In DCN401 pre-blending degamma LUT isn't affecting cursor as in previous
DCN version. As this is not the behavior close to what is expected for
CRTC degamma LUT, disable CRTC degamma LUT property in this HW.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/4176
---
When enabling HDR on KDE, it takes the first CRTC 1D LUT available and
apply a color transformation (Gamma 2.2 -> PQ). AMD driver usually
advertises a CRTC degamma LUT as the first CRTC 1D LUT, but it's
actually applied pre-blending. In previous HW version, it seems to work
fine because the 1D LUT was applied to cursor too, but DCN401 presents a
different behavior and the 1D LUT isn't affecting the hardware cursor.
To address the wrong gamma on cursor with HDR (see the link), I came up
with this patch that disables CRTC degamma LUT in this hw, since it
presents a different behavior than others. With this KDE sees CRTC
regamma LUT as the first post-blending 1D LUT available. This is
actually more consistent with AMD color pipeline. It was tested by the
reporter, since I don't have the HW available for local testing and
debugging.
Melissa
---
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SmartMux is a mechanism to switch the GPU being used for scanout in a
hybrid configuration. This is used for devices with an eDP and two GPUs.
This is only valid when the system has a physical switch (Multiplexer)
in the board to switch between the two GPUs.
When a graphically intensive workload like a game is being run, the
system can be switch the active display to the dGPU, so that we can
avoid copying the buffer from dGPU to APU for scanout. This helps with
latency and FPS. When power consumption is preferred, the system can be
switched to the APU.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
UHBR link rate capable eDPs will use HPO for encoding. Need to pass
HPO stream and link encoder instances to DMCUB for Replay FSM to
know which instances to use.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why & how]
DP1 eDP is still considered a single-eDP case and should support Panel Replay.
Modify secondary eDP policy to reflect this and update Replay state accordingly.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Ovidiu Bunea <Ovidiu.Bunea@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
For SQ128 pattern some vendor-specific overrides are required.
Previously a hardcoded clock gen source value was incorrectly programmed,
causing our override to retimer's clock source override to be ignored.
Due to some PHY issues on certain APU programs, we see failures on retimer
bypass ports extend to electrical testing downstream of PHY due to some host
clock jitter which the retimer follows.
[HOW]
Fix typo to use correct clock gen source override of 0xC4 rather than 0x4C.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
To facilitate debugging, the following behaviors are defined for existing
debug option disable_ips_in_vpb
0 - Enable IPS in LVP - let driver decide (legacy)
1 - Disable IPS in LVP
2 - Enable IPS1 and RCG in LVP
3 - Enable IPS1 Z8, IPS1 and RCG in LVP
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Aligned IPS FW state with DMCUB IPS FW state
Added debug option disable_ips_rcg to modify RCG behaviour in IPS modes.
Updated existing debug option disable_ips to align with new changes introduced by IPSv2.0
Reviewed-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Leo Chen <leo.chen@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc has some code out of sync:
dc_commit_updates_for_stream handles v1/v2/v3,
but dc_update_planes_and_stream makes v1 asic to use v2.
as a reression fix: limit clear_update_flags to dcn32 or newer asic.
need to follow up that v1 asic using v2 issue.
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DSC block level should only be responsible for reporting single DSC
instance capabilities. Factoring in ODM combine requirements should be
handled in dc_dsc.c. Both components should acquire clocks from clk_mgr
to determine throughput capabilities instead of relying on hard coded
values as these can differ by SoC and SKU.
[HOW]
1) Add dsc_get_single_enc_caps to acquire single DSC instance
capabilities (replacing dsc_get_enc_caps), factoring in DSCCLK
2) add build_dsc_enc_caps to combine single DSC instance capabilities
3) account for max pixel rate per pipe (DISPCLK) when calculating
minimum slice count
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When booting without an HDMI display connected, the I2C registers
are not initialized correctly, leading to DC_I2C_ARBITRATION register
getting stuck with DC_I2C_REG_RW_CNTL_STATUS == USED_BY_SW.
[How]
* Correct TOCTOU race condition in engine acquire logic which did not
check against DMUB trying to acquire it at the same time.
* Deassert SOFT_RESET before acquire, as it can block access to other
I2C registers.
* Add a workaround in release, checking that after triggerring
DC_I2C_SW_DONE_USING_I2C_REG, DC_I2C_REG_RW_CNTL_STATUS != USED_BY_SW.
If necessary, trigger DC_I2C_SW_DONE_USING_I2C_REG again.
* Remove unnecessary clear of DC_I2C_SW_USE_I2C_REG_REQ, which engine
ignores according to specification.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dominik Kaszewski <dominik.kaszewski@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When the driver is unloaded, the interrupt source of
the rma device is not released, resulting in the failure
of hw_init when loading again using bad_page_threshold.
Signed-off-by: Ce Sun <cesun102@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It turns out that the fixup from vlv_fixup_mipi_sequences() is necessary
for some DSI panel's with version 2 mipi-sequences too.
Specifically the Acer Iconia One 8 A1-840 (not to be confused with the
A1-840FHD which is different) has the following sequences:
BDB block 53 (1284 bytes) - MIPI sequence block:
Sequence block version v2
Panel 0 *
Sequence 2 - MIPI_SEQ_INIT_OTP
GPIO index 9, source 0, set 0 (0x00)
Delay: 50000 us
GPIO index 9, source 0, set 1 (0x01)
Delay: 6000 us
GPIO index 9, source 0, set 0 (0x00)
Delay: 6000 us
GPIO index 9, source 0, set 1 (0x01)
Delay: 25000 us
Send DCS: Port A, VC 0, LP, Type 39, Length 5, Data ff aa 55 a5 80
Send DCS: Port A, VC 0, LP, Type 39, Length 3, Data 6f 11 00
...
Send DCS: Port A, VC 0, LP, Type 05, Length 1, Data 29
Delay: 120000 us
Sequence 4 - MIPI_SEQ_DISPLAY_OFF
Send DCS: Port A, VC 0, LP, Type 05, Length 1, Data 28
Delay: 105000 us
Send DCS: Port A, VC 0, LP, Type 05, Length 2, Data 10 00
Delay: 10000 us
Sequence 5 - MIPI_SEQ_ASSERT_RESET
Delay: 10000 us
GPIO index 9, source 0, set 0 (0x00)
Notice how there is no MIPI_SEQ_DEASSERT_RESET, instead the deassert
is done at the beginning of MIPI_SEQ_INIT_OTP, which is exactly what
the fixup from vlv_fixup_mipi_sequences() fixes up.
Extend it to also apply to v2 sequences, this fixes the panel not working
on the Acer Iconia One 8 A1-840.
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/14605
Signed-off-by: Hans de Goede <hansg@kernel.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250703143824.7121-1-hansg@kernel.org
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Add TRACE_GPU_MEM tracepoints for tracking global GPU memory usage.
These are required by VSR on Android 12+ for reporting GPU driver memory
allocations.
v5:
- Drop process_mem tracking
- Set the gpu_id field to dev->primary->index (Lucas, Tvrtko)
- Formatting cleanup under 80 columns
v3:
- Use now configurable CONFIG_TRACE_GPU_MEM instead of adding a
per-driver Kconfig (Lucas)
v2:
- Use u64 as preferred by checkpatch (Tvrtko)
- Fix errors in comments/Kconfig description (Tvrtko)
- drop redundant "CONFIG" in Kconfig
Signed-off-by: Juston Li <justonli@chromium.org>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@igalia.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://lore.kernel.org/r/20250709192313.479336-2-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
The object is potentially already gone after the drm_gem_object_put().
In general the object should be fully constructed before calling
drm_gem_handle_create(), except the debugfs tracking uses a separate
lock and list and separate flag to denotate whether the object is
actually initialized.
Since I'm touching this all anyway simplify this by only adding the
object to the debugfs when it's ready for that, which allows us to
delete that separate flag. panthor_gem_debugfs_bo_rm() already checks
whether we've actually been added to the list or this is some error
path cleanup.
v2: Fix build issues for !CONFIG_DEBUGFS (Adrián)
v3: Add linebreak and remove outdated comment (Liviu)
Fixes: a3707f53eb ("drm/panthor: show device-wide list of DRM GEM objects over DebugFS")
Cc: Adrián Larumbe <adrian.larumbe@collabora.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Steven Price <steven.price@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Simona Vetter <simona.vetter@intel.com>
Signed-off-by: Simona Vetter <simona.vetter@ffwll.ch>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20250709135220.1428931-1-simona.vetter@ffwll.ch
