Dave Marchevsky says:
====================
BPF Refcount followups 2: owner field
This series adds an 'owner' field to bpf_{list,rb}_node structs, to be
used by the runtime to determine whether insertion or removal operations
are valid in shared ownership scenarios. Both the races which the series
fixes and the fix itself are inspired by Kumar's suggestions in [0].
Aside from insertion and removal having more reasons to fail, there are
no user-facing changes as a result of this series.
* Patch 1 reverts disabling of bpf_refcount_acquire so that the fixed
logic can be exercised by CI. It should _not_ be applied.
* Patch 2 adds internal definitions of bpf_{rb,list}_node so that
their fields are easier to access.
* Patch 3 is the meat of the series - it adds 'owner' field and
enforcement of correct owner to insertion and removal helpers.
* Patch 4 adds a test based on Kumar's examples.
* Patch 5 disables the test until bpf_refcount_acquire is re-enabled.
* Patch 6 reverts disabling of test added in this series
logic can be exercised by CI. It should _not_ be applied.
[0]: https://lore.kernel.org/bpf/d7hyspcow5wtjcmw4fugdgyp3fwhljwuscp3xyut5qnwivyeru@ysdq543otzv2/
Changelog:
v1 -> v2: lore.kernel.org/bpf/20230711175945.3298231-1-davemarchevsky@fb.com/
Patch 2 ("Introduce internal definitions for UAPI-opaque bpf_{rb,list}_node")
* Rename bpf_{rb,list}_node_internal -> bpf_{list,rb}_node_kern (Alexei)
Patch 3 ("bpf: Add 'owner' field to bpf_{list,rb}_node")
* WARN_ON_ONCE in __bpf_list_del when node has wrong owner. This shouldn't
happen, but worth checking regardless (Alexei, offline convo)
* Continue previous patch's renaming changes
====================
Link: https://lore.kernel.org/r/20230718083813.3416104-1-davemarchevsky@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds a runnable version of one of the races described by
Kumar in [0]. Specifically, this interleaving:
(rbtree1 and list head protected by lock1, rbtree2 protected by lock2)
Prog A Prog B
======================================
n = bpf_obj_new(...)
m = bpf_refcount_acquire(n)
kptr_xchg(map, m)
m = kptr_xchg(map, NULL)
lock(lock2)
bpf_rbtree_add(rbtree2, m->r, less)
unlock(lock2)
lock(lock1)
bpf_list_push_back(head, n->l)
/* make n non-owning ref */
bpf_rbtree_remove(rbtree1, n->r)
unlock(lock1)
The above interleaving, the node's struct bpf_rb_node *r can be used to
add it to either rbtree1 or rbtree2, which are protected by different
locks. If the node has been added to rbtree2, we should not be allowed
to remove it while holding rbtree1's lock.
Before changes in the previous patch in this series, the rbtree_remove
in the second part of Prog A would succeed as the verifier has no way of
knowing which tree owns a particular node at verification time. The
addition of 'owner' field results in bpf_rbtree_remove correctly
failing.
The test added in this patch splits "Prog A" above into two separate BPF
programs - A1 and A2 - and uses a second mapval + kptr_xchg to pass n
from A1 to A2 similarly to the pass from A1 to B. If the test is run
without the fix applied, the remove will succeed.
Kumar's example had the two programs running on separate CPUs. This
patch doesn't do this as it's not necessary to exercise the broken
behavior / validate fixed behavior.
[0]: https://lore.kernel.org/bpf/d7hyspcow5wtjcmw4fugdgyp3fwhljwuscp3xyut5qnwivyeru@ysdq543otzv2
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Suggested-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20230718083813.3416104-5-davemarchevsky@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
As described by Kumar in [0], in shared ownership scenarios it is
necessary to do runtime tracking of {rb,list} node ownership - and
synchronize updates using this ownership information - in order to
prevent races. This patch adds an 'owner' field to struct bpf_list_node
and bpf_rb_node to implement such runtime tracking.
The owner field is a void * that describes the ownership state of a
node. It can have the following values:
NULL - the node is not owned by any data structure
BPF_PTR_POISON - the node is in the process of being added to a data
structure
ptr_to_root - the pointee is a data structure 'root'
(bpf_rb_root / bpf_list_head) which owns this node
The field is initially NULL (set by bpf_obj_init_field default behavior)
and transitions states in the following sequence:
Insertion: NULL -> BPF_PTR_POISON -> ptr_to_root
Removal: ptr_to_root -> NULL
Before a node has been successfully inserted, it is not protected by any
root's lock, and therefore two programs can attempt to add the same node
to different roots simultaneously. For this reason the intermediate
BPF_PTR_POISON state is necessary. For removal, the node is protected
by some root's lock so this intermediate hop isn't necessary.
Note that bpf_list_pop_{front,back} helpers don't need to check owner
before removing as the node-to-be-removed is not passed in as input and
is instead taken directly from the list. Do the check anyways and
WARN_ON_ONCE in this unexpected scenario.
Selftest changes in this patch are entirely mechanical: some BTF
tests have hardcoded struct sizes for structs that contain
bpf_{list,rb}_node fields, those were adjusted to account for the new
sizes. Selftest additions to validate the owner field are added in a
further patch in the series.
[0]: https://lore.kernel.org/bpf/d7hyspcow5wtjcmw4fugdgyp3fwhljwuscp3xyut5qnwivyeru@ysdq543otzv2
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Suggested-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Link: https://lore.kernel.org/r/20230718083813.3416104-4-davemarchevsky@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Structs bpf_rb_node and bpf_list_node are opaquely defined in
uapi/linux/bpf.h, as BPF program writers are not expected to touch their
fields - nor does the verifier allow them to do so.
Currently these structs are simple wrappers around structs rb_node and
list_head and linked_list / rbtree implementation just casts and passes
to library functions for those data structures. Later patches in this
series, though, will add an "owner" field to bpf_{rb,list}_node, such
that they're not just wrapping an underlying node type. Moreover, the
bpf linked_list and rbtree implementations will deal with these owner
pointers directly in a few different places.
To avoid having to do
void *owner = (void*)bpf_list_node + sizeof(struct list_head)
with opaque UAPI node types, add bpf_{list,rb}_node_kern struct
definitions to internal headers and modify linked_list and rbtree to use
the internal types where appropriate.
Signed-off-by: Dave Marchevsky <davemarchevsky@fb.com>
Link: https://lore.kernel.org/r/20230718083813.3416104-3-davemarchevsky@fb.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Luo Jie says:
====================
net: phy: at803x: support qca8081 1G version chip
This patch series add supporting qca8081 1G version chip, the 1G version
chip can be identified by the register mmd7.0x901d bit0.
In addition, qca8081 does not support 1000BaseX mode and the sgmii fifo
reset is added on the link changed, which assert the fifo on the link
down, deassert the fifo on the link up.
Changes in v1:
* switch to use genphy_c45_pma_read_abilities.
* remove the patch [remove 1000BaseX mode of qca8081].
* move the sgmii fifo reset to link_change_notify.
Changes in v2:
* split the qca8081 1G chip support patch.
* improve the slave seed config, disable it if master preferred.
Changes in v3:
* fix the comments.
* add the help function qca808x_has_fast_retrain_or_slave_seed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The qca8081 sgmii fifo needs to be reset on link down and
released on the link up in case of any abnormal issue
such as the packet blocked on the PHY.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fast retrain and slave seed configs are only applicable when the 2.5G
ability is supported.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qca8081 1G chip version does not support 2.5 capability, which
is distinguished from qca8081 2.5G chip according to the bit0 of
register mmd7.0x901d, the 1G version chip also has the same PHY ID
as the normal qca8081 2.5G chip.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8081 is the single port PHY, the slave prefer mode is used
by default.
if the phy master perfer mode is configured, the slave seed
configuration should not be enabled, since the slave seed
enablement is for making PHY linked as slave mode easily.
disable slave seed if the master mode is preferred.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
merge the seed enablement and seed value configuration into
one function, since the random seed value is needed to be
configured when the seed is enabled.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8081 PHY supports to use genphy_c45_pma_read_abilities for
getting the PHY features supported except for the autoneg ability
but autoneg ability exists in MDIO_STAT1 instead of MMD7.1, add it
manually after calling genphy_c45_pma_read_abilities.
Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vignesh Viswanathan says:
====================
net: qrtr: Few fixes in QRTR
Add fixes in QRTR ns to change server and nodes radix tree to xarray to
avoid a use-after-free while iterating through the server or nodes
radix tree.
Also fix the destination port value for IPCR control buffer on older
targets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The destination port value in the IPCR control buffer on older
targets is 0xFFFF. Handle the same by updating the dst_port to
QRTR_PORT_CTRL.
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a use after free scenario while iterating through the nodes
radix tree despite the ns being a single threaded process. This can
happen when the radix tree APIs are not synchronized with the
rcu_read_lock() APIs.
Convert the radix tree for nodes to xarray to take advantage of the
built in rcu lock usage provided by xarray.
Signed-off-by: Chris Lew <quic_clew@quicinc.com>
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a use after free scenario while iterating through the servers
radix tree despite the ns being a single threaded process. This can
happen when the radix tree APIs are not synchronized with the
rcu_read_lock() APIs.
Convert the radix tree for servers to xarray to take advantage of the
built in rcu lock usage provided by xarray.
Signed-off-by: Chris Lew <quic_clew@quicinc.com>
Signed-off-by: Vignesh Viswanathan <quic_viswanat@quicinc.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Justin Chen says:
====================
Brcm ASP 2.0 Ethernet Controller
Add support for the Broadcom ASP 2.0 Ethernet controller which is first
introduced with 72165.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for wake on network filters. The max match is 256 bytes.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Wake-On-Lan magic packet and magic packet with password.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Broadcom ASP 2.0 Ethernet controller which is first
introduced with 72165. This controller features two distinct Ethernet
ports that can be independently operated.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename local `struct fec_enet_private *adapter` to `fep` in `fec_ptp_gettime()` to match the rest of the driver
Signed-off-by: Csókás Bence <csokas.bence@prolan.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spotted this trivial spell mistake while casually reading
the google GVE driver code.
Signed-off-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata says:
====================
mlxsw: Manage RIF across PVID changes
The mlxsw driver currently makes the assumption that the user applies
configuration in a bottom-up manner. Thus netdevices need to be added to
the bridge before IP addresses are configured on that bridge or SVI added
on top of it. Enslaving a netdevice to another netdevice that already has
uppers is in fact forbidden by mlxsw for this reason. Despite this safety,
it is rather easy to get into situations where the offloaded configuration
is just plain wrong.
As an example, take a front panel port, configure an IP address: it gets a
RIF. Now enslave the port to the bridge, and the RIF is gone. Remove the
port from the bridge again, but the RIF never comes back. There is a number
of similar situations, where changing the configuration there and back
utterly breaks the offload.
The situation is going to be made better by implementing a range of replays
and post-hoc offloads.
In this patch set, address the ordering issues related to creation of
bridge RIFs. Currently, mlxsw has several shortcomings with regards to RIF
handling due to PVID changes:
- In order to cause RIF for a bridge device to be created, the user is
expected first to set PVID, then to add an IP address. The reverse
ordering is disallowed, which is not very user-friendly.
- When such bridge gets a VLAN upper whose VID was the same as the existing
PVID, and this VLAN netdevice gets an IP address, a RIF is created for
this netdevice. The new RIF is then assigned to the 802.1Q FID for the
given VID. This results in a working configuration. However, then, when
the VLAN netdevice is removed again, the RIF for the bridge itself is
never reassociated to the PVID.
- PVID cannot be changed once the bridge has uppers. Presumably this is
because the driver does not manage RIFs properly in face of PVID changes.
However, as the previous point shows, it is still possible to get into
invalid configurations.
This patch set addresses these issues and relaxes some of the ordering
requirements that mlxsw had. The patch set proceeds as follows:
- In patch #1, pass extack to mlxsw_sp_br_ban_rif_pvid_change()
- To relax ordering between setting PVID and adding an IP address to a
bridge, mlxsw must be able to request that a RIF is created with a given
VLAN ID, instead of trying to deduce it from the current netdevice
settings, which do not reflect the user-requested values yet. This is
done in patches #2 and #3.
- Similarly, mlxsw_sp_inetaddr_bridge_event() will need to make decisions
based on the user-requested value of PVID, not the current value. Thus in
patches #4 and #5, add a new argument which carries the requested PVID
value.
- Finally in patch #6 relax the ban on PVID changes when a bridge has
uppers. Instead, add the logic necessary for creation of a RIF as a
result of PVID change.
- Relevant selftests are presented afterwards. In patch #7 a preparatory
helper is added to lib.sh. Patches #8, #9, #10 and #11 include selftests
themselves.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests whether addition and deletion of a VLAN upper that coincides
with the current PVID setting throws off forwarding.
This selftests is specifically geared towards offloading drivers. In
particular, mlxsw used to fail this selftest, and an earlier patch in this
patchset fixes the issue. However, there's nothing HW-specific in the test
itself (it absolutely is supposed to pass on SW datapath), and therefore it
is put into the generic forwarding directory.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This tests whether changes to PVID that coincide with an existing VLAN
upper throw off forwarding. This selftests is specifically geared towards
offloading drivers, but since there's nothing HW-specific in the test
itself (it absolutely is supposed to pass on SW datapath), it is put into
the generic forwarding directory.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an alternative path involving VLAN 777 instead of the current 555. Then
add tests that verify that marking 777 as PVID makes the 555 path not work,
and the 777 path work.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test relies on PVID being configured on the bridge itself. Thus when
it is deconfigured, the system should lose the ability to forward traffic.
Later when it is added again, the ability to forward traffic should be
regained. Add tests to exercise these configuration changes and verify
results.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two helpers to run a ping test that succeeds when the pings themselves
fail.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlxsw has several shortcomings with regards to RIF handling due
to PVID changes:
- In order to cause RIF for a bridge device to be created, the user is
expected first to set PVID, then to add an IP address. The reverse
ordering is disallowed, which is not very user-friendly.
- When such bridge gets a VLAN upper whose VID was the same as the existing
PVID, and this VLAN netdevice gets an IP address, a RIF is created for
this netdevice. The new RIF is then assigned to the 802.1Q FID for the
given VID. This results in a working configuration. However, then, when
the VLAN netdevice is removed again, the RIF for the bridge itself is
never reassociated to the VLAN.
- PVID cannot be changed once the bridge has uppers. Presumably this is
because the driver does not manage RIFs properly in face of PVID changes.
However, as the previous point shows, it is still possible to get into
invalid configurations.
In this patch, add the logic necessary for creation of a RIF as a result of
PVID change. Moreover, when a VLAN upper is created whose VID matches lower
PVID, do not create RIF for this netdevice.
These changes obviate the need for ordering of IP address additions and
PVID configuration, so stop forbidding addition of an IP address to a
PVID-less bridge. Instead, bail out quietly. Also stop preventing PVID
changes when the bridge has uppers.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For purposes of replay, mlxsw_sp_inetaddr_bridge_event() will need to make
decisions based on the proposed value of PVID. Querying PVID reveals the
current settings, not the in-flight values that the user requested and that
the notifiers are acting upon. Add a parameter, lower_pvid, which carries
the proposed PVID of the lower bridge, or -1 if the lower is not a bridge.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge branch of the dispatch in this function is going to get more
code and will need curly braces. Per the doctrine, that means the whole
if-else chain should get them.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when an IP address is added to a bridge that has no PVID, the
operation is rejected. An IP address addition is interpreted as a request
to create a RIF for the bridge device, but without a PVID there is no VLAN
for which the RIF should be created. Thus the correct way to create a RIF
for a bridge as a user is to first add a PVID, and then add the IP address.
Ideally this ordering requirement would not exist. RIF would be created
either because an IP address is added, or because a PVID is added,
depending on which comes last.
For that, the switchdev code (which notices the PVID change request) must
be able to request that a RIF is created with a given VLAN ID, because at
the time that the PVID notification is distributed, the PVID setting is not
yet visible for querying.
Therefore when creating a VLAN-based RIF, use mlxsw_sp_rif_params.vid to
communicate the VID, and do not determine it ad-hoc in the fid_get
callback.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fid_get callback is called to allocate a FID for the newly-created RIF.
In a following patch, the fid_get implementation for VLANs will be modified
to take the VLAN ID from the parameters instead of deducing it from the
netdevice. To that end, propagate the RIF parameters to the fid_get
callback.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the reason for rejection of PVID manipulation is dumped to
syslog, and a generic -EBUSY is returned to the userspace. But
switchdev_handle_port_obj_add(), through which we get to
mlxsw_sp_port_vlans_add(), handles extack just fine, and we can pass the
message this way.
This improves visibility into reasons why the request to change PVID
was rejected. Before the change:
# bridge vlan add dev br vid 2 self pvid untagged
RTNETLINK answers: Device or resource busy
(plus a syslog line)
After the change:
# bridge vlan add dev br vid 2 self pvid untagged
Error: mlxsw_spectrum: Can't change PVID, it's used by router interface.
Note that this particular error message is going away in the following
patches. However the ability to pass error messages through extack will be
useful more broadly for communicating in particular reasons why a RIF
failed to be created.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sabrina Dubroca says:
====================
net: add MACsec offload selftests
Patch 1 adds MACsec offload to netdevsim (unchanged from v2).
Patch 2 adds a corresponding selftest to the rtnetlink testsuite.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the IPsec offload test, this requires netdevsim.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the kernel is compiled with MACsec support, add the
NETIF_F_HW_MACSEC feature to netdevsim devices and implement
macsec_ops.
To allow easy testing of failure from the device, support is limited
to 3 SecY's per netdevsim device, and 1 RXSC per SecY.
v2:
- nsim_macsec_add_secy, return -ENOSPC if secy_count isn't full but
we can't find an empty slot (Simon Horman)
- add sci_to_cpu to make sparse happy (Simon Horman)
- remove set but not used secy variable (kernel test robot and
Simon Horman)
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The checks in question were introduced by:
commit 6b4db2e528 ("devlink: Fix use-after-free after a failed reload").
That fixed an issue of reload with mlxsw driver.
Back then, that was a valid fix, because there was a limitation
in place that prevented drivers from registering/unregistering params
when devlink instance was registered.
It was possible to do the fix differently by changing drivers to
register/unregister params in appropriate places making sure the ops
operate only on memory which is allocated and initialized. But that,
as a dependency, would require to remove the limitation mentioned above.
Eventually, this limitation was lifted by:
commit 1d18bb1a4d ("devlink: allow registering parameters after the instance")
Also, the alternative fix (which also fixed another issue) was done by:
commit 74cbc3c03c ("mlxsw: spectrum_acl_tcam: Move devlink param to TCAM code").
Therefore, the checks are no longer relevant. Each driver should make
sure to have the params registered only when the memory the ops
are working with is allocated and initialized.
So remove the checks.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
Convert mv88e6xxx to phylink_pcs
This series (previously posted with further patches on the 26 June as
RFC) converts mv88e6xxx to phylink_pcs, and thus moves it from being
a pre-March 2020 legacy driver.
The first four patches lay the ground-work for the conversion by
adding four new methods to the phylink_pcs operations structure:
pcs_enable() - called when the PCS is going to start to be used
pcs_disable() - called when the PCS is no longer being used
pcs_pre_config() - called before the MAC configuration method
pcs_post_config() - called after the MAC configuration method
Both of these are necessary for some of the mv88e639x
workarounds.
We also add the ability to inform phylink of a change to the PCS
state without involving the MAC later, by providing
phylink_pcs_change() which takes a phylink_pcs structure rather than
a phylink structure. phylink maintains which instance the PCS is
conencted to, so internally it can do the right thing when the PCS
is in-use.
Then we provide some additional mdiobus and mdiodev accessors that
we will be using in the new PCS drivers.
The changes for mv88e6xxx follow, and the first one needs to be
explicitly pointed out - we (Andrew and myself) have both decided that
all possible approaches to maintaining backwards compatibility with DT
have been exhaused - everyone has some objection to everything that
has been proposed. So, after many years of trying, we have decided
that this is just an impossibility, and with this patch, we are now
intentionally and knowingly breaking any DT that does not specify the
CPU and DSA port fixed-link parameters. Hence why Andrew has recently
been submitting DT update patches. It is regrettable that it has come
to this.
Following this, we start preparing 88e6xxx for phylink_pcs conversion
by padding the mac_select_pcs() DSA method, and the internal hooks to
create and tear-down PCS instances. Rather than bloat the already very
large mv88e6xxx_ops structure, I decided that it would be better that
the new internal chip specific PCS methods are all grouped within their
own structure - and this structure can be declared in the PCS drivers
themselves.
Then we have the actual conversion patches, one for each family of PCS.
Lastly, we clean up the driver after conversion, removing all the now
redundant code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that mv88e6xxx is completely converted to using phylink_pcs
support, we have no need for the serdes methods. Remove all this
infrastructure. Also remove the __maybe_unused from
mv88e6xxx_pcs_select().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the 88E6390, 88E6390X, and 88E6393X family of switches to use
the phylink_pcs infrastructure.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the 88E6352 SERDES code to use the phylink_pcs infrastructure.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
