Provide the 1.8 and 3.3 volt regulators that are utilised on the Debix
SOM BMB-08 base board.
Facilitate this by also supplying the pin control used to enable the
regulators on the second MIPI CSI port.
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Newer variants of Ixora boards require a power-up delay when powering up
the CAN transceiver of up to 1ms.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When the EEPROM is probed, we have this warning:
at24 0-0052: supply vcc not found, using dummy regulator
Add fixed 3.3v regulator to silence the warning.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Several schema warnings are seen when running:
make dtbs_check DT_SCHEMA_FILES=pci-bus.yaml
Fix them.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Even if the 'dsp' node is disabled the memory intended to be used by the
DSP is reserved. This limits the memory range suitable for CMA allocation.
Thus disable the dsp_reserved node. DSP users need to enable it in parallel
to the 'dsp' node.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The NPU is based on the Vivante GC8000 and its power-domain
is controlled my pgc_mlmix. Since the power-domain uses
some of these clocks, setup the clock parent and rates
inside the power-domain, and add the NPU node.
The data sheet states the CLK_ML_AHB should be 300MHz for
nominal, but 800MHz clock will divide down to 266 instead.
Boards which operate in over-drive mode should update the
clocks on their boards accordingly. When the driver loads,
the NPU numerates as:
etnaviv-gpu 38500000.npu: model: GC8000, revision: 8002
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds an overlay for the supported LVDS display AUO G133HAN01.
Configure the video PLL frequency to exactly match typical pixel clock of
141.200 MHz.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The anatop module produces PLL and OSC for Clock Controller Module. Since
the binding doc has been updated to clock-controller for this module,
Let's also update the device tree node.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To support SD3.0 mode, according to the SD spec, a clean power off
for the VDD_SD is keep the VDD_SD lower than 0.5V for at least 1ms.
On imx93 board, gate off the VDD_SD, it will cost about 10ms to see
the voltage change from 3.3v to 0.5v. So at least need to dealy 11ms
to make sure a clean power off and power on. Here add 12ms dealy.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For original setting, the start point is 20, after the SION setting,
ERR052021 can be workaround, but start point from 20 is too large,
especially for the LD 133MHz case.
Set the tuning start point as 1, tuning step as 2, so that, for the
40 times tuning logic, it can cover 1~81, its large and safe enough
for all different devices like eMMC/SD/SDIO.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx93 pad integrate has one issue, refer to ERR052021:
ERR052021 uSDHC: Sometimes uSDHC does not work under VDD_SOC low
drive mode and nominal mode
Description:
uSDHC PADs have one integration issue.
When CMD/DATA lines direction change from output to input, uSDHC
controller begin sampling, the integration issue will make input
enable signal from uSDHC propagated to the PAD with a long delay,
thus the new input value on the pad comes to uSDHC lately. The
uSDHC sampled the old input value and the sampling result is wrong.
Workaround:
Set uSDHC CMD/DATA PADs iomux register SION bit to 1, then PADs will
propagate input to uSDHC with no delay, so correct value is sampled.
This issue will wrongly trigger the start bit when sample the USDHC
command response, cause the USDHC trigger command CRC/index/endbit
error, which will finally impact the tuning pass window, espically
will impact the standard tuning logic, and can't find a correct delay
cell to get the best timing.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8MP DHCOM SoM production rev.200 is populated with M24C32-D
EEPROMs which have Additional Write lockable page at separate I2C
address. Describe the page in DT to make it available.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The baseboard of the Beacon i.MX8M Plus development kit has
an ADV7535 DSI to HDMI bridge capable of stereo sound.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for TQMa93xx module and MBa93xxCA starterkit mainboard.
TQMa93xx is a SOM using i.MX93 SOC. The SOM features PMIC, RAM, e-MMC and
some optional peripherals like SPI-NOR, RTC, EEPROM, gyroscope and
secure element.
TQMa93xxLA is a solder on type SOM and can be used on MBa93XXCA using an
adapter. TQMa93xxCA is a feature compatible, socketable type SOM.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configure clock rate for audio PLL. There's one audio PLL on i.MX93. It
is used as parent clock for clocks that are multiple of 8kHz.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull parisc architecture fixes from Helge Deller:
- Include the upper 5 address bits when inserting TLB entries on a
64-bit kernel.
On physical machines those are ignored, but in qemu it's nice to have
them included and to be correct.
- Stop the 64-bit kernel and show a warning if someone tries to boot on
a machine with a 32-bit CPU
- Fix a "no previous prototype" warning in parport-gsc
* tag 'parisc-for-6.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Prevent booting 64-bit kernels on PA1.x machines
parport: gsc: mark init function static
parisc/pgtable: Do not drop upper 5 address bits of physical address
Pull LoongArch updates from Huacai Chen:
- support PREEMPT_DYNAMIC with static keys
- relax memory ordering for atomic operations
- support BPF CPU v4 instructions for LoongArch
- some build and runtime warning fixes
* tag 'loongarch-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
selftests/bpf: Enable cpu v4 tests for LoongArch
LoongArch: BPF: Support signed mod instructions
LoongArch: BPF: Support signed div instructions
LoongArch: BPF: Support 32-bit offset jmp instructions
LoongArch: BPF: Support unconditional bswap instructions
LoongArch: BPF: Support sign-extension mov instructions
LoongArch: BPF: Support sign-extension load instructions
LoongArch: Add more instruction opcodes and emit_* helpers
LoongArch/smp: Call rcutree_report_cpu_starting() earlier
LoongArch: Relax memory ordering for atomic operations
LoongArch: Mark __percpu functions as always inline
LoongArch: Disable module from accessing external data directly
LoongArch: Support PREEMPT_DYNAMIC with static keys
Pull powerpc fixes from Michael Ellerman:
- Finish a refactor of pgprot_framebuffer() which dependend
on some changes that were merged via the drm tree
- Fix some kernel-doc warnings to quieten the bots
Thanks to Nathan Lynch and Thomas Zimmermann.
* tag 'powerpc-6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/rtas: Fix ppc_rtas_rmo_buf_show() kernel-doc
powerpc/pseries/rtas-work-area: Fix rtas_work_area_reserve_arena() kernel-doc
powerpc/fb: Call internal __phys_mem_access_prot() in fbdev code
powerpc: Remove file parameter from phys_mem_access_prot()
powerpc/machdep: Remove trailing whitespaces
Pull smb client fixes from Steve French:
- ctime caching fix (for setxattr)
- encryption fix
- DNS resolver mount fix
- debugging improvements
- multichannel fixes including cases where server stops or starts
supporting multichannel after mount
- reconnect fix
- minor cleanups
* tag '6.7-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number for cifs.ko
cifs: handle when server stops supporting multichannel
cifs: handle when server starts supporting multichannel
Missing field not being returned in ioctl CIFS_IOC_GET_MNT_INFO
smb3: allow dumping session and tcon id to improve stats analysis and debugging
smb: client: fix mount when dns_resolver key is not available
smb3: fix caching of ctime on setxattr
smb3: minor cleanup of session handling code
cifs: reconnect work should have reference on server struct
cifs: do not pass cifs_sb when trying to add channels
cifs: account for primary channel in the interface list
cifs: distribute channels across interfaces based on speed
cifs: handle cases where a channel is closed
smb3: more minor cleanups for session handling routines
smb3: minor RDMA cleanup
cifs: Fix encryption of cleared, but unset rq_iter data buffers
Pull probes fixes from Masami Hiramatsu:
- Documentation update: Add a note about argument and return value
fetching is the best effort because it depends on the type.
- objpool: Fix to make internal global variables static in
test_objpool.c.
- kprobes: Unify kprobes_exceptions_nofify() prototypes. There are the
same prototypes in asm/kprobes.h for some architectures, but some of
them are missing the prototype and it causes a warning. So move the
prototype into linux/kprobes.h.
- tracing: Fix to check the tracepoint event and return event at
parsing stage. The tracepoint event doesn't support %return but if
$retval exists, it will be converted to %return silently. This finds
that case and rejects it.
- tracing: Fix the order of the descriptions about the parameters of
__kprobe_event_gen_cmd_start() to be consistent with the argument
list of the function.
* tag 'probes-fixes-v6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/kprobes: Fix the order of argument descriptions
tracing: fprobe-event: Fix to check tracepoint event and return
kprobes: unify kprobes_exceptions_nofify() prototypes
lib: test_objpool: make global variables static
Documentation: tracing: Add a note about argument and retval access
Pull fbdev fixes and cleanups from Helge Deller:
- fix double free and resource leaks in imsttfb
- lots of remove callback cleanups and section mismatch fixes in
omapfb, amifb and atmel_lcdfb
- error code fix and memparse simplification in omapfb
* tag 'fbdev-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/linux-fbdev: (31 commits)
fbdev: fsl-diu-fb: mark wr_reg_wa() static
fbdev: amifb: Convert to platform remove callback returning void
fbdev: amifb: Mark driver struct with __refdata to prevent section mismatch warning
fbdev: hyperv_fb: fix uninitialized local variable use
fbdev: omapfb/tpd12s015: Convert to platform remove callback returning void
fbdev: omapfb/tfp410: Convert to platform remove callback returning void
fbdev: omapfb/sharp-ls037v7dw01: Convert to platform remove callback returning void
fbdev: omapfb/opa362: Convert to platform remove callback returning void
fbdev: omapfb/hdmi: Convert to platform remove callback returning void
fbdev: omapfb/dvi: Convert to platform remove callback returning void
fbdev: omapfb/dsi-cm: Convert to platform remove callback returning void
fbdev: omapfb/dpi: Convert to platform remove callback returning void
fbdev: omapfb/analog-tv: Convert to platform remove callback returning void
fbdev: atmel_lcdfb: Convert to platform remove callback returning void
fbdev: omapfb/tpd12s015: Don't put .remove() in .exit.text and drop suppress_bind_attrs
fbdev: omapfb/tfp410: Don't put .remove() in .exit.text and drop suppress_bind_attrs
fbdev: omapfb/sharp-ls037v7dw01: Don't put .remove() in .exit.text and drop suppress_bind_attrs
fbdev: omapfb/opa362: Don't put .remove() in .exit.text and drop suppress_bind_attrs
fbdev: omapfb/hdmi: Don't put .remove() in .exit.text and drop suppress_bind_attrs
fbdev: omapfb/dvi: Don't put .remove() in .exit.text and drop suppress_bind_attrs
...
Pull drm fixes from Daniel Vetter:
"Dave's VPN to the big machine died, so it's on me to do fixes pr this
and next week while everyone else is at plumbers.
- big pile of amd fixes, but mostly for hw support newly added in 6.7
- i915 fixes, mostly minor things
- qxl memory leak fix
- vc4 uaf fix in mock helpers
- syncobj fix for DRM_SYNCOBJ_WAIT_FLAGS_WAIT_AVAILABLE"
* tag 'drm-next-2023-11-10' of git://anongit.freedesktop.org/drm/drm: (78 commits)
drm/amdgpu: fix error handling in amdgpu_vm_init
drm/amdgpu: Fix possible null pointer dereference
drm/amdgpu: move UVD and VCE sched entity init after sched init
drm/amdgpu: move kfd_resume before the ip late init
drm/amd: Explicitly check for GFXOFF to be enabled for s0ix
drm/amdgpu: Change WREG32_RLC to WREG32_SOC15_RLC where inst != 0 (v2)
drm/amdgpu: Use correct KIQ MEC engine for gfx9.4.3 (v5)
drm/amdgpu: add smu v13.0.6 pcs xgmi ras error query support
drm/amdgpu: fix software pci_unplug on some chips
drm/amd/display: remove duplicated argument
drm/amdgpu: correct mca debugfs dump reg list
drm/amdgpu: correct acclerator check architecutre dump
drm/amdgpu: add pcs xgmi v6.4.0 ras support
drm/amdgpu: Change extended-scope MTYPE on GC 9.4.3
drm/amdgpu: disable smu v13.0.6 mca debug mode by default
drm/amdgpu: Support multiple error query modes
drm/amdgpu: refine smu v13.0.6 mca dump driver
drm/amdgpu: Do not program PF-only regs in hdp_v4_0.c under SRIOV (v2)
drm/amdgpu: Skip PCTL0_MMHUB_DEEPSLEEP_IB write in jpegv4.0.3 under SRIOV
drm: amd: Resolve Sphinx unexpected indentation warning
...
Pull arm64 fixes from Catalin Marinas:
"Mostly PMU fixes and a reworking of the pseudo-NMI disabling on broken
MediaTek firmware:
- Move the MediaTek GIC quirk handling from irqchip to core. Before
the merging window commit 44bd78dd2b ("irqchip/gic-v3: Disable
pseudo NMIs on MediaTek devices w/ firmware issues") temporarily
addressed this issue. Fixed now at a deeper level in the arch code
- Reject events meant for other PMUs in the CoreSight PMU driver,
otherwise some of the core PMU events would disappear
- Fix the Armv8 PMUv3 driver driver to not truncate 64-bit registers,
causing some events to be invisible
- Remove duplicate declaration of __arm64_sys##name following the
patch to avoid prototype warning for syscalls
- Typos in the elf_hwcap documentation"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/syscall: Remove duplicate declaration
Revert "arm64: smp: avoid NMI IPIs with broken MediaTek FW"
arm64: Move MediaTek GIC quirk handling from irqchip to core
arm64/arm: arm_pmuv3: perf: Don't truncate 64-bit registers
perf: arm_cspmu: Reject events meant for other PMUs
Documentation/arm64: Fix typos in elf_hwcaps
Pull sound fixes from Takashi Iwai:
"A collection of fixes for rc1.
The majority of changes are various ASoC driver-specific small fixes
and usual HD-audio quirks, while there are a couple of core changes: a
fix in ALSA core procfs code to avoid deadlocks at disconnection and
an ASoC core fix for DAPM clock widgets"
* tag 'sound-fix-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
OSS: dmasound/paula: Convert to platform remove callback returning void
ALSA: hda: ASUS UM5302LA: Added quirks for cs35L41/10431A83 on i2c bus
ALSA: info: Fix potential deadlock at disconnection
ASoC: nau8540: Add self recovery to improve capture quility
ALSA: hda/realtek: Add support dual speaker for Dell
ALSA: hda: Add ASRock X670E Taichi to denylist
ALSA: hda/realtek: Add quirk for ASUS UX7602ZM
ASoC: SOF: sof-client: trivial: fix comment typo
ASoC: dapm: fix clock get name
ASoC: hdmi-codec: register hpd callback on component probe
ASoC: mediatek: mt8186_mt6366_rt1019_rt5682s: trivial: fix error messages
ASoC: da7219: Improve system suspend and resume handling
ASoC: codecs: Modify macro value error
ASoC: codecs: Modify the wrong judgment of re value
ASoC: codecs: Modify the maximum value of calib
ASoC: amd: acp: fix for i2s mode register field update
ASoC: codecs: aw88399: Fix -Wuninitialized in aw_dev_set_vcalb()
ASoC: rt712-sdca: fix speaker route missing issue
ASoC: rockchip: Fix unused rockchip_i2s_tdm_match warning for !CONFIG_OF
ASoC: ti: omap-mcbsp: Fix runtime PM underflow warnings
Pull spi fixes from Mark Brown:
"A couple of fixes that came in during the merge window: one Kconfig
dependency fix and another fix for a long standing issue where a sync
transfer races with system suspend"
* tag 'spi-fix-v6.7-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: Fix null dereference on suspend
spi: spi-zynq-qspi: add spi-mem to driver kconfig dependencies
Pull MMC fixes from Ulf Hansson:
"MMC core:
- Fix broken cache-flush support for Micron eMMCs
- Revert 'mmc: core: Capture correct oemid-bits for eMMC cards'
MMC host:
- sdhci_am654: Fix TAP value parsing for legacy speed mode
- sdhci-pci-gli: Fix support for ASPM mode for GL9755/GL9750
- vub300: Fix an error path in probe"
* tag 'mmc-v6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-pci-gli: GL9750: Mask the replay timer timeout of AER
mmc: sdhci-pci-gli: GL9755: Mask the replay timer timeout of AER
Revert "mmc: core: Capture correct oemid-bits for eMMC cards"
mmc: vub300: fix an error code
mmc: Add quirk MMC_QUIRK_BROKEN_CACHE_FLUSH for Micron eMMC Q2J54A
mmc: sdhci_am654: fix start loop index for TAP value parsing
Pull pwm fixes from Thierry Reding:
"This contains two very small fixes that I failed to include in the
main pull request"
* tag 'pwm/for-6.7-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Fix double shift bug
pwm: samsung: Fix a bit test in pwm_samsung_resume()
Pull io_uring fixes from Jens Axboe:
"Mostly just a few fixes and cleanups caused by the read multishot
support.
Outside of that, a stable fix for how a connect retry is done"
* tag 'io_uring-6.7-2023-11-10' of git://git.kernel.dk/linux:
io_uring: do not clamp read length for multishot read
io_uring: do not allow multishot read to set addr or len
io_uring: indicate if io_kbuf_recycle did recycle anything
io_uring/rw: add separate prep handler for fixed read/write
io_uring/rw: add separate prep handler for readv/writev
io_uring/net: ensure socket is marked connected on connect retry
io_uring/rw: don't attempt to allocate async data if opcode doesn't need it
Pull block fixes from Jens Axboe:
- NVMe pull request via Keith:
- nvme keyring config compile fixes (Hannes and Arnd)
- fabrics keep alive fixes (Hannes)
- tcp authentication fixes (Mark)
- io_uring_cmd error handling fix (Anuj)
- stale firmware attribute fix (Daniel)
- tcp memory leak (Christophe)
- crypto library usage simplification (Eric)
- nbd use-after-free fix. May need a followup, but at least it's better
than what it was before (Li)
- Rate limit write on read-only device warnings (Yu)
* tag 'block-6.7-2023-11-10' of git://git.kernel.dk/linux:
nvme: keyring: fix conditional compilation
nvme: common: make keyring and auth separate modules
blk-core: use pr_warn_ratelimited() in bio_check_ro()
nbd: fix uaf in nbd_open
nvme: start keep-alive after admin queue setup
nvme-loop: always quiesce and cancel commands before destroying admin q
nvme-tcp: avoid open-coding nvme_tcp_teardown_admin_queue()
nvme-auth: always set valid seq_num in dhchap reply
nvme-auth: add flag for bi-directional auth
nvme-auth: auth success1 msg always includes resp
nvme: fix error-handling for io_uring nvme-passthrough
nvme: update firmware version after commit
nvme-tcp: Fix a memory leak
nvme-auth: use crypto_shash_tfm_digest()
Pull ata fixes from Damien Le Moal:
- Revert a change in ata_pci_shutdown_one() to suspend disks on
shutdown as this is now done using the manage_shutdown scsi device
flag (me)
- Change the pata_falcon and pata_gayle drivers to stop using
module_platform_driver_probe(). This makes these drivers more inline
with all other drivers (allowing bind/unbind) and suppress a
compilation warning (Uwe)
- Convert the pata_falcon and pata_gayle drivers to the new
.remove_new() void-return callback. These 2 drivers are the last ones
needing this change (Uwe)
* tag 'ata-6.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_gayle: Convert to platform remove callback returning void
ata: pata_falcon: Convert to platform remove callback returning void
ata: pata_gayle: Stop using module_platform_driver_probe()
ata: pata_falcon: Stop using module_platform_driver_probe()
ata: libata-core: Fix ata_pci_shutdown_one()
Pull dma-mapping fixes from Christoph Hellwig:
- don't leave pages decrypted for DMA in encrypted memory setups linger
around on failure (Petr Tesarik)
- fix an out of bounds access in the new dynamic swiotlb code (Petr
Tesarik)
- fix dma_addressing_limited for systems with weird physical memory
layouts (Jia He)
* tag 'dma-mapping-6.7-2023-11-10' of git://git.infradead.org/users/hch/dma-mapping:
swiotlb: fix out-of-bounds TLB allocations with CONFIG_SWIOTLB_DYNAMIC
dma-mapping: fix dma_addressing_limited() if dma_range_map can't cover all system RAM
dma-mapping: move dma_addressing_limited() out of line
swiotlb: do not free decrypted pages if dynamic
Pull lsm updates from Paul Moore:
"We've got two small patches to correct the default return
value of two LSM hooks: security_vm_enough_memory_mm() and
security_inode_getsecctx()"
* tag 'lsm-pr-20231109' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/lsm:
lsm: fix default return value for inode_getsecctx
lsm: fix default return value for vm_enough_memory
Pull smb server fixes from Steve French:
- slab out of bounds fix in ACL handling
- fix malformed request oops
- minor doc fix
* tag '6.7-rc-smb3-server-part2' of git://git.samba.org/ksmbd:
ksmbd: handle malformed smb1 message
ksmbd: fix kernel-doc comment of ksmbd_vfs_kern_path_locked()
ksmbd: fix slab out of bounds write in smb_inherit_dacl()
Pull ceph updates from Ilya Dryomov:
- support for idmapped mounts in CephFS (Christian Brauner, Alexander
Mikhalitsyn).
The series was originally developed by Christian and later picked up
and brought over the finish line by Alexander, who also contributed
an enabler on the MDS side (separate owner_{u,g}id fields on the
wire).
The required exports for mnt_idmap_{get,put}() in VFS have been acked
by Christian and received no objection from Christoph.
- a churny change in CephFS logging to include cluster and client
identifiers in log and debug messages (Xiubo Li).
This would help in scenarios with dozens of CephFS mounts on the same
node which are getting increasingly common, especially in the
Kubernetes world.
* tag 'ceph-for-6.7-rc1' of https://github.com/ceph/ceph-client:
ceph: allow idmapped mounts
ceph: allow idmapped atomic_open inode op
ceph: allow idmapped set_acl inode op
ceph: allow idmapped setattr inode op
ceph: pass idmap to __ceph_setattr
ceph: allow idmapped permission inode op
ceph: allow idmapped getattr inode op
ceph: pass an idmapping to mknod/symlink/mkdir
ceph: add enable_unsafe_idmap module parameter
ceph: handle idmapped mounts in create_request_message()
ceph: stash idmapping in mdsc request
fs: export mnt_idmap_get/mnt_idmap_put
libceph, ceph: move mdsmap.h to fs/ceph
ceph: print cluster fsid and client global_id in all debug logs
ceph: rename _to_client() to _to_fs_client()
ceph: pass the mdsc to several helpers
libceph: add doutc and *_client debug macros support
Pull more RISC-V updates from Palmer Dabbelt:
- Support for handling misaligned accesses in S-mode
- Probing for misaligned access support is now properly cached and
handled in parallel
- PTDUMP now reflects the SW reserved bits, as well as the PBMT and
NAPOT extensions
- Performance improvements for TLB flushing
- Support for many new relocations in the module loader
- Various bug fixes and cleanups
* tag 'riscv-for-linus-6.7-mw2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux: (51 commits)
riscv: Optimize bitops with Zbb extension
riscv: Rearrange hwcap.h and cpufeature.h
drivers: perf: Do not broadcast to other cpus when starting a counter
drivers: perf: Check find_first_bit() return value
of: property: Add fw_devlink support for msi-parent
RISC-V: Don't fail in riscv_of_parent_hartid() for disabled HARTs
riscv: Fix set_memory_XX() and set_direct_map_XX() by splitting huge linear mappings
riscv: Don't use PGD entries for the linear mapping
RISC-V: Probe misaligned access speed in parallel
RISC-V: Remove __init on unaligned_emulation_finish()
RISC-V: Show accurate per-hart isa in /proc/cpuinfo
RISC-V: Don't rely on positional structure initialization
riscv: Add tests for riscv module loading
riscv: Add remaining module relocations
riscv: Avoid unaligned access when relocating modules
riscv: split cache ops out of dma-noncoherent.c
riscv: Improve flush_tlb_kernel_range()
riscv: Make __flush_tlb_range() loop over pte instead of flushing the whole tlb
riscv: Improve flush_tlb_range() for hugetlb pages
riscv: Improve tlb_flush()
...
Pull MIPS updates from Thomas Bogendoerfer:
- removed AR7 platform support
- cleanups and fixes
* tag 'mips_6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: AR7: remove platform
watchdog: ar7_wdt: remove driver to prepare for platform removal
vlynq: remove bus driver
mtd: parsers: ar7: remove support
serial: 8250: remove AR7 support
arch: mips: remove ReiserFS from defconfig
MIPS: lantiq: Remove unnecessary include of <linux/of_irq.h>
MIPS: lantiq: Fix pcibios_plat_dev_init() "no previous prototype" warning
MIPS: KVM: Fix a build warning about variable set but not used
MIPS: Remove dead code in relocate_new_kernel
mips: dts: ralink: mt7621: rename to GnuBee GB-PC1 and GnuBee GB-PC2
mips: dts: ralink: mt7621: define each reset as an item
mips: dts: ingenic: Remove unneeded probe-type properties
MIPS: loongson32: Remove dma.h and nand.h
