This patch fix a power-on issue, and avoid to retry the power sequence.
In power off sequence: sdmmc must set pwr_reg in "power-cycle" state
(value 0x2), to prevent the card from being supplied through the signal
lines (all the lines are driven low).
In power on sequence: when the power is stable, sdmmc must set pwr_reg
in "power-off" state (value 0x0) to drive all signal to high before to
set "power-on".
To avoid writing the same value to the power register several times, this
register is cached by the pwr_reg variable. At probe pwr_reg is initialized
to 0 by kzalloc of mmc_alloc_host.
Like pwr_reg value is 0 at probing, the power on sequence fail because
the "power-off" state is not writes (value 0x0) and the lines
remain drive to low.
This patch initializes "pwr_reg" variable with power register value.
This it done in sdmmc variant init to not disturb default mmci behavior.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20200420161831.5043-1-ludovic.barre@st.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some commands uses R1B responses, which means the card may assert the DAT0
line to signal busy for a period of time, after it has received the
command. The mmc core normally specifies the busy period for the command in
the cmd->busy_timeout. Ideally the driver should respect it, but that
requires quite some update of the code, so let's defer that to someone with
the HW at hand.
Instead, let's inform the mmc core about the maximum supported busy timeout
in ->max_busy_timeout during ->probe(). This value corresponds to the fixed
4s timeout used by usdhi6rol0. In this way, we let the mmc core validate
the needed timeout, which may lead to that it converts from a R1B into a R1
response and then use CMD13 to poll for busy completion.
In other words, this change enables support for commands with longer busy
periods than 4s, like erase (CMD38) for example.
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Lars Persson <lars.persson@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Link: https://lore.kernel.org/r/20200414161413.3036-6-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using a fixed 2s timeout for all commands is a bit problematic.
For some commands it means waiting longer than needed for the timer to
expire, which may not a big issue, but still. For other commands, like for
an erase (CMD38) that uses a R1B response, may require longer timeouts than
2s. In these cases, we may end up treating the command as it failed, while
it just needed some more time to complete successfully.
Fix the problem by respecting the cmd->busy_timeout, which is provided by
the mmc core.
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200414161413.3036-4-ulf.hansson@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When use one SDIO wifi which enable the runtime PM feature on i.MX6SX,
we meet system hang. This hang happened during the usdhc runtime resume,
in sdhci_init(), when call the sdhci_set_default_irqs. One interrupt
(SDHCI_INT_CARD_INT) triggered just after the host->ier update and before
the write of register SDHCI_SIGNAL_ENABLE. So in sdhci_irq, it will skip
the call of sdio_signal_irq() because current host->ier do not set the
SDHCI_INT_CARD_INT. So this SDIO wifi interrupt always keep triggered,
let the system stuck in irq handle, can't response any other thread.
This patch add spin lock for the sdhci_set_default_irqs to fix this issue.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1586941255-9237-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SD host controller can process one request in the atomic context if
the card is nonremovable, which means we can submit next request in the
irq hard handler when using the MMC host software queue to reduce the
latency. Thus this patch adds a new API request_atomic() for the host
controller, as well as adding support for host software queue to submit
a request by the new request_atomic() API.
Moreover there is an unusual case that the card is busy when trying to
send a command, and we can not polling the card status in interrupt
context by using request_atomic() to dispatch requests. Thus we should
queue a work to try again in the non-atomic context in case the host
releases the busy signal later.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/a344e27e506cb2329073cbd5cf65e15cc3cbeba9.1586744073.git.baolin.wang7@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Spending time under spinlock increases IRQ latencies and also
response times because preemption is disabled.
sdhci_send_command() waits up to 10 ms under spinlock for inhibit bits
to clear. In general inhibit bits will not be set, but there may be
corner cases, especially in the face of errors, where waiting helps.
There might also be dysfunctional hardware that needs the waiting. So
retain the legacy behaviour but do not wait for inhibit bits while under
spinlock. Instead adjust the logic to enable waiting while not under
spinlock. That is mostly straight forward, but in the interrupt handler
it requires deferring an "inhibited" command to the IRQ thread where
sleeping is allowed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Baolin Wang <baolin.wang7@gmail.com>
Link: https://lore.kernel.org/r/20200412090349.1607-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of reimplementing the logic in mmc_regulator_set_vqmmc(), use the
mmc code function directly.
This also allows us to fix a related issue on STM32MP1, when a voltage
switch of 1.8V is done for the eMMC, but the current level is already set
to 1.8V. More precisely, in this scenario the call to the
->post_sig_volt_switch() hangs, indefinitely waiting for the voltage switch
to complete. Fix this problem by checking if mmc_regulator_set_vqmmc()
returned 1 and then skip invoking the callback.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-3-marex@denx.de
[Ulf: Updated the commit message]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Patch all drivers which use mmc_regulator_set_vqmmc() and prepare them for
the fact that mmc_regulator_set_vqmmc() can return a value > 0, which would
happen if the signal voltage switch did NOT happen, because the voltage was
already set correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20200416163649.336967-1-marex@denx.de
[Ulf: Re-worked/simplified the code a bit]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Clang warns:
drivers/mmc/host/sdhci-of-arasan.c:784:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:738:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
drivers/mmc/host/sdhci-of-arasan.c:860:9: warning: variable 'ret' is
uninitialized when used here [-Wuninitialized]
return ret;
^~~
drivers/mmc/host/sdhci-of-arasan.c:810:9: note: initialize the variable
'ret' to silence this warning
int ret;
^
= 0
2 warnings generated.
This looks like a copy paste error. Neither function has handling that
needs ret so just remove it and return 0 directly.
Link: https://github.com/ClangBuiltLinux/linux/issues/996
Reported-by: kernelci.org bot <bot@kernelci.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20200416182402.16858-1-natechancellor@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the SDHCI specification, the Capabilities Register (Offset 0x40h)
is the 64-bit width register, but in Linux, it is represented as two
registers, SDHCI_CAPABILITIES and SDHCI_CAPABILITIES_1 so that drivers
can use 32-bit register accessors.
The upper 32-bit field is associated with SDHCI_CAPABILITIES_1.
Move the definition of SDHCI_CAPABILITIES_1 to the correct place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200408072105.422-1-yamada.masahiro@socionext.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull EFI fixes from Thomas Gleixner:
"A set of EFI fixes:
- Don't return a garbage screen info when EFI framebuffer is not
available
- Make the early EFI console work properly with wider fonts instead
of drawing garbage
- Prevent a memory buffer leak in allocate_e820()
- Print the firmware error record properly so it can be decoded by
users
- Fix a symbol clash in the host tool build which only happens with
newer compilers.
- Add a missing check for the event log version of TPM which caused
boot failures on several Dell systems due to an attempt to decode
SHA-1 format with the crypto agile algorithm"
* tag 'efi-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tpm: check event log version before reading final events
efi: Pull up arch-specific prototype efi_systab_show_arch()
x86/boot: Mark global variables as static
efi: cper: Add support for printing Firmware Error Record Reference
efi/libstub/x86: Avoid EFI map buffer alloc in allocate_e820()
efi/earlycon: Fix early printk for wider fonts
efi/libstub: Avoid returning uninitialized data from setup_graphics()
Pull x86 fixes from Thomas Gleixner:
"Two fixes for x86:
- Unbreak stack dumps for inactive tasks by interpreting the special
first frame left by __switch_to_asm() correctly.
The recent change not to skip the first frame so ORC and frame
unwinder behave in the same way caused all entries to be
unreliable, i.e. prepended with '?'.
- Use cpumask_available() instead of an implicit NULL check of a
cpumask_var_t in mmio trace to prevent a Clang build warning"
* tag 'x86-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind/orc: Fix unwind_get_return_address_ptr() for inactive tasks
x86/mmiotrace: Use cpumask_available() for cpumask_var_t variables
Pull scheduler fixes from Thomas Gleixner:
"A set of fixes for the scheduler:
- Fix handling of throttled parents in enqueue_task_fair() completely.
The recent fix overlooked a corner case where the first iteration
terminates due to an entity already being on the runqueue which
makes the list management incomplete and later triggers the
assertion which checks for completeness.
- Fix a similar problem in unthrottle_cfs_rq().
- Show the correct uclamp values in procfs which prints the effective
value twice instead of requested and effective"
* tag 'sched-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix unthrottle_cfs_rq() for leaf_cfs_rq list
sched/debug: Fix requested task uclamp values shown in procfs
sched/fair: Fix enqueue_task_fair() warning some more
Pull networking fixes from David Miller:
1) Fix RCU warnings in ipv6 multicast router code, from Madhuparna
Bhowmik.
2) Nexthop attributes aren't being checked properly because of
mis-initialized iterator, from David Ahern.
3) Revert iop_idents_reserve() change as it caused performance
regressions and was just working around what is really a UBSAN bug
in the compiler. From Yuqi Jin.
4) Read MAC address properly from ROM in bmac driver (double iteration
proceeds past end of address array), from Jeremy Kerr.
5) Add Microsoft Surface device IDs to r8152, from Marc Payne.
6) Prevent reference to freed SKB in __netif_receive_skb_core(), from
Boris Sukholitko.
7) Fix ACK discard behavior in rxrpc, from David Howells.
8) Preserve flow hash across packet scrubbing in wireguard, from Jason
A. Donenfeld.
9) Cap option length properly for SO_BINDTODEVICE in AX25, from Eric
Dumazet.
10) Fix encryption error checking in kTLS code, from Vadim Fedorenko.
11) Missing BPF prog ref release in flow dissector, from Jakub Sitnicki.
12) dst_cache must be used with BH disabled in tipc, from Eric Dumazet.
13) Fix use after free in mlxsw driver, from Jiri Pirko.
14) Order kTLS key destruction properly in mlx5 driver, from Tariq
Toukan.
15) Check devm_platform_ioremap_resource() return value properly in
several drivers, from Tiezhu Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (71 commits)
net: smsc911x: Fix runtime PM imbalance on error
net/mlx4_core: fix a memory leak bug.
net: ethernet: ti: cpsw: fix ASSERT_RTNL() warning during suspend
net: phy: mscc: fix initialization of the MACsec protocol mode
net: stmmac: don't attach interface until resume finishes
net: Fix return value about devm_platform_ioremap_resource()
net/mlx5: Fix error flow in case of function_setup failure
net/mlx5e: CT: Correctly get flow rule
net/mlx5e: Update netdev txq on completions during closure
net/mlx5: Annotate mutex destroy for root ns
net/mlx5: Don't maintain a case of del_sw_func being null
net/mlx5: Fix cleaning unmanaged flow tables
net/mlx5: Fix memory leak in mlx5_events_init
net/mlx5e: Fix inner tirs handling
net/mlx5e: kTLS, Destroy key object after destroying the TIS
net/mlx5e: Fix allowed tc redirect merged eswitch offload cases
net/mlx5: Avoid processing commands before cmdif is ready
net/mlx5: Fix a race when moving command interface to events mode
net/mlx5: Add command entry handling completion
rxrpc: Fix a memory leak in rxkad_verify_response()
...
Remove runtime PM usage counter decrement when the
increment function has not been called to keep the
counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5 fixes 2020-05-22
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.13
('net/mlx5: Add command entry handling completion')
For -stable v5.2
('net/mlx5: Fix error flow in case of function_setup failure')
('net/mlx5: Fix memory leak in mlx5_events_init')
For -stable v5.3
('net/mlx5e: Update netdev txq on completions during closure')
('net/mlx5e: kTLS, Destroy key object after destroying the TIS')
('net/mlx5e: Fix inner tirs handling')
For -stable v5.6
('net/mlx5: Fix cleaning unmanaged flow tables')
('net/mlx5: Fix a race when moving command interface to events mode')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In function mlx4_opreq_action(), pointer "mailbox" is not released,
when mlx4_cmd_box() return and error, causing a memory leak bug.
Fix this issue by going to "out" label, mlx4_free_cmd_mailbox() can
free this pointer.
Fixes: fe6f700d6c ("net/mlx4_core: Respond to operation request by firmware")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_for_each() are required to be called with rtnl_lock taken, otherwise
ASSERT_RTNL() warning will be triggered - which happens now during System
resume from suspend:
cpsw_suspend()
|- cpsw_ndo_stop()
|- __hw_addr_ref_unsync_dev()
|- cpsw_purge_all_mc()
|- vlan_for_each()
|- ASSERT_RTNL();
Hence, fix it by surrounding cpsw_ndo_stop() by rtnl_lock/unlock() calls.
Fixes: 15180eca56 ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At the very end of the MACsec block initialization in the MSCC PHY
driver, the MACsec "protocol mode" is set. This setting should be set
based on the PHY id within the package, as the bank used to access the
register used depends on this. This was not done correctly, and only the
first bank was used leading to the two upper PHYs being unstable when
using the VSC8584. This patch fixes it.
Fixes: 1bbe0ecc2a ("net: phy: mscc: macsec initialization")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
