dt-bindings: Changes for v7.2-rc1
This adds a compatible string for an upcoming new chip as well as
changes some maintainership information.
* tag 'tegra-for-7.2-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: tegra: pmc: Add Tegra238 compatible
dt-bindings: reserved-memory: Change maintainer for BPMP SHMEM
Signed-off-by: Linus Walleij <linusw@kernel.org>
Gemini device tree updates:
- Add two new devices: the Verbatim Gigabit NAS and the
Raidsonic IB-4210-B, including ACKed binding updates.
- Fix up boot device for the SQ201.
- Use the right LED trigger for disk activity.
- Add the SSP/SPI block to the SoC.
- Fix up the RUT1xx device tree.
* tag 'gemini-for-v7.2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: gemini: Correct the RUT1xx
ARM: dts: Add a Raidsonic IB-4210-B DTS
ARM: dts: Add a Verbatim Gigabit NAS DTS
dt-bindings: arm: Add two missing Gemini devices
dt-bindings: vendor-prefixes: Add Verbatim Corporation
ARM: dts: gemini: Add SSP/SPI block
ARM: dts: gemini: Tag disk led for disk-activity
ARM: dts: gemini: iTian SQ201 need to boot from mtdblock3
Signed-off-by: Linus Walleij <linusw@kernel.org>
New peripherals: Watchdog on RK3528, MIPI CSI-2 receiver on RK3588.
Adding frl-enable-gpios to a number of boards for HDMI 2.0 support.
And a bunch of fixes and new peripherals for a number of boards.
* tag 'v7.2-rockchip-dts64-1' of https://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (30 commits)
arm64: dts: rockchip: Add watchdog node for RK3528
arm64: dts: rockchip: add mipi csi-2 receiver nodes to rk3588
arm64: dts: rockchip: fix rk809 interrupt pin on rk3566-roc-pc
arm64: dts: rockchip: Add missing pinctrl-names to rk3588s boards
arm64: dts: rockchip: Add missing pinctrl-names to rk3588 boards
arm64: dts: rockchip: Add missing pinctrl-names to rk3576 boards
arm64: dts: rockchip: Drop unnecessary #{address,size}-cells from rk3588-jaguar
arm64: dts: rockchip: Add frl-enable-gpios to rk3588s-roc-pc
arm64: dts: rockchip: Add frl-enable-gpios to rk3588s-orangepi-cm5-base
arm64: dts: rockchip: Add frl-enable-gpios to rk3588s-khadas-edge2
arm64: dts: rockchip: Add frl-enable-gpios to rk3588s-gameforce-ace
arm64: dts: rockchip: Add frl-enable-gpios to rk3588s boards
arm64: dts: rockchip: Add frl-enable-gpios to rk3588 boards
arm64: dts: rockchip: Add frl-enable-gpios to rk3576-nanopi-r76s
arm64: dts: rockchip: Add frl-enable-gpios to rk3576-luckfox-core3576
arm64: dts: rockchip: Add frl-enable-gpios to rk3576 boards
arm64: dts: rockchip: Add AP6275P wireless support for Khadas Edge 2L
arm64: dts: rockchip: Add HYM8563 RTC for Khadas Edge 2L
arm64: dts: rockchip: Add #{address,size}-cells to Chromium-based /firmware
arm64: dts: rockchip: Add HDMI and VOP support for Khadas Edge 2L
...
Signed-off-by: Linus Walleij <linusw@kernel.org>
Qualcomm Arm64 DeviceTree updates for v7.2
Introduce the Qualcomm IPQ9650 router/gateway platform and the RDP488
board. Add support for the Motorola Edge 30 and the Nothing Phone.
Describe the IPA block on the Agatti platform and missing OPP-levels for
the video encoder/decoder.
For Eliza, describe the QUP Serial Engines, GPI DMA, SDHCI, LLCC, IMEM,
QCE crypto, ADSP remoteproc and USB nodes. Enable DSI panel,
DisplayPort, USB, and ADSP support on the Eliza MTP.
On Glymur enable ADSP and CDSP remoteprocs, FastRPC, crypto hardware,
CPUfreq cooling devices, and coresight nodes. Enable the remoteprocs and
the LID sensor on the Glymur CRD.
Describe the CAN-FD controller found on the Hamoa EVK. Correct the
DisplayPort controller OPP tables.
Describe the watchdog on IPQ5210 and IPQ9650.
Describe USB controller and PHYs for the Kaanapali platform and enable
basic USB support on the MTP and QRD devices.
Enable the second display subsystem on Lemans and use this to enable
additional DisplayPort outputs on the Lemans Ride board, and IFP
mezzanine for the EVK. Also enable the GPIO expander on the Lemans EVK
to get the CAN signals out.
Add crypto hardware and qfprom nodes on Milos. Reduce the remotefs
shared memory size to avoid sanity checks in the modem firmware
rejecting the region.
Enable the vibrator on FairPhone FP6.
Add GPSDP FastRPC support on Monaco, and describe the Bluetooth
controller on the Arduino VENTUNO Q board.
Introduce an EL2 overlay for the Purwa IoT EVK.
Enable CAN bus controller on QCS6490 RB3gen2 and add a remotefs node.
Enable FastRPC on the SC8280XP ADSP.
Correct SDM630 and SDM660 ADSP FastRPC channel ids. Also add the ADSP
memory region on SDM630.
On SDM845 devices, enable NFC on Google Pixel 3, OnePlus 6, OnePlus 6T,
and SHIFT SHIFT6mq. Enable camera flash on LG devices. Rework the
framebuffer description on Samsung, SHIFT and Xiaomi devices. Enable
camera flash on LG devices. Fix Bluetooth and WiFi on LG and Xiaomi
devices.
Enable MDSS and the display panel on Xiaomi Mi A3.
Scale L3 and DDR clock votes based on CPUfreq selection.
Enable camera clock controller, cpufreq cooling devices, and correct the
DSI1 reference clock on SM8750.
On the Talos platform, describe the QSPI support, GPR and audio
services, and enable sound on the EVK target. Enable QSPI and describe
the SPINOR on this bus, on the QCS615 Ride.
Describe power-domain and iface clock for the Inline Crypto Engine (ICE)
across various platforms.
Fix the Bluetooth RFA supply name across a variety of devices.
* tag 'qcom-arm64-for-7.2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (131 commits)
arm64: dts: qcom: add support for pixel 3a xl with the tianma panel
arm64: dts: qcom: sdm670-google: add common device tree include
arm64: dts: qcom: hamoa-iot-evk: add MCP2518FD CAN on spi18
arm64: dts: qcom: sm8750: allow mode-switch events to reach the QMP Combo PHY
arm64: dts: qcom: sc8280xp: drop unused polling-delay-passive properties
arm64: dts: qcom: ipq5210: add watchdog node
arm64: dts: qcom: sdm845-xiaomi-beryllium: Correct IPA FW path
arm64: dts: qcom: monaco-arduino-monza: Add Bluetooth UART node
arm64: dts: qcom: glymur: Add qfprom efuse node
arm64: dts: qcom: milos: Add qfprom efuse node
arm64: dts: qcom: glymur: add coresight nodes
arm64: dts: qcom: qcs6490-rb3gen2: add rmtfs node
arm64: dts: qcom: lemans-evk: Enable CAN RX via I2C GPIO expander
arm64: dts: qcom: glymur: Fix wrong interrupt number for i2c19
arm64: dts: qcom: Drop unused remoteproc_adsp_glink label
arm64: dts: qcom: lemans: Add eDP ref clock for eDP PHYs
arm64: dts: qcom: sm8750: Add power-domain and iface clk for ice node
arm64: dts: qcom: sm8650: Add power-domain and iface clk for ice node
arm64: dts: qcom: sm8550: Add power-domain and iface clk for ice node
arm64: dts: qcom: sm8450: Add power-domain and iface clk for ice node
...
Signed-off-by: Linus Walleij <linusw@kernel.org>
- Add cpuidle and cpufreq support for Sky1
* tag 'cix-dt-v7.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/cix:
arm64: dts: cix: Add CPU idle states for Sky1
arm64: dts: cix: Add SCMI performance domains for CPUFreq on Sky1
Signed-off-by: Linus Walleij <linusw@kernel.org>
The PMC found on Tegra238 is similar to the version in earlier chips but
some of the register offsets and bitfields differ, so add a specific
compatible string for this new variant.
Signed-off-by: Prathamesh Shete <pshete@nvidia.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix two problems with the RUT1xx device tree:
- The memory is 32MB not 128MB
- The console is 19200 BPS
- Activate the PCI
- Disable the unused USB ports
Signed-off-by: Linus Walleij <linusw@kernel.org>
This adds a device tree for the Raidsonic IB-4210-B NAS, a slightly
under-powered version of IB-4220-B with half the memory and
the cheaper version of the SoC.
Signed-off-by: Linus Walleij <linusw@kernel.org>
This adds a device tree for the Verbatim S08V1901-D1 NAS
which also has the product names "Gigabit Network Hard Drive"
"Gigabit NAS" and maybe other names.
Signed-off-by: Linus Walleij <linusw@kernel.org>
This adds the Raidsonic IB-4210-B and the Verbatim
S08V1901-D1 that were missing from the bindings.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Linus Walleij <linusw@kernel.org>
Linux now has a trigger specifically for all disk activity
and this is what the LED is used for so tag it like such.
Signed-off-by: Linus Walleij <linusw@kernel.org>
The Pixel 3a XL can be supported by reusing most of the device tree from
the Pixel 3a. Move the common elements to a common device tree include
like with other devices.
Since the original devicetree should only specify non-XL properties, it
needs to be completely rewritten. Also change the SPDX license
identifier from GPL-2.0 (which was deprecated as it can be
misinterpreted as GPLv2 or later) into GPL-2.0-only.
Signed-off-by: Richard Acayan <mailingradian@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Assisted-by: "Claude Code Review Bot":claude-opus-4-6
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260513172549.1345-2-mailingradian@gmail.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The QCA2066 Bluetooth chip is powered by a board-level 3.3 V supply
provided by the hardware. This change connects the Bluetooth
controller via UART10, and the corresponding GPIO is used to enable
the Bluetooth chip.
basic function test step:
- bluetoothctl power on/off
- bluetoothctl scan bredr/le
- bluetoothctl pair <remote device address>
- bluetoothctl connect <remote device address>
low-state test and state:
- rtcwake -d /dev/rtc0 -m no -s 30 && systemctl suspend
cat /sys/kernel/debug/suspend_stats
success: 1
fail: 0
failed_freeze: 0
failed_prepare: 0
failed_suspend: 0
failed_suspend_late: 0
failed_suspend_noirq: 0
failed_resume: 0
failed_resume_early: 0
failed_resume_noirq: 0
failures:
last_failed_dev:
last_failed_errno: 0
0
last_failed_step:
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260429103537.1282497-1-shuai.zhang@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Add the qfprom efuse node and describe where the GPU speedbin fuse is
located on Milos.
Note that for SM7635-AB at least, the value is "221", the max frequency
for this is 1050MHz. There's another speedbin out there for 1150MHz but
we do not know the value for it so just document in this commit.
Once the value is discovered we should add the speedbins to the A810
Adreno entry and update devicetree.
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260331-milos-qfprom-v1-2-36017cc642db@pm.me
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The LeMans EVK board routes the RX lines of CAN controllers 2, 4, and 6
(part of the RTSS subsystem) through a signal multiplexer controlled by
GPIO 4 of the I2C GPIO expander at address 0x3b. The remaining CAN
controllers, out of 8 total on RTSS, are wired directly to their
transceivers.
The multiplexer select pin defaults low on reset, disconnecting CAN 2,
4, and 6 RX lines from their respective transceivers, which results in
no data being received on these interfaces.
Configure GPIO 4 as output-high to assert the mux select line at boot,
connecting the RX signals of CAN 2, 4, and 6 to their transceivers as
required by the EVK board wiring.
Signed-off-by: Anup Kulkarni <anup.kulkarni@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260519064954.2759960-1-anup.kulkarni@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
The eDP PHY nodes on lemans were missing the reference clock voting.
This initially went unnoticed because the clock was implicitly enabled
by the UFS PHY driver, and the eDP PHY happened to rely on that.
After commit 77d2fa54a9 ("scsi: ufs: qcom : Refactor phy_power_on/off
calls"), the UFS driver no longer keeps the reference clock enabled.
As a result, the eDP PHY fails to power on.
To fix this, add eDP reference clock for eDP PHYs on lemans chipset
ensuring reference clock is enabled.
Fixes: e1e3e5673f ("arm64: dts: qcom: sa8775p: add DisplayPort device nodes")
Signed-off-by: Ritesh Kumar <quic_riteshk@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260128114853.2543416-3-quic_riteshk@quicinc.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Merge the two fixes for ICC blocks in Milos and Eliza through a topic
branch, in order to resolve the introduced DT validation errors in
v7.1-rc while avoiding the merge conflicts against arm64-for-7.2.
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
for its own resources. Before accessing ICE hardware during probe, to
avoid potential unclocked register access issues (when clk_ignore_unused
is not passed on the kernel command line), in addition to the 'core' clock
the 'iface' clock should also be turned on by the driver. This can only be
done if the GCC_UFS_PHY_GDSC power domain is enabled. Specify both the
GCC_UFS_PHY_GDSC power domain and the 'iface' clock in the ICE node for
sm8750.
Fixes: b1dac789c6 ("arm64: dts: qcom: sm8750: Add ICE nodes")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-11-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
for its own resources. Before accessing ICE hardware during probe, to
avoid potential unclocked register access issues (when clk_ignore_unused
is not passed on the kernel command line), in addition to the 'core' clock
the 'iface' clock should also be turned on by the driver. This can only be
done if the UFS_PHY_GDSC power domain is enabled. Specify both the
UFS_PHY_GDSC power domain and the 'iface' clock in the ICE node for sm8650.
Fixes: 10e0246712 ("arm64: dts: qcom: sm8650: add interconnect dependent device nodes")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-10-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
for its own resources. Before accessing ICE hardware during probe, to
avoid potential unclocked register access issues (when clk_ignore_unused
is not passed on the kernel command line), in addition to the 'core' clock
the 'iface' clock should also be turned on by the driver. This can only be
done if the UFS_PHY_GDSC power domain is enabled. Specify both the
UFS_PHY_GDSC power domain and the 'iface' clock in the ICE node for sm8550.
Fixes: b8630c48b4 ("arm64: dts: qcom: sm8550: Add the Inline Crypto Engine node")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-9-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
for its own resources. Before accessing ICE hardware during probe, to
avoid potential unclocked register access issues (when clk_ignore_unused
is not passed on the kernel command line), in addition to the 'core' clock
the 'iface' clock should also be turned on by the driver. This can only be
done if the UFS_PHY_GDSC power domain is enabled. Specify both the
UFS_PHY_GDSC power domain and the 'iface' clock in the ICE node for sm8450.
Fixes: 86b0aef435 ("arm64: dts: qcom: sm8450: Use standalone ICE node for UFS")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-8-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
for its own resources. Before accessing ICE hardware during probe, to
avoid potential unclocked register access issues (when clk_ignore_unused
is not passed on the kernel command line), in addition to the 'core' clock
the 'iface' clock should also be turned on by the driver. This can only be
done if the GCC_UFS_PHY_GDSC power domain is enabled. Specify both the
GCC_UFS_PHY_GDSC power domain and the 'iface' clock in the ICE node for
kodiak.
Fixes: dfd5ee7b34 ("arm64: dts: qcom: sc7280: Add inline crypto engine")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Tested-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-7-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
for its own resources. Before accessing ICE hardware during probe, to
avoid potential unclocked register access issues (when clk_ignore_unused
is not passed on the kernel command line), in addition to the 'core' clock
the 'iface' clock should also be turned on by the driver. This can only be
done if the UFS_PHY_GDSC power domain is enabled. Specify both the
UFS_PHY_GDSC power domain and the 'iface' clock in the ICE node for sc7180.
Fixes: 858536d9dc ("arm64: dts: qcom: sc7180: Add UFS nodes")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-6-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
for its own resources. Before accessing ICE hardware during probe, to
avoid potential unclocked register access issues (when clk_ignore_unused
is not passed on the kernel command line), in addition to the 'core' clock
the 'iface' clock should also be turned on by the driver. This can only be
done if the GCC_UFS_PHY_GDSC power domain is enabled. Specify both the
GCC_UFS_PHY_GDSC power domain and the 'iface' clock in the ICE node for
monaco.
Fixes: cc9d29aad8 ("arm64: dts: qcom: qcs8300: enable the inline crypto engine")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-5-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
for its own resources. Before accessing ICE hardware during probe, to
avoid potential unclocked register access issues (when clk_ignore_unused
is not passed on the kernel command line), in addition to the 'core' clock
the 'iface' clock should also be turned on by the driver. This can only be
done if the GCC_UFS_PHY_GDSC power domain is enabled. Specify both the
GCC_UFS_PHY_GDSC power domain and the 'iface' clock in the ICE node for
kaanapali.
Fixes: 2eeb5767d5 ("arm64: dts: qcom: Introduce Kaanapali SoC")
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-3-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
for its own resources. Before accessing ICE hardware during probe, to
avoid potential unclocked register access issues (when clk_ignore_unused
is not passed on the kernel command line), in addition to the 'core' clock
the 'iface' clock should also be turned on by the driver. This can only be
done if the GCC_UFS_PHY_GDSC power domain is enabled. Specify both the
GCC_UFS_PHY_GDSC power domain and the 'iface' clock in the ICE node for
eliza.
Fixes: af20af39fc ("arm64: dts: qcom: Introduce Eliza Soc base dtsi")
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Fixes: 54a4f0239f ("KVM: MMU: make kvm_mmu_zap_page() return the
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-13-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Qualcomm in-line crypto engine (ICE) platform driver specifies and votes
for its own resources. Before accessing ICE hardware during probe, to
avoid potential unclocked register access issues (when clk_ignore_unused
is not passed on the kernel command line), in addition to the 'core' clock
the 'iface' clock should also be turned on by the driver. This can only be
done if the UFS_PHY_GDSC power domain is enabled. Specify both the
UFS_PHY_GDSC power domain and the 'iface' clock in the ICE node for milos.
Fixes: 04bb374333 ("arm64: dts: qcom: milos: Add UFS nodes")
Signed-off-by: Harshal Dev <harshal.dev@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Kuldeep Singh <kuldeep.singh@oss.qualcomm.com>
Link: https://lore.kernel.org/r/20260416-qcom_ice_power_and_clk_vote-v5-12-5ccf5d7e2846@oss.qualcomm.com
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
