C7x DSP nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with both mboxes and
memory-region information.
As theses only known about at the board integration level, these nodes
should only be enabled when provided with this information.
Disable the C7x DSP nodes in the dtsi files and only enable the ones that
are given the required mboxes and memory-region on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Acked-by: Hari Nagalla <hnagalla@ti.com>
Tested-by: Udit Kumar <u-kumar1@ti.com>
Link: https://lore.kernel.org/r/20230809180145.53158-1-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
TSCADC nodes defined in the top-level AM64 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and/or
device information.
Disable the TSCADC nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-14-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
TSCADC nodes defined in the top-level AM65 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and/or
device information.
Disable the TSCADC nodes in the top-level dtsi files and only enable the
ones that are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-13-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
TSCADC nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and/or
device information.
Disable the TSCADC nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-12-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
GPIO nodes defined in the top-level J7200 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
Disable the GPIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-11-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
GPIO nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
Disable the GPIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-10-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
GPIO nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
Disable the GPIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-9-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
OSPI nodes defined in the top-level AM64 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
As the attached OSPI device is only known about at the board integration
level, these nodes should only be enabled when provided with this
information.
Disable the OSPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-8-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
OSPI nodes defined in the top-level J7200 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
As the attached OSPI device is only known about at the board integration
level, these nodes should only be enabled when provided with this
information.
Disable the OSPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-7-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
OSPI nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
As the attached OSPI device is only known about at the board integration
level, these nodes should only be enabled when provided with this
information.
Disable the OSPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-6-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
OSPI nodes defined in the top-level AM65x SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux and
device information.
As the attached OSPI device is only known about at the board integration
level, these nodes should only be enabled when provided with this
information.
Disable the OSPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-5-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
SDHCI nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and will not be functional unless they are extended.
As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-4-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
SDHCI nodes defined in the top-level J7200 SoC dtsi files are incomplete
and will not be functional unless they are extended.
As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-3-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
SDHCI nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended.
As the attached SD/eMMC is only known about at the board integration level,
these nodes should only be enabled when provided with this information.
Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230810003814.85450-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Add register range of ringacc cfg node to all k3 SoC dtsi files. This is
normally under Device Management firmware control but some entities like
bootloader have to access directly and thus required to be present in DT.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20230809175932.2553156-3-vigneshr@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
RINGACC module on K3 SoCs have CFG register region which is usually
configured by a Device Management firmware. But certain entities such as
bootloader (like U-Boot) may have to access them directly. Describe this
region in the binding documentation for completeness of module
description.
Keep the binding compatible with existing DTS files by requiring first
four regions to be present at least.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230809175932.2553156-2-vigneshr@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
After splitting wkup_pmx pin mux for J784S4 into four regions.
Pin mux offset for ADC nodes were not updated to align with new
regions, due to this while probing ADC driver out of range
error was seen.
Pin mux offsets for ADC nodes are corrected in this patch.
Fixes: 14462bd0b2 ("arm64: dts: ti: k3-j784s4: Fix wakeup pinmux range and pinctrl node offsets")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230809050108.751164-1-u-kumar1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Due to non-addressable regions in J721S2 SOC wkup_pmx was split
into four regions from wkup_pmx0 to wkup_pmx3.
Correcting OSPI1 pin mux, which now falls under wkup_pmx1.
Along with that removing unused pin mux for OSPI-0.
Fixes: 6bc829ceea ("arm64: dts: ti: k3-j721s2: Fix wkup pinmux range")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230804075341.3858488-1-u-kumar1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
After splitting wkup_pmx pin mux for J784S4 into four regions.
Pin mux offset for OSPI nodes were not updated to align with new
regions, due to this while setting ospi pin muxes out of range
error was seen.
Pin mux offsets for OSPI nodes are corrected in this patch.
Fixes: 14462bd0b2 ("arm64: dts: ti: k3-j784s4: Fix wakeup pinmux range and pinctrl node offsets")
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Tested-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20230802114126.162445-1-u-kumar1@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
On AM62ax there are no hardware interrupts routed to A53 GIC
interrupt controller for MCU MCAN IPs, so MCU MCAN nodes were
omitted from MCU dtsi.
Timer polling was introduced in commits [1][2] enabling 3x MCAN
on AM62ax, so now add MCU MCAN nodes to the mcu dtsi for the Cortex A53.
[1] commit b382380c0d ("can: m_can: Add hrtimer to generate software interrupt")
[2] commit bb410c03b9 ("dt-bindings: net: can: Remove interrupt properties for MCAN")
Signed-off-by: Judith Mendez <jm@ti.com>
Link: https://lore.kernel.org/r/20230804220137.425442-1-jm@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
There are two nodes representing the same register space, this looks to
have been created by some merge or copy/paste error. Remove the second
instance of this node and move its children into the first instance.
Signed-off-by: Andrew Davis <afd@ti.com>
Link: https://lore.kernel.org/r/20230802174521.236255-2-afd@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
On AM62x there are no hardware interrupts routed to A53 GIC
interrupt controller for MCU MCAN IPs, so MCU MCAN nodes were
omitted from MCU dtsi.
Timer polling was introduced in commits [1][2] so now add MCU MCAN nodes
to the MCU dtsi for the Cortex A53.
[1] commit b382380c0d ("can: m_can: Add hrtimer to generate software interrupt")
[2] commit bb410c03b9 ("dt-bindings: net: can: Remove interrupt properties for MCAN")
[fd: fixed labels to match datasheet numbering, revised commit message,
fixed reg/reg-names order]
Signed-off-by: Judith Mendez <jm@ti.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20230802073635.11290-2-francesco@dolcini.it
Signed-off-by: Nishanth Menon <nm@ti.com>
The MAIN CPSW2G instance of CPSW on J721S2 SoC can be enabled with the GESI
Expansion Board connected to the J7 Common-Proc-Board. Use the overlay
to enable this.
Add alias for the MAIN CPSW2G port to enable kernel to fetch MAC address
directly from U-Boot.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Link: https://lore.kernel.org/r/20230726065407.378455-3-s-vadapalli@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
CAN instances 3 and 5 in the main domain are brought on the common
processor board through header J27 and J28. The CAN High and Low lines
from the SoC are routed through a mux on the SoM. The select lines need
to be set for the CAN signals to get connected to the transceivers on
the common processor board. Threfore, add respective mux, transceiver
dt nodes to add support for these CAN instances.
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20230725085939.536766-1-b-kapoor@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Only SYSFW has control of SA3UL power.
From SYSFW 08.04.00.002, for security reasons, device ID for power
management of SA3UL has been removed.
"power-domains" property in crypto node tries to access
the SA3UL, for which it gets NACK and hence, SA3UL driver doesn't
probe properly.
Fixes: 8af893654c ("arm64: dts: ti: k3-am62-main: Enable crypto accelerator")
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Link: https://lore.kernel.org/r/20230614-sa3ul-v5-2-29dd2366fba3@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Devices specific to compatible ti,am62-sa3ul don't have control over
power of SA3UL from main domain.
"power-domains" property in crypto node tries to access
the SA3UL power, for which it gets NACK and hence, driver doesn't
probe properly for those particular devices.
Make "power-domains" property as false for devices with
compatible ti,am62-sa3ul.
Fixes: 2ce9a7299b ("dt-bindings: crypto: Add TI SA2UL crypto accelerator documentation")
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Link: https://lore.kernel.org/r/20230614-sa3ul-v5-1-29dd2366fba3@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
The constants to define the idle state of SERDES MUX were defined in
bindings header. They are used only in DTS and driver uses the dt property
to set the idle state making it unsuitable for bindings.
The constants are moved to header next to DTS ("arch/arm64/boot/dts/ti/")
and all the references to bindings header are removed.
So add a warning to mark this bindings header as deprecated.
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20230721125732.122421-3-j-choudhary@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
