Mat Martineau says:
====================
mptcp: Properly clean up unaccepted subflows
Patch 1 factors out part of the mptcp_close() function for use by a caller
that already owns the socket lock. This is a prerequisite for patch 2.
Patch 2 is the fix that fully cleans up the unaccepted subflow sockets.
====================
Link: https://lore.kernel.org/r/20220927193158.195729-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The mptcp socket and its subflow sockets in accept queue can't be
released after the process exit.
While the release of a mptcp socket in listening state, the
corresponding tcp socket will be released too. Meanwhile, the tcp
socket in the unaccept queue will be released too. However, only init
subflow is in the unaccept queue, and the joined subflow is not in the
unaccept queue, which makes the joined subflow won't be released, and
therefore the corresponding unaccepted mptcp socket will not be released
to.
This can be reproduced easily with following steps:
1. create 2 namespace and veth:
$ ip netns add mptcp-client
$ ip netns add mptcp-server
$ sysctl -w net.ipv4.conf.all.rp_filter=0
$ ip netns exec mptcp-client sysctl -w net.mptcp.enabled=1
$ ip netns exec mptcp-server sysctl -w net.mptcp.enabled=1
$ ip link add red-client netns mptcp-client type veth peer red-server \
netns mptcp-server
$ ip -n mptcp-server address add 10.0.0.1/24 dev red-server
$ ip -n mptcp-server address add 192.168.0.1/24 dev red-server
$ ip -n mptcp-client address add 10.0.0.2/24 dev red-client
$ ip -n mptcp-client address add 192.168.0.2/24 dev red-client
$ ip -n mptcp-server link set red-server up
$ ip -n mptcp-client link set red-client up
2. configure the endpoint and limit for client and server:
$ ip -n mptcp-server mptcp endpoint flush
$ ip -n mptcp-server mptcp limits set subflow 2 add_addr_accepted 2
$ ip -n mptcp-client mptcp endpoint flush
$ ip -n mptcp-client mptcp limits set subflow 2 add_addr_accepted 2
$ ip -n mptcp-client mptcp endpoint add 192.168.0.2 dev red-client id \
1 subflow
3. listen and accept on a port, such as 9999. The nc command we used
here is modified, which makes it use mptcp protocol by default.
$ ip netns exec mptcp-server nc -l -k -p 9999
4. open another *two* terminal and use each of them to connect to the
server with the following command:
$ ip netns exec mptcp-client nc 10.0.0.1 9999
Input something after connect to trigger the connection of the second
subflow. So that there are two established mptcp connections, with the
second one still unaccepted.
5. exit all the nc command, and check the tcp socket in server namespace.
And you will find that there is one tcp socket in CLOSE_WAIT state
and can't release forever.
Fix this by closing all of the unaccepted mptcp socket in
mptcp_subflow_queue_clean() with __mptcp_close().
Now, we can ensure that all unaccepted mptcp sockets will be cleaned by
__mptcp_close() before they are released, so mptcp_sock_destruct(), which
is used to clean the unaccepted mptcp socket, is not needed anymore.
The selftests for mptcp is ran for this commit, and no new failures.
Fixes: f296234c98 ("mptcp: Add handling of incoming MP_JOIN requests")
Fixes: 6aeed90450 ("mptcp: fix race on unaccepted mptcp sockets")
Cc: stable@vger.kernel.org
Reviewed-by: Jiang Biao <benbjiang@tencent.com>
Reviewed-by: Mengen Sun <mengensun@tencent.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Menglong Dong <imagedong@tencent.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
ice: xsk: ZC changes
Maciej Fijalkowski says:
This set consists of two fixes to issues that were either pointed out on
indirectly (John was reviewing AF_XDP selftests that were testing ice's
ZC support) mailing list or were directly reported by customers.
First patch allows user space to see done descriptor in CQ even after a
single frame being transmitted and second patch removes the need for
having HW rings sized to power of 2 number of descriptors when used
against AF_XDP.
I also forgot to mention that due to the current Tx cleaning algorithm,
4k HW ring was broken and these two patches bring it back to life, so we
kill two birds with one stone.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: xsk: drop power of 2 ring size restriction for AF_XDP
ice: xsk: change batched Tx descriptor cleaning
====================
Link: https://lore.kernel.org/r/20220927164112.4011983-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the following set of commands fails:
$ ip link add br0 type bridge # vlan_filtering 0
$ ip link set swp0 master br0
$ bridge vlan
port vlan-id
swp0 1 PVID Egress Untagged
$ bridge vlan add dev swp0 vid 10
Error: mscc_ocelot_switch_lib: Port with more than one egress-untagged VLAN cannot have egress-tagged VLANs.
Dumping ocelot->vlans, one can see that the 2 egress-untagged VLANs on swp0 are
vid 1 (the bridge PVID) and vid 4094, a PVID used privately by the driver for
VLAN-unaware bridging. So this is why bridge vid 10 is refused, despite
'bridge vlan' showing a single egress untagged VLAN.
As mentioned in the comment added, having this private VLAN does not impose
restrictions to the hardware configuration, yet it is a bookkeeping problem.
There are 2 possible solutions.
One is to make the functions that operate on VLAN-unaware pvids:
- ocelot_add_vlan_unaware_pvid()
- ocelot_del_vlan_unaware_pvid()
- ocelot_port_setup_dsa_8021q_cpu()
- ocelot_port_teardown_dsa_8021q_cpu()
call something different than ocelot_vlan_member_(add|del)(), the latter being
the real problem, because it allocates a struct ocelot_bridge_vlan *vlan which
it adds to ocelot->vlans. We don't really *need* the private VLANs in
ocelot->vlans, it's just that we have the extra convenience of having the
vlan->portmask cached in software (whereas without these structures, we'd have
to create a raw ocelot_vlant_rmw_mask() procedure which reads back the current
port mask from hardware).
The other solution is to filter out the private VLANs from
ocelot_port_num_untagged_vlans(), since they aren't what callers care about.
We only need to do this to the mentioned function and not to
ocelot_port_num_tagged_vlans(), because private VLANs are never egress-tagged.
Nothing else seems to be broken in either solution, but the first one requires
more rework which will conflict with the net-next change 36a0bf4435 ("net:
mscc: ocelot: set up tag_8021q CPU ports independent of user port affinity"),
and I'd like to avoid that. So go with the other one.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220927122042.1100231-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2022-09-28
The patch is by me and targets the c_can driver. It disables an
optimization in the TX path of C_CAN cores which causes problems.
* tag 'linux-can-fixes-for-6.0-20220928' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: c_can: don't cache TX messages for C_CAN cores
====================
Link: https://lore.kernel.org/r/20220928090629.1124190-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
AF_XDP Tx descriptor cleaning in ice driver currently works in a "lazy"
way - descriptors are not cleaned immediately after send. We rather hold
on with cleaning until we see that free space in ring drops below
particular threshold. This was supposed to reduce the amount of
unnecessary work related to cleaning and instead of keeping the ring
empty, ring was rather saturated.
In AF_XDP realm cleaning Tx descriptors implies producing them to CQ.
This is a way of letting know user space that particular descriptor has
been sent, as John points out in [0].
We tried to implement serial descriptor cleaning which would be used in
conjunction with batched cleaning but it made code base more convoluted
and probably harder to maintain in future. Therefore we step away from
batched cleaning in a current form in favor of an approach where we set
RS bit on every last descriptor from a batch and clean always at the
beginning of ice_xmit_zc().
This means that we give up a bit of Tx performance, but this doesn't
hurt l2fwd scenario which is way more meaningful than txonly as this can
be treaten as AF_XDP based packet generator. l2fwd is not hurt due to
the fact that Tx side is much faster than Rx and Rx is the one that has
to catch Tx up.
FWIW Tx descriptors are still produced in a batched way.
[0]: https://lore.kernel.org/bpf/62b0a20232920_3573208ab@john.notmuch/
Fixes: 126cdfe100 ("ice: xsk: Improve AF_XDP ZC Tx and use batching API")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This commit fixes DMA engine reset timeout issue in suspend/resume
with ADLink I-Pi SMARC Plus board which dmesg shows:
...
[ 54.678271] PM: suspend exit
[ 54.754066] intel-eth-pci 0000:00:1d.2 enp0s29f2: PHY [stmmac-3:01] driver [Maxlinear Ethernet GPY215B] (irq=POLL)
[ 54.755808] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-0
...
[ 54.780482] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-7
[ 55.784098] intel-eth-pci 0000:00:1d.2: Failed to reset the dma
[ 55.784111] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_hw_setup: DMA engine initialization failed
[ 55.784115] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_open: Hw setup failed
...
The issue is related with serdes which impacts clock. There is
serdes in ADLink I-Pi SMARC board ethernet controller. Please refer to
commit b9663b7ca6 ("net: stmmac: Enable SERDES power up/down sequence")
for detial. When issue is reproduced, DMA engine clock is not ready
because serdes is not powered up.
To reproduce DMA engine reset timeout issue with hardware which has
serdes in GBE controller, install Ubuntu. In Ubuntu GUI, click
"Power Off/Log Out" -> "Suspend" menu, it disables network interface,
then goes to sleep mode. When it wakes up, it enables network
interface again. Stmmac driver is called in this way:
1. stmmac_release: Stop network interface. In this function, it
disables DMA engine and network interface;
2. stmmac_suspend: It is called in kernel suspend flow. But because
network interface has been disabled(netif_running(ndev) is
false), it does nothing and returns directly;
3. System goes into S3 or S0ix state. Some time later, system is
waken up by keyboard or mouse;
4. stmmac_resume: It does nothing because network interface has
been disabled;
5. stmmac_open: It is called to enable network interace again. DMA
engine is initialized in this API, but serdes is not power on so
there will be DMA engine reset timeout issue.
Similarly, serdes powerdown should be added in stmmac_release.
Network interface might be disabled by cmd "ifconfig eth0 down",
DMA engine, phy and mac have been disabled in ndo_stop callback,
serdes should be powered down as well. It doesn't make sense that
serdes is on while other components have been turned off.
If ethernet interface is in enabled state(netif_running(ndev) is true)
before suspend/resume, the issue couldn't be reproduced because serdes
could be powered up in stmmac_resume.
Because serdes_powerup is added in stmmac_open, it doesn't need to be
called in probe function.
Fixes: b9663b7ca6 ("net: stmmac: Enable SERDES power up/down sequence")
Signed-off-by: Junxiao Chang <junxiao.chang@intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Jimmy JS Chen <jimmyjs.chen@adlinktech.com>
Tested-by: Looi, Hong Aun <hong.aun.looi@intel.com>
Link: https://lore.kernel.org/r/20220923050448.1220250-1-junxiao.chang@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit 6911458dc4 ("wifi: mac80211: mlme: refactor assoc success
handling") moved the per-link setup out of ieee80211_assoc_success() into a
new function ieee80211_assoc_config_link() but missed to remove the unlock
of 'sta_mtx' in case of HE capability/operation missing on HE AP, which
leads to a double unlock:
ieee80211_assoc_success() {
...
ieee80211_assoc_config_link() {
...
if (!(link->u.mgd.conn_flags & IEEE80211_CONN_DISABLE_HE) &&
(!elems->he_cap || !elems->he_operation)) {
mutex_unlock(&sdata->local->sta_mtx);
...
}
...
}
...
mutex_unlock(&sdata->local->sta_mtx);
...
}
Fixes: 6911458dc4 ("wifi: mac80211: mlme: refactor assoc success handling")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Link: https://lore.kernel.org/r/20220925143420.784975-1-rafaelmendsr@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During our testing of WFM200 module over SDIO on i.MX6Q-based platform,
we discovered a memory corruption on the system, tracing back to the wfx
driver. Using kfence, it was possible to trace it back to the root
cause, which is hw->max_rates set to 8 in wfx_init_common,
while the maximum defined by IEEE80211_TX_TABLE_SIZE is 4.
This causes array out-of-bounds writes during updates of the rate table,
as seen below:
BUG: KFENCE: memory corruption in kfree_rcu_work+0x320/0x36c
Corrupted memory at 0xe0a4ffe0 [ 0x03 0x03 0x03 0x03 0x01 0x00 0x00
0x02 0x02 0x02 0x09 0x00 0x21 0xbb 0xbb 0xbb ] (in kfence-#81):
kfree_rcu_work+0x320/0x36c
process_one_work+0x3ec/0x920
worker_thread+0x60/0x7a4
kthread+0x174/0x1b4
ret_from_fork+0x14/0x2c
0x0
kfence-#81: 0xe0a4ffc0-0xe0a4ffdf, size=32, cache=kmalloc-64
allocated by task 297 on cpu 0 at 631.039555s:
minstrel_ht_update_rates+0x38/0x2b0 [mac80211]
rate_control_tx_status+0xb4/0x148 [mac80211]
ieee80211_tx_status_ext+0x364/0x1030 [mac80211]
ieee80211_tx_status+0xe0/0x118 [mac80211]
ieee80211_tasklet_handler+0xb0/0xe0 [mac80211]
tasklet_action_common.constprop.0+0x11c/0x148
__do_softirq+0x1a4/0x61c
irq_exit+0xcc/0x104
call_with_stack+0x18/0x20
__irq_svc+0x80/0xb0
wq_worker_sleeping+0x10/0x100
wq_worker_sleeping+0x10/0x100
schedule+0x50/0xe0
schedule_timeout+0x2e0/0x474
wait_for_completion+0xdc/0x1ec
mmc_wait_for_req_done+0xc4/0xf8
mmc_io_rw_extended+0x3b4/0x4ec
sdio_io_rw_ext_helper+0x290/0x384
sdio_memcpy_toio+0x30/0x38
wfx_sdio_copy_to_io+0x88/0x108 [wfx]
wfx_data_write+0x88/0x1f0 [wfx]
bh_work+0x1c8/0xcc0 [wfx]
process_one_work+0x3ec/0x920
worker_thread+0x60/0x7a4
kthread+0x174/0x1b4
ret_from_fork+0x14/0x2c 0x0
After discussion on the wireless mailing list it was clarified
that the issue has been introduced by:
commit ee0e16ab75 ("mac80211: minstrel_ht: fill all requested rates")
and fix shall be in minstrel_ht_update_rates in rc80211_minstrel_ht.c.
Fixes: ee0e16ab75 ("mac80211: minstrel_ht: fill all requested rates")
Link: https://lore.kernel.org/all/12e5adcd-8aed-f0f7-70cc-4fb7b656b829@camlingroup.com/
Link: https://lore.kernel.org/linux-wireless/20220915131445.30600-1-lech.perczak@camlingroup.com/
Cc: Jérôme Pouiller <jerome.pouiller@silabs.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Seiderer <ps.report@gmx.net>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Krzysztof Drobiński <krzysztof.drobinski@camlingroup.com>,
Signed-off-by: Paweł Lenkow <pawel.lenkow@camlingroup.com>
Signed-off-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Peter Seiderer <ps.report@gmx.net>
Reviewed-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 10cb8e6175 ("mac80211: enable QoS support for nl80211 ctrl port")
changed ieee80211_tx_control_port() to aways call
__ieee80211_select_queue() without checking local->hw.queues.
__ieee80211_select_queue() returns a queue-id between 0 and 3, which means
that now ieee80211_tx_control_port() may end up setting the queue-mapping
for a skb to a value higher then local->hw.queues if local->hw.queues
is less then 4.
Specifically this is a problem for ralink rt2500-pci cards where
local->hw.queues is 2. There this causes rt2x00queue_get_tx_queue() to
return NULL and the following error to be logged: "ieee80211 phy0:
rt2x00mac_tx: Error - Attempt to send packet over invalid queue 2",
after which association with the AP fails.
Other callers of __ieee80211_select_queue() skip calling it when
local->hw.queues < IEEE80211_NUM_ACS, add the same check to
ieee80211_tx_control_port(). This fixes ralink rt2500-pci and
similar cards when less then 4 tx-queues no longer working.
Fixes: 10cb8e6175 ("mac80211: enable QoS support for nl80211 ctrl port")
Cc: Markus Theil <markus.theil@tu-ilmenau.de>
Suggested-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220918192052.443529-1-hdegoede@redhat.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make sure local->queue_stop_reasons and vif.txqs_stopped stay in sync.
When a new vif is created the queues may end up in an inconsistent state
and be inoperable:
Communication not using iTXQ will work, allowing to e.g. complete the
association. But the 4-way handshake will time out. The sta will not
send out any skbs queued in iTXQs.
All normal attempts to start the queues will fail when reaching this
state.
local->queue_stop_reasons will have marked all queues as operational but
vif.txqs_stopped will still be set, creating an inconsistent internal
state.
In reality this seems to be race between the mac80211 function
ieee80211_do_open() setting SDATA_STATE_RUNNING and the wake_txqs_tasklet:
Depending on the driver and the timing the queues may end up to be
operational or not.
Cc: stable@vger.kernel.org
Fixes: f856373e2f ("wifi: mac80211: do not wake queues on a vif that is being stopped")
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20220915130946.302803-1-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ieee80211_txq_purge() calls fq_tin_reset() and
ieee80211_purge_tx_queue(); Both are then calling
ieee80211_free_txskb(). Which can decide to TX the skb again.
There are at least two ways to get a deadlock:
1) When we have a TDLS teardown packet queued in either tin or frags
ieee80211_tdls_td_tx_handle() will call ieee80211_subif_start_xmit()
while we still hold fq->lock. ieee80211_txq_enqueue() will thus
deadlock.
2) A variant of the above happens if aggregation is up and running:
In that case ieee80211_iface_work() will deadlock with the original
task: The original tasks already holds fq->lock and tries to get
sta->lock after kicking off ieee80211_iface_work(). But the worker
can get sta->lock prior to the original task and will then spin for
fq->lock.
Avoid these deadlocks by not sending out any skbs when called via
ieee80211_free_txskb().
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Link: https://lore.kernel.org/r/20220915124120.301918-1-alexander@wetzel-home.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The label passed to the QDESC_GET for the ETHOFLD TXQ, RXQ, and FLQ, is the
'out' one, which skips the 'out_unlock' label, and thus doesn't unlock the
'uld_mutex' before returning. Additionally, since commit 5148e5950c
("cxgb4: add EOTID tracking and software context dump"), the access to
these ETHOFLD hardware queues should be protected by the 'mqprio_mutex'
instead.
Fixes: 2d0cb84dd9 ("cxgb4: add ETHOFLD hardware queue support")
Fixes: 5148e5950c ("cxgb4: add EOTID tracking and software context dump")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Reviewed-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Link: https://lore.kernel.org/r/20220922175109.764898-1-rafaelmendsr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit fe2c9c61f6.
On Tue, Sep 13, 2022 at 05:48:58PM +0100, Russell King (Oracle) wrote:
>What happens if this is built as a module, and the module is loaded,
>binds (and creates the directory), then is removed, and then re-
>inserted? Nothing removes the old directory, so doesn't
>debugfs_create_dir() fail, resulting in subsequent failure to add
>any subsequent debugfs entries?
>
>I don't think this patch should be backported to stable trees until
>this point is addressed.
Revert until a proper fix is available as the original behavior was
better.
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: stable@kernel.org
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: fe2c9c61f6 ("net: mvpp2: debugfs: fix memory leak when using debugfs_lookup()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220923234736.657413-1-sashal@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The datasheet [1] explicit describes it as requirement for a reset.
[1] MT7531 Reference Manual for Development Board rev 1.0, page 735
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move the PLL init of the switch out of the pad configuration of the port
6 (usally cpu port).
Fix a unidirectional 100 mbit limitation on 1 gbit or 2.5 gbit links for
outbound traffic on port 5 or port 6.
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit bbb774d921 ("net: Add tests for bonding and team address list
management") adds the net team driver tests in the directory:
tools/testing/selftests/drivers/net/team/
The file entry in MAINTAINERS for the TEAM DRIVER however refers to:
tools/testing/selftests/net/team/
Hence, ./scripts/get_maintainer.pl --self-test=patterns complains about a
broken file pattern.
Repair this file entry in TEAM DRIVER.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Benjamin Poirier <bpoirier@nvidia.com>
Link: https://lore.kernel.org/r/20220922114053.10883-1-lukas.bulwahn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When GEM is in SGMII mode and disabled as a wakeup source, the power
management controller can power down the entire full power domain(FPD)
if none of the FPD devices are in use.
Incase of FPD off, there are below ethernet link up issues on non-wakeup
suspend/resume. To fix it add phy_exit() in suspend and phy_init() in the
resume path which reinitializes PS GTR SGMII lanes.
$ echo +20 > /sys/class/rtc/rtc0/wakealarm
$ echo mem > /sys/power/state
After resume:
$ ifconfig eth0 up
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
phy phy-fd400000.phy.0: phy poweron failed --> -110
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
SIOCSIFFLAGS: Connection timed out
phy phy-fd400000.phy.0: phy poweron failed --> -110
Fixes: 8b73fa3ae0 ("net: macb: Added ZynqMP-specific initialization")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for not enabling carrier during TUNSETIFF
interface creation by specifying the IFF_NO_CARRIER flag.
Our tests make heavy use of tun interfaces. In some scenarios, the test
process creates the interface but another process brings it up after the
interface is discovered via netlink notification. In that case, it is
not possible to create a tun/tap interface with carrier off without it
racing against the bring up. Immediately setting carrier off via
TUNSETCARRIER is still too late.
Signed-off-by: Patrick Rohr <prohr@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from Jakub Kicinski:
"Including fixes from wifi, netfilter and can.
A handful of awaited fixes here - revert of the FEC changes, bluetooth
fix, fixes for iwlwifi spew.
We added a warning in PHY/MDIO code which is triggering on a couple of
platforms in a false-positive-ish way. If we can't iron that out over
the week we'll drop it and re-add for 6.1.
I've added a new "follow up fixes" section for fixes to fixes in
6.0-rcs but it may actually give the false impression that those are
problematic or that more testing time would have caught them. So
likely a one time thing.
Follow up fixes:
- nf_tables_addchain: fix nft_counters_enabled underflow
- ebtables: fix memory leak when blob is malformed
- nf_ct_ftp: fix deadlock when nat rewrite is needed
Current release - regressions:
- Revert "fec: Restart PPS after link state change" and the related
"net: fec: Use a spinlock to guard `fep->ptp_clk_on`"
- Bluetooth: fix HCIGETDEVINFO regression
- wifi: mt76: fix 5 GHz connection regression on mt76x0/mt76x2
- mptcp: fix fwd memory accounting on coalesce
- rwlock removal fall out:
- ipmr: always call ip{,6}_mr_forward() from RCU read-side
critical section
- ipv6: fix crash when IPv6 is administratively disabled
- tcp: read multiple skbs in tcp_read_skb()
- mdio_bus_phy_resume state warning fallout:
- eth: ravb: fix PHY state warning splat during system resume
- eth: sh_eth: fix PHY state warning splat during system resume
Current release - new code bugs:
- wifi: iwlwifi: don't spam logs with NSS>2 messages
- eth: mtk_eth_soc: enable XDP support just for MT7986 SoC
Previous releases - regressions:
- bonding: fix NULL deref in bond_rr_gen_slave_id
- wifi: iwlwifi: mark IWLMEI as broken
Previous releases - always broken:
- nf_conntrack helpers:
- irc: tighten matching on DCC message
- sip: fix ct_sip_walk_headers
- osf: fix possible bogus match in nf_osf_find()
- ipvlan: fix out-of-bound bugs caused by unset skb->mac_header
- core: fix flow symmetric hash
- bonding, team: unsync device addresses on ndo_stop
- phy: micrel: fix shared interrupt on LAN8814"
* tag 'net-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
selftests: forwarding: add shebang for sch_red.sh
bnxt: prevent skb UAF after handing over to PTP worker
net: marvell: Fix refcounting bugs in prestera_port_sfp_bind()
net: sched: fix possible refcount leak in tc_new_tfilter()
net: sunhme: Fix packet reception for len < RX_COPY_THRESHOLD
udp: Use WARN_ON_ONCE() in udp_read_skb()
selftests: bonding: cause oops in bond_rr_gen_slave_id
bonding: fix NULL deref in bond_rr_gen_slave_id
net: phy: micrel: fix shared interrupt on LAN8814
net/smc: Stop the CLC flow if no link to map buffers on
ice: Fix ice_xdp_xmit() when XDP TX queue number is not sufficient
net: atlantic: fix potential memory leak in aq_ndev_close()
can: gs_usb: gs_usb_set_phys_id(): return with error if identify is not supported
can: gs_usb: gs_can_open(): fix race dev->can.state condition
can: flexcan: flexcan_mailbox_read() fix return value for drop = true
net: sh_eth: Fix PHY state warning splat during system resume
net: ravb: Fix PHY state warning splat during system resume
netfilter: nf_ct_ftp: fix deadlock when nat rewrite is needed
netfilter: ebtables: fix memory leak when blob is malformed
netfilter: nf_tables: fix percpu memory leak at nf_tables_addchain()
...
Pull EFI fixes from Ard Biesheuvel:
- Use the right variable to check for shim insecure mode
- Wipe setup_data field when booting via EFI
- Add missing error check to efibc driver
* tag 'efi-urgent-for-v6.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: libstub: check Shim mode using MokSBStateRT
efi: x86: Wipe setup_data on pure EFI boot
efi: efibc: Guard against allocation failure
Pull gpio fixes from Bartosz Golaszewski:
- fix a NULL-pointer dereference at driver unbind and a potential
resource leak in error path in gpio-mockup
- make the irqchip immutable in gpio-ftgpio010
- fix dereferencing a potentially uninitialized variable in gpio-tqmx86
- fix interrupt registering in gpiolib's character device code
* tag 'gpio-fixes-for-v6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpiolib: cdev: Set lineevent_state::irq after IRQ register successfully
gpio: tqmx86: fix uninitialized variable girq
gpio: ftgpio010: Make irqchip immutable
gpio: mockup: Fix potential resource leakage when register a chip
gpio: mockup: fix NULL pointer dereference when removing debugfs
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix polling of system-wide events related to mixing per-cpu and
per-thread events.
- Do not check if /proc/modules is unchanged when copying /proc/kcore,
that doesn't get in the way of post processing analysis.
- Include program header in ELF files generated for JIT files, so that
they can be opened by tools using elfutils libraries.
- Enter namespaces when synthesizing build-ids.
- Fix some bugs related to a recent cpu_map overhaul where we should be
using an index and not the cpu number.
- Fix BPF program ELF section name, using the naming expected by libbpf
when using BPF counters in 'perf stat'.
- Add a new test for perf stat cgroup BPF counter.
- Adjust check on 'perf test wp' for older kernels, where the
PERF_EVENT_IOC_MODIFY_ATTRIBUTES ioctl isn't supported.
- Sync x86 cpufeatures with the kernel sources, no changes in tooling.
* tag 'perf-tools-fixes-for-v6.0-2022-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf tools: Honor namespace when synthesizing build-ids
tools headers cpufeatures: Sync with the kernel sources
perf kcore_copy: Do not check /proc/modules is unchanged
libperf evlist: Fix polling of system-wide events
perf record: Fix cpu mask bit setting for mixed mmaps
perf test: Skip wp modify test on old kernels
perf jit: Include program header in ELF files
perf test: Add a new test for perf stat cgroup BPF counter
perf stat: Use evsel->core.cpus to iterate cpus in BPF cgroup counters
perf stat: Fix cpu map index in bperf cgroup code
perf stat: Fix BPF program section name
RHEL/Fedora RPM build checks are stricter, and complain when executable
files don't have a shebang line, e.g.
*** WARNING: ./kselftests/net/forwarding/sch_red.sh is executable but has no shebang, removing executable bit
Fix it by adding shebang line.
Fixes: 6cf0291f95 ("selftests: forwarding: Add a RED test for SW datapath")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Link: https://lore.kernel.org/r/20220922024453.437757-1-liuhangbin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When reading the timestamp is required bnxt_tx_int() hands
over the ownership of the completed skb to the PTP worker.
The skb should not be used afterwards, as the worker may
run before the rest of our code and free the skb, leading
to a use-after-free.
Since dev_kfree_skb_any() accepts NULL make the loss of
ownership more obvious and set skb to NULL.
Fixes: 83bb623c96 ("bnxt_en: Transmit and retrieve packet timestamps")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220921201005.335390-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In prestera_port_sfp_bind(), there are two refcounting bugs:
(1) we should call of_node_get() before of_find_node_by_name() as
it will automaitcally decrease the refcount of 'from' argument;
(2) we should call of_node_put() for the break of the iteration
for_each_child_of_node() as it will automatically increase and
decrease the 'child'.
Fixes: 52323ef754 ("net: marvell: prestera: add phylink support")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Link: https://lore.kernel.org/r/20220921133245.4111672-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a separate receive path for small packets (under 256 bytes).
Instead of allocating a new dma-capable skb to be used for the next packet,
this path allocates a skb and copies the data into it (reusing the existing
sbk for the next packet). There are two bytes of junk data at the beginning
of every packet. I believe these are inserted in order to allow aligned DMA
and IP headers. We skip over them using skb_reserve. Before copying over
the data, we must use a barrier to ensure we see the whole packet. The
current code only synchronizes len bytes, starting from the beginning of
the packet, including the junk bytes. However, this leaves off the final
two bytes in the packet. Synchronize the whole packet.
To reproduce this problem, ping a HME with a payload size between 17 and
214
$ ping -s 17 <hme_address>
which will complain rather loudly about the data mismatch. Small packets
(below 60 bytes on the wire) do not have this issue. I suspect this is
related to the padding added to increase the minimum packet size.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220920235018.1675956-1-seanga2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jonathan Toppins says:
====================
bonding: fix NULL deref in bond_rr_gen_slave_id
Fix a NULL dereference of the struct bonding.rr_tx_counter member because
if a bond is initially created with an initial mode != zero (Round Robin)
the memory required for the counter is never created and when the mode is
changed there is never any attempt to verify the memory is allocated upon
switching modes.
====================
Link: https://lore.kernel.org/r/cover.1663694476.git.jtoppins@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This bonding selftest used to cause a kernel oops on aarch64
and should be architectures agnostic.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There might be a potential race between SMC-R buffer map and
link group termination.
smc_smcr_terminate_all() | smc_connect_rdma()
--------------------------------------------------------------
| smc_conn_create()
for links in smcibdev |
schedule links down |
| smc_buf_create()
| \- smcr_buf_map_usable_links()
| \- no usable links found,
| (rmb->mr = NULL)
|
| smc_clc_send_confirm()
| \- access conn->rmb_desc->mr[]->rkey
| (panic)
During reboot and IB device module remove, all links will be set
down and no usable links remain in link groups. In such situation
smcr_buf_map_usable_links() should return an error and stop the
CLC flow accessing to uninitialized mr.
Fixes: b9247544c1 ("net/smc: convert static link ID instances to support multiple links")
Signed-off-by: Wen Gu <guwen@linux.alibaba.com>
Link: https://lore.kernel.org/r/1663656189-32090-1-git-send-email-guwen@linux.alibaba.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
