1. Rename securedisplay_cmd to ta_securedisplay_cmd.
2. Rename ta_securedisplay_max_phy to ta_securedisplay_phy_ID.
3. update securedisplay_cmd to ta_securedisplay_cmd
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Shane Xiao <shane.xiao@amd.com>
Reviewed-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pipe_ctx pointer cannot be NULL when getting the address of
an element of the pipe_ctx array. Moreover, the MAX_PIPES is
defined as 6, so pipe_ctx is not NULL after the loop either.
Detected using the static analysis tool - Svace.
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_ras_block_late_init will be invoked in IP
specific ras_late_init call as a common helper for
all the IP blocks.
However, when amdgpu_ras_block_late_init call
amdgpu_ras_query_error_count to query ras error
counters, amdgpu_ras_query_error_count queries
all the IP blocks that support ras query interface.
This results to wrong error counters cached in
software copies when there are ras errors detected
at time zero or warm reset procedure. i.e., in
sdma_ras_late_init phase, it counts on sdma/mmhub
errors, while, in mmhub_ras_late_init phase, it
still counts on sdma/mmhub errors.
The change updates amdgpu_ras_query_error_count
interface to allow query specific ip error counter.
It introduces a new input parameter: query_info. if
query_info is NULL, it means query all the IP blocks,
otherwise, only query the ip block specified by
query_info.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HPD signals on DVI ports can be fired off before the pins required for
DDC probing actually make contact, due to the pins for HPD making
contact first. This results in a HPD signal being asserted but DDC
probing failing, resulting in hotplugging occasionally failing.
Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.
Signed-off-by: xurui <xurui@kylinos.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-misc-next for v6.3:
UAPI Changes:
* connector: Support analog-TV mode property
* media: Add MEDIA_BUS_FMT_RGB565_1X24_CPADHI,
MEDIA_BUS_FMT_RGB666_1X18 and MEDIA_BUS_FMT_RGB666_1X24_CPADHI
Cross-subsystem Changes:
* dma-buf: Documentation fixes
* i2c: Introduce i2c_client_get_device_id() helper
Core Changes:
* Improve support for analog TV output
* bridge: Remove unused drm_bridge_chain functions
* debugfs: Add per-device helpers and convert various DRM drivers
* dp-mst: Various fixes
* fbdev emulation: Always pick 32 bpp as default
* KUnit: Add tests for managed helpers; Various cleanups
* panel-orientation: Add quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
* TTM: Open-code ttm_bo_wait() and remove the helper
Driver Changes:
* Fix preferred depth and bpp values throughout DRM drivers
* Remove #CONFIG_PM guards throughout DRM drivers
* ast: Various fixes
* bridge: Implement i2c's probe_new in various drivers; Fixes; ite-it6505:
Locking fixes, Cache EDID data; ite-it66121: Support IT6610 chip,
Cleanups; lontium-tl9611: Fix HDMI on DragonBoard 845c; parade-ps8640:
Use atomic bridge functions
* gud: Convert to DRM shadow-plane helpers; Perform flushing synchronously
during atomic update
* ili9486: Support 16-bit pixel data
* imx: Split off IPUv3 driver; Various fixes
* mipi-dbi: Convert to DRM shadow-plane helpers plus rsp driver changes;i
Support separate I/O-voltage supply
* mxsfb: Depend on ARCH_MXS or ARCH_MXC
* omapdrm: Various fixes
* panel: Use ktime_get_boottime() to measure power-down delay in various
drivers; Fix auto-suspend delay in various drivers; orisetech-ota5601a:
Add support
* sprd: Cleanups
* sun4i: Convert to new TV-mode property
* tidss: Various fixes
* v3d: Various fixes
* vc4: Convert to new TV-mode property; Support Kunit tests; Cleanups;
dpi: Support RGB565 and RGB666 formats; dsi: Convert DSI driver to
bridge
* virtio: Improve tracing
* vkms: Support small cursors in IGT tests; Various fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y7QIwlfElAYWxRcR@linux-uq9g
Fix all kernel-doc warnings in dc/core/dc.c:
dc.c:385: warning: missing initial short description on line:
* dc_stream_adjust_vmin_vmax:
dc.c:392: warning: contents before sections
dc.c:399: warning: No description found for return value of 'dc_stream_adjust_vmin_vmax'
dc.c:434: warning: Excess function parameter 'adjust' description in 'dc_stream_get_last_used_drr_vtotal'
dc.c:434: warning: No description found for return value of 'dc_stream_get_last_used_drr_vtotal'
dc.c:574: warning: No description found for return value of 'dc_stream_configure_crc'
dc.c:1746: warning: No description found for return value of 'dc_commit_state_no_check'
dc.c:4991: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* dc_extended_blank_supported 0 Decide whether extended blank is supported
dc.c:4991: warning: missing initial short description on line:
* dc_extended_blank_supported 0 Decide whether extended blank is supported
dc.c:4723: warning: Function parameter or member 'dc' not described in 'dc_enable_dmub_outbox'
dc.c:4926: warning: Function parameter or member 'dc' not described in 'dc_process_dmub_dpia_hpd_int_enable'
dc.c:4926: warning: Function parameter or member 'hpd_int_enable' not described in 'dc_process_dmub_dpia_hpd_int_enable'
12 warnings
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Hamza Mahfooz <hamza.mahfooz@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: amd-gfx@lists.freedesktop.org
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We skip dsc_validation on pipes that are underlays, but in the
acquire_dsc code we don't have this check.
In certain conditions (when underlay pipe index is lower) we will assign
the dsc resource to the underlay pipe and skip the base pipe.
Now during dsc_validation we will skip the underlay pipe (this has the
dsc resource) but try to validate the base pipe(this doesn't have a dsc
resource) due to this mismatch we hit a NULLPTR
[How]
In the acquire_dsc add a check for underlay pipe so we
don't acquire a dsc resource for this pipe. This will match the
acquire/validation conditions.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Hersen Wu <Hersenxs.Wu@amd.com>
Acked-by: Praful Swarnakar <Praful.Swarnakar@amd.com>
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For GFX 11.0.3, Due to security policy, there is no way to check UcFatalEn
field of UMCCH0_0_GeccCtrl to identify UMC poison mode. This is workaround
force set umc poison mode as 1 for GFX 11.0.3
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
By moving bw_ctx field to the end of the dc_state the state can be
cleared more efficiently without resulting in large DML memcpy
operations, resulting in better mode enumeration performance on some
platforms.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
ignore_msa_timing_param is used by SubVP logic to determine if SubVP
+ DRR is possible. Linux does not support freesync on multi display
config, which results in incorrect assumption of VRR support if we
set this parameter when VRR is supported, but not enabled.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
During DP2.1 LL CTS if test equipment requests to change between
DP2.1 and DP1.4 link rates, we need to swap between HPO and DIO
encoders by remapping encoder resource.
[how]
Add a function dc resource to update encoder resources and toggle
dpms state for all enabled stream associated witht the link under test.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Pixel rate div depends on the type of encoder
that we are enabling stream with. If we swap between
HPO and DIO encoder at the time we call enable stream
for the new encoder, we must reprogram pixel rate div
based on the new encoder type.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On some monitors we see a brief flash of corruption during the
monitor disable sequence caused by FIFO being disabled in the middle
of an active DP stream.
[How]
Wait until DP vid stream is disabled before turning off the FIFO.
The FIFO reset on DP unblank should take care of clearing any FIFO
error, if any.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Syed Hassan <Syed.Hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DCN301 resource function is missing function pointer to
handle cases with unknown plane state.
This causes assertion when global state is validated while
using swizzle parameter as “DC_UNKNOWN”
[How]
Add function pointer to handle and patch cases when plane
state is unknown.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Swapnil Patel <Swapnil.Patel@amd.com>
Reviewed-by: Sung joon Kim <Sungjoon.Kim@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
- Proper phantom pipe disable sequence was missing in
commit_planes_for_stream
- If disabling phantom pipe, turn on phantom OTG first, and turn
off the phantom OTG after the plane is disabled
- Also update sequence for enabling / disabling phantom streams
(apply_ctx_to_hw). When enabling phantom pipes, enable before
doing front end programming for phantom pipes. If disabling
phantom pipes, disable after front end programming (i.e. after
phantom plane disable)
- TODO: Still need to properly handle transition case when a phantom
pipe is transitioned directly into a real pipe (need to fully disable
the phantom pipe first)
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
- Need error message when failing to allocating secure_display_ctx.
- Need to check if secure display context in psp is initialized or not
before using it.
[How]
- Add error message when memory allocation fail.
- Add check before accessing psp secure display context.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SwathSizePerSurfaceY[] and SwathSizePerSurfaceC[] values are uninitialized
because we are using += instead of = operator.
[How]
Assign values in loop with = operator.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Samson Tam <samson.tam@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
multiple display hdcp are enabled within event_property_validate,
event_property_update by looping all displays on mst hub. when
one of display on mst hub in unplugged or disabled, hdcp are
disabled for all displays on mst hub within hdcp_reset_display
by looping all displays of mst link. for displays still active,
their encryption status are off. kernel driver will not run hdcp
authentication again. therefore, hdcp are not enabled automatically.
[How]
within is_content_protection_different, check drm_crtc_state changes
of all displays on mst hub, if need, triger hdcp_update_display to
re-run hdcp authentication.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rename vram_scratch into mem_scratch and allow allocating it into GTT as
well.
The only problem with that is that we won't have a default page for the
system aperture any more.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1.Drop soft reset check when do should recover gpu check.
(As it will skip gpu reset operation if some ip is hang but
not support soft reset)
2.Check soft reset status before do soft reset when pre asic reset.
a. If check soft reset return true, it means: some ip is hang and
it also support soft reset, will try soft reset first.
b. If check soft reset return false, it means:
I. All the ip are not hang, will skip gpu reset.
II. Some ip is hang but not support soft reset, will skip soft
reset and retry with full reset later.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm-misc-next for 6.2:
Cross-subsystem Changes:
- fbdev: Make fb_modesetting_disabled() static
- udmabuf: Add vmap and vunmap methods to udmabuf_ops
Core Changes:
- doc: make drm-uapi igt-tests more readable
- fb-helper: Revert of the damage worker removal
- fourcc: Add missing big-endian XRGB1555 and RGB565 formats
- gem-shmem: Fix for resource leakage in __drm_gem_shmem_create()
- scheduler: Fix lockup in drm_sched_entity_kill()
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221124074615.ahflw5q5ktfdsr7k@houat
The pixel data for the ILI9486 is always 16-bits wide and it must be
sent over the SPI bus. When the controller is only able to deal with
8-bit transfers, this 16-bits data needs to be swapped before the
sending to account for the big endian bus, this is on the contrary not
needed when the SPI controller already supports 16-bits transfers.
The decision about swapping the pixel data or not is taken in the MIPI
DBI code by probing the controller capabilities: if the controller only
suppors 8-bit transfers the data is swapped, otherwise it is not.
This swapping/non-swapping is relying on the assumption that when the
controller does support 16-bit transactions then the data is sent
unswapped in 16-bits-per-word over SPI.
The problem with the ILI9486 driver is that it is forcing 8-bit
transactions also for controllers supporting 16-bits, violating the
assumption and corrupting the pixel data.
Align the driver to what is done in the MIPI DBI code by adjusting the
transfer size to the maximum allowed by the SPI controller.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh.gurudasani@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221116-s905x_spi_ili9486-v4-2-f86b4463b9e4@baylibre.com
Pull perf fixes from Borislav Petkov:
- Pass only an initialized perf event attribute to the LSM hook
- Fix a use-after-free on the perf syscall's error path
- A potential integer overflow fix in amd_core_pmu_init()
- Fix the cgroup events tracking after the context handling rewrite
- Return the proper value from the inherit_event() function on error
* tag 'perf_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Call LSM hook after copying perf_event_attr
perf: Fix use-after-free in error path
perf/x86/amd: fix potential integer overflow on shift of a int
perf/core: Fix cgroup events tracking
perf core: Return error pointer if inherit_event() fails to find pmu_ctx
Pull x86 fixes from Borislav Petkov:
- Two fixes to correct how kprobes handles INT3 now that they're added
by other functionality like the rethunks and not only kgdb
- Remove __init section markings of two functions which are referenced
by a function in the .text section
* tag 'x86_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kprobes: Fix optprobe optimization check with CONFIG_RETHUNK
x86/kprobes: Fix kprobes instruction boudary check with CONFIG_RETHUNK
x86/calldepth: Fix incorrect init section references
Pull locking fixes from Borislav Petkov:
- Prevent the leaking of a debug timer in futex_waitv()
- A preempt-RT mutex locking fix, adding the proper acquire semantics
* tag 'locking_urgent_for_v6.2_rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
futex: Fix futex_waitv() hrtimer debug object leak on kcalloc error
rtmutex: Add acquire semantics for rtmutex lock acquisition slow path
Pull drm fixes from Daniel Vetter:
"I'm just back from the mountains, and Dave is out at the beach and
should be back in a week again. Just i915 fixes and since Rodrigo
bothered to make the pull last week I figured I should warm up gpg and
forward this in a nice signed tag as a new years present!
- i915 fixes for newer platforms
- i915 locking rework to not give up in vm eviction fallback path too
early"
* tag 'drm-fixes-2023-01-01' of git://anongit.freedesktop.org/drm/drm:
drm/i915/dsi: fix MIPI_BKLT_EN_1 native GPIO index
drm/i915/dsi: add support for ICL+ native MIPI GPIO sequence
drm/i915/uc: Fix two issues with over-size firmware files
drm/i915: improve the catch-all evict to handle lock contention
drm/i915: Remove __maybe_unused from mtl_info
drm/i915: fix TLB invalidation for Gen12.50 video and compute engines
