AT91 fixes#2 for 5.15:
- More fixes for AT91 platform power management code related to the
introduction of sama7g5:
- management of DDR3L regulator rails for sama7g5ek
- loading of TLB on different cores
- PIO controller slew-rate settings for sama7g5ek: be aligned with
datasheet requirements.
* tag 'at91-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama7g5ek: to not touch slew-rate for SDMMC pins
ARM: dts: at91: sama7g5ek: use proper slew-rate settings for GMACs
ARM: at91: pm: preload base address of controllers in tlb
ARM: at91: pm: group constants and addresses loading
ARM: dts: at91: sama7g5ek: add suspend voltage for ddr3l rail
Link: https://lore.kernel.org/r/20211004114344.19304-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With commit c709135e57 ("pinctrl: at91-pio4: add support for slew-rate")
and commit cbde6c823b ("pinctrl: at91-pio4: Fix slew rate disablement")
the slew-rate is enabled by default for each configured pin. The datasheet
specifies at chapter "Output Driver AC Characteristics" that HSIO
drivers (use in SDMMCx and QSPI0 peripherals), don't have a slewrate
setting but are rather calibrated against an external 1% resistor mounted
on the SDMMCx_CAL or QSPI0_CAL pins. Depending on the target signal
frequency and the external load, it is possible to adjust their target
output impedance. Thus set slew-rate = <0> for SDMMC (QSPI is not enabled
at the moment in device tree).
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-3-claudiu.beznea@microchip.com
Datasheet chapter "EMAC Timings" specifies that while in 3.3V domain
GMAC's MDIO pins should be configured with slew-rate enabled, while the
data + signaling pins should be configured with slew-rate disabled when
GMAC works in RGMII or RMII modes. The pin controller for SAMA7G5 sets
the slew-rate as enabled for all pins. Adapt the device tree to comply
with these.
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-2-claudiu.beznea@microchip.com
In suspend/resume procedure for AT91 architecture different controllers
(PMC, SHDWC, RAM, RAM PHY, SFRBU) are accessed to do the proper settings
for power saving. Commit f0bbf17958 ("ARM: at91: pm: add self-refresh
support for sama7g5") introduced the access to RAMC PHY controller for
SAMA7G5. The access to this controller is done after RAMC ports are
closed, thus any TLB walk necessary for RAMC PHY virtual address will
fail. In the development branch this was not encountered. However, on
current kernel the issue is reproducible.
To solve the issue the previous mechanism of pre-loading the TLB with
the RAMC PHY virtual address has been used. However, only the addition
of this new pre-load breaks the functionality for ARMv5 based
devices (SAM9X60). This behavior has been encountered previously
while debugging this code and using the same mechanism for pre-loading
address for different controllers (e.g. pin controller, the assumption
being that other requested translations are replaced from TLB).
To solve this new issue the TLB flush + the extension of pre-loading
the rest of controllers to TLB (e.g. PMC, RAMC) has been added. The
rest of the controllers should have been pre-loaded previously, anyway.
Fixes: f0bbf17958 ("ARM: at91: pm: add self-refresh support for sama7g5")
Depends-on: e42cbbe5c9 ("ARM: at91: pm: group constants and addresses loading")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-4-claudiu.beznea@microchip.com
SAMA7G5-EK board has DDR3L type of memory soldered. This needs 1.35V. The
1.35V for DDR3L rail at run-time is selected by the proper configuration
on SELV2 pin (for 1.35V it needs to be in high-z state). When suspended
the MCP16502 PMIC soldered on SAMA7G5-EK will use different sets of
configuration registers to provide proper voltages on its rail. Run-time
configuration registers could be configured differently than suspend
configuration register for MCP16502 (VSEL2 affects only run-time
configuration). In suspend states the DDR3L memory soldered on SAMA7G5-EK
switches to self-refresh. Even on self-refresh it needs to be powered by
a 1.35V rail. Thus, make sure the PMIC is configured properly when system
is suspended.
Fixes: 7540629e2f (ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-2-claudiu.beznea@microchip.com
AT91 fixes#1 for 5.15:
- Fixes for newly introduced SAMA7G5 and its Power Management code.
Associated core peripherals need to be instantiated in DT for
benefiting from best PM support like Backup mode with DDR in
Self-Refresh.
- Add chip ID for SAMA7G5 for easing the kernel log identification.
- Avoid Camera Sensor probe error on sama5d27 som1 ek board.
* tag 'at91-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: sama5d2_som1_ek: disable ISC node by default
ARM: at91: pm: switch backup area to vbat in backup mode
ARM: dts: at91: sama7g5: add chipid
ARM: dts: at91: sama7g5: add shdwc node
ARM: dts: at91: sama7g5: add securam node
ARM: dts: at91: sama7g5: add ram controllers
ARM: at91: pm: do not panic if ram controllers are not enabled
Link: https://lore.kernel.org/r/20210914162314.54347-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Backup area is now switched to VDDIN33 at boot (with the help of
bootloader). When switching to backup mode we need to switch backup area
to VBAT as all the other power sources are cut off. The resuming from
backup mode is done with the help of bootloader, so there is no need to
do something particular in Linux to restore backup area power source.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210830100927.22711-1-claudiu.beznea@microchip.com
DRM_FBDEV_EMULATION previously selected FB and was default y as long as DRM
was enabled. In commit f611b1e762 ("drm: Avoid circular dependencies for
CONFIG_FB") the select was replaced with a depends on FB, disabling the
drivers that depended on it.
Renable FB so we get back FB_EFI, FB_WM8505, FB_SH_MOBILE_LCDC, FB_SIMPLE and
VIDEO_VIVID.
It must be set to y and not a module as the test driver VIDEO_VIVID
requires it to be built in.
Link: https://lore.kernel.org/r/CAK8P3a18EdBKQdGDOZc9cPKsf=hY8==v2cO0DBE_tyd82Uq-Ng@mail.gmail.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Some drivers have not been built as they gained dependencies in kconfig but those
dependencies were not added to the defconfig.
The MSM pinctrl drivers fell out of the defconfig as of commit be117ca322
("pinctrl: qcom: Kconfig: Rework PINCTRL_MSM to be a depenency rather then a
selected config"). Add PINCTRL_MSM so these stay enabled.
EDAC depends on RAS, so enable it to ensure the EDAC drivers stay
enabled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
sizeof when applied to a pointer typed expression gives the size of
the pointer.
./drivers/tee/optee/shm_pool.c:38:28-34: ERROR application of sizeof to pointer
This issue was detected with the help of Coccinelle.
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: jing yangyang <jing.yangyang@zte.com.cn>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Add missing fields and remove some duplicate fields when printing a
perf_event_attr.
- Fix hybrid config terms list corruption.
- Update kernel header copies, some resulted in new kernel features
being automagically added to 'perf trace' syscall/tracepoint argument
id->string translators.
- Add a file generated during the documentation build to .gitignore.
- Add an option to build without libbfd, as some distros, like Debian
consider its ABI unstable.
- Add support to print a textual representation of IBS raw sample data
in 'perf report'.
- Fix bpf 'perf test' sample mismatch reporting
- Fix passing arguments to stackcollapse report in a 'perf script'
python script.
- Allow build-id with trailing zeros.
- Look for ImageBase in PE file to compute .text offset.
* tag 'perf-tools-for-v5.15-2021-09-11' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: (25 commits)
tools headers UAPI: Update tools's copy of drm.h headers
tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
tools headers UAPI: Sync linux/fs.h with the kernel sources
tools headers UAPI: Sync linux/in.h copy with the kernel sources
perf tools: Add an option to build without libbfd
perf tools: Allow build-id with trailing zeros
perf tools: Fix hybrid config terms list corruption
perf tools: Factor out copy_config_terms() and free_config_terms()
perf tools: Fix perf_event_attr__fprintf() missing/dupl. fields
perf tools: Ignore Documentation dependency file
perf bpf: Provide a weak btf__load_from_kernel_by_id() for older libbpf versions
tools include UAPI: Update linux/mount.h copy
perf beauty: Cover more flags in the move_mount syscall argument beautifier
tools headers UAPI: Sync linux/prctl.h with the kernel sources
tools include UAPI: Sync sound/asound.h copy with the kernel sources
tools headers UAPI: Sync linux/kvm.h with the kernel sources
tools headers UAPI: Sync x86's asm/kvm.h with the kernel sources
perf report: Add support to print a textual representation of IBS raw sample data
perf report: Add tools/arch/x86/include/asm/amd-ibs.h
perf env: Add perf_env__cpuid, perf_env__{nr_}pmu_mappings
...
Pull compiler attributes updates from Miguel Ojeda:
- Fix __has_attribute(__no_sanitize_coverage__) for GCC 4 (Marco Elver)
- Add Nick as Reviewer for compiler_attributes.h (Nick Desaulniers)
- Move __compiletime_{error|warning} (Nick Desaulniers)
* tag 'compiler-attributes-for-linus-v5.15-rc1-v2' of git://github.com/ojeda/linux:
compiler_attributes.h: move __compiletime_{error|warning}
MAINTAINERS: add Nick as Reviewer for compiler_attributes.h
Compiler Attributes: fix __has_attribute(__no_sanitize_coverage__) for GCC 4
Pull auxdisplay updates from Miguel Ojeda:
"An assortment of improvements for auxdisplay:
- Replace symbolic permissions with octal permissions (Jinchao Wang)
- ks0108: Switch to use module_parport_driver() (Andy Shevchenko)
- charlcd: Drop unneeded initializers and switch to C99 style (Andy
Shevchenko)
- hd44780: Fix oops on module unloading (Lars Poeschel)
- Add I2C gpio expander example (Ralf Schlatterbeck)"
* tag 'auxdisplay-for-linus-v5.15-rc1' of git://github.com/ojeda/linux:
auxdisplay: Replace symbolic permissions with octal permissions
auxdisplay: ks0108: Switch to use module_parport_driver()
auxdisplay: charlcd: Drop unneeded initializers and switch to C99 style
auxdisplay: hd44780: Fix oops on module unloading
auxdisplay: Add I2C gpio expander example
Pull CPU hotplug updates from Thomas Gleixner:
"Updates for the SMP and CPU hotplug:
- Remove DEFINE_SMP_CALL_CACHE_FUNCTION() which is a left over of the
original hotplug code and now causing trouble with the ARM64 cache
topology setup due to the pointless SMP function call.
It's not longer required as the hotplug callbacks are guaranteed to
be invoked on the upcoming CPU.
- Remove the deprecated and now unused CPU hotplug functions
- Rewrite the CPU hotplug API documentation"
* tag 'smp-urgent-2021-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Documentation: core-api/cpuhotplug: Rewrite the API section
cpu/hotplug: Remove deprecated CPU-hotplug functions.
thermal: Replace deprecated CPU-hotplug functions.
drivers: base: cacheinfo: Get rid of DEFINE_SMP_CALL_CACHE_FUNCTION()
Pull misc driver fix from Greg KH:
"Here is a single patch for 5.15-rc1, for the lkdtm misc driver.
It resolves a build issue that many people were hitting with your
current tree, and Kees and others felt would be good to get merged
before -rc1 comes out, to prevent them from having to constantly hit
it as many development trees restart on -rc1, not older -rc releases.
It has NOT been in linux-next, but has passed 0-day testing and looks
'obviously correct' when reviewing it locally :)"
* tag 'char-misc-5.15-rc1-lkdtm' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
lkdtm: Use init_uts_ns.name instead of macros
Pull IPMI updates from Corey Minyard:
"A couple of very minor fixes for style and rate limiting.
Nothing big, but probably needs to go in"
* tag 'for-linus-5.15-1' of git://github.com/cminyard/linux-ipmi:
char: ipmi: use DEVICE_ATTR helper macro
ipmi: rate limit ipmi smi_event failure message
Pull scheduler fixes from Borislav Petkov:
- Make sure the idle timer expires in hardirq context, on PREEMPT_RT
- Make sure the run-queue balance callback is invoked only on the
outgoing CPU
* tag 'sched_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Prevent balance_push() on remote runqueues
sched/idle: Make the idle timer expire in hard interrupt context
Pull locking fixes from Borislav Petkov:
- Fix the futex PI requeue machinery to not return to userspace in
inconsistent state
- Avoid a potential null pointer dereference in the ww_mutex deadlock
check
- Other smaller cleanups and optimizations
* tag 'locking_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rtmutex: Fix ww_mutex deadlock check
futex: Remove unused variable 'vpid' in futex_proxy_trylock_atomic()
futex: Avoid redundant task lookup
futex: Clarify comment for requeue_pi_wake_futex()
futex: Prevent inconsistent state and exit race
futex: Return error code instead of assigning it without effect
locking/rwsem: Add missing __init_rwsem() for PREEMPT_RT
Pull timer fix from Borislav Petkov:
- Handle negative second values properly when converting a timespec64
to nanoseconds.
* tag 'timers_urgent_for_v5.15_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Handle negative seconds correctly in timespec64_to_ns()
Pull namei updates from Al Viro:
"Clearing fallout from mkdirat in io_uring series. The fix in the
kern_path_locked() patch plus associated cleanups"
* 'misc.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
putname(): IS_ERR_OR_NULL() is wrong here
namei: Standardize callers of filename_create()
namei: Standardize callers of filename_lookup()
rename __filename_parentat() to filename_parentat()
namei: Fix use after free in kern_path_locked
Pull smbfs updates from Steve French:
"cifs/smb3 updates:
- DFS reconnect fix
- begin creating common headers for server and client
- rename the cifs_common directory to smbfs_common to be more
consistent ie change use of the name cifs to smb (smb3 or smbfs is
more accurate, as the very old cifs dialect has long been
superseded by smb3 dialects).
In the future we can rename the fs/cifs directory to fs/smbfs.
This does not include the set of multichannel fixes nor the two
deferred close fixes (they are still being reviewed and tested)"
* tag '5.15-rc-cifs-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: properly invalidate cached root handle when closing it
cifs: move SMB FSCTL definitions to common code
cifs: rename cifs_common to smbfs_common
cifs: update FSCTL definitions
Pull virtio updates from Michael Tsirkin:
- vduse driver ("vDPA Device in Userspace") supporting emulated virtio
block devices
- virtio-vsock support for end of record with SEQPACKET
- vdpa: mac and mq support for ifcvf and mlx5
- vdpa: management netlink for ifcvf
- virtio-i2c, gpio dt bindings
- misc fixes and cleanups
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (39 commits)
Documentation: Add documentation for VDUSE
vduse: Introduce VDUSE - vDPA Device in Userspace
vduse: Implement an MMU-based software IOTLB
vdpa: Support transferring virtual addressing during DMA mapping
vdpa: factor out vhost_vdpa_pa_map() and vhost_vdpa_pa_unmap()
vdpa: Add an opaque pointer for vdpa_config_ops.dma_map()
vhost-iotlb: Add an opaque pointer for vhost IOTLB
vhost-vdpa: Handle the failure of vdpa_reset()
vdpa: Add reset callback in vdpa_config_ops
vdpa: Fix some coding style issues
file: Export receive_fd() to modules
eventfd: Export eventfd_wake_count to modules
iova: Export alloc_iova_fast() and free_iova_fast()
virtio-blk: remove unneeded "likely" statements
virtio-balloon: Use virtio_find_vqs() helper
vdpa: Make use of PFN_PHYS/PFN_UP/PFN_DOWN helper macro
vsock_test: update message bounds test for MSG_EOR
af_vsock: rename variables in receive loop
virtio/vsock: support MSG_EOR bit processing
vhost/vsock: support MSG_EOR bit processing
...
Pull more RISC-V updates from Palmer Dabbelt:
- A pair of defconfig additions, for NVMe and the EFI filesystem
localization options.
- A larger address space for stack randomization.
- A cleanup to our install rules.
- A DTS update for the Microchip Icicle board, to fix the serial
console.
- Support for build-time table sorting, which allows us to have
__ex_table read-only.
* tag 'riscv-for-linus-5.15-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Move EXCEPTION_TABLE to RO_DATA segment
riscv: Enable BUILDTIME_TABLE_SORT
riscv: dts: microchip: mpfs-icicle: Fix serial console
riscv: move the (z)install rules to arch/riscv/Makefile
riscv: Improve stack randomisation on RV64
riscv: defconfig: enable NLS_CODEPAGE_437, NLS_ISO8859_1
riscv: defconfig: enable BLK_DEV_NVME
Pull coccinelle updates from Julia Lawall:
"These changes update some existing semantic patches with
respect to some recent changes in the kernel.
Specifically, the change to kvmalloc.cocci searches for
kfree_sensitive rather than kzfree, and the change to
use_after_iter.cocci adds list_entry_is_head as a valid
use of a list iterator index variable after the end of
the loop"
* 'for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jlawall/linux:
scripts: coccinelle: allow list_entry_is_head() to use pos
coccinelle: api: rename kzfree to kfree_sensitive
Picking the changes from:
17ce9c61c7 ("drm: document DRM_IOCTL_MODE_RMFB")
Doesn't result in any tooling changes:
$ tools/perf/trace/beauty/drm_ioctl.sh > before
$ cp include/uapi/drm/drm.h tools/include/uapi/drm/drm.h
$ tools/perf/trace/beauty/drm_ioctl.sh > after
$ diff -u before after
Silencing these perf build warnings:
Warning: Kernel ABI header at 'tools/include/uapi/drm/drm.h' differs from latest version at 'include/uapi/drm/drm.h'
diff -u tools/include/uapi/drm/drm.h include/uapi/drm/drm.h
Cc: Simon Ser <contact@emersion.fr>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick the changes in:
b65a948973 ("drm/i915/userptr: Probe existence of backing struct pages upon creation")
ee242ca704 ("drm/i915/guc: Implement GuC priority management")
81340cf3bd ("drm/i915/uapi: reject set_domain for discrete")
7961c5b60f ("drm/i915: Add TTM offset argument to mmap.")
aef7b67a79 ("drm/i915/uapi: convert drm_i915_gem_userptr to kernel doc")
e7737b67ab ("drm/i915/uapi: reject caching ioctls for discrete")
3aa8c57fe2 ("drm/i915/uapi: convert drm_i915_gem_set_domain to kernel doc")
289f5a7200 ("drm/i915/uapi: convert drm_i915_gem_caching to kernel doc")
4a766ae40e ("drm/i915: Drop the CONTEXT_CLONE API (v2)")
6ff6d61dd2 ("drm/i915: Drop I915_CONTEXT_PARAM_NO_ZEROMAP")
fe4751c3d5 ("drm/i915: Drop I915_CONTEXT_PARAM_RINGSIZE")
577729533c ("drm/i915: Document the Virtual Engine uAPI")
c649432e86 ("drm/i915: Fix busy ioctl commentary")
That doesn't result in any changes to tooling as no new ioctl were
added (at least not perceived by tools/perf/trace/beauty/drm_ioctl.sh).
Addressing this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/drm/i915_drm.h' differs from latest version at 'include/uapi/drm/i915_drm.h'
diff -u tools/include/uapi/drm/i915_drm.h include/uapi/drm/i915_drm.h
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jason Ekstrand <jason@jlekstrand.net>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick the change in:
7957d93bf3 ("block: add ioctl to read the disk sequence number")
It adds a new ioctl, but we are still not using that to generate tables
for 'perf trace', so no changes in tooling.
This silences this perf build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/fs.h' differs from latest version at 'include/uapi/linux/fs.h'
diff -u tools/include/uapi/linux/fs.h include/uapi/linux/fs.h
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Matteo Croce <mcroce@microsoft.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To pick the changes in:
db243b7964 ("net/ipv4/ipv6: Replace one-element arraya with flexible-array members")
2d3e5caf96 ("net/ipv4: Replace one-element array with flexible-array member")
That don't result in any change in tooling, the structs changed remains
with the same layout.
This addresses this build warning:
Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h
Cc: David S. Miller <davem@davemloft.net>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently perf saves a build-id with size but old versions assumes the
size of 20. In case the build-id is less than 20 (like for MD5), it'd
fill the rest with 0s.
I saw a problem when old version of perf record saved a binary in the
build-id cache and new version of perf reads the data. The symbols
should be read from the build-id cache (as the path no longer has the
same binary) but it failed due to mismatch in the build-id.
symsrc__init: build id mismatch for /home/namhyung/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf.
The build-id event in the data has 20 byte build-ids, but it saw a
different size (16) when it reads the build-id of the elf file in the
build-id cache.
$ readelf -n ~/.debug/.build-id/53/e4c2f42a4c61a2d632d92a72afa08f00000000/elf
Displaying notes found in: .note.gnu.build-id
Owner Data size Description
GNU 0x00000010 NT_GNU_BUILD_ID (unique build ID bitstring)
Build ID: 53e4c2f42a4c61a2d632d92a72afa08f
Let's fix this by allowing trailing zeros if the size is different.
Fixes: 39be8d0115 ("perf tools: Pass build_id object to dso__build_id_equal()")
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210910224630.1084877-1-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull io_uring fixes from Jens Axboe:
- Fix an off-by-one in a BUILD_BUG_ON() check. Not a real issue right
now as we have plenty of flags left, but could become one. (Hao)
- Fix lockdep issue introduced in this merge window (me)
- Fix a few issues with the worker creation (me, Pavel, Qiang)
- Fix regression with wq_has_sleeper() for IOPOLL (Pavel)
- Timeout link error propagation fix (Pavel)
* tag 'io_uring-5.15-2021-09-11' of git://git.kernel.dk/linux-block:
io_uring: fix off-by-one in BUILD_BUG_ON check of __REQ_F_LAST_BIT
io_uring: fail links of cancelled timeouts
io-wq: fix memory leak in create_io_worker()
io-wq: fix silly logic error in io_task_work_match()
io_uring: drop ctx->uring_lock before acquiring sqd->lock
io_uring: fix missing mb() before waitqueue_active
io-wq: fix cancellation on create-worker failure
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph:
- fix nvmet command set reporting for passthrough controllers (Adam Manzanares)
- update a MAINTAINERS email address (Chaitanya Kulkarni)
- set QUEUE_FLAG_NOWAIT for nvme-multipth (me)
- handle errors from add_disk() (Luis Chamberlain)
- update the keep alive interval when kato is modified (Tatsuya Sasaki)
- fix a buffer overrun in nvmet_subsys_attr_serial (Hannes Reinecke)
- do not reset transport on data digest errors in nvme-tcp (Daniel Wagner)
- only call synchronize_srcu when clearing current path (Daniel Wagner)
- revalidate paths during rescan (Hannes Reinecke)
- Split out the fs/block_dev into block/fops.c and block/bdev.c, which
has been long overdue. Do this now before -rc1, to avoid annoying
conflicts due to this (Christoph)
- blk-throtl use-after-free fix (Li)
- Improve plug depth for multi-device plugs, greatly increasing md
resync performance (Song)
- blkdev_show() locking fix (Tetsuo)
- n64cart error check fix (Yang)
* tag 'block-5.15-2021-09-11' of git://git.kernel.dk/linux-block:
n64cart: fix return value check in n64cart_probe()
blk-mq: allow 4x BLK_MAX_REQUEST_COUNT at blk_plug for multiple_queues
block: move fs/block_dev.c to block/bdev.c
block: split out operations on block special files
blk-throttle: fix UAF by deleteing timer in blk_throtl_exit()
block: genhd: don't call blkdev_show() with major_names_lock held
nvme: update MAINTAINERS email address
nvme: add error handling support for add_disk()
nvme: only call synchronize_srcu when clearing current path
nvme: update keep alive interval when kato is modified
nvme-tcp: Do not reset transport on data digest errors
nvmet: fixup buffer overrun in nvmet_subsys_attr_serial()
nvmet: return bool from nvmet_passthru_ctrl and nvmet_is_passthru_req
nvmet: looks at the passthrough controller when initializing CAP
nvme: move nvme_multi_css into nvme.h
nvme-multipath: revalidate paths during rescan
nvme-multipath: set QUEUE_FLAG_NOWAIT
Pull libata maintainer update from Jens Axboe:
"Damien agreed to take over maintainership of libata, and he would be a
great candidate for it. Update the MAINTAINERS entry to reflect the
change in maintainer and git tree"
* tag 'libata-5.15-2021-09-11' of git://git.kernel.dk/linux-block:
libata: pass over maintainership to Damien Le Moal
Pull tracing fixes from Steven Rostedt:
"Minor fixes to the processing of the bootconfig tree"
* tag 'trace-v5.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
bootconfig: Rename xbc_node_find_child() to xbc_node_find_subkey()
tracing/boot: Fix to check the histogram control param is a leaf node
tracing/boot: Fix trace_boot_hist_add_array() to check array is value
Pull devicetree fixes from Rob Herring:
- Disable fw_devlinks on x86 DT platforms to fix OLPC
- More replacing oneOf+const with enum on a few new schemas
- Drop unnecessary type references on Xilinx SPI binding schema
* tag 'devicetree-fixes-for-5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
spi: dt-bindings: xilinx: Drop type reference on *-bits properties
dt-bindings: More use 'enum' instead of 'oneOf' plus 'const' entries
of: property: Disable fw_devlink DT support for X86
