Reorder the of_device_id structures so that they are in alphabetical
order.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Update the main TI TWL-family binding to be self-contained and to fix
pre-existing validation errors.
To ensure future patches are bisectable, child nodes whose bindings
are in other patches (audio, keypad, usb, etc.) are now defined using
a flexible 'additionalProperties: true' pattern. This removes hard
dependencies between the MFD and subsystem bindings.
The complete dtbs_check for this binding is clean except for two
warnings originating from pre-existing bugs in the OMAP DTS files,
for which fixes have already been submitted separately [1][2].
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <ukleinek@kernel.org>
Signed-off-by: Jihed Chaibi <jihed.chaibi.dev@gmail.com>
Reviewed-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee@kernel.org>
The SMARC-sAM67 board has an on-board uC which has the same register
interface as the older CPLD implementation on the SMARC-sAL28 board.
Although the MCU emulates the same behavior, be prepared for any quirks
and add a board specific compatible.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee@kernel.org>
Setting the signal names in the device tree was already possible, but
it will lead to a warning. Allow the gpio-line-names property to fix
that.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: "Rob Herring (Arm)" <robh@kernel.org>
Signed-off-by: Lee Jones <lee@kernel.org>
Current implementation describes only MFD's own topsys interrupts.
However, max77705 has a register which indicates interrupt source, i.e.
it acts as an interrupt controller. There's 4 interrupt sources in
max77705: topsys, charger, fuelgauge, usb type-c manager.
Setup max77705 MFD parent as an interrupt controller. Delete topsys
interrupts because currently unused.
Remove shared interrupt flag, because we're are an interrupt controller
now, and subdevices should request interrupts from us.
Fixes: c8d50f0297 ("mfd: Add new driver for MAX77705 PMIC")
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Link: https://lore.kernel.org/r/20250909-max77705-fix_interrupt_handling-v3-1-233c5a1a20b5@gmail.com
Signed-off-by: Lee Jones <lee@kernel.org>
As pm_runtime_force_suspend() will force the device state to suspend,
the driver needs to ensure no IRQ handlers are currently running. If not
those handlers may find they are now running on suspended hardware
despite holding a PM runtime reference. disable_irq() will sync any
currently running handlers, so move the IRQ disabling to cover the whole
of the forced suspend state to avoid such race conditions.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20250903094549.271068-6-ckeepax@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>
Since the display is a sub-function of the Loongson-2K BMC, when the
BMC reset, the entire BMC PCIe is disconnected, including the display
which is interrupted.
Quick overview of the entire LS2K BMC reset process:
There are two types of reset methods: soft reset (BMC-initiated reboot
of IPMI reset command) and BMC watchdog reset (watchdog timeout).
First, regardless of the method, an interrupt is generated (PCIe interrupt
for soft reset/GPIO interrupt for watchdog reset);
Second, during the interrupt process, the system enters bmc_reset_work,
clears the bus/IO/mem resources of the LS7A PCI-E bridge, waits for the BMC
reset to begin, then restores the parent device's PCI configuration space,
waits for the BMC reset to complete, and finally restores the BMC PCI
configuration space.
Display restoration occurs last.
Co-developed-by: Chong Qiao <qiaochong@loongson.cn>
Signed-off-by: Chong Qiao <qiaochong@loongson.cn>
Reviewed-by: Huacai Chen <chenhuacai@loongson.cn>
Acked-by: Corey Minyard <corey@minyard.net>
Signed-off-by: Binbin Zhou <zhoubinbin@loongson.cn>
Link: https://lore.kernel.org/r/de4e04b42ff9ee282f86f9bb9efbf959a9848205.1756987761.git.zhoubinbin@loongson.cn
Signed-off-by: Lee Jones <lee@kernel.org>
Convert the txt mc13xxx bindings to DT schema attempting to keep most
information. The nodes codec and touchscreen are not part of the new
schema since it was only briefly mentioned before.
Following the convention, rename led-control to fsl,led-control.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250829201517.15374-6-akurz@blala.de
Signed-off-by: Lee Jones <lee@kernel.org>
When an MFD device is added, a platform_device is allocated. If this
device is linked to a DT description, the corresponding OF node is linked
to the new platform device but the OF node's refcount isn't incremented.
As of_node_put() is called during the platform device release, it leads
to a refcount underflow.
Call of_node_get() to increment the OF node's refcount when the node is
linked to the newly created platform device.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Link: https://lore.kernel.org/r/20250820-mfd-refcount-v1-1-6dcb5eb41756@bootlin.com
Signed-off-by: Lee Jones <lee@kernel.org>
Enable support for the RTC and regulators found in the SpacemiT P1
PMIC. Support is implemented by the simple I2C MFD driver.
The P1 PMIC is normally implemented with the SpacemiT K1 SoC. This
PMIC provides 6 buck converters and 12 LDO regulators. It also
implements a switch, watchdog timer, real-time clock, and more.
Initially its RTC and regulators are supported.
Signed-off-by: Alex Elder <elder@riscstar.com>
Link: https://lore.kernel.org/r/20250825172057.163883-3-elder@riscstar.com
Signed-off-by: Lee Jones <lee@kernel.org>
This driver uses the legacy gpiolib interfaces to get gpio
numbers from platform data. There are no in-tree users of
this driver, so nothing defines the platform data.
Add a dependency on GPIOLIB_LEGACY for the moment to avoid the build
failure, and make sure the sound driver does not get built without the
mfd portion either pass that dependency along.
Alternatively, we could remove the mfd driver along with the backlight
and regulator portions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250808151822.536879-15-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
This driver uses the legacy gpiolib interfaces to get gpio
numbers from platform data:
drivers/mfd/si476x-i2c.c: In function 'si476x_core_start':
drivers/mfd/si476x-i2c.c:133:21: error: implicit declaration of function 'gpio_is_valid'; did you mean 'uuid_is_valid'? [-Werror=implicit-function-declaration]
133 | if (gpio_is_valid(core->gpio_reset))
There are no in-tree users of this driver, so nothing defines
the platform data.
Add a dependency on GPIOLIB_LEGACY for the moment to avoid the build
failure, and make sure the sound driver does not get built without the
mfd portion either pass that dependency along.
Alternatively, we could remove the mfd driver along with the radio and
sound portions.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202507231653.UFlH2dMO-lkp@intel.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250808151822.536879-14-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Move several embedded controller bindings (like ChromeOS EC, Gateworks
System Controller and Kontron sl28cpld Board Management) to new
subdirectory "embedded-controller" matching their purpose.
An embedded controller (EC) is a discrete component that contains a
microcontroller (i.e. a small CPU running a small firmware without
operating system) mounted into a larger computer system running
a fully fledged operating system that needs to utilize the embedded
controller as part of its operation.
So far the EC bindings were split between "mfd" and "platform"
directory. MFD name comes from Linux, not hardware, and "platform" is a
bit too generic.
Rename Gateworks GSC and Huawei Gaokun filenames to match compatible, as
preferred for bindings.
Acked-by: Michael Walle <mwalle@kernel.org> # for sl28cpld
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Link: https://lore.kernel.org/r/20250825081201.9775-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
The ASpeed lpc-snoop nodes have a "clocks" property which isn't
documented. It looks like all the LPC child devices have the same clock
source. Perhaps it is the parent device that should have the clock, but
it's too late for that. The driver for lpc-snoop requires a clock to be
present.
Signed-off-by: "Rob Herring (Arm)" <robh@kernel.org>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20250807132909.3291770-1-robh@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
clang-21 warns about one uninitialized variable getting dereferenced
in madera_dev_init:
drivers/mfd/madera-core.c:739:10: error: variable 'mfd_devs' is uninitialized when used here [-Werror,-Wuninitialized]
739 | mfd_devs, n_devs,
| ^~~~~~~~
drivers/mfd/madera-core.c:459:33: note: initialize the variable 'mfd_devs' to silence this warning
459 | const struct mfd_cell *mfd_devs;
| ^
| = NULL
The code is actually correct here because n_devs is only nonzero
when mfd_devs is a valid pointer, but this is impossible for the
compiler to see reliably.
Change the logic to check for the pointer as well, to make this easier
for the compiler to follow.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20250807071932.4085458-1-arnd@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
When `devm_add_action_or_reset()` fails, it is due to a failed memory
allocation and will thus return `-ENOMEM`. `dev_err_probe()` doesn't do
anything when error is `-ENOMEM`. Therefore, remove the useless call to
`dev_err_probe()` when `devm_add_action_or_reset()` fails, and just
return the value instead.
Signed-off-by: Waqar Hameed <waqar.hameed@axis.com>
Reviewed-by: Sven Peter <sven@kernel.org>
Link: https://lore.kernel.org/r/pnd8qjym7td.a.out@axis.com
Signed-off-by: Lee Jones <lee@kernel.org>
We observed the initial probe of the da9063 failing in
da9063_get_device_type in about 30% of boots on a Xilinx ZynqMP based
board. The problem originates in da9063_i2c_blockreg_read, which uses
a single bus transaction to turn the register page and then read a
register. On the bus, this should translate to a write to register 0,
followed by a read to the target register, separated by a repeated
start. However, we found that after the write to register 0, the
controller sometimes continues directly with the register address of
the read request, without sending the chip address or a repeated start
in between, which makes the read request invalid.
To fix this, separate turning the page and reading the register into
two separate transactions. This brings the initialization code in line
with the rest of the driver, which uses register maps (which to my
knowledge do not use repeated starts after turning the page). This has
been included in our kernel for several months and was recently
included in a shipped product. For us, it reliably fixes the issue,
and we have not observed any new issues.
While the underlying problem is probably with the i2c controller or
its driver, I still propose a change here in the interest of
robustness: First, I'm not sure this issue can be fixed on the
controller side, since there are other issues related to repeated
start which can't (AR# 60695, AR# 61664). Second, similar problems
might exist with other controllers.
Signed-off-by: Jens Kehne <jens.kehne@agilent.com>
Link: https://lore.kernel.org/r/20250804133754.3496718-1-jens.kehne@agilent.com
Signed-off-by: Lee Jones <lee@kernel.org>
Testing has shown that reading multiple registers at once (for 10-bit
ADC values) does not work. Set the use_single_read regmap_config flag
to make regmap split these for us.
This should fix temperature opregion accesses done by
drivers/acpi/pmic/intel_pmic_chtdc_ti.c and is also necessary for
the upcoming drivers for the ADC and battery MFD cells.
Fixes: 6bac0606fd ("mfd: Add support for Cherry Trail Dollar Cove TI PMIC")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Hans de Goede <hansg@kernel.org>
Link: https://lore.kernel.org/r/20250804133240.312383-1-hansg@kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
guard() makes sure that the mutex gets unlocked when the function returns
and thus removes the need for unlock gotos or similar mechanisms and
therefore allows for a simpler function structure.
So convert the qnap_mcu_exec function to use it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250804130726.3180806-4-heiko@sntech.de
Signed-off-by: Lee Jones <lee@kernel.org>
Relying on other components to include those basic types is unreliable
and may cause compile errors like:
../include/linux/mfd/qnap-mcu.h:13:9: error: unknown type name ‘u32’
13 | u32 baud_rate;
| ^~~
../include/linux/mfd/qnap-mcu.h:17:9: error: unknown type name ‘bool’
17 | bool usb_led;
| ^~~~
So make sure, the types used in the header are available.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250804130726.3180806-2-heiko@sntech.de
Signed-off-by: Lee Jones <lee@kernel.org>
Add the TS233 compatible and affiliated driver data to qnap-mcu.
The TS233 is mostly similar to the TS433, except not having any of the
PCIe components, so there are only 2 drives.
The fan pwm-limits from the vendor-configuration also are the same
as for the ts433 variant.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250730173423.1878599-3-heiko@sntech.de
Signed-off-by: Lee Jones <lee@kernel.org>
