[Why]
During Z10, root clock gating and memory low power registers needs to
to be restored if optimization is enabled in driver.
[How]
Added new DMUB boot option for root clock gating and memory low power.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPO is only used for DP2.0. HPO HW control should be
disable when not being used to save power.
[How]
Shutdown HPO HW control during init hw.
Shutdown HPO HW control during stream disable.
Enable HPO HW control during stream enable if DP2.0.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
State can be cleared without removing individual streams (by
calling dc_remove_stream_from_ctx()). This can leave the
encoder assignment module in an incoherent state and cause
future assignments to be incorrect.
[How]
Clear encoder assignments when committing 0 streams or
re-initializing hardware.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In scenario when 1 display connected with pipe split (2 pipes in use)
and 3 new displays simultaneously hotplugged via MST hub (4 pipes in use),
mpcc may get reprogram to other vtg, remaining busy.
In this case waiting for mpcc idle timeouts with error like this:
[drm] REG_WAIT timeout 1us * 100000 tries - mpc2_assert_idle_mpcc
RIP: 0010:mpc2_assert_mpcc_idle_before_connect
Call Trace:
dcn20_update_mpcc
dcn20_program_front_end_for_ctx
dc_commit_state
amdgpu_dm_atomic_commit_tail
...
[How]
Add pipe split change condition to disable dangling plane.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It was found that the system would hang on a dummy pstate when playing
4k60 videos on a 1080p 390Hz monitor.
[HOW]
Properly select the dummy_pstate_latency_ms when firmware assisted
memory clock switching is enabled instead of assuming that the highest
latency would work for every monitor timing.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Felipe Clark <felclark@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
If timing and bpp of displays on mst hub are not changed,
pbn, slot_num for displays should not be changed. Linux
user mode may initiate atomic_check with different display
configuration after set mode finished. This will call to
amdgpu_dm to re-compute payload, slot_num of displays and
saved to dm_connect_state. stream->timing.flags.dsc, pbn,
slot_num are updated to values which may be different from
that were used for set mode. when dsc hub with 3 4k@60hz dp
connected, 3 dsc engines are enabled. timing.flags.dsc = 1.
timing.flags.dsc are changed to 0 due to atomic check. when
dsc hub is unplugged, amdgpu driver check timing.flags.dsc
for last mode set and find out flags.dsc = 0, then does not
disable dsc.
[HOW]
check status of displays on dsc mst hubs. re-compute pbn,
slot_num, timing.flags.dsc only if there is mode, connect
or enable/disable change.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Hersen Wu <hersenwu@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This better aligns that the caller can make a mistake with the buffer
and -EINVAL should be returned, but if the hardware doesn't support
the feature it should be -EOPNOTSUPP.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was added by commit bd8dcea93a ("drm/amd/pm: add callbacks to
read/write sysfs file pp_power_profile_mode") but the feature was
deprecated from PMFW. Remove it from the driver.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previously Renoir compiler gfx target version was forced to Raven.
Update driver side for completeness.
Signed-off-by: Graham Sider <Graham.Sider@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is more useful when talking to the SMU team to have the information
in this format, save one less step to manually do it.
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If some pages fail to migrate to system memory, don't update
prange->actual_loc = 0. This prevents endless CPU page faults after
partial migration failures due to contested page locks.
Migration to RAM must be complete during migrations from VRAM to VRAM and
during evictions. Implement retry and fail if the migration to RAM fails.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stack and heap pages tend to be shared by many small allocations.
Concurrent access by CPU and GPU is therefore likely, which can lead to
thrashing. Avoid this by setting the preferred location to system memory.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The preferred location should be used as the migration destination
whenever it is accessible by the faulting GPU. System memory is always
accessible. Peer memory is accessible if it's in the same XGMI hive.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aldebaran has different register mask definitions for
regiter MC_VM_XGMI_LFB_CNTL. Use the correct masks
to interpret fields of this register.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In advance tdr mode, the real bad job will be resubmitted twice, while
in drm_sched_resubmit_jobs_ext, there's a dma_fence_put, so the bad job
is put one more time than other jobs.
[How]
Adding dma_fence_get before resbumit job in
amdgpu_device_recheck_guilty_jobs and put the fence for normal jobs
Signed-off-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- DPIA MST slot registers are not programmed during payload
allocation and hence MST does not work with DPIA.
- HPD RX interrupts are not handled for DPIA.
[How]
- Added inbox command to program the MST slots whenever
payload allocation happens for DPIA links.
- Added support for handling HPD RX interrupts
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CVE-2021-42327 was fixed by:
commit f23750b5b3
Author: Thelford Williams <tdwilliamsiv@gmail.com>
Date: Wed Oct 13 16:04:13 2021 -0400
drm/amdgpu: fix out of bounds write
but amdgpu_dm_debugfs.c contains more of the same issue so fix the
remaining ones.
v2:
* Add missing fix in dp_max_bpc_write (Harry Wentland)
Fixes: 918698d5c2 ("drm/amd/display: Return the number of bytes parsed than allocated")
Signed-off-by: Patrik Jakobsson <pjakobsson@suse.de>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMUB binary is common for both A0 and B0. Hence, driver should
notify FW about the support for DPIA in B0.
[How]
Added dpia_supported bit in dmub_fw_boot_options and will be set
only for B0.
Assign dpia_supported to true before dm_dmub_hw_init
in B0 case.
v2: fix build without CONFIG_DRM_AMD_DC_DCN (Alex)
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Notify data from outbox corrupt, the notify type should be 2 (HPD) instead of 0
(No data). We copied the address instead of the value. The memory might be
freed in the end of outbox IRQ
[How]
We should allocate the memory of notify and copy the whole content from outbox to
hpd handle function
Fixes: 88f52b1fff ("drm/amd/display: Support for SET_CONFIG processing with DMUB")
Signed-off-by: Jude Shih <shenshih@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
A deadlock in the kernel occurs when we fallback from the V3 to V2
add_topology_to_display or remove_topology_to_display because they
both try to acquire the dtm_mutex but recursive locking isn't
supported on mutex_lock().
[How]
Make the mutex_lock/unlock more fine grained and move them up such that
they're only required for the psp invocation itself.
Fixes: bf62221e9d ("drm/amd/display: Add DCN3.1 HDCP support")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On certain configs, SMU clock table voltages don't match which cause parser
to behave incorrectly by leaving dcfclk and socclk table entries unpopulated.
[HOW]
Currently the function that finds the corresponding clock for a given voltage
only checks for exact voltage level matches. In the case that no match gets
found, parser now falls back to searching for the max clock which meets the
requested voltage (i.e. its corresponding voltage is below requested).
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We have a regression that cause maximize lane settings to use
uninitialized data from unused lanes.
This will cause link training to fail for 1 or 2 lanes because the lane
adjust is populated incorrectly sometimes.
v2: fix build without CONFIG_DRM_AMD_DC_DCN (Alex)
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
option 1: disallow different lanes to have different lane settings
option 2: dpcd lane settings will always use the same hw lane settings
even if it doesn't match requested lane adjust
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
As DP features expands, we have encountered many situations where we
must configure a different DPCD lane setting from hw lane settings we
output. The change is to decouple hw lane settings from dpcd lane
settings to provide flexibility to configure dpcd and hw individually.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Decouple lane settings decision logic all to its own function. The
function takes in lane adjust array and link training settings and
decide what hw lane setting and dpcd lane setting should be used.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
revision 8 SCR requires DP Source to write TPS2 and FFE lane adjustment
in one 5 byte write aux transaction.
It specifies to read aux rd interval value as soon as we turn on TPS1
pattern.
Cc: Wayne Lin <wayne.lin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
