Originally the SCSI subsystem has been using 'special' SCSI status codes,
which were the SAM-specified ones but shifted by 1. As most drivers have
now been modified to use the SAM-specified ones, having two nearly
identical sets of definitions only causes confusion.
The Linux-specifed SCSI status codes have been marked obsolete for several
years so drop them and use the SAM-specified status codes throughout.
Link: https://lore.kernel.org/r/20210427083046.31620-41-hare@suse.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of setting the message byte translate it to the appropriate host
byte. As error recovery would return DID_ERROR for any non-zero message
byte the translation doesn't change the error handling.
[mkp: zeroday bug report: s/SCpnt->result/SCpnt/]
Link: https://lore.kernel.org/r/20210427083046.31620-33-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The done() function is called with a host_byte indicating the actual error
when the message byte is set. As the host byte takes precedence during
error recovery we can drop setting the message byte if the host byte is
set, too. The only other case is when the host byte is DID_OK, but in that
case the message byte is always COMMAND_COMPLETE (i.e. 0), so we can drop
it there, too.
Link: https://lore.kernel.org/r/20210427083046.31620-31-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of setting the message byte translate it to the appropriate host
byte. As error recovery would return DID_ERROR for any non-zero message
byte the translation doesn't change the error handling. And use SCSI
result accessors while we're at it.
Link: https://lore.kernel.org/r/20210427083046.31620-29-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace the check for DRIVER_SENSE with a check for
scsi_status_is_check_condition().
Audit all callsites to ensure the SAM status is set correctly. For
backwards compability move the DRIVER_SENSE definition to sg.h, and update
sg, bsg, and scsi_ioctl to set the DRIVER_SENSE driver_status whenever
SAM_STAT_CHECK_CONDITION is present.
[mkp: fix zeroday srp warning]
Link: https://lore.kernel.org/r/20210427083046.31620-10-hare@suse.de
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fix
Return the actual error code in __scsi_execute() (which, according to the
documentation, should have happened anyway). And audit all callers to cope
with negative return values from __scsi_execute() and friends.
[mkp: resolve conflict and return bool]
Link: https://lore.kernel.org/r/20210427083046.31620-7-hare@suse.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The description for scsi_mode_sense() claims to return the number of valid
bytes on success, which is not what the code does. Additionally there is
no gain in returning the SCSI status, as everything the callers do is to
check against scsi_result_is_good(), which is what scsi_mode_sense() does
already. So change the calling convention to return a standard error code
on failure, and 0 on success, and adapt the description and all callers.
Link: https://lore.kernel.org/r/20210427083046.31620-4-hare@suse.de
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
From ufshcd_transfer_req_compl():
Resetting interrupt aggregation counters first and reading the
DOOR_BELL afterward allows us to handle all the completed requests. In
order to prevent other interrupts starvation the DB is read once after
reset. The down side of this solution is the possibility of false
interrupt if device completes another request after resetting
aggregation and before reading the DB.
Prevent that ufshcd_intr() reports a false positive "Unhandled interrupt"
message if the above scenario is triggered.
Link: https://lore.kernel.org/r/20210519202058.12634-2-bvanassche@acm.org
Cc: Stanley Chu <stanley.chu@mediatek.com>
Cc: Can Guo <cang@codeaurora.org>
Cc: Bean Huo <beanhuo@micron.com>
Cc: Jaegeuk Kim <jaegeuk@kernel.org>
Cc: Asutosh Das <asutoshd@codeaurora.org>
Suggested-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a firmware fault occurs while scanning the devices during IOC
initialization then the driver issues the hard reset operation to recover
the IOC. However, the driver is not issuing a Port enable request
message as part of hard reset operation during IOC initialization. Due to
this, the driver will not receive get any device discovery-related events
and hence devices will not be accessible.
Teach the driver to gracefully handle firmware faults while scanning for
target devices during IOC initialization. Make the driver issue a port
enable request message as part of hard reset operation. This permits
receiving device discovery-related events from the firmware after the hard
reset operation completes.
Link: https://lore.kernel.org/r/20210518051625.1596742-4-suganath-prabu.subramani@broadcom.com
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The sysfs handling function sdev_store_queue_depth() enforces that the sdev
queue depth cannot exceed shost can_queue. The initial sdev queue depth
comes from shost cmd_per_lun. However, the LLDD may manually set
cmd_per_lun to be larger than can_queue, which leads to an initial sdev
queue depth greater than can_queue.
Such an issue was reported in [0], which caused a hang. That has since been
fixed in commit fc09acb7de ("scsi: scsi_debug: Fix cmd_per_lun, set to
max_queue").
Stop this possibly happening for other drivers by capping shost cmd_per_lun
at shost can_queue.
[0] https://lore.kernel.org/linux-scsi/YHaez6iN2HHYxYOh@T590/
Link: https://lore.kernel.org/r/1621434662-173079-1-git-send-email-john.garry@huawei.com
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Default behavior for the driver, when aborting an I/O, is to terminate the
I/O with the adapter. The adapter will initiate an ABTS to terminate the
exchange on the link and mark the exchange is terminated so that no further
use of the sgl or any traffic for the exchange is worked on. Completion on
the Abort is then posted to the driver, which as the I/O is terminated can
complete the I/O to the OS. This completion may occur prior to the ABTS
handshake completing on the wire. The ABTS handshake can take a long time
to complete with timeouts and retries reaching 60+ seconds. Note: if
retries fail, LOGO occurs.
Some devices want to ensure that the ABTS handshake fully completes (this
device has fully ack'd it) before the I/O completion is posted back to the
OS, where a failed I/O may be retried via a different path.
To support this behavior, an option was added to the driver to change I/O
completion from the Abort cmd completion to the Exchange termination (aka
ABTS) completion.
Link: https://lore.kernel.org/r/20210514195559.119853-10-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a link bounce happens, there is a possibility that responses to
requests posted prior to the link bounce could be received. This is
problematic as the counter to track reglogin completion after link up can
become out of sync with the real state.
As there is no reason to process a request made in a prior link up context,
eliminate all the disturbance by tagging the request with the event_tag
maintained by the SLI Port for the link. The event_tag will change on every
link state transition. As long as the tag matches the current event_tag,
the response can be processed. If it doesn't match, just discard the
response.
Link: https://lore.kernel.org/r/20210514195559.119853-8-jsmart2021@gmail.com
Co-developed-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: Justin Tee <justin.tee@broadcom.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
