This add a DTS for the Digilent Zybo Z7 board.
This board is the successor board of Zybo, these are almost the same except
for ps-clk-frequency specifications.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu@cybertrust.co.jp>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, ethernet, i2c, qspi, spi and uart.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, 2x i2c, nor flash, spi and uart.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains can, i2c, nand uart, spi and usb.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
zc770 is based board which is extended by FMC/DC cards for SoC
validation. FMCs/DCs are supposed to cover all SoC configurations.
FMC/DC contains ethernet port, can, i2c, sd, qspi, spi, uart and usb.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The board contains 7z010 with 512MB memory, ethernet, qspi, uart, usbs
and sd. But board is not supporting booting from sd card.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch is fixing issue reported by dtc:
arch/arm/boot/dts/zynq-microzed.dtb: Warning (unit_address_vs_reg): Node
/memory has a reg or ranges property, but no unit name
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx zc1751 boards is used for silicon validation. Board can be
extended with 5 FMCs/DCs cards to connect various IPs. Describe all
these combinations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
These 3 boards requires minimal support to get Linux up and running.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu111 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu106 is a customer board. It is reusing some parts from zcu102.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Xilinx zcu104 is another customer board. It is sort of zcu102 clone
with some differences.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch is adding revA, revB and rev1.0. There are also other
revisions between which should be backward compatible with previous
versions. Unfortunately all revs are still in use.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This board has 2GB of memory, i2c, sd, wifi sdio, spis, uarts, display
port and usbs.
Board is using fixed clocks because clock driver hasn't been merged yet.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Rob Herring <robh@kernel.org>
This patch adds the sata port phy OOB timing values in the sata
device-tree node.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Pull "Samsung DTS ARM64 changes for v4.17" from Krzysztof Kozłowski:
1. Add support for HDMI audio on Exynos 5433 TM2/TM2E boards.
2. Add support for USB-MHL connector on Exynos 5433 TM2/TM2E boards.
* tag 'samsung-dt64-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: add OF graph between MHL and USB connector
arm64: dts: exynos: add micro-USB connector node to TM2 platforms
ARM: dts: exynos: Add support for HDMI audio on Exynos 5433 TM2 board
ARM: dts: exynos: Update I2S0 device node in exynos5433
ARM: dts: exynos: Add I2S1 device node to exynos5433
Pull "Samsung DTS ARM changes for v4.17" from Krzysztof Kozłowski:
1. Add WiFi to Artik 5 board.
2. Remove unused samsung_k3pe0e000b memory DTSI.
3. Add few remaining SPDX license identifiers.
4. Refactor Exynos4 by using labels for overriding/extending nodes and
moving respective nodes under the 'soc' node.
5. Add three new Exynos4412-based boards: GT-I9300 (Samsung Galaxy S3),
GT-I9305 (Samsung Galaxy S3 LTE) and GT-N7100/N7105 (Samsung Note 2).
They are based heavily on existing Trats2 board.
6. Fix PMIC interrupts on Trats board.
7. Fix IOMMU for GScaler devices on Exynos5250.
8. Minor fixes in unit addresses pointed by DTC.
9. Minor cleanups from unused properties and duplicated code.
* tag 'samsung-dt-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (29 commits)
ARM: dts: exynos: Fix IOMMU support for GScaler devices on Exynos5250
ARM: dts: exynos: Remove unused bypass-smu property from Xyref5260
ARM: dts: exynos: Add missing interrupts property to PMIC on Trats board
ARM: dts: exynos: Fix unit addresses of PDMA nodes in Exynos5410
ARM: dts: exynos: Fix address of PPMU ACP on Exynos4210
ARM: dts: exynos: Cleanup power domain nodes in exynos3250.dtsi
ARM: dts: exynos: Add touchscreen node to Exynos4412 N710x
ARM: dts: exynos: Add Samsung's Exynos4412-based Midas boards
ARM: dts: exynos: Split Trats2 DTS in preparation for Midas boards
ARM: dts: exynos: Remove "cooling-{min|max}-level" for CPU nodes
dt-bindings: samsung: Document bindings for Midas family boards
ARM: dts: exynos: Add soc node to exynos4412
ARM: dts: exynos: Add soc node to exynos4210
ARM: dts: exynos: Add soc node to exynos4
ARM: dts: exynos: Add soc node to exynos5440
ARM: dts: exynos: Use pmu label in exynos4412
ARM: dts: exynos: Remove duplicated inclusion of syscon restart nodes on Exynos5410
ARM: dts: exynos: Use label instead of full path in exynos4412-itop-elite
ARM: dts: exynos: Use labels instead of full paths in exynos4412-trats2
ARM: dts: exynos: Use label instead of full path in exynos4412-odroid-common
...
As of commit 7f60830ab1 ("serial: sirf: Use generic
uart-has-rtscts DT property property"), the SiRF UART driver recognizes
the generic "uart-has-rtscts" DT property, deprecating the
vendor-specific "sirf,uart-has-rtscts" DT property. Hence replace the
latter by the former in all DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "STM32 DT updates for v4.17, round 1" from Alexandre Torgue:
Highlights:
-----------
-Add support of STM32MP157 MPU and stm32mp157c eval board
-Add SD supports on F4 and F7 boards
-Add leds support on stm32f469 and stm32f769 disco boards
-Add push button support on stm32f469 and stm32f769 disco boards
-Add EXTI, SPI, RTC, USB HS/FS support on STM32H743 MCU
-Add RTC and USB OTG HS on stm32f769-disco
-Use dedicated files for F7 pinctrl
* tag 'stm32-dt-for-v4.17-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (34 commits)
ARM: dts: stm32: Fix sdio2 rcc hard coded value
dt-bindings: mfd: Add STM32F7 SDMMC2 rcc entry
ARM: dts: stm32: Enable sdio1 for stm32f769-disco
ARM: dts: stm32: Enable sdio1 for stm32f746-eval
ARM: dts: stm32: Enable sdio1 for stm32f746-disco
ARM: dts: stm32: Add sdio pins definition for stm32f7
ARM: dts: stm32: add SPI support on STM32H743 SoC
ARM: dts: stm32: enable RTC on stm32h743i-eval
ARM: dts: stm32: add RTC support on STM32H743
ARM: dts: stm32: enable USB OTG HS on stm32h743i-eval
ARM: dts: stm32: add USB OTG HS and FS support for STM32H743 SoC
ARM: dts: stm32: enable RTC on stm32f769-disco
ARM: dts: stm32: enable USB HS on stm32f769-disco
ARM: dts: stm32: select otg mode for usbotg_hs on stm32746g_eval
ARM: dts: stm32: add gadget fifo sizes to usbotg_hs on stm32f746
ARM: dts: stm32: Add push button to stm32f769 Discovery board
ARM: dts: stm32: Add push button to stm32f469 Discovery board
ARM: dts: stm32: Add leds support to stm32f769 Discovery board
ARM: dts: stm32: Add leds support to stm32f469 Discovery board
ARM: dts: stm32: Fix HSE clock frequency for stm32h743i-disco board
...
Pull "Device tree changes for dra7 sdhci for v4.17" from Tony Lindgren:
This series from Sekhar Nori and Kishon Vijay Abraham I adds
sdhci related nodes for dra7. To support higher transfer speeds,
the iodelay pinmux controller needs to be also configured.
Note that as these changes need SDHCI_OMAP to be enabled to avoid
breaking booting for various systems, these changes are based on
two defconfig changes to enable SDHCI_OMAP in the defconfig files.
* tag 'omap-for-v4.17/dt-sdhci-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx-idk: Select pull down for mmc1_clk line in default mode
ARM: dts: dra71-evm: Select pull down for mmc1_clk line in default mode
ARM: dts: dra71-evm: Correct evm_sd regulator max voltage
ARM: dts: dra76-evm: Add "vqmmc-supply" property for mmc2
ARM: dts: am57xx-idk: Add "vqmmc-supply" property for mmc2
ARM: dts: dra7-evm: Add "vqmmc-supply" property for mmc2
ARM: dts: dra7-evm: Remove mmc specific pinmux
ARM: dts: am57xx-beagle-x15: Add "vqmmc-supply" property for mmc2
ARM: dts: dra76-evm: Add pinctrl data for higher speed MMC/SD modes
ARM: dts: dra76-evm: Shift to using common IOdelay data
ARM: dts: dra76x: Create a common file with MMC/SD IOdelay data
ARM: omap2plus_defconfig: Enable CONFIG_MMC_SDHCI_OMAP
ARM: multi_v7_defconfig: Enable CONFIG_MMC_SDHCI_OMAP
Pull "ARM: Keystone DTS for 4.17" from Santosh Shilimkar:
- Andrew's various DTS warning fixes
- clock address separator fix
- EDAC support for EMIF
- serial dts node unit address format fix
* tag 'keystone_dts_for_4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone-k2g: Fix unit-address formatting for serial nodes
dt-bindings: memory: ti-emif: add edac support under emif
ARM: dts: keystone-k2e-clocks: Fix missing unit address separator
ARM: dts: keystone-k2g: Move usb-phy nodes out of soc0
ARM: dts: keystone-k2g: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2g: Move keystone_irq to under device-state-control
ARM: dts: keystone-k2hk: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2l: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone-k2e: Move keystone_dsp_gpio to under device-state-control
ARM: dts: keystone: Move reset-controller to under device-state-control
ARM: dts: keystone: Move keystone_irq to under device-state-control
Pull "Device tree changes for omap variants for v4.17" from Tony Lindgren:
This series of changes updates the device tree files for omaps:
- Nokia N9 support for magnetometer
- Update at24 to use atmel as manufacturer for am335x-boneblue
- Add support for am33xx based PDU001 board
- Update Droid 4 touchscreen for reset-gpios and add audio
codec and soundcard
- Remove unused dra7 cooling level nodes
- A series of changes to configure am335x and am437x for PM
- Add pinmuxing for i2c2 and 3 for LogicPD boards
- Add EMIF interrupt infor for am437x and am335x
- Add missing omap3 sound-dai-cells
* tag 'omap-for-v4.17/dt-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: omap4-droid4: add soundcard
ARM: dts: motorola-cpcap-mapphone: add audio-codec
ARM: dts: omap3: Add missing #sound-dai-cells
ARM: dts: am43xx: add emif interrupt info
ARM: dts: am33xx: add emif interrupt info
ARM: dts: Add pinmuxing for i2c2 and i2c3 for LogicPD SOM-LV
ARM: dts: Add pinmuxing for i2c2 and i2c3 for LogicPD torpedo
ARM: dts: am4372: Mark omap_l3_noc with ti,no-idle
ARM: dts: am4372: Mark emif with ti,no-idle
ARM: dts: am33xx: Mark emif with ti,no-idle
ARM: dts: am4372: Add soc node
ARM: dts: am33xx: Add pm-sram phandle to soc node
ARM: dts: am4372: Update emif node
ARM: dts: am33xx: Update emif node
ARM: dts: am4372: Reserve pm code and data regions in ocmcram sram node
ARM: dts: am33xx: Reserve pm code and data regions in ocmcram sram node
ARM: dts: omap: Remove "cooling-{min|max}-level" for CPU nodes
ARM: dts: omap4-droid4: update touchscreen
ARM: dts: am33xx: add PDU001 board
ARM: dts: use 'atmel' as at24 manufacturer in am335x-boneblue
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "ARMv8 Vexpress/Juno DT updates for v4.17" from Sudeep Holla:
1. Extends support for missing 3 GICv2m MSI frames
2. Fixes the incorrect GICv2m frame size(64kB instead of 4kB)
* tag 'juno-updates-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: fix size of GICv2m MSI frames
arm64: dts: juno: Describe the full GICv2m region
'linux,stdout-path' has been deprecated for some time in favor of
'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
Search and replace the one occurrence with 'stdout-path'.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
'linux,stdout-path' has been deprecated for some time in favor of
'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'.
Search and replace all the of occurrences with 'stdout-path'.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform has one SC2731 PMIC, and the SC2731
PMIC integrates all mobile handset power management, audio codec,
battery management and user interface support function in a single
chip.
This patch adds the SC2731 dts file, as well as adding the RTC and
regulator device node for this PMIC.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform has two DMA controllers, one is located
on the ap-ahb system, and another one is located on the agcp system.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the watchdog device node for Spreadtrum SC9860 platform to
watch the system's stability.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We will use one always-on timer to be the broadcast device, thus add
the timer device node for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the pin controller device node for Spreadtrum
SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We will access the PMIC through ADI controller, thus this patch adds
the ADI device node for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Spreadtrum SC9860 platform only has one hardware spinlock device,
which is located on AON system of Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "DaVinci DT support enhancements for v4.17" from Sekhar Nori:
* Lego EV3 gains firmware recovery mode support
* Miscellaneous non-critical clean-up
* tag 'davinci-for-v4.17/dt' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: add chosen and SPI alias
ARM: dts: da850-lego-ev3: use a correct fallback for at24 compatible
ARM: dts: da850-lego-ev3: Add node for reboot modes
OF graph describes MHL data lanes between MHL and respective USB
connector.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since USB connector bindings are available we can describe it on TM2(e).
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add node for the hardware crypto acceleration used in the artpec6 SoC.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PCIe controller in the artpec6 SoC supports both root complex and
endpoint mode, however, the controller can only be used in one of the
modes.
Both pci nodes are disabled by default. A DTS file can enable one of
them, depending on what mode it wants to run.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add nodes for the nbpfaxi DMA controllers used in the artpec6 SoC,
and start using them for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add node for the pin controller used in the artpec6 SoC,
and start using it for the exising UARTs.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The snps,dwc-qos-ethernet binding is still supported as a glue layer
in the stmmac driver.
However, since the snps,dwc-qos-ethernet binding is now deprecated,
migrate to stmmac's native binding.
At the same time, enable features supported by the stmmac driver,
such as PTP, LPI, and an additional tx queue.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove 0x prefix from clkctrl unit address.
This silences the following dtc warning:
Warning (unit_address_format):
Node /clkctrl@0xf8000000 unit name should not have leading "0x"
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There has never been an artpec6 devboard produced
with less than 1 GiB RAM.
Increase the default value to 1 GiB RAM, so that we
can netboot with large initramfs without going OOM.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Accesses via 0x80000000 go through the ACP instead of using the DDR
directly.
Unfortunately the ACP has proven to be the cause of complete system
hangs. Disabling the ACP makes these problems go away.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
