HuC firmware css header has almost exactly same definition as GuC
firmware except for the sw_version. Also, add a new member fw_type
into intel_uc_fw to indicate what kind of fw it is. So, the loader
will pull right sw_version from header.
v2: rebased on-top of drm-intel-nightly
v3: rebased. Rename device_id to guc_branch_client_version,
make guc_sw_version a union. <Jeff Mcgee>. Put UC_FW_TYPE_GUC
and UC_FW_TYPE_HUC into an enum.
v4: rebased on top of drm-tip.Update dev to dev_priv in
intel_uc_fw_fetch.
v5: rebased. Add INTEL_ prefix to an enum. Add fw_type declaration
from patch 1.Combine two different unions for huc and guc version,
reserved etc into one union with two structs.
v6: rebased. Change fw_type to enum.
v7: rebased. Rename the enum fw_type to intel_uc_fw_type.
Cc: Michal Wajdeczko <michal.wajdeczko.@intel.com>
Tested-by: Xiang Haihao <haihao.xiang@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484356631-16139-3-git-send-email-anusha.srivatsa@intel.com
Rename some of the GuC fw loading code to make them more general. We
will utilise them for HuC loading as well.
s/intel_guc_fw/intel_uc_fw/g
s/GUC_FIRMWARE/INTEL_UC_FIRMWARE/g
Struct intel_guc_fw is renamed to intel_uc_fw. Prefix of tts members,
such as 'guc' or 'guc_fw' either is renamed to 'uc' or removed for
same purpose.
v2: rebased on top of nightly.
reapplied the search/replace as upstream code as changed.
v3: removed G from messages in shared fw fetch function.
v4: rebased.Updated dev to dev_priv in intel_guc_setup(), guc_fw_getch()
and intel_guc_init().
v5: rebased. Remove uint32_t fw_type to patch 2. Add INTEL_ prefix for
fields in enum intel_uc_fw_status. Remove uc_dev field since its never
used.Rename uc_fw to just fw and guc_fw to fw to avoid redundency.
v6: rebased. Remove sections of code that were commented and no longer
required.
v7: rebased. Remove uc_fw_ prefix from path and obj fields
in intel_uc_fw struct as suggested by Michal.
v8: rebased. Add declaration of intel_guc_wopcm_size() in
this patch instead of patch 3.
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Peter Antoine <peter.antoine@intel.com>
Reviewed-by: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484356631-16139-2-git-send-email-anusha.srivatsa@intel.com
Some engines are never user or already sitting idle in the kernel
context and for those we can skip flushing the current context for
i915_gem_switch_to_kernel_context(). We used to perform this
optimisation but that was removed for convenience of converting over to
multiple timelines and handling the pending request queues.
From the perspective of writing selftests, reducing the number of
background operations on the engines makes defining assertions easier.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170114162334.10271-2-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
drivers/gpu/drm/i915/i915_gpu_error.c: In function ‘i915_error_vprintf’:
drivers/gpu/drm/i915/i915_gpu_error.c:137:3: warning:
function might be possible candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
len = vsnprintf(NULL, 0, f, tmp);
^~~
drivers/gpu/drm/i915/i915_gpu_error.c:144:2: warning:
function might be possible candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
len = vsnprintf(e->buf + e->bytes, e->size - e->bytes, f, args);
^~~
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170114105113.1231-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reading the ggtt_views is much more pleasant without the extra
characters from specifying the union (i.e. ggtt_view.partial rather than
ggtt_view.params.partial). To make this work inside i915_vma_compare()
with only a single memcmp requires us to ensure that there are no
uninitialised bytes within each branch of the union (we make sure the
structs are packed) and we need to store the size of each branch.
v4: Rewrite changelog and add comments explaining the assert.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170114002827.31315-5-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
In preparation for the next patch to convert to using an anonymous union
and leaving the excess bytes in the union uninitialised, we first need
to make sure we do not compare using those uninitialised bytes. We also
want to preserve the compactness of the code, avoiding a second call to
memcmp or introducing a switch, so we take advantage of using the type
as an encoded size (as well as a unique identifier for each type of view).
v2: Add the rationale for why we encode size into ggtt_view.type as a
comment before the memcmp()
v3: Use a switch to also assert that no two i915_ggtt_view_type have the same
value.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170114002827.31315-3-chris@chris-wilson.co.uk
As per bpsec, CHICKEN_TRANS_EDP bit 12 ,15 must be programmed in
psr2 enable sequence.
bit 12 : Program Transcoder EDP VSC DIP header with a valid setting for
PSR2 and Set CHICKEN_TRANS_EDP(0x420cc) bit 12 for programmable
header packet.
bit 15 : Set CHICKEN_TRANS_EDP(0x420cc) bit 15 if Y coordinate is supported
v2: (Rodrigo)
- move CHICKEN_TRANS_EDP bit set logic right after setup_vsc
v3:(Rodrigo)
- initialize chicken_trans to CHICKEN_TRANS_BIT12 instead of 0
v4:(chris wilson)
- use BIT(12), remove CHICKEN_TRANS_BIT12
- remove unnecessary comments
- update commit message
v5:
- rename bit 12 PSR2_VSC_ENABLE_PROG_HEADER
- rename bit 15 PSR2_ADD_VERTICAL_LINE_COUNT
v6:(Rodrigo)
- remove TRANS_EDP=3, use cpu_transcoder
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: vathsala nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484247691-20930-1-git-send-email-vathsala.nagaraju@intel.com
Psr1 and psr2 are mutually exclusive,ie when psr2 is enabled,
psr1 should be disabled.When psr2 is exited , bit 31 of reg
PSR2_CTL must be set to 0 but currently bit 31 of SRD_CTL
(psr1 control register)is set to 0.
Also ,PSR2_IDLE state is looked up from SRD_STATUS(psr1 register)
instead of PSR2_STATUS register, which has wrong data, resulting
in blankscreen.
hsw_enable_source is split into hsw_enable_source_psr1 and
hsw_enable_source_psr2 for easier code review and maintenance,
as suggested by rodrigo and jim.
v2: (Rodrigo)
- Rename hsw_enable_source_psr* to intel_enable_source_psr*
v3: (Rodrigo)
- In hsw_psr_disable ,
1) for psr active case, handle psr2 followed by psr1.
2) psr inactive case, handle psr2 followed by psr1
v4:(Rodrigo)
- move psr2 restriction(32X20) to match_conditions function
returning false and fully blocking PSR to a new patch before
this one.
v5: in source_psr2, removed val = EDP_PSR_ENABLE
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Vathsala Nagaraju <vathsala.nagaraju@intel.com>
Signed-off-by: Patil Deepti <deepti.patil@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484244059-9201-1-git-send-email-vathsala.nagaraju@intel.com
The WaDisableLSQCROPERFforOCL workaround has the side effect of
disabling an L3SQ optimization that has huge performance implications
and is unlikely to be necessary for the correct functioning of usual
graphic workloads. Userspace is free to re-enable the workaround on
demand, and is generally in a better position to determine whether the
workaround is necessary than the DRM is (e.g. only during the
execution of compute kernels that rely on both L3 fences and HDC R/W
requests).
The same workaround seems to apply to BDW (at least to production
stepping G1) and SKL as well (the internal workaround database claims
that it does for all steppings, while the BSpec workaround table only
mentions pre-production steppings), but the DRM doesn't do anything
beyond whitelisting the L3SQCREG4 register so userspace can enable it
when it sees fit. Do the same on KBL platforms.
Improves performance of the GFXBench4 gl_manhattan31 benchmark by 60%,
and gl_4 (AKA car chase) by 14% on a KBL GT2 running Mesa master --
This is followed by a regression of 35% and 10% respectively for the
same benchmarks and platform caused by my recent patch series
switching userspace to use the dataport constant cache instead of the
sampler to implement uniform pull constant loads, which caused us to
hit more heavily the L3 cache (and on platforms other than KBL had the
opposite effect of improving performance of the same two benchmarks).
The overall effect on KBL of this change combined with the recent
userspace change is respectively 4.6% and 2.6%. SynMark2 OglShMapPcf
was affected by the constant cache changes (though it improved as it
did on other platforms rather than regressing), but is not
significantly affected by this patch (with statistical significance of
5% and sample size 20).
v2: Drop some more code to avoid unused variable warning.
Fixes: 738fa1b312 ("drm/i915/kbl: Add WaDisableLSQCROPERFforOCL")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99256
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: beignet@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v4.7+
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[Removed double Fixes tag]
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1484217894-20505-1-git-send-email-mika.kuoppala@intel.com
This patch adds the DP MST audio support on i915 platform and
it will enable dyn_pcm_assign feature.
DP MST supports several device entry on the same port and each
device entry can map to one pcm stream. For example, on i915,
there are 3 pins, and each pin has 3 device entries. This means
there should be 3x3 pcms. However, there is only 3 pipe lines in
i915. This means 3 pcms are actived at most at the same moment.
We will create 5 pcms (pin number + dev entry num - 1) in this case.
For the details, please refer commit a76056f2e5
("ALSA: hda - hdmi dynamically bind PCM to pin when monitor hotplug")
Each device entry is a virtual pin. It is described by pin_nid and dev_id
in struct hdmi_spec_per_pin.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Libin Yang <libin.yang@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1484208294-8637-3-git-send-email-libin.yang@intel.com
