This is a revert of commit fd5894fa24 ("drm/vc4: hdmi: Remove clock
rate initialization"), with the code slightly moved around.
It turns out that we can't downright remove that code from the driver,
since the Pi0-3 and Pi4 are in different cases, and it only works for
the Pi4.
Indeed, the commit mentioned above was relying on the RaspberryPi
firmware clocks driver to initialize the rate if it wasn't done by the
firmware. However, the Pi0-3 are using the clk-bcm2835 clock driver that
wasn't doing this initialization. We therefore end up with the clock not
being assigned a rate, and the CPU stalling when trying to access a
register.
We can't move that initialization in the clk-bcm2835 driver, since the
HSM clock we depend on is actually part of the HDMI power domain, so any
rate setup is only valid when the power domain is enabled. Thus, we
reinstated the minimum rate setup at runtime_suspend, which should
address both issues.
Link: https://lore.kernel.org/dri-devel/20220922145448.w3xfywkn5ecak2et@pengutronix.de/
Fixes: fd5894fa24 ("drm/vc4: hdmi: Remove clock rate initialization")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929-rpi-pi3-unplugged-fixes-v1-1-cd22e962296c@cerno.tech
The VC4 HDMI controller driver relies on the HDMI codec ASoC driver. In
order to set it up properly, in vc4_hdmi_audio_init(), our HDMI driver
will register a device matching the HDMI codec driver, and then register
an ASoC card using that codec.
However, if vc4 is compiled as a module, chances are that the hdmi-codec
driver will be too. In such a case, the module loader will have a very
narrow window to load the module between the device registration and the
card registration.
If it fails to load the module in time, the card registration will fail
with EPROBE_DEFER, and we'll abort the audio initialisation,
unregistering the HDMI codec device in the process.
The next time the bind callback will be run, it's likely that we end up
missing that window again, effectively preventing vc4 to probe entirely.
In order to prevent this, we can create a soft dependency of the vc4
driver on the HDMI codec one so that we're sure the HDMI codec will be
loaded before the VC4 module is, and thus we'll never end up in the
previous situation.
Fixes: 91e99e1139 ("drm/vc4: hdmi: Register HDMI codec")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902144111.3424560-1-maxime@cerno.tech
This reverts commit 211f276ed3.
For quite some time, core DRM helpers already ensure that any relevant
connectors/CRTCs/etc. are disabled, as well as their associated
components (e.g., bridges) when suspending the system. Thus,
analogix_dp_bridge_{enable,disable}() already get called, which in turn
call drm_panel_{prepare,unprepare}(). This makes these drm_panel_*()
calls redundant.
Besides redundancy, there are a few problems with this handling:
(1) drm_panel_{prepare,unprepare}() are *not* reference-counted APIs and
are not in general designed to be handled by multiple callers --
although some panel drivers have a coarse 'prepared' flag that mitigates
some damage, at least. So at a minimum this is redundant and confusing,
but in some cases, this could be actively harmful.
(2) The error-handling is a bit non-standard. We ignored errors in
suspend(), but handled errors in resume(). And recently, people noticed
that the clk handling is unbalanced in error paths, and getting *that*
right is not actually trivial, given the current way errors are mostly
ignored.
(3) In the particular way analogix_dp_{suspend,resume}() get used (e.g.,
in rockchip_dp_*(), as a late/early callback), we don't necessarily have
a proper PM relationship between the DP/bridge device and the panel
device. So while the DP bridge gets resumed, the panel's parent device
(e.g., platform_device) may still be suspended, and so any prepare()
calls may fail.
So remove the superfluous, possibly-harmful suspend()/resume() handling
of panel state.
Fixes: 211f276ed3 ("drm: bridge: analogix/dp: add panel prepare/unprepare in suspend/resume time")
Link: https://lore.kernel.org/all/Yv2CPBD3Picg%2FgVe@google.com/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220822180729.1.I8ac5abe3a4c1c6fd5c061686c6e883c22f69022c@changeid
Fix gnome-shell (and other page-flip users) hanging after suspend/resume
because of the gma500's IRQs not working.
This fixes 2 problems with the IRQ handling:
1. gma_power_off() calls gma_irq_uninstall() which does a free_irq(), but
gma_power_on() called gma_irq_preinstall() + gma_irq_postinstall() which
do not call request_irq. Replace the pre- + post-install calls with
gma_irq_install() which does prep + request + post.
2. After fixing 1. IRQs still do not work on a Packard Bell Dot SC (Intel
Atom N2600, cedarview) netbook.
Cederview uses MSI interrupts and it seems that the BIOS re-configures
things back to normal APIC based interrupts during S3 suspend. There is
some MSI PCI-config registers save/restore code which tries to deal with
this, but on the Packard Bell Dot SC this is not sufficient to restore
MSI IRQ functionality after a suspend/resume.
Replace the PCI-config registers save/restore with pci_disable_msi() on
suspend + pci_enable_msi() on resume. Fixing e.g. gnome-shell hanging.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220906203852.527663-4-hdegoede@redhat.com
VPP_WRAP_OSD1_MATRIX_COEF22.Coeff22 is documented as being bits 0-12,
not 16-28.
Without this the output tends to have a pink hue, changing it results
in better color accuracy.
The vendor kernel doesn't use this register. However the code which
sets VIU2_OSD1_MATRIX_COEF22 also uses bits 0-12. There is a slightly
different style of registers for configuring some of the other matrices,
which do use bits 16-28 for this coefficient, but those have names
ending in MATRIX_COEF22_30, and this is not one of those.
Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com>
Fixes: 728883948b ("drm/meson: Add G12A Support for VIU setup")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908155243.687143-1-stuart.menefy@mathembedded.com
Commit 52824ca450 ("drm/panel-edp: Better describe eDP panel delays")
clarified the various delays used for eDP panels, tying them to the eDP
panel timing diagram.
For Innolux N116BCA-EA1, .prepare_to_enable would be:
t4_min + t5_min + t6_min + max(t7_max, t8_min)
Since t4_min and t5_min are both 0, the panel can use either .enable or
.prepare_to_enable.
As .enable is better defined, switch to using .enable for this panel.
Also add .disable = 50, based on the datasheet's t9_min value. This
effectively makes the delays the same as delay_200_500_e80_d50.
Cc: Douglas Anderson <dianders@chromium.org>
Fixes: 51d35631c9 ("drm/panel-simple: Add N116BCA-EA1")
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908085454.1024167-1-wenst@chromium.org
Enabling panfrost GPU OPP with dynamic regulator will make OPP
responsible to enable and configure it.
Unfortunately OPP configure and enable the regulator when an OPP
is asked to be set, which is not the case during
panfrost_devfreq_init().
This leave the regulator unconfigured and if no GPU load is
triggered, no OPP is asked to be set which make the regulator framework
switching it off during regulator_late_cleanup() without
noticing and therefore make the board hang as any access to GPU
memory space make bus locks up.
Call dev_pm_opp_set_opp() with the recommend OPP in
panfrost_devfreq_init() to enable the regulator, this will properly
configure and enable the regulator and will avoid any switch off
by regulator_late_cleanup().
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220906153034.153321-5-peron.clem@gmail.com
[Why]
Ghost BO is released with non-empty bulk move object. There is a
warning trace:
WARNING: CPU: 19 PID: 1582 at ttm/ttm_bo.c:366 ttm_bo_release+0x2e1/0x2f0 [amdttm]
Call Trace:
amddma_resv_reserve_fences+0x10d/0x1f0 [amdkcl]
amdttm_bo_put+0x28/0x30 [amdttm]
amdttm_bo_move_accel_cleanup+0x126/0x200 [amdttm]
amdgpu_bo_move+0x1a8/0x770 [amdgpu]
ttm_bo_handle_move_mem+0xb0/0x140 [amdttm]
amdttm_bo_validate+0xbf/0x100 [amdttm]
[How]
The resource of ghost BO should be moved to LRU directly, instead of
using bulk move. The bulk move object of ghost BO should set to NULL
before function ttm_bo_move_to_lru_tail_unlocked.
v2: set bulk move to NULL manually if no resource associated with ghost BO
Fixed: 5b951e487fd6bf5f ("drm/ttm: fix bulk move handling v2")
Signed-off-by: ZhenGuo Yin <zhenguo.yin@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220906084619.2545456-1-zhenguo.yin@amd.com
Previously when we added a fence to a dma_resv object we always
assumed the the newer than all the existing fences.
With Jason's work to add an UAPI to explicit export/import that's not
necessary the case any more. So without this check we would allow
userspace to force the kernel into an use after free error.
Since the change is very small and defensive it's probably a good
idea to backport this to stable kernels as well just in case others
are using the dma_resv object in the same way.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Jason Ekstrand <jason.ekstrand@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220810172617.140047-1-christian.koenig@amd.com
Cc: stable@vger.kernel.org # v5.19+
The current code tries to handle the case where CONFIG_PM isn't selected
by first calling our runtime_resume implementation and then properly
report the power state to the runtime_pm core.
This allows to have a functionning device even if pm_runtime_get_*
functions are nops.
However, the device power state if CONFIG_PM is enabled is
RPM_SUSPENDED, and thus our vc4_hdmi_write() and vc4_hdmi_read() calls
in the runtime_pm hooks will now report a warning since the device might
not be properly powered.
Even more so, we need CONFIG_PM enabled since the previous RaspberryPi
have a power domain that needs to be powered up for the HDMI controller
to be usable.
The previous patch has created a dependency on CONFIG_PM, now we can
just assume it's there and only call pm_runtime_resume_and_get() to make
sure our device is powered in bind.
Link: https://lore.kernel.org/r/20220629123510.1915022-39-maxime@cerno.tech
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
(cherry picked from commit 53565c28e6)
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Currently, the packet overhead is subtracted using unsigned arithmetic.
With a short sync pulse, this could underflow and wrap around to near
the maximal u16 value. Fix this by using signed subtraction. The call to
max() will correctly handle any negative numbers that are produced.
Apply the same fix to the other timings, even though those subtractions
are less likely to underflow.
Fixes: 133add5b5a ("drm/sun4i: Add Allwinner A31 MIPI-DSI controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220812031623.34057-1-samuel@sholland.org
Radix tree header includes gfp.h for __GFP_BITS_SHIFT only. Now we
have gfp_types.h for this.
Fixes powerpc allmodconfig build:
In file included from include/linux/nodemask.h:97,
from include/linux/mmzone.h:17,
from include/linux/gfp.h:7,
from include/linux/radix-tree.h:12,
from include/linux/idr.h:15,
from include/linux/kernfs.h:12,
from include/linux/sysfs.h:16,
from include/linux/kobject.h:20,
from include/linux/pci.h:35,
from arch/powerpc/kernel/prom_init.c:24:
include/linux/random.h: In function 'add_latent_entropy':
>> include/linux/random.h:25:46: error: 'latent_entropy' undeclared (first use in this function); did you mean 'add_latent_entropy'?
25 | add_device_randomness((const void *)&latent_entropy, sizeof(latent_entropy));
| ^~~~~~~~~~~~~~
| add_latent_entropy
include/linux/random.h:25:46: note: each undeclared identifier is reported only once for each function it appears in
Reported-by: kernel test robot <lkp@intel.com>
CC: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs lseek fix from Al Viro:
"Fix proc_reg_llseek() breakage. Always had been possible if somebody
left NULL ->proc_lseek, became a practical issue now"
* tag 'pull-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
take care to handle NULL ->proc_lseek()
Easily done now, just by clearing FMODE_LSEEK in ->f_mode
during proc_reg_open() for such entries.
Fixes: 868941b144 "fs: remove no_llseek"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull more xen updates from Juergen Gross:
- fix the handling of the "persistent grants" feature negotiation
between Xen blkfront and Xen blkback drivers
- a cleanup of xen.config and adding xen.config to Xen section in
MAINTAINERS
- support HVMOP_set_evtchn_upcall_vector, which is more compliant to
"normal" interrupt handling than the global callback used up to now
- further small cleanups
* tag 'for-linus-6.0-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: add xen config fragments to XEN HYPERVISOR sections
xen: remove XEN_SCRUB_PAGES in xen.config
xen/pciback: Fix comment typo
xen/xenbus: fix return type in xenbus_file_read()
xen-blkfront: Apply 'feature_persistent' parameter when connect
xen-blkback: Apply 'feature_persistent' parameter when connect
xen-blkback: fix persistent grants negotiation
x86/xen: Add support for HVMOP_set_evtchn_upcall_vector
Pull more perf tool updates from Arnaldo Carvalho de Melo:
- 'perf c2c' now supports ARM64, adjust its output to cope with
differences with what is in x86_64. Now go find false sharing on
ARM64 (at least Neoverse) as well!
- Refactor the JSON processing, making the output more compact and thus
reducing the size of the resulting perf binary
- Improvements for 'perf offcpu' profiling, including tracking child
processes
- Update Intel JSON metrics and events files for broadwellde,
broadwellx, cascadelakex, haswellx, icelakex, ivytown, jaketown,
knightslanding, sapphirerapids, skylakex and snowridgex
- Add 'perf stat' JSON output and a 'perf test' entry for it
- Ignore memfd and anonymous mmap events if jitdump present
- Refactor 'perf test' shell tests allowing subdirs
- Fix an error handling path in 'parse_perf_probe_command()'
- Fixes for the guest Intel PT tracing patchkit in the 1st batch of
this merge window
- Print debuginfod queries if -v option is used, to explain delays in
processing when debuginfo servers are enabled to fetch DSOs with
richer symbol tables
- Improve error message for 'perf record -p not_existing_pid'
- Fix openssl and libbpf feature detection
- Add PMU pai_crypto event description for IBM z16 on 'perf list'
- Fix typos and duplicated words on comments in various places
* tag 'perf-tools-fixes-for-v6.0-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (81 commits)
perf test: Refactor shell tests allowing subdirs
perf vendor events: Update events for snowridgex
perf vendor events: Update events and metrics for skylakex
perf vendor events: Update metrics for sapphirerapids
perf vendor events: Update events for knightslanding
perf vendor events: Update metrics for jaketown
perf vendor events: Update metrics for ivytown
perf vendor events: Update events and metrics for icelakex
perf vendor events: Update events and metrics for haswellx
perf vendor events: Update events and metrics for cascadelakex
perf vendor events: Update events and metrics for broadwellx
perf vendor events: Update metrics for broadwellde
perf jevents: Fold strings optimization
perf jevents: Compress the pmu_events_table
perf metrics: Copy entire pmu_event in find metric
perf pmu-events: Hide the pmu_events
perf pmu-events: Don't assume pmu_event is an array
perf pmu-events: Move test events/metrics to JSON
perf test: Use full metric resolution
perf pmu-events: Hide pmu_events_map
...
Pull powerpc fixes from Michael Ellerman:
- Ensure we never emit lwarx with EH=1 on 32-bit, because some 32-bit
CPUs trap on it rather than ignoring it as they should.
- Fix ftrace when building with clang, which was broken by some
refactoring.
- A couple of other minor fixes.
Thanks to Christophe Leroy, Naveen N. Rao, Nick Desaulniers, Ondrej
Mosnacek, Pali Rohár, Russell Currey, and Segher Boessenkool.
* tag 'powerpc-6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kexec: Fix build failure from uninitialised variable
powerpc/ppc-opcode: Fix PPC_RAW_TW()
powerpc64/ftrace: Fix ftrace for clang builds
powerpc: Make eh value more explicit when using lwarx
powerpc: Don't hide eh field of lwarx behind a macro
powerpc: Fix eh field when calling lwarx on PPC32
Pull /proc/mounts fix from Al Viro:
"Fix for /proc/mounts escaping - escape the '#' character too"
* tag 'pull-work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
vfs: escape hash as well
Pull more cifs updates from Steve French:
- two fixes for stable, one for a lock length miscalculation, and
another fixes a lease break timeout bug
- improvement to handle leases, allows the close timeout to be
configured more safely
- five restructuring/cleanup patches
* tag '5.20-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: Do not access tcon->cfids->cfid directly from is_path_accessible
cifs: Add constructor/destructors for tcon->cfid
SMB3: fix lease break timeout when multiple deferred close handles for the same file.
smb3: allow deferred close timeout to be configurable
cifs: Do not use tcon->cfid directly, use the cfid we get from open_cached_dir
cifs: Move cached-dir functions into a separate file
cifs: Remove {cifs,nfs}_fscache_release_page()
cifs: fix lock length calculation
Enable multipage folio support for the afs filesystem.
Support has already been implemented in netfslib, fscache and cachefiles
and in most of afs, but I've waited for Matthew Wilcox's latest folio
changes.
Note that it does require a change to afs_write_begin() to return the
correct subpage. This is a "temporary" change as we're working on
getting rid of the need for ->write_begin() and ->write_end()
completely, at least as far as network filesystems are concerned - but
it doesn't prevent afs from making use of the capability.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Tested-by: kafs-testing@auristor.com
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/lkml/2274528.1645833226@warthog.procyon.org.uk/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull timer fixes from Ingo Molnar:
"Misc timer fixes:
- fix a potential use-after-free bug in posix timers
- correct a prototype
- address a build warning"
* tag 'timers-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
posix-cpu-timers: Cleanup CPU timers before freeing them during exec
time: Correct the prototype of ns_to_kernel_old_timeval and ns_to_timespec64
posix-timers: Make do_clock_gettime() static
Pull x86 fix from Ingo Molnar:
"Fix the 'IBPB mitigated RETBleed' mode of operation on AMD CPUs (not
turned on by default), which also need STIBP enabled (if available) to
be '100% safe' on even the shortest speculation windows"
* tag 'x86-urgent-2022-08-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/bugs: Enable STIBP for IBPB mitigated RETBleed
Pull NTB updates from Jon Mason:
"Non-Transparent Bridge updates.
Fix of heap data and clang warnings, support for a new Intel NTB
device, and NTB EndPoint Function (EPF) support and the various fixes
for that"
* tag 'ntb-5.20' of https://github.com/jonmason/ntb:
MAINTAINERS: add PCI Endpoint NTB drivers to NTB files
NTB: EPF: Tidy up some bounds checks
NTB: EPF: Fix error code in epf_ntb_bind()
PCI: endpoint: pci-epf-vntb: reduce several globals to statics
PCI: endpoint: pci-epf-vntb: fix error handle in epf_ntb_mw_bar_init()
PCI: endpoint: Fix Kconfig dependency
NTB: EPF: set pointer addr to null using NULL rather than 0
Documentation: PCI: extend subheading underline for "lspci output" section
Documentation: PCI: Use code-block block for scratchpad registers diagram
Documentation: PCI: Add specification for the PCI vNTB function device
PCI: endpoint: Support NTB transfer between RC and EP
NTB: epf: Allow more flexibility in the memory BAR map method
PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address
ntb: intel: add GNR support for Intel PCIe gen5 NTB
NTB: ntb_tool: uninitialized heap data in tool_fn_write()
ntb: idt: fix clang -Wformat warnings
Pull more xfs updates from Darrick Wong:
"There's not a lot this time around, just the usual bug fixes and
corrections for missing error returns.
- Return error codes from block device flushes to userspace
- Fix a deadlock between reclaim and mount time quotacheck
- Fix an unnecessary ENOSPC return when doing COW on a filesystem
with severe free space fragmentation
- Fix a miscalculation in the transaction reservation computations
for file removal operations"
* tag 'xfs-5.20-merge-8' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: fix inode reservation space for removing transaction
xfs: Fix false ENOSPC when performing direct write on a delalloc extent in cow fork
xfs: fix intermittent hang during quotacheck
xfs: check return codes when flushing block devices
Pull more SCSI updates from James Bottomley:
"Mostly small bug fixes and trivial updates.
The major new core update is a change to the way device, target and
host reference counting is done to try to make it more robust (this
change has soaked for a while to try to winkle out any bugs)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: pm8001: Fix typo 'the the' in comment
scsi: megaraid_sas: Remove redundant variable cmd_type
scsi: FlashPoint: Remove redundant variable bm_int_st
scsi: zfcp: Fix missing auto port scan and thus missing target ports
scsi: core: Call blk_mq_free_tag_set() earlier
scsi: core: Simplify LLD module reference counting
scsi: core: Make sure that hosts outlive targets
scsi: core: Make sure that targets outlive devices
scsi: ufs: ufs-pci: Correct check for RESET DSM
scsi: target: core: De-RCU of se_lun and se_lun acl
scsi: target: core: Fix race during ACL removal
scsi: ufs: core: Correct ufshcd_shutdown() flow
scsi: ufs: core: Increase the maximum data buffer size
scsi: lpfc: Check the return value of alloc_workqueue()
Pull block fixes from Jens Axboe:
- NVMe pull request
- print nvme connect Linux error codes properly (Amit Engel)
- fix the fc_appid_store return value (Christoph Hellwig)
- fix a typo in an error message (Christophe JAILLET)
- add another non-unique identifier quirk (Dennis P. Kliem)
- check if the queue is allocated before stopping it in nvme-tcp
(Maurizio Lombardi)
- restart admin queue if the caller needs to restart queue in
nvme-fc (Ming Lei)
- use kmemdup instead of kmalloc + memcpy in nvme-auth (Zhang
Xiaoxu)
- __alloc_disk_node() error handling fix (Rafael)
* tag 'block-6.0-2022-08-12' of git://git.kernel.dk/linux-block:
block: Do not call blk_put_queue() if gendisk allocation fails
nvme-pci: add NVME_QUIRK_BOGUS_NID for ADATA XPG GAMMIX S70
nvme-tcp: check if the queue is allocated before stopping it
nvme-fabrics: Fix a typo in an error message
nvme-fabrics: parse nvme connect Linux error codes
nvmet-auth: use kmemdup instead of kmalloc + memcpy
nvme-fc: fix the fc_appid_store return value
nvme-fc: restart admin queue if the caller needs to restart queue
Pull io_uring fixes from Jens Axboe:
- Regression fix for this merge window, fixing a wrong order of
arguments for io_req_set_res() for passthru (Dylan)
- Fix for the audit code leaking context memory (Peilin)
- Ensure that provided buffers are memcg accounted (Pavel)
- Correctly handle short zero-copy sends (Pavel)
- Sparse warning fixes for the recvmsg multishot command (Dylan)
- Error handling fix for passthru (Anuj)
- Remove randomization of struct kiocb fields, to avoid it growing in
size if re-arranged in such a fashion that it grows more holes or
padding (Keith, Linus)
- Small series improving type safety of the sqe fields (Stefan)
* tag 'io_uring-6.0-2022-08-13' of git://git.kernel.dk/linux-block:
io_uring: add missing BUILD_BUG_ON() checks for new io_uring_sqe fields
io_uring: make io_kiocb_to_cmd() typesafe
fs: don't randomize struct kiocb fields
io_uring: consistently make use of io_notif_to_data()
io_uring: fix error handling for io_uring_cmd
io_uring: fix io_recvmsg_prep_multishot sparse warnings
io_uring/net: send retry for zerocopy
io_uring: mem-account pbuf buckets
audit, io_uring, io-wq: Fix memory leak in io_sq_thread() and io_wqe_worker()
io_uring: pass correct parameters to io_req_set_res
This is a prelude to adding more tests to shell tests and in order to
support putting those tests into subdirectories, I need to change the
test code that scans/finds and runs them.
To support subdirs I have to recurse so it's time to refactor the code
to allow this and centralize the shell script finding into one location
and only one single scan that builds a list of all the found tests in
memory instead of it being duplicated in 3 places.
This code also optimizes things like knowing the max width of desciption
strings (as we can do that while we scan instead of a whole new pass of
opening files).
It also more cleanly filters scripts to see only *.sh files thus
skipping random other files in directories like *~ backup files, other
random junk/data files that may appear and the scripts must be
executable to make the cut (this ensures the script lib dir is not seen
as scripts to run).
This avoids perf test running previous older versions of test scripts
that are editor backup files as well as skipping perf.data files that
may appear and so on.
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Tested-by: Leo Yan <leo.yan@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Cc: Suzuki Poulouse <suzuki.poulose@arm.com>
Cc: coresight@lists.linaro.org
Link: https://lore.kernel.org/r/20220812121641.336465-2-carsten.haitzler@foss.arm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
