The function may be used by the user directly and also by the n_gsm
internal functions. They can lead into a race condition which results in
interleaved frames if both are writing at the same time. The receiving side
is not able to decode those interleaved frames correctly.
Add a lock around the low side tty write to avoid race conditions and frame
interleaving between user originated writes and n_gsm writes.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-9-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current implementation control packets are re-transmitted even if
the control channel closed down during T2. This is wrong.
Check whether the control channel is open before re-transmitting any
packets. Note that control channel open/close is handled by T1 and not T2
and remains unaffected by this.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-7-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.6 states that FCoff stops the
transmission on all channels except the control channel. This is already
implemented in gsm_data_kick(). However, chapter 5.4.8.1 explains that this
shall result in the same behavior as software flow control on the ldisc in
advanced option mode. That means only flow control frames shall be sent
during flow off. The current implementation does not consider this case.
Change gsm_data_kick() to send only flow control frames if constipated to
abide the standard. gsm_read_ea_val() and gsm_is_flow_ctrl_msg() are
introduced as helper functions for this.
It is planned to use gsm_read_ea_val() in later code cleanups for other
functions, too.
Fixes: c01af4fec2 ("n_gsm : Flow control handling in Mux driver")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-5-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation does not handle the situation that no data is in
the internal queue and needs to be sent out while the user tty fifo is
full.
Add a timer that moves more data from user tty down to the internal queue
which is then serialized on the ldisc. This timer is triggered if no data
was moved from a user tty to the internal queue within 10 * T1.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-4-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) The function drains the fifo for the given user tty/DLCI without
considering 'TX_THRESH_HI' and different to gsm_dlci_data_output_framed(),
which moves only one packet from the user side to the internal transmission
queue. We can only handle one packet at a time here if we want to allow
DLCI priority handling in gsm_dlci_data_sweep() to avoid link starvation.
2) Furthermore, the additional header octet from convergence layer type 2
is not counted against MTU. It is part of the UI/UIH frame message which
needs to be limited to MTU. Hence, it is wrong not to consider this octet.
3) Finally, the waiting user tty is not informed about freed space in its
send queue.
Take at most one packet worth of data out of the DLCI fifo to fix 1).
Limit the max user data size per packet to MTU - 1 in case of convergence
layer type 2 to leave space for the control signal octet which is added in
the later part of the function. This fixes 2).
Add tty_port_tty_wakeup() to wake up the user tty if new write space has
been made available to fix 3).
Fixes: 268e526b93 ("tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-3-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation registers/deregisters the user ttys at mux
attach/detach. That means that the user devices are available before any
control channel is open. However, user channel initialization requires an
open control channel. Furthermore, the user is not informed if the mux
restarts due to configuration changes.
Put the registration/deregistration procedure into separate function to
improve readability.
Move registration to mux activation and deregistration to mux cleanup to
keep the user devices only open as long as a control channel exists. The
user will be informed via the device driver if the mux was reconfigured in
a way that required a mux re-activation.
This makes it necessary to add T2 initialization to gsmld_open() for the
ldisc open code path (not the reconfiguration code path) to avoid deletion
of an uninitialized T2 at mux cleanup.
Fixes: d50f6dcaf2 ("tty: n_gsm: expose gsmtty device nodes at ldisc open time")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-2-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After setting up the control channel on both sides the responder side may
want to open a virtual tty to listen on until the initiator starts an
application on a user channel. The current implementation allows the
open() but no other operation, like termios. These fail with EINVAL.
The responder sided application has no means to detect an open by the
initiator sided application this way. And the initiator sided applications
usually expect the responder sided application to listen on the user
channel upon open.
Set the user channel into half-open state on responder side once a user
application opens the virtual tty to allow IO operations on it.
Furthermore, keep the user channel constipated until the initiator side
opens it to give the responder sided application the chance to detect the
new connection and to avoid data loss if the responder sided application
starts sending before the user channel is open.
Fixes: e1eaea46bb ("tty: n_gsm line discipline")
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220701061652.39604-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the earlycon parameter is given twice, the kernel will spit out a
WARN() in register_console() because it was already registered. The
non-dt variant setup_earlycon() already handles that gracefully. The dt
variant of_setup_earlycon() doesn't. Add the check there and add the
-EALREADY handling in early_init_dt_scan_chosen_stdout().
FWIW, this doesn't happen if CONFIG_ACPI_SPCR_TABLE is set. In that case
the registration is delayed until after earlycon parameter(s) are
parsed.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20220628120705.200617-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Regarding Exynos Auto v9 SoC, it supports uarts up to 12. However, the
maximum number of the ports has been derived from
CONFIG_SERIAL_SAMSUNG_UARTS and tightly coupled with the config for
previous Samsung SoCs such as s3c24xx and s3c64xx. To overcome this
limitation, this changes the usage of the definition to UART_NR which is
widely used from other serial drivers. This also defines the value to 12
only for ARM64 SoCs to not affect the change to previous arm32 SoCs.
Instead of enumerating all the ports as predefined arrays, this
introduces s3c24xx_serial_init_port_default that is initializing the
structure as the default value.
Reviewed-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chanho Park <chanho61.park@samsung.com>
Link: https://lore.kernel.org/r/20220629005538.60132-1-chanho61.park@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for RS-485 multipoint addressing using 9th bit [*]. The
addressing mode is configured through ->rs485_config().
ADDRB in termios indicates 9th bit addressing mode is enabled. In this
mode, 9th bit is used to indicate an address (byte) within the
communication line. ADDRB can only be enabled/disabled through
->rs485_config() that is also responsible for setting the destination and
receiver (filter) addresses.
Add traps to detect unwanted changes to struct serial_rs485 layout using
static_assert().
[*] Technically, RS485 is just an electronic spec and does not itself
specify the 9th bit addressing mode but 9th bit seems at least
"semi-standard" way to do addressing with RS485.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use 32-bit reads in order to not lose higher bits of DW UART regs. This
change does not fix any known issue as the high bits are not used for
anything related to 8250 driver (dw8250_readl_ext and dw8250_writel_ext
used within the dwlib are already doing
readl/writel/ioread32be/iowrite32be anyway).
This change is necessary to enables 9th bit address mode. DW UART
reports address frames with BIT(8) of LSR.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 31f6bd7fad ("serial: Store character timing information
to uart_port"), per frame timing information is available on uart_port.
Uart port's timeout can be derived from frame_time by multiplying with
fifosize.
Most callers of uart_poll_timeout are not made under port's lock. To be
on the safe side, make sure frame_time is only accessed once. As
fifo_size is effectively a constant, it shouldn't cause any issues.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220613113905.22962-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220614090537.15557-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
