When a data traffic with size greater than 1500 is initiated,
say size 65500, it is sent as a set of AMSDUs (3 MSDUs)
in a MPDU.
These AMSDUs are incorrectly classified as multicast
and peer id gets changed, except for first msdu,
because of mcast_bcast bit derived from rx_desc
for every msdu received.
The mcast_bcast bit in rx_desc is only valid for
first msdu. Hence, add changes to derive mcast_bcast
only if it is a first msdu.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230320090400.30027-1-quic_hprem@quicinc.com
Currently, if we set raw mode as encap type, packets are sent
in native wifi mode which is default mode. This is caused by
no check being present for raw mode in ath12k_dp_tx_get_encap_type
function, so it's always going in native wifi mode.
Fix, this issue by adding check condition for raw mode.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230320052427.12271-1-quic_aarasahu@quicinc.com
Firmware expects physical address in the reo entrance ring when MLO is
enabled and peer meta data in the queue_addr_lo for the non MLO cases.
Current implementation fills the physical address for the non MLO cases
and firmware decodes it differently which leads to SOC CSR region
access which is not related to firmware/MAC operation.
Fix this by sending only peer_meta data and destination indication bit
during non MLO case. This prevents firmware from invalid decoding.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Manish Dharanenthiran <quic_mdharane@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230317162056.20353-1-quic_mdharane@quicinc.com
WMI_CHAN_INFO_DFS flag should be set when configuring a DFS channel
included in scan channel list. Without it, firmware will not send a
probe request frame which is needed in connection to an AP configured
with hidden SSID/network_id. So fix this to allow probe request frames
to be sent in cases where a beacon frame has been seen on the channel
first.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230316041144.7770-1-quic_bqiang@quicinc.com
Currently, during change in bandwidth for peer sta, host sends the
new value of channel width via WMI_PEER_CHWIDTH set peer param command
alone. This can lead to firmware assert in some scenario since before
the command, firmware was having value of channel width and its
corresponding phymode. After the command, host tries to set the new
value of channel width alone which can become incompatible when compared
with its phymode.
For example:
Bandwidth Upgrade
~~~~~~~~~~~~~~~~~~
After association, sta is in 40 MHz bandwidth in 11ax-HE40 phymode.
After bandwidth upgrades, sta moves to 80 MHz but as per phymode,
max bandwidth is still 40 MHz. Hence, firmware assert is seen.
So in this case first phymode should be moved to 11ax-HE80
followed by bandwidth change.
Bandwidth Downgrade
~~~~~~~~~~~~~~~~~~
Similarly, reverse of above is also possible when sta is in 40 MHz
bandwidth in 11ax-HE40 phymode. Bandwidth should be changed to 20 MHz
and if host sends phymode first then, phymode will become 11ax-HE20
and will be incompatible with bandwidth value and hence firmware
assert will be seen. Hence, in this case first channel width
should be set followed by phymode.
Fix this issue by sending WMI set peer param command for phymode as
well as bandwidth based on the type of bandwidth change i.e upgrade
or downgrade.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230315113202.8774-1-quic_aarasahu@quicinc.com
Currently the buffer pointed by event is not freed in case
ATH12K_FLAG_UNREGISTERING bit is set, this causes memory leak.
Add a goto skip instead of return, to ensure event and all the
list entries are freed properly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Rajat Soni <quic_rajson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230315090632.15065-1-quic_rajson@quicinc.com
Perform dma_sync_single_for_cpu() on monitor ring rx buffer before
reading BUFFER_DONE tag and do dma_unmap_single() only after device
had set BUFFER_DONE tag to the buffer.
Also when BUFFER_DONE tag is not set, allow the buffer to get read
next time without freeing skb.
This helps to fix AP+Monitor VAP with flood traffic scenario to see
monitor ring rx buffer overrun missing BUFFER_DONE tag to be set.
Also remove redundant rx dma buf free performed on DP
rx_mon_status_refill_ring.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230309164434.32660-1-quic_hprem@quicinc.com
Currently, in ath11k_ahb_fw_resources_init(), iommu domain
mapping is done only for the chipsets having fixed firmware
memory. Also, for such chipsets, mapping is done only if it
does not have TrustZone support.
During deinitialization, only if TrustZone support is not there,
iommu is unmapped back. However, for non fixed firmware memory
chipsets, TrustZone support is not there and this makes the
condition check to true and it tries to unmap the memory which
was not mapped during initialization.
This leads to the following trace -
[ 83.198790] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000008
[ 83.259537] Modules linked in: ath11k_ahb ath11k qmi_helpers
.. snip ..
[ 83.280286] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 83.287228] pc : __iommu_unmap+0x30/0x140
[ 83.293907] lr : iommu_unmap+0x5c/0xa4
[ 83.298072] sp : ffff80000b3abad0
.. snip ..
[ 83.369175] Call trace:
[ 83.376282] __iommu_unmap+0x30/0x140
[ 83.378541] iommu_unmap+0x5c/0xa4
[ 83.382360] ath11k_ahb_fw_resource_deinit.part.12+0x2c/0xac [ath11k_ahb]
[ 83.385666] ath11k_ahb_free_resources+0x140/0x17c [ath11k_ahb]
[ 83.392521] ath11k_ahb_shutdown+0x34/0x40 [ath11k_ahb]
[ 83.398248] platform_shutdown+0x20/0x2c
[ 83.403455] device_shutdown+0x16c/0x1c4
[ 83.407621] kernel_restart_prepare+0x34/0x3c
[ 83.411529] kernel_restart+0x14/0x74
[ 83.415781] __do_sys_reboot+0x1c4/0x22c
[ 83.419427] __arm64_sys_reboot+0x1c/0x24
[ 83.423420] invoke_syscall+0x44/0xfc
[ 83.427326] el0_svc_common.constprop.3+0xac/0xe8
[ 83.430974] do_el0_svc+0xa0/0xa8
[ 83.435659] el0_svc+0x1c/0x44
[ 83.438957] el0t_64_sync_handler+0x60/0x144
[ 83.441910] el0t_64_sync+0x15c/0x160
[ 83.446343] Code: aa0103f4 f9400001 f90027a1 d2800001 (f94006a0)
[ 83.449903] ---[ end trace 0000000000000000 ]---
This can be reproduced by probing an AHB chipset which is not
having a fixed memory region. During reboot (or rmmod) trace
can be seen.
Fix this issue by adding a condition check on firmware fixed memory
hw_param as done in the counter initialization function.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: f9eec4947a ("ath11k: Add support for targets without trustzone")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230309095308.24937-1-quic_adisi@quicinc.com
The USB device 1668:1200 is Qwest/Actiontec 802AIN which is also
correctly claimed to be supported by carl9170.
Supposedly, the successor 802AIN2 has an ath9k compatible chip
whose USB ID (unknown) could be inserted instead.
Drop the ID from the wrong driver. I happened to find this by chance while
packaging the ath9k and carl9170 firmware for Debian.
Signed-off-by: Bastian Germann <bage@debian.org>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230306125041.2221-1-bage@debian.org
ath.git patches for v6.4. Major changes:
ath10k
* enable threaded napi on WCN3990
ath11k
* push MU-MIMO params from hostapd to hardware
* tx ack signal support for management packets
To support v5 version firmware cycle report, apply the related structure
and functions. v5 cycle report add a group of status to show how the
free-run/TDMA training goes to. It is a firmware mechanism that can auto
adjust coexistence mode between TDMA and free run mechanism at 3 antenna
solution. v5 version provide more reference data to let the mechanism
make decision.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230308053225.24377-8-pkshih@realtek.com
The error map and counter can help to analyze is coexistence mechanism
going well or not. For example, if there is E2G (External control Wi-Fi
slot for Wi-Fi 2.4 GHz) hang counter, it means Wi-Fi firmware didn't cut
a slot for Wi-Fi 2.4 GHz. Maybe something wrong with firmware timer.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230308053225.24377-2-pkshih@realtek.com
The ipw_fw_error structure contains a payload[] flexible array as well as
two pointers to this array area, ->elem, and ->log. The total size of the
allocated structure is computed without use of the <linux/overflow.h>
macros.
There's no reason to keep both a payload[] and an extra pointer to both the
elem and log members. Convert the elem pointer member into the flexible
array member, removing payload.
Fix the allocation of the ipw_fw_error structure to use size_add(),
struct_size(), and array_size() to compute the allocation. This ensures
that any overflow saturates at SIZE_MAX rather than overflowing and
potentially allowing an undersized allocation.
Before the structure change, the layout of ipw_fw_error was:
struct ipw_fw_error {
long unsigned int jiffies; /* 0 8 */
u32 status; /* 8 4 */
u32 config; /* 12 4 */
u32 elem_len; /* 16 4 */
u32 log_len; /* 20 4 */
struct ipw_error_elem * elem; /* 24 8 */
struct ipw_event * log; /* 32 8 */
u8 payload[]; /* 40 0 */
/* size: 40, cachelines: 1, members: 8 */
/* last cacheline: 40 bytes */
};
After this change, the layout is now:
struct ipw_fw_error {
long unsigned int jiffies; /* 0 8 */
u32 status; /* 8 4 */
u32 config; /* 12 4 */
u32 elem_len; /* 16 4 */
u32 log_len; /* 20 4 */
struct ipw_event * log; /* 24 8 */
struct ipw_error_elem elem[]; /* 32 0 */
/* size: 32, cachelines: 1, members: 7 */
/* last cacheline: 32 bytes */
};
This saves a total of 8 bytes for every ipw_fw_error allocation, and
removes the risk of a potential overflow on the allocation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230307230148.3735684-1-jacob.e.keller@intel.com
Many devices ship with a nvram ccode value of X2/XT/XU/XV/ALL which are
all special world-wide compatibility ccode-s. Most of these world-wide
ccode-s allow passive scan mode only for 2.4GHz channels 12-14,
only enabling them when an AP is seen on them.
Since linux-firmware has moved to the new cyfmac4356-pci.bin +
cyfmac4356-pci.clm_blob firmware files this no longer works and
4356 devices using e.g. an X2 ccode fail to connect to an AP on
channel 13.
Add the 4356 chip-id to the list of chips for which to use the ISO3166
country code + rev 0 as fallback in brcmf_translate_country_code() to
fix this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230303222331.285663-1-hdegoede@redhat.com
To clean up drivers/net/wireless move the old drivers drivers left in the
directory to a new "legacy" directory. I did consider adding
CONFIG_WLAN_VENDOR_LEGACY like other vendors have but then dropped the idea as
these are really old drivers and hopefully we get to remove them soon.
There should be no changes in compilation or in Kconfig options, merely moving files.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230227121732.8967-3-kvalo@kernel.org
To clean up drivers/net/wireless move the virtual drivers to a new virtual
directory. I did consider adding CONFIG_WLAN_VENDOR_VIRTUAL like other vendors
have but then dropped the idea as we are not real drivers.
There should be no changes in compilation or in Kconfig options, merely moving
files. The order in menuconfig is slightly changed, the virtual drivers are now
last in the list.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230227121732.8967-2-kvalo@kernel.org
Add some more debug prints in processing regulatory WMI event in order to
increase more debuggability.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-4-quic_adisi@quicinc.com
In order to support different power levels of 6 GHz AP and client,
new WMI event for regulatory - WMI_REG_CHAN_LIST_CC_EXT_EVENTID is
added in firmware. This event provides new parameters required for
6 GHz regulatory rules.
Add support for parsing 2.4 GHz, 5 GHz and 6 GHz reg rules and other
parameters from WMI_REG_CHAN_LIST_CC_EXT_EVENTID.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lavanya Suresh <quic_lavaks@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-3-quic_adisi@quicinc.com
Currently, during regulatory event, 2 GHz/5 GHz is referred
to as 2G/5G including variable names. However, there is no
such entity as 2G or 5G.
Re-name such occurences to its proper name. No functional changes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-2-quic_adisi@quicinc.com
make versioncheck reports the following:
./drivers/net/ethernet/qlogic/qede/qede.h: 10 linux/version.h not needed.
./drivers/net/ethernet/qlogic/qede/qede_ethtool.c: 7 linux/version.h not needed.
So remove linux/version.h from both of these files. Also remove
linux/compiler.h while at it as it is also not being used.
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230309225206.2473644-1-usama.anjum@collabora.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bindings for the am65-cpsw driver use the name "serdes" to refer to
the Serdes PHY. Thus, update the name used for the Serdes PHY within the
am65_cpsw_init_serdes_phy() function from "serdes-phy" to "serdes".
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update bindings to include Serdes PHY as an optional PHY, in addition to
the existing CPSW MAC's PHY. The CPSW MAC's PHY is required while the
Serdes PHY is optional. The Serdes PHY handle has to be provided only
when the Serdes is being configured in a Single-Link protocol. Using the
name "serdes-phy" to represent the Serdes PHY handle, the am65-cpsw-nuss
driver can obtain the Serdes PHY and request the Serdes to be
configured.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
wireless-next patches for 6.4
Major changes:
cfg80211
* 6 GHz improvements
* HW timestamping support
* support for randomized auth/deauth TA for PASN privacy
(also for mac80211)
mac80211
* radiotap TLV and EHT support for the iwlwifi sniffer
* HW timestamping support
* per-link debugfs for multi-link
brcmfmac
* support for Apple (M1 Pro/Max) devices
iwlwifi
* support for a few new devices
* EHT sniffer support
rtw88
* better support for some SDIO devices
(e.g. MAC address from efuse)
rtw89
* HW scan support for 8852b
* better support for 6 GHz scanning
* tag 'wireless-next-2023-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (84 commits)
wifi: iwlwifi: mvm: fix EOF bit reporting
wifi: iwlwifi: Do not include radiotap EHT user info if not needed
wifi: iwlwifi: mvm: add EHT RU allocation to radiotap
wifi: iwlwifi: Update logs for yoyo reset sw changes
wifi: iwlwifi: mvm: clean up duplicated defines
wifi: iwlwifi: rs-fw: break out for unsupported bandwidth
wifi: iwlwifi: Add support for B step of BnJ-Fm4
wifi: iwlwifi: mvm: make flush code a bit clearer
wifi: iwlwifi: mvm: avoid UB shift of snif_queue
wifi: iwlwifi: mvm: add primary 80 known for EHT radiotap
wifi: iwlwifi: mvm: parse FW frame metadata for EHT sniffer mode
wifi: iwlwifi: mvm: decode USIG_B1_B7 RU to nl80211 RU width
wifi: iwlwifi: mvm: rename define to generic name
wifi: iwlwifi: mvm: allow Microsoft to use TAS
wifi: iwlwifi: mvm: add all EHT based on data0 info from HW
wifi: iwlwifi: mvm: add EHT radiotap info based on rate_n_flags
wifi: iwlwifi: mvm: add an helper function radiotap TLVs
wifi: radiotap: separate vendor TLV into header/content
wifi: iwlwifi: reduce verbosity of some logging events
wifi: iwlwifi: Adding the code to get RF name for MsP device
...
====================
Link: https://lore.kernel.org/r/20230310120159.36518-1-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Russell King says:
====================
Rework SFP A2 access conditionals
This series reworks the SFP A2 (diagnostics and control) access so we
don't end up testing a variable number of conditions in several places.
This also resolves a minor issue where we may have a module indicating
that it is not SFF8472 compliant, doesn't implement A2, but fails to
set the enhanced option byte to zero, leading to accesses to the A2
page that fail.
The first patch adds a new flag "have_a2" which indicates whether we
should be accessing the A2 page, and uses this for hwmon. The
conditions are kept the same.
The second patch extends the check for soft-state polling and control
by using this "have_a2" flag (which effectively augments the check to
include some level of SFF8472 compliance.)
====================
Link: https://lore.kernel.org/r/ZAoBnqGBnIZzLwpV@shell.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The soft state bits are stored in the A2h memory space, and require
SFF-8472 compliance. This is what our have_a2 flag tells us, so use
this to indicate whether we should attempt to use the soft signals.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The hwmon code wants to know when it is safe to access the A2h data
stored in a separate address. We indicate that this is present when
we have SFF-8472 compliance and the lack of an address-change
sequence.,
The same conditions are also true if we want to access other controls
and status in the A2h address. So let's make a flag to indicate whether
we can access it, instead of repeating the conditions throughout the
code.
For now, only convert the hwmon code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gal Pressman says:
====================
Couple of minor improvements to build_skb variants
First patch replaces open-coded occurrences of
skb_propagate_pfmemalloc() in build_skb() and build_skb_around().
The secnod patch adds a likely() to the skb allocation in build_skb().
====================
Link: https://lore.kernel.org/r/20230308131720.2103611-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similarly to napi_build_skb(), it is likely the skb allocation in
build_skb() succeeded. frag_size != 0 is also likely, as stated in
__build_skb_around().
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use skb_propagate_pfmemalloc() in build_skb()/build_skb_around() instead
of open-coding it.
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Horatiu Vultur says:
====================
net: lan966x: Add support for IS1 VCAP
Provide the Ingress Stage 1 (IS1) VCAP (Versatile Content-Aware
Processor) support for the Lan966x platform.
The IS1 VCAP has 3 lookups and they are accessible with a TC chain id:
- chain 1000000: IS1 Lookup 0
- chain 1100000: IS1 Lookup 1
- chain 1200000: IS1 Lookup 2
The IS1 is capable of different actions like rewrite VLAN tags, change
priority of the frames, police the traffic, etc. These features will be
added at a later point.
The IS1 currently implements the action that allows setting the value
of a PAG (Policy Association Group) key field in the frame metadata and
this can be used for matching in an IS2 VCAP rule. In this way a rule in
IS0 VCAP can be linked to rules in the IS2 VCAP. The linking is exposed
by using the TC "goto chain" action with an offset from the IS2 chain ids.
For example "goto chain 8000001" will use a PAG value of 1 to chain to a
rule in IS2 lookup 0.
====================
Link: https://lore.kernel.org/r/20230307220929.834219-1-horatiu.vultur@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
