The "mediatek,mt8183-mali" compatible uses platform data that calls for
getting (and managing) two regulators ("mali" and "sram") but devfreq
does not support this usecase, resulting in DVFS not working.
Since a lot of MediaTek SoCs need to set the voltages for the GPU SRAM
regulator in a specific relation to the GPU VCORE regulator, a MediaTek
SoC specific driver was introduced to automatically satisfy, through
coupling, these constraints: this means that there is at all no need to
manage both regulators in panfrost but to otherwise just manage the main
"mali" (-> gpu vcore) regulator instead.
Keeping in mind that we cannot break the ABI, the most sensible route
(avoiding hacks and uselessly overcomplicated code) to get a MT8183
node with one power supply was to add a new "mediatek,mt8183b-mali"
compatible, which effectively deprecates the former.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316102041.210269-12-angelogioacchino.delregno@collabora.com
MTL uses GSC command streamer i.e gsc cs to send HDCP/PXP commands
to GSC f/w. It requires to keep hdcp display driver
agnostic to content protection f/w (ME/GSC fw) in the form of
i915_hdcp_fw_ops generic ops.
Adding HDCP GSC CS interface by leveraging the i915_hdcp_fw_ops generic
ops instead of I915_HDCP_COMPONENT as integral part of i915.
Adding checks to see if GSC is loaded and proxy is setup
--v6
-dont change the license date in same patch series [Jani]
-fix the license year {Jani]
--v8
-remove stale comment [Ankit]
-get headers in alphabetical order [Ankit]
-fix hdcp2_supported check [Ankit]
--v9
-remove return statement from hdcp_gsc_fini [Ankit]
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316092927.668980-7-suraj.kandpal@intel.com
Add function that takes care of sending command to gsc cs. We start
of with allocation of memory for our command intel_hdcp_gsc_message that
contains gsc cs memory header as directed in specs followed by the
actual payload hdcp message that we want to send.
Spec states that we need to poll pending bit of response header around
20 times each try being 50ms apart hence adding that to current
gsc_msg_send function
Also we use the same function to take care of both sending and receiving
hence no separate function to get the response.
--v4
-Create common function to fill in gsc_mtl_header [Alan]
-define host session bitmask [Alan]
--v5
-use i915 directly instead of gt->i915 [Alan]
-No need to make fields NULL as we are already
using kzalloc [Alan]
--v8
-change mechanism to reuse the same memory for one hdcp session[Alan]
-fix header ordering
-add comments to explain flags and host session mask [Alan]
--v9
-remove gem obj from hdcp message as we can use
i915_vma_unpin_and_release [Alan]
-move hdcp message allocation and deallocation from hdcp2_enable and
hdcp2_disable to init and teardown of HDCP [Alan]
--v10
-remove unnecessary i915_vma_unpin [Alan]
--v11
-fix comment style [Uma]
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Alan Pervin Teres <alan.previn.teres.alexis@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316092927.668980-6-suraj.kandpal@intel.com
pre MTL we interact with mei interface to talk to
firmware and enable CP but going forward we will talk to gsc cs
because of which we are making all names for HDCP helpers and
structures generic as either mei or gsc cs maybe used.
Change the include/drm/i915_mei_hdcp_interface.h to
include/drm/i915_hdcp_interface.h
Change the i915_hdcp_interface.h header naming convention to
suit generic f/w type.
%s/MEI_/HDCP_
%s/mei_dev/hdcp_dev
Change structure name Accordingly.
%s/i915_hdcp_comp_master/i915_hdcp_master
%s/i915_hdcp_component_ops/i915_hdcp_ops
--v6
-make each patch build individually [Jani]
--v8
-change ME FW to ME/GSC FW [Ankit]
-fix formatting issue [Ankit]
--v9
-fix commit message and header [Uma]
--v10
-rename comp variable [Uma]
Cc: Tomas Winkler <tomas.winkler@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316092927.668980-3-suraj.kandpal@intel.com
This fixes a use-after-free crash during rmmod.
The DRM encoder is embedded inside the larger rockchip_hdmi,
which is allocated with the component. The component memory
gets freed before the main drm device is destroyed. Fix it
by running encoder cleanup before tearing down its container.
Signed-off-by: Toby Chen <tobyc@nvidia.com>
[moved encoder cleanup above clk_disable, similar to bind-error-path]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230317005126.496-1-tobyc@nvidia.com
clang reportes this error
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c:2322:8: error:
variable 'possible_crtcs' is used uninitialized whenever 'if'
condition is false [-Werror,-Wsometimes-uninitialized]
if (vp) {
^~
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c:2336:36: note:
uninitialized use occurs here
ret = vop2_plane_init(vop2, win, possible_crtcs);
^~~~~~~~~~~~~~
drivers/gpu/drm/rockchip/rockchip_drm_vop2.c:2322:4:
note: remove the 'if' if its condition is always true
if (vp) {
^~~~~~~~
The else-statement changes the win->type to OVERLAY without setting the
possible_crtcs variable. Rework the block, initialize possible_crtcs to
0 to remove the else-statement. Split the else-if-statement out to its
own if-statement so the OVERLAY check will catch when the win-type has
been changed.
Fixes: 368419a2d4 ("drm/rockchip: vop2: initialize possible_crtcs properly")
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316132302.531724-1-trix@redhat.com
The current way to determine during HW state sanitization if a PHY is
connected in the expected way doesn't work in all cases. The check for
this considers only the PHY ready/owned state and the initial TC mode
which was determined earlier by the TC port HW readout - using the
sink's HPD and the same PHY ready/owned states.
For instance for an enabled DP-alt/TBT port without the PHY ready/owned
flags set the initial mode will be TBT, and this will be regarded as a
valid PHY state. However it's possible that the port is actually enabled
in DP-alt mode, but for some reason the PHY ownership was not acquired.
Make sure the driver can detect invalid PHY states as in the above
example by checking the PHY ready/owned state wrt. the PLL type used.
This should be the TBT PLL if the PHY is not owned and the MG (non-TBT)
PLL if the PHY is owned.
v2: Rebased on change passing crtc_state in the previous patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-3-imre.deak@intel.com
For clarity factor out the function to determine if there are active
links on a TC port. This prepares for the next patch also checking the
port's PLL type.
While at it pass crtc_state to intel_tc_port_sanitize_mode(), and check
hw.active in that, instead of the deprecated crtc->active flag.
v2: Check crtc_state->hw.active instead of crtc->active. (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-2-imre.deak@intel.com
Since an HDMI output can only be enabled in legacy mode on TC ports,
assume that VBT is wrong and the port is legacy if VBT says the port is
non-legacy and has HDMI. If VBT says to enable DP as well leave the
non-legacy flag enabled, relying on the flag getting fixed up based on
the HPD status during sink detection.
v2: Fix the legacy port flag only if DP is not enabled.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230321220101.983366-1-imre.deak@intel.com
Atm, a TC port's initial mode will be read out as TBT mode in any case
the PHY ownership is not held. This isn't correct for legacy ports which
should be used only in legacy mode.
Fix the above initial mode to be disconnected mode for a legacy port and
TBT mode for DP-alt/TBT ports. Determine the port type by checking first
the HPD state and then the legacy VBT flag (so the HPD state can correct
a bogus VBT flag). If a sink is connected on a disabled port the PHY
will get also connected (switching it to legacy mode on a legacy port).
Also connect the PHY on a legacy port if it's enabled but BIOS
incorrectly left it in the disconnected state for some reason.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-10-imre.deak@intel.com
Atm, the target TC mode - which the PHY should be switched to at any
point it's used - is TBT in case there is no sink connected. However
legacy ports are only used in the legacy mode regardless of the sink
connected state. Fix the mode returned by
intel_tc_port_get_target_mode() accordingly.
Despite of the above issue, the PHY got disconnected as expected in
response to a sink disconnect event, causing only a redundant
PHY disconnect->reconnect sequence whenever the port was used.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-8-imre.deak@intel.com
During boot-up/system resume, the TC PHY on legacy ports will be
initialized by the IOM/TCSS firmware regardless of a sink being
connected or not (as opposed to DP-alt/TBT ports, which the FW only
inits once a sink is connected).
Wait for the above initialization to complete during HW readout, so that
connecting the PHY later will already see the expected PHY ready state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-6-imre.deak@intel.com
At least restoring the MST topology during system resume needs to use
AUX before the display HW readout->sanitization sequence is complete,
but on TC ports the PHY may be in the wrong mode for this, resulting in
the AUX transfers to fail.
The initial TC port mode is kept fixed as BIOS left it for the above HW
readout sequence (to prevent changing the mode on an enabled port). If
the port is disabled this initial mode is TBT - as in any case the PHY
ownership is not held - even if a DP-alt sink is connected. Thus, the
AUX transfers during this time will use TBT mode instead of the expected
DP-alt mode and so time out.
Fix the above by connecting the PHY during port initialization if the
port is disabled, which will switch to the expected mode (DP-alt in the
above case).
As the encoder/pipe HW state isn't read-out yet at this point, check if
the port is enabled based on the DDI_BUF enabled flag. Save the read-out
initial mode, so intel_tc_port_sanitize_mode() can check this wrt. the
read-out encoder HW state.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-5-imre.deak@intel.com
On TC ports the 4ms AUX timeout combined with the 5 * 32 retry
attempts during DPCD accesses adds a 640ms delay to each access if the
sink is disconnected. This in turn slows down a modeset during which the
sink is disconnected (for instance a disabling modeset).
Prevent the above delay by aborting AUX transfers on a TC port with a
disconnected sink.
The DP 1.4a link CTS (4.2.1.5 Source Device Inactive HPD / Inactive AUX
Test") also requires not to initiate AUX transfers on disconnected DP
ports in general, however this patch doesn't change the behavior on
non-TC ports, leaving that for a follow-up.
Reported-and-tested-by: Chris Chiu <chris.chiu@canonical.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8279
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230316131724.359612-2-imre.deak@intel.com
Consolidate all handling of CONFIG_DRM_FBDEV_LEAK_PHYS_SMEM by
making the module parameter optional in drm_fb_helper.c.
Without the config option, modules can set smem_start in struct
fb_info for internal usage, but not export if to userspace. The
address can only be exported by enabling the option and setting
the module parameter. Also update the comment.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng<suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-8-tzimmermann@suse.de
Remove all codepaths that implement fbdev output directly on GEM
buffers. Always allocate a shadow buffer in system memory and set
up deferred I/O for mmap.
The fbdev code that operated directly on GEM buffers was used by
drivers based on GEM DMA helpers. Those drivers have been migrated
to use fbdev-dma, a dedicated fbdev emulation for DMA memory. All
remaining users of fbdev-generic require shadow buffering.
Memory management of the remaining callers uses TTM, GEM SHMEM
helpers or a variant of GEM DMA helpers that is incompatible with
fbdev-dma. Therefore remove the unused codepaths from fbdev-generic
and simplify the code.
Using a shadow buffer with deferred I/O is probably the best case
for most remaining callers. Some of the TTM-based drivers might
benefit from a dedicated fbdev emulation that operates directly on
the driver's video memory.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Zack Rusin <zackr@vmware.com>
Tested-by: Sui Jingfeng <suijingfeng@loongson.cn>
Link: https://patchwork.freedesktop.org/patch/msgid/20230320150751.20399-2-tzimmermann@suse.de
