If this quirk was set then driver would treat transfer events with
'Success' completion code as 'Short packet' if there were untransferred
bytes left.
This is so common that turn it into default behavior.
xhci_warn_ratelimited() is no longer used after this, so remove it.
A success event with untransferred bytes left doesn't always mean a
misbehaving controller. If there was an error mid a multi-TRB TD it's
allowed to issue a success event for the last TRB in that TD.
See xhci 1.2 spec 4.9.1 Transfer Descriptors
"Note: If an error is detected while processing a multi-TRB TD, the xHC
shall generate a Transfer Event for the TRB that the error was detected
on with the appropriate error Condition Code, then may advance to the
next TD. If in the process of advancing to the next TD, a Transfer TRB
is encountered with its IOC flag set, then the Condition Code of the
Transfer Event generated for that Transfer TRB should be Success,
because there was no error actually associated with the TRB that
generated the Event. However, an xHC implementation may redundantly
assert the original error Condition Code."
Co-developed-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the number of do-while loops by 1. The number of loops should be
number of segment + 1, the +1 is in case deq and enq are on the same
segment. But due to the use of a do-while loop, the expression is
evaluated after executing the loop, thus the loop is executed 1 extra
time.
Changing the do-while loop expression from "<=" to "<", reduces the loop
amount by 1. The expression "<=" would also work if it was a while loop
instead of a do-while loop.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Address debug message inaccuracies in xhci_ring_expansion_needed().
Specifically, remove the portion of the debug message that indicates the
number of enqueue TRBs to be added to the dequeue segment. This part of
the message may mislead and the calculated value is incorrect. Given that
this value is not of significant importance and the statement is not
consistently accurate, it has been omitted.
The specific issues with the debug message that this commit resolves:
- The calculation of the number of TRBs is incorrect. The current
calculation erroneously includes the link TRB, which is reserved.
Furthermore, the calculated number of TRBs can exceed the dequeue
segment, resulting in a misleading debug message.
- The current phrasing suggests that "ring expansion by X is needed,
adding X TRBs moves enqueue Y TRBs into the dequeue segment".
The intended message, however, is "IF the ring is NOT expanded by X,
THEN adding X TRBs moves enqueue Y TRBs into the dequeue segment".
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check if requested segments ('segs' or 'ERST_DEFAULT_SEGS') exceeds the
maximum amount ERST supports.
When 'segs' is '0', 'ERST_DEFAULT_SEGS' is used instead. But both values
may not exceed ERST max.
Macro 'ERST_MAX_SEGS' is renamed to 'ERST_DEFAULT_SEGS'. The new name
better represents the macros, which is the number of Event Ring segments
to allocate, when the amount is not specified.
Additionally, rename and change xhci_create_secondary_interrupter()'s
argument 'int num_segs' to 'unsigned int segs'. This makes it the same
as its counter part in xhci_alloc_interrupter().
Fixes: c99b38c412 ("xhci: add support to allocate several interrupters")
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port capability flags for USB2 ports have been cached in an
u32 xhci->ext_caps[] array long before the driver had struct xhci_port
and struct xhci_port_cap structures.
Move these cached USB2 port capability values together with the other
port capability values into struct xhci_port_cap cability structure.
This also gets rid of the cumbersome way of mapping port to USB2
capability based on portnum as each port has a pointer to its capability
structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240429140245.3955523-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the compatible string for SC8280 Multiport USB controller from
Qualcomm.
There are 4 power event interrupts supported by this controller
(one for each port of multiport controller). Add all the 4 as
non-optional interrupts for SC8280XP-MP
Also each port of multiport has one DP and one DM IRQ. Add all DP/DM
IRQs related to 4 ports of SC8280XP Teritiary controller.
Also added SuperSpeed PHY interrupt for both Superspeed ports.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-6-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the DWC3 driver supports only single port controller
which requires at least one HS PHY and at most one SS PHY.
But the DWC3 USB controller can be connected to multiple ports and
each port can have their own PHYs. Each port of the multiport
controller can either be HS+SS capable or HS only capable
Proper quantification of them is required to modify GUSB2PHYCFG
and GUSB3PIPECTL registers appropriately.
DWC3 multiport controllers are capable to service at most 15 High Speed
PHYs and 4 Supser Speed PHYs. Add support for detecting, obtaining and
configuring PHYs supported by a multiport controller.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-5-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All DWC3 Multi Port controllers that exist today only support host mode.
Temporarily map XHCI address space for host-only controllers and parse
XHCI Extended Capabilities registers to read number of usb2 ports and
usb3 ports present on multiport controller. Each USB Port is at least HS
capable.
The port info for usb2 and usb3 phy are identified as num_usb2_ports
and num_usb3_ports and these are used as iterators for phy operations
and for modifying GUSB2PHYCFG/ GUSB3PIPECTL registers accordingly.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Bjorn Andersson <quic_bjorande@quicinc.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240420044901.884098-3-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull char / misc driver fixes from Greg KH:
"Here are some small char/misc and other driver fixes for 6.9-rc5.
Included in here are the following:
- binder driver fix for reported problem
- speakup crash fix
- mei driver fixes for reported problems
- comdei driver fix
- interconnect driver fixes
- rtsx driver fix
- peci.h kernel doc fix
All of these have been in linux-next for over a week with no reported
problems"
* tag 'char-misc-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
peci: linux/peci.h: fix Excess kernel-doc description warning
binder: check offset alignment in binder_get_object()
comedi: vmk80xx: fix incomplete endpoint checking
mei: vsc: Unregister interrupt handler for system suspend
Revert "mei: vsc: Call wake_up() in the threaded IRQ handler"
misc: rtsx: Fix rts5264 driver status incorrect when card removed
mei: me: disable RPL-S on SPS and IGN firmwares
speakup: Avoid crash on very long word
interconnect: Don't access req_list while it's being manipulated
interconnect: qcom: x1e80100: Remove inexistent ACV_PERF BCM
Pull kernfs bugfix and documentation update from Greg KH:
"Here are two changes for 6.9-rc5 that deal with "driver core" stuff,
that do the following:
- sysfs reference leak fix
- embargoed-hardware-issues.rst update for Power
Both of these have been in linux-next for over a week with no reported
issues"
* tag 'driver-core-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation: embargoed-hardware-issues.rst: Add myself for Power
fs: sysfs: Fix reference leak in sysfs_break_active_protection()
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty and serial driver fixes for 6.9-rc5 that
resolve a bunch of reported problems. Included in here are:
- MAINTAINERS and .mailmap update for Richard Genoud
- serial core regression fixes from 6.9-rc1 changes
- pci id cleanups
- serial core crash fix
- stm32 driver fixes
- 8250 driver fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: stm32: Reset .throttled state in .startup()
serial: stm32: Return IRQ_NONE in the ISR if no handling happend
serial: core: Fix missing shutdown and startup for serial base port
serial: core: Clearing the circular buffer before NULLifying it
MAINTAINERS: mailmap: update Richard Genoud's email address
serial/pmac_zilog: Remove flawed mitigation for rx irq flood
serial: 8250_pci: Remove redundant PCI IDs
serial: core: Fix regression when runtime PM is not enabled
serial: mxs-auart: add spinlock around changing cts state
serial: 8250_dw: Revert: Do not reclock if already at correct rate
serial: 8250_lpc18xx: disable clks on error in probe()
Pull USB / Thunderbolt driver fixes from Greg KH:
"Here are some small USB and Thunderbolt driver fixes for 6.9-rc5.
Included in here are:
- MAINTAINER file update for invalid email address
- usb-serial device id updates
- typec driver fixes
- thunderbolt / usb4 driver fixes
- usb core shutdown fixes
- cdc-wdm driver revert for reported problem in -rc1
- usb gadget driver fixes
- xhci driver fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'usb-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: serial: option: add Telit FN920C04 rmnet compositions
usb: dwc3: ep0: Don't reset resource alloc flag
Revert "usb: cdc-wdm: close race between read and workqueue"
USB: serial: option: add Rolling RW101-GL and RW135-GL support
USB: serial: option: add Lonsung U8300/U9300 product
USB: serial: option: add support for Fibocom FM650/FG650
USB: serial: option: support Quectel EM060K sub-models
USB: serial: option: add Fibocom FM135-GL variants
usb: misc: onboard_usb_hub: Disable the USB hub clock on failure
thunderbolt: Avoid notify PM core about runtime PM resume
thunderbolt: Fix wake configurations after device unplug
usb: dwc2: host: Fix dereference issue in DDMA completion flow.
usb: typec: mux: it5205: Fix ChipID value typo
MAINTAINERS: Drop Li Yang as their email address stopped working
usb: gadget: fsl: Initialize udc before using it
usb: Disable USB3 LPM at shutdown
usb: gadget: f_ncm: Fix UAF ncm object at re-bind after usb ep transport error
usb: typec: tcpm: Correct the PDO counting in pd_set
usb: gadget: functionfs: Wait for fences before enqueueing DMABUF
usb: gadget: functionfs: Fix inverted DMA fence direction
...
Pull scheduler fix from Borislav Petkov:
- Add a missing memory barrier in the concurrency ID mm switching
* tag 'sched_urgent_for_v6.9_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Add missing memory barrier in switch_mm_cid
Pull x86 fixes from Borislav Petkov:
- Fix CPU feature dependencies of GFNI, VAES, and VPCLMULQDQ
- Print the correct error code when FRED reports a bad event type
- Add a FRED-specific INT80 handler without the special dances that
need to happen in the current one
- Enable the using-the-default-return-thunk-but-you-should-not warning
only on configs which actually enable those special return thunks
- Check the proper feature flags when selecting BHI retpoline
mitigation
* tag 'x86_urgent_for_v6.9_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpufeatures: Fix dependencies for GFNI, VAES, and VPCLMULQDQ
x86/fred: Fix incorrect error code printout in fred_bad_type()
x86/fred: Fix INT80 emulation for FRED
x86/retpolines: Enable the default thunk warning only on relevant configs
x86/bugs: Fix BHI retpoline check
Pull block fixes from Jens Axboe:
"Just two minor fixes that should go into the 6.9 kernel release, one
fixing a regression with partition scanning errors, and one fixing a
WARN_ON() that can get triggered if we race with a timer"
* tag 'block-6.9-20240420' of git://git.kernel.dk/linux:
blk-iocost: do not WARN if iocg was already offlined
block: propagate partition scanning errors to the BLKRRPART ioctl
Pull email address update from James Bottomley:
"My IBM email has stopped working, so update to a working email
address"
* tag 'email' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
MAINTAINERS: update to working email address
Pull kvm fixes from Paolo Bonzini:
"This is a bit on the large side, mostly due to two changes:
- Changes to disable some broken PMU virtualization (see below for
details under "x86 PMU")
- Clean up SVM's enter/exit assembly code so that it can be compiled
without OBJECT_FILES_NON_STANDARD. This fixes a warning "Unpatched
return thunk in use. This should not happen!" when running KVM
selftests.
Everything else is small bugfixes and selftest changes:
- Fix a mostly benign bug in the gfn_to_pfn_cache infrastructure
where KVM would allow userspace to refresh the cache with a bogus
GPA. The bug has existed for quite some time, but was exposed by a
new sanity check added in 6.9 (to ensure a cache is either
GPA-based or HVA-based).
- Drop an unused param from gfn_to_pfn_cache_invalidate_start() that
got left behind during a 6.9 cleanup.
- Fix a math goof in x86's hugepage logic for
KVM_SET_MEMORY_ATTRIBUTES that results in an array overflow
(detected by KASAN).
- Fix a bug where KVM incorrectly clears root_role.direct when
userspace sets guest CPUID.
- Fix a dirty logging bug in the where KVM fails to write-protect
SPTEs used by a nested guest, if KVM is using Page-Modification
Logging and the nested hypervisor is NOT using EPT.
x86 PMU:
- Drop support for virtualizing adaptive PEBS, as KVM's
implementation is architecturally broken without an obvious/easy
path forward, and because exposing adaptive PEBS can leak host LBRs
to the guest, i.e. can leak host kernel addresses to the guest.
- Set the enable bits for general purpose counters in
PERF_GLOBAL_CTRL at RESET time, as done by both Intel and AMD
processors.
- Disable LBR virtualization on CPUs that don't support LBR
callstacks, as KVM unconditionally uses
PERF_SAMPLE_BRANCH_CALL_STACK when creating the perf event, and
would fail on such CPUs.
Tests:
- Fix a flaw in the max_guest_memory selftest that results in it
exhausting the supply of ucall structures when run with more than
256 vCPUs.
- Mark KVM_MEM_READONLY as supported for RISC-V in
set_memory_region_test"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (30 commits)
KVM: Drop unused @may_block param from gfn_to_pfn_cache_invalidate_start()
KVM: selftests: Add coverage of EPT-disabled to vmx_dirty_log_test
KVM: x86/mmu: Fix and clarify comments about clearing D-bit vs. write-protecting
KVM: x86/mmu: Remove function comments above clear_dirty_{gfn_range,pt_masked}()
KVM: x86/mmu: Write-protect L2 SPTEs in TDP MMU when clearing dirty status
KVM: x86/mmu: Precisely invalidate MMU root_role during CPUID update
KVM: VMX: Disable LBR virtualization if the CPU doesn't support LBR callstacks
perf/x86/intel: Expose existence of callback support to KVM
KVM: VMX: Snapshot LBR capabilities during module initialization
KVM: x86/pmu: Do not mask LVTPC when handling a PMI on AMD platforms
KVM: x86: Snapshot if a vCPU's vendor model is AMD vs. Intel compatible
KVM: x86: Stop compiling vmenter.S with OBJECT_FILES_NON_STANDARD
KVM: SVM: Create a stack frame in __svm_sev_es_vcpu_run()
KVM: SVM: Save/restore args across SEV-ES VMRUN via host save area
KVM: SVM: Save/restore non-volatile GPRs in SEV-ES VMRUN via host save area
KVM: SVM: Clobber RAX instead of RBX when discarding spec_ctrl_intercepted
KVM: SVM: Drop 32-bit "support" from __svm_sev_es_vcpu_run()
KVM: SVM: Wrap __svm_sev_es_vcpu_run() with #ifdef CONFIG_KVM_AMD_SEV
KVM: SVM: Create a stack frame in __svm_vcpu_run() for unwinding
KVM: SVM: Remove a useless zeroing of allocated memory
...
Pull powerpc fixes from Michael Ellerman:
- Fix wireguard loading failure on pre-Power10 due to Power10 crypto
routines
- Fix papr-vpd selftest failure due to missing variable initialization
- Avoid unnecessary get/put in spapr_tce_platform_iommu_attach_dev()
Thanks to Geetika Moolchandani, Jason Gunthorpe, Michal Suchánek, Nathan
Lynch, and Shivaprasad G Bhat.
* tag 'powerpc-6.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
selftests/powerpc/papr-vpd: Fix missing variable initialization
powerpc/crypto/chacha-p10: Fix failure on non Power10
powerpc/iommu: Refactor spapr_tce_platform_iommu_attach_dev()
Pull clk fixes from Stephen Boyd:
"A couple clk driver fixes, a build fix, and a deadlock fix:
- Mediatek mt7988 has broken PCIe because the wrong parent is used
- Mediatek clk drivers may deadlock when registering their clks
because the clk provider device is repeatedly runtime PM resumed
and suspended during probe and clk registration.
Resuming the clk provider device deadlocks with an ABBA deadlock
due to genpd_lock and the clk prepare_lock. The fix is to keep the
device runtime resumed while registering clks.
- Another runtime PM related deadlock, this time with disabling
unused clks during late init.
We get an ABBA deadlock where a device is runtime PM resuming (or
suspending) while the disabling of unused clks is happening in
parallel. That runtime PM action calls into the clk framework and
tries to grab the clk prepare_lock while the disabling of unused
clks holds the prepare_lock and is waiting for that runtime PM
action to complete.
The fix is to runtime resume all the clk provider devices before
grabbing the clk prepare_lock during disable unused.
- A build fix to provide an empty devm_clk_rate_exclusive_get()
function when CONFIG_COMMON_CLK=n"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: mediatek: mt7988-infracfg: fix clocks for 2nd PCIe port
clk: mediatek: Do a runtime PM get on controllers during probe
clk: Get runtime PM before walking tree for clk_summary
clk: Get runtime PM before walking tree during disable_unused
clk: Initialize struct clk_core kref earlier
clk: Don't hold prepare_lock when calling kref_put()
clk: Remove prepare_lock hold assertion in __clk_release()
clk: Provide !COMMON_CLK dummy for devm_clk_rate_exclusive_get()
Pull perf tools fixes from Namhyung Kim:
"A random set of small bug fixes:
- Fix perf annotate TUI when used with data type profiling
- Work around BPF verifier about sighand lock checking
And a set of kernel header synchronization"
* tag 'perf-tools-fixes-for-v6.9-2024-04-19' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
tools/include: Sync arm64 asm/cputype.h with the kernel sources
tools/include: Sync asm-generic/bitops/fls.h with the kernel sources
tools/include: Sync x86 asm/msr-index.h with the kernel sources
tools/include: Sync x86 asm/irq_vectors.h with the kernel sources
tools/include: Sync x86 CPU feature headers with the kernel sources
tools/include: Sync uapi/sound/asound.h with the kernel sources
tools/include: Sync uapi/linux/kvm.h and asm/kvm.h with the kernel sources
tools/include: Sync uapi/linux/fs.h with the kernel sources
tools/include: Sync uapi/drm/i915_drm.h with the kernel sources
perf lock contention: Add a missing NULL check
perf annotate: Make sure to call symbol__annotate2() in TUI
Pull iommufd fixes from Jason Gunthorpe:
"Two fixes for the selftests:
- CONFIG_IOMMUFD_TEST needs CONFIG_IOMMUFD_DRIVER to work
- The kconfig fragment sshould include fault injection so the fault
injection test can work"
* tag 'for-linus-iommufd' of git://git.kernel.org/pub/scm/linux/kernel/git/jgg/iommufd:
iommufd: Add config needed for iommufd_fail_nth
iommufd: Add missing IOMMUFD_DRIVER kconfig for the selftest
Pull rdma fixes from Jason Gunthorpe:
- Add a missing mutex_destroy() in rxe
- Enhance the debugging print for cm_destroy failures to help debug
these
- Fix mlx5 MAD processing in cases where multiport devices are running
in switchedev mode
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Fix port number for counter query in multi-port configuration
RDMA/cm: Print the old state when cm_destroy_id gets timeout
RDMA/rxe: Fix the problem "mutex_destroy missing"
Pull fs/9p fixes from Eric Van Hensbergen:
"This contains a reversion of one of the original 6.9 patches which
seems to have been the cause of most of the instability. It also
incorporates several fixes to legacy support and cache fixes.
There are few additional changes to improve stability, but I want
another week of testing before sending them upstream"
* tag '9p-fixes-for-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
fs/9p: drop inodes immediately on non-.L too
fs/9p: Revert "fs/9p: fix dups even in uncached mode"
fs/9p: remove erroneous nlink init from legacy stat2inode
9p: explicitly deny setlease attempts
fs/9p: fix the cache always being enabled on files with qid flags
fs/9p: translate O_TRUNC into OTRUNC
fs/9p: only translate RWX permissions for plain 9P2000
Pull fuse fixes from Miklos Szeredi:
- Fix two bugs in the new passthrough mode
- Fix a statx bug introduced in v6.6
- Fix code documentation
* tag 'fuse-fixes-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
cuse: add kernel-doc comments to cuse_process_init_reply()
fuse: fix leaked ENOSYS error on first statx call
fuse: fix parallel dio write on file open in passthrough mode
fuse: fix wrong ff->iomode state changes from parallel dio write
Pull arm64 fixes from Catalin Marinas:
- Fix a kernel fault during page table walking in huge_pte_alloc() with
PTABLE_LEVELS=5 due to using p4d_offset() instead of p4d_alloc()
- head.S fix and cleanup to disable the MMU before toggling the
HCR_EL2.E2H bit when entering the kernel with the MMU on from the EFI
stub. Changing this bit (currently from VHE to nVHE) causes some
system registers as well as page table descriptors to be interpreted
differently, potentially resulting in spurious MMU faults
- Fix translation fault in swsusp_save() accessing MEMBLOCK_NOMAP
memory ranges due to kernel_page_present() returning true in most
configurations other than rodata_full == true,
CONFIG_DEBUG_PAGEALLOC=y or CONFIG_KFENCE=y
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: hibernate: Fix level3 translation fault in swsusp_save()
arm64/head: Disable MMU at EL2 before clearing HCR_EL2.E2H
arm64/head: Drop unnecessary pre-disable-MMU workaround
arm64/hugetlb: Fix page table walk in huge_pte_alloc()
Pull s390 updates from Alexander Gordeev:
- Fix NULL pointer dereference in program check handler
- Fake IRBs are important events relevant for problem analysis. Add
traces when queueing and delivering
- Fix a race condition in ccw_device_set_online() that can cause the
online process to fail
- Deferred condition code 1 response indicates that I/O was not started
and should be retried. The current QDIO implementation handles a cc1
response as an error, resulting in a failed QDIO setup. Fix that by
retrying the setup when a cc1 response is received
* tag 's390-6.9-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: Fix NULL pointer dereference
s390/cio: log fake IRB events
s390/cio: fix race condition during online processing
s390/qdio: handle deferred cc1
Pull bootconfig fixes from Masami Hiramatsu:
- Fix potential static_command_line buffer overrun.
Currently we allocate the memory for static_command_line based on
"boot_command_line", but it will copy "command_line" into it. So we
use the length of "command_line" instead of "boot_command_line" (as
we previously did)
- Use memblock_free_late() in xbc_exit() instead of memblock_free()
after the buddy system is initialized
- Fix a kerneldoc warning
* tag 'bootconfig-fixes-v6.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
bootconfig: Fix the kerneldoc of _xbc_exit()
bootconfig: use memblock_free_late to free xbc memory to buddy
init/main.c: Fix potential static_command_line memory overflow
Pull thermal control fix from Rafael Wysocki:
"This prevents the thermal debug code from attempting to divide by zero
and corrects trip point statistics (Rafael Wysocki)"
* tag 'thermal-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/debugfs: Add missing count increment to thermal_debug_tz_trip_up()
Pull sound fixes from Takashi Iwai:
"Things look calm and normal, we got handful HD-audio-related small
fixes and a fix for MIDI 2.0 UMP handling"
* tag 'sound-6.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: seq: ump: Fix conversion from MIDI2 to MIDI1 UMP messages
ALSA: hda/realtek - Enable audio jacks of Haier Boyue G42 with ALC269VC
ALSA: hda/realtek: Add quirks for Huawei Matebook D14 NBLB-WAX9N
ALSA: hda/realtek: Fix volumn control of ThinkBook 16P Gen4
ALSA: hda/realtek: Fixes for Asus GU605M and GA403U sound
ALSA: hda/tas2781: Add new vendor_id and subsystem_id to support ThinkPad ICE-1
ALSA: hda/tas2781: correct the register for pow calibrated data
ALSA: hda/realtek: Add quirk for HP SnowWhite laptops
Pull drm fixes from Dave Airlie:
"Regular week of fixes, seems to be about right for this time in the
release cycle, amdgpu, and nouveau are the main one with some
scattered fixes otherwise.
ttm:
- Stop pooling cached NUMA pages
amdgpu:
- Fix invalid resource->start check
- USB-C DSC fix
- Fix a potential UAF in VA IOCTL
- Fix visible VRAM handling during faults
amdkfd:
- Fix memory leak in create_process failure
radeon:
- Silence UBSAN warnings from variable sized arrays
nouveau:
- dp: Don't probe DP ports twice
- nv04: Fix OOB access
- nv50: Disable AUX bus for disconnected DP ports
- nvkm: Fix instmem race condition
panel:
- Don't unregister DSI devices in several drivers
v3d:
- Fix enabled_ns increment
xe:
- Fix bo leak on error path during fb init
- Fix use-after-free due to order vm is put and destroyed"
* tag 'drm-fixes-2024-04-19' of https://gitlab.freedesktop.org/drm/kernel:
drm/radeon: silence UBSAN warning (v3)
drm/radeon: make -fstrict-flex-arrays=3 happy
drm/amdgpu: fix visible VRAM handling during faults
drm/amdgpu: validate the parameters of bo mapping operations more clearly
Revert "drm/amd/display: fix USB-C flag update after enc10 feature init"
drm/amdkfd: Fix memory leak in create_process failure
drm/amdgpu: remove invalid resource->start check v2
drm/xe/vm: prevent UAF with asid based lookup
drm/xe: Fix bo leak in intel_fb_bo_framebuffer_init
drm/panel: novatek-nt36682e: don't unregister DSI device
drm/panel: visionox-rm69299: don't unregister DSI device
drm/nouveau/dp: Don't probe eDP ports twice harder
drm/nouveau/kms/nv50-: Disable AUX bus for disconnected DP ports
drm/v3d: Don't increment `enabled_ns` twice
drm/vmwgfx: Sort primary plane formats by order of preference
drm/vmwgfx: Fix crtc's atomic check conditional
drm/vmwgfx: Fix prime import/export
drm/ttm: stop pooling cached NUMA pages v2
drm: nv04: Fix out of bounds access
nouveau: fix instmem race condition around ptr stores
