and RX paths based on the provided slots.
Added a new field ch_mask to the qcom_swrm_port_config structure.
This field is used to store the master channel mask, which allows more
flexible to configure channel mask in runtime for specific active
soundwire ports.
Modified the qcom_swrm_port_enable function to configure master
channel mask. If the ch_mask is set to SWR_INVALID_PARAM or is zero,
the function will use the default channel mask.
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Acked-by: Vinod Koul <vkoul@kernel.org>
Link: https://patch.msgid.link/20250206112225.3270400-4-quic_mohs@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add static channel mapping between master and slave ports in wcd937x-sdw
driver.
Currently, the channel mask for each soundwire port is hardcoded in the
wcd937x-sdw driver, and the same channel mask value is configured in the
soundwire master.
The Qualcomm boards like the QCM6490-IDP require different channel mask
settings for the soundwire master and slave ports.
Implemented logic to read TX/RX channel mappings from device tree
properties (qcom,tx-channel-mapping and qcom,rx-channel-mapping).
Modified the wcd937x_connect_port to handle master channel masks during
port enable/disable operations.
Added wcd937x_get_channel_map api to retrieve the current master
channel map for TX and RX paths.
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Link: https://patch.msgid.link/20250206112225.3270400-3-quic_mohs@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add static channel mapping between master and slave rx/tx ports for
Qualcomm wcd937x soundwire codec.
Currently, the channel map index value for each soundwire port is
hardcoded in the wcd937x-sdw driver, and the same channel map index
value is configured in the soundwire master.
The Qualcomm board like the QCM6490-IDP require static channel map
settings for the soundwire master and slave ports.
If another boards which are using enable wcd937x, the channel mapping
index values between master and slave may be different depending on the
board hw design and requirements. If the above properties are not used
in a SoC specific device tree, the channel mapping index values are set
to default.
With the introduction of the following channel mapping properties, it is
now possible to configure the master channel mapping directly from the
device tree.
The qcom,tx-channel-mapping property specifies the static channel mapping
between the slave and master tx ports in the order of slave port channels
which is adc1, adc2, adc3, adc4, dmic0, dmic1, mbhc, dmic2, dmic3, dmci4,
dmic5, dmic6, dmic7.
The qcom,rx-channel-mapping property specifies the static channel mapping
between the slave and master rx ports in the order of slave port channels
which is hph_l, hph_r, clsh, comp_l, comp_r, lo, dsd_r, dsd_l.
Signed-off-by: Mohammad Rafi Shaik <quic_mohs@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20250206112225.3270400-2-quic_mohs@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
