Every time EHT Operation element changed, mac80211 will parse it and
extract the valid puncturing bitmap according to the bandwidth.
Current driver only update puncturing bitmap to firmware as vdev
parameter. Which can only meet the needs of AP. But STA will also use
it as peer parameter. If only update as vdev parameter, might cause
firmware crash. QCN9274 is the same.
So update bandwidth and puncturing bitmap as peer parameters once they
changed for STA. Then send them to the firmware by WMI event.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240408083047.22548-1-quic_kangyang@quicinc.com
Currently, in the rx error data path, mac id is extracted from the
last 64bits of MSDU end description tag for each entry received in
the WBM error ring. Then, each entry will be updated into the MSDU
list for further processing. The extracted mac id is valid when a
single MSDU is not fragmented and received in the WBM error ring.
In scenarios where the size of a single MSDU received exceeds the
descriptor buffer size, resulting in fragmented or spillover MSDU
entries into the WBM error ring. In this case, the extracted mac id
from each spillover entry is invalid except the last spillover entry
of the MSDU. This invalid mac id leads to packet rejection.
To address this issue, check if the MSDU continuation flag is set,
then extract the valid mac id from the last spillover entry.
Propagate the valid mac id to all the spillover entries of the single
MSDU in the temporary MSDU list(scatter_msdu_list). Then, update this
into the MSDU list (msdu_list) for further processing.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <quic_nithp@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240404141538.1277258-1-quic_nithp@quicinc.com
The radio for which the survey info needs to be collected
depends on the channel idx which could be based on the band.
Use the idx to identify the appropriate sband since multiple
bands could be combined for single wiphy case.
Also use the channel idx and sband to identify the corresponding
radio on which the survey results needs to be populated.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-13-quic_ramess@quicinc.com
Since multiple radios are abstracted under a single wiphy,
apply the rts threshold value to all the vdevs of the radios
combined under single wiphy.
This also implies that vif specific rts threshold support
needs to be added in future from cfg80211/mac80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-12-quic_ramess@quicinc.com
As multiple radios are combined into a single wiphy, and
the current infrastructure supports only set/get antenna
for the wiphy, the max Tx/Rx antenna capability is advertised
during wiphy register.
Hence, When antenna set/get is received we adjust the set/get
based on max radio capability and set/get antenna accordingly.
Multi radio capability needs to introduced with interface
combination changes to support single wiphy model in cfg80211
which would help extend the wiphy specific get/set configs similar
to this to per hw level.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-11-quic_ramess@quicinc.com
With all the radios being combined and registered as a single
mac80211 hw/wiphy, separate regd built from firmware rules need
not be updated to cfg80211. Rather we can pick one of the regd
built from the rules to update to cfg80211 for the whole
registered device. We prefer 6 GHz pdev based rules since it has
the rules for all bands. If the hw doesn't support 6 GHz, then update
rules from one of the pdevs.
Also, when regulatory notification is received, update to all the
underlying radios/ar so that it becomes aware of the change and as
well us it updates its local regd with the new country rules. Later
pick the appropriate pdev's regd(6 GHz if available) and apply to
cfg80211.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-10-quic_ramess@quicinc.com
Since vif and sta objects of different radios are added to same
local hw list in mac80211, additional checks need to be done
in driver to ensure we are processing the intended vif
and sta corresponding to the radio when the vif and sta mac80211
iterator utils are used from driver.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-9-quic_ramess@quicinc.com
Since the vdev create for a corresponding vif is deferred
until a channel is assigned, cache the information which
are received through mac80211 ops between add_interface()
and assign_vif_chanctx() and set them once the vdev is
created on one of the ath12k radios as the channel gets
assigned via assign_vif_chanctx().
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-8-quic_ramess@quicinc.com
For ops which passes the vif info, fetch the radio(ar)
to be used for corresponding functions based on the
the vdev creation status. If the vdev is not created yet,
which could happen when the ops are called before channel
is assigned for the vif, the data needs to be cached and this
is done in followup changes.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-7-quic_ramess@quicinc.com
When multiple radios are advertised as a single wiphy which
supports various bands, a default scan request to mac80211
from cfg80211 will split the driver request based on band,
so each request will have channels belonging to the same band.
With this supported by default, the ath12k driver on receiving
this request checks for one of the channels in the request and
selects the corresponding radio(ar) on which the scan is going
to be performed and creates a vdev on that radio.
Note that on scan completion this vdev is not deleted. If a new
scan request is seen on that same vif for a different band the
vdev will be deleted and created on the new radio supporting the
request. The vdev delete logic is refactored to have this done
dynamically.
The reason for not deleting the vdev on scan stop is to avoid
repeated delete-create sequence if the scan is on the same band.
Also, during channel assign, new vdev creation can be optimized
as well.
Also if the scan is requested when the vdev is in started state,
no switching to new radio is allowed and scan on channels only
within same radio is allowed.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-6-quic_ramess@quicinc.com
With single wiphy, multiple radios are combined into a single wiphy.
Since any channel can be assigned to a vif being brought up,
the vdev cannot be created during add_interface(). Hence defer the
vdev creation till channel assignment.
If only one radio is part of the wiphy, then the existing logic
is maintained, i.e vdevs are created during add interface and
started during channel assignment. This ensures no functional changes
to single pdev devices which has only one radio in the SoC.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-5-quic_ramess@quicinc.com
Modify add and remove chanctx mac80211 ops to fetch the correct
radio(ar) based on channel context.
This change also introduces new helper function to fetch the
radio/ar based on channel context and ieee80211_chan which internally
uses the radio's low/high freq range.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-3-quic_ramess@quicinc.com
Currently MAC HW un/register helper function support the single radio.
To enable single/multi link operation in the future, the following helper
functions need to be refactored to accommodate multiple radios under a
single MAC HW un/register:
* ath12k_ah_to_ar()
* ath12k_mac_hw_allocate()
* ath12k_mac_hw_register()
* ath12k_mac_hw_unregister()
This refactoring will make it easier to scale these functionalities and
support Multi link operation.
Current Multi wiphy Model
+---------------+ +---------------+ +---------------+
| Mac80211 hw | | Mac80211 hw | | Mac80211 hw |
| private data | | private data | | private data |
| | | | | |
|ath12k_hw (ah) | |ath12k_hw (ah) | |ath12k_hw (ah) |
| | | | | |
| +-----------+ | | +-----------+ | | +-----------+ |
| | ar (2GHz) | | | | ar (5GHz) | | | | ar (6GHz) | |
| +-----------+ | | +-----------+ | | +-----------+ |
| | | | | |
+---------------+ +---------------+ +---------------+
Single wiphy Model
+--------------+
| Mac80211 hw |
| private data |
| |
|ath12k hw (ah)|
| +----------+ |
| |ar (2GHz) | |
| +----------+ |
| |ar (5GHz) | |
| +----------+ |
| |ar (6GHz) | |
| +----------+ |
+--------------+
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240405194519.1337906-2-quic_ramess@quicinc.com
Now that all infrastructure is in place and ath11k is fixed to handle all the
corner cases, power down the ath11k firmware during suspend and power it back
up during resume. This fixes the problem when using hibernation with ath11k PCI
devices.
For suspend, two conditions needs to be satisfied:
1. since MHI channel unprepare would be done in late suspend stage,
ath11k needs to get all QMI-dependent things done before that stage.
2. and because unprepare MHI channels requires a working MHI stack,
ath11k is not allowed to call mhi_power_down() until that finishes.
So the original suspend callback is separated into two parts: the first part
handles all QMI-dependent things in suspend callback; while the second part
powers down MHI in suspend_late callback. This is valid because kernel calls
ath11k's suspend callback before all suspend_late callbacks, making the first
condition happy. And because MHI devices are children of ath11k device
(ab->dev), kernel guarantees that ath11k's suspend_late callback is called
after QRTR's suspend_late callback, this satisfies the second condition.
Above analysis also applies to resume process. so the original resume
callback is separated into two parts: the first part powers up MHI stack
in resume_early callback, this guarantees MHI stack is working when
QRTR tries to prepare MHI channels (kernel calls QRTR's resume_early callback
after ath11k's resume_early callback, due to the child-father relationship);
the second part waits for the completion of restart, which won't fail now
since MHI channels are ready for use by QMI.
Another notable change is in power down path, we tell mhi_power_down() to not
to destroy MHI devices, making it possible for QRTR to help unprepare/prepare
MHI channels, and finally get us rid of the probe-defer issue when resume.
Also change related code due to interface changes.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240305021320.3367-4-quic_bqiang@quicinc.com
MHI devices may not be destroyed during suspend/hibernation, so need
to unprepare/prepare MHI channels throughout the transition, this is
done by adding suspend/resume callbacks.
The suspend callback is called in the late suspend stage, this means
MHI channels are still alive at suspend stage, and that makes it
possible for an MHI controller driver to communicate with others over
those channels at suspend stage. While the resume callback is called
in the early resume stage, for a similar reason.
Also note that we won't do unprepare/prepare when MHI device is in
suspend state because it's pointless if MHI is only meant to go through
a suspend/resume transition, instead of a complete power cycle.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240305021320.3367-3-quic_bqiang@quicinc.com
By default driver supports intra-device SLO/MLO, the link capability flags
reflect this. When the QMI PHY capability learning fails driver not enable
the MLO parameter in the host capability QMI request message. In this case,
reset the device link capability flags to zero (SLO/MLO not support) to
accurately represent the capabilities.
Found in code review.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240403042056.1504209-3-quic_periyasa@quicinc.com
Link capability categorized as Single Link Operation (SLO) and Multi Link
Operation (MLO).
- Intra-device SLO/MLO refers to links present within a device
- Inter-device SLO/MLO refers to links present across multiple devices
Currently, driver uses a boolean variable to represent intra-device SLO/MLO
capability. To accommodate inter-device SLO/MLO capabilities within the
same variable, modify the existing variable name and type. Define a new
enumeration for the link capabilities to accommodate both intra-device
and inter-device scenarios. Populate the enum based on the supported
capabilities.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240403042056.1504209-2-quic_periyasa@quicinc.com
Different Qualcomm platforms using WCN3990 WiFI chip use SoC-specific
firmware versions with different features. For example firmware for
SDM845 doesn't use single-chan-info-per-channel feature, while firmware
for QRB2210 / QRB4210 requires that feature. Allow board DT files to
override the subdir of the fw dir used to lookup the firmware-N.bin file
decribing corresponding WiFi firmware.
For example:
- ath10k/WCN3990/hw1.0/wlanmdsp.mbn,
ath10k/WCN3990/hw1.0/firmware-5.bin: main firmware files, used by default
- ath10k/WCN3990/hw1.0/qcm2290/wlanmdsp.mbn,
ath10k/WCN3990/hw1.0/qcm2290/firmware-5.bin: SoC specific firmware
with different signature and feature bits
Note, while board files lookup uses the same function and thus it is
possible to provide board-specific board-2.bin files, this is not
required in 99% of cases as board-2.bin already contains a way to
provide board-specific data with finer granularity than DT overrides.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240306-wcn3990-firmware-path-v2-2-f89e98e71a57@linaro.org
This driver's initialization functions do not perform any custom code,
except printing messages. Printing messages on modules
loading/unloading is discouraged because it pollutes the dmesg
regardless whether user actually has this device. Core kernel code
already gives tools to investigate whether module was loaded or not.
Drop the printing messages which allows to replace open-coded
module_sdio_driver().
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240329171019.63836-2-krzysztof.kozlowski@linaro.org
Prepare for the coming implementation by GCC and Clang of the
__counted_by attribute. Flexible array members annotated with
__counted_by can have their accesses bounds-checked at run-time
via CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE
(for strcpy/memcpy-family functions).
Also, -Wflex-array-member-not-at-end is coming in GCC-14, and we are
getting ready to enable it globally.
So, use the `DEFINE_FLEX()` helper for an on-stack definition of
a flexible structure where the size of the flexible-array member
is known at compile-time, and refactor the rest of the code,
accordingly.
So, with these changes, fix the following warning:
drivers/net/wireless/ath/wil6210/wmi.c:4018:49: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Link: https://github.com/KSPP/linux/issues/202
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/ZgSTCmdP+omePvWg@neat
Prepare for the coming implementation by GCC and Clang of the
__counted_by attribute. Flexible array members annotated with
__counted_by can have their accesses bounds-checked at run-time
via CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE
(for strcpy/memcpy-family functions).
Also, -Wflex-array-member-not-at-end is coming in GCC-14, and we are
getting ready to enable it globally.
So, use the `DEFINE_FLEX()` helper for an on-stack definition of
a flexible structure where the size of the flexible-array member
is known at compile-time, and refactor the rest of the code,
accordingly.
So, with these changes, fix the following warning:
drivers/net/wireless/ath/wil6210/cfg80211.c:896:43: warning: structure containing a flexible array member is not at the end of another structure [-Wflex-array-member-not-at-end]
Link: https://github.com/KSPP/linux/issues/202
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/ZgSP/CMSVfr68R2u@neat
gcc-9 and some other older versions produce a false-positive warning
for zeroing two fields
In file included from include/linux/string.h:369,
from drivers/net/wireless/ath/ath9k/main.c:18:
In function 'fortify_memset_chk',
inlined from 'ath9k_ps_wakeup' at drivers/net/wireless/ath/ath9k/main.c:140:3:
include/linux/fortify-string.h:462:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
462 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Using a struct_group seems to reliably avoid the warning and
not make the code much uglier. The combined memset() should even
save a couple of cpu cycles.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240328135509.3755090-3-arnd@kernel.org
The carl9170_tx_release() function sometimes triggers a fortified-memset
warning in my randconfig builds:
In file included from include/linux/string.h:254,
from drivers/net/wireless/ath/carl9170/tx.c:40:
In function 'fortify_memset_chk',
inlined from 'carl9170_tx_release' at drivers/net/wireless/ath/carl9170/tx.c:283:2,
inlined from 'kref_put' at include/linux/kref.h:65:3,
inlined from 'carl9170_tx_put_skb' at drivers/net/wireless/ath/carl9170/tx.c:342:9:
include/linux/fortify-string.h:493:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
493 | __write_overflow_field(p_size_field, size);
Kees previously tried to avoid this by using memset_after(), but it seems
this does not fully address the problem. I noticed that the memset_after()
here is done on a different part of the union (status) than the original
cast was from (rate_driver_data), which may confuse the compiler.
Unfortunately, the memset_after() trick does not work on driver_rates[]
because that is part of an anonymous struct, and I could not get
struct_group() to do this either. Using two separate memset() calls
on the two members does address the warning though.
Fixes: fb5f6a0e80 ("mac80211: Use memset_after() to clear tx status")
Link: https://lore.kernel.org/lkml/20230623152443.2296825-1-arnd@kernel.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240328135509.3755090-2-arnd@kernel.org
The initial debugfs infra bringup in ath12k driver and create the ath12k debugfs
and soc-specific directories in /sys/kernel/debug/
For each ath12k device, directory will be created in <bus>-<devname>
schema under ath12k root directory.
Example with one ath12k device:
/sys/kernel/debug/ath12k/pci-0000:06:00.0
ath12k
`-- pci-0000:06:00.0
|-- mac0
To enable ath12k debugfs support (CONFIG_ATH12K_DEBUGFS=y)
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240320171305.655288-2-quic_rgnanase@quicinc.com
Petr Machata says:
====================
mlxsw: Preparations for improving performance
Amit Cohen writes:
mlxsw driver will use NAPI for event processing in a next patch set.
Some additional improvements will be added later. This patch set
prepares the code for NAPI usage and refactor some relevant areas. See
more details in commit messages.
Patch Set overview:
Patches #1-#2 are preparations for patch #3
Patch #3 setups tasklets as part of queue initializtion
Patch #4 removes handling of unlikely scenario
Patch #5 removes unused counters
Patch #6 makes style change in mlxsw_pci_eq_tasklet()
Patch #7-#10 poll command interface instead of EQ0 usage
Patches #11-#12 make style change and break the function
mlxsw_pci_cq_tasklet()
Patches #13-#14 remove functions which can be replaced by a stored value
Patch #15 improves accessing to descriptor queue instance
====================
Link: https://lore.kernel.org/r/cover.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, for each completion, we check the number of descriptor queue
and take it via mlxsw_pci_{sdq,rdq}_get(). This is inefficient, the
DQ should be the same for all the completions in CQ, as each CQ handles
only one DQ - SDQ or RDQ. This mapping is handled as part of DQ
initialization via mlxsw_cmd_mbox_sw2hw_dq_cq_set().
Instead, as part of DQ initialization, set DQ pointer in the appropriate
CQ structure. When we handle completions, warn in case that the DQ number
that we expect is different from the number we get in the CQE. Call
WARN_ON_ONCE() only after checking the value, to avoid calling this method
for each completion.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/a5b2559cd6d532c120f3194f89a1e257110318f1.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The number of SDQs is stored as part of 'mlxsw_pci' structure. In some
cases, the driver uses this value and in some cases it calls
mlxsw_pci_sdq_count() to get the value. Align the code to use the
stored value. This simplifies the code and makes it clearer that the
value is always the same. Rename 'mlxsw_pci->num_sdq_cqs' to
'mlxsw_pci->num_sdqs' as now it is used not only in CQ context.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/0c8788506d9af35d589dbf64be35a508fd63d681.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Completion queues are used for completions of RDQ or SDQ. Each
completion queue is used for one DQ. The first CQs are used for SDQs and
the rest are used for RDQs.
Currently, for each CQE (completion queue element), we check 'sr' value
(send/receive) to know if it is completion of RDQ or SDQ. Actually, we
do not really have to check it, as according to the queue number we know
if it handles completions of Rx or Tx.
Break the tasklet into two - one for Rx (RDQ) and one for Tx (SDQ). Then,
setup the appropriate tasklet for each queue as part of queue
initialization. Use 'sr' value for unlikely case that we get completion
with type that we do not expect. Call WARN_ON_ONCE() only after checking
the value, to avoid calling this method for each completion.
A next patch set will use NAPI to handle events, then we will have a
separate poll method for Rx and Tx. This change is a preparation for
NAPI usage.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/50fbc366f8de54cb5dc72a7c4f394333ef71f1d0.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The device supports two event queues. EQ0 is used for command interface
completion events. EQ1 is used for completion events of RDQ or SDQ.
Currently, for each EQE (event queue element), we check the queue number
and handle accordingly. More than that, for each interrupt we schedule
tasklets for both EQs. This is really ineffective, especially because of
the fact that EQ0 is used only as part of driver init/fini, when EMADs are
not available. There is no point to schedule the tasklet for it and check
each EQE.
A previous patch changed the code to poll command interface for each use of
it. It means that now there is no real reason to use EQ0, as we poll the
command interface.
Initialize only one event queue and use it as EQ1 (this is determined by
queue number). Then, for each interrupt we can schedule the tasklet only
for one queue and we do not have to check the queue number. This
simplifies the code and should improve performance. Note that polling
command interface is ok as we use it only as part of driver init/fini.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/23d764f5c032e4c363b98590b746a4b32d2bf900.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Command interface is used for configuring and querying FW when EMADs are
not available. During the time that the driver sets up the asynchronous
queues, it polls the command interface for getting completions. Then,
there is a short period when asynchronous queues work, but EMADs are not
available (marked in the code as nopoll = true). During this time, we
send commands via command interface, but we do not poll it, as we can get
an interrupt for the completion. Completions of command interface are
received from HW in EQ0 (event queue 0).
The usage of EQ0 instead of polling is done only 4 times during
initialization and one time during tear down, but it makes an overhead
during lifetime of the driver. For each interrupt, we have to check if
we get events in EQ0 or EQ1 and handle them. This is really ineffective,
especially because of the fact that EQ0 is used only as part of driver
init/fini.
Instead, we can poll command interface for each call of cmd_exec(). It
means that when we send a command via command interface (as EMADs are
not available), we will poll it, regardless of availability of the
asynchronous queues. This will allow us to configure later only EQ1 and
simplify the flow.
Remove 'nopoll' indication and change mlxsw_pci_cmd_exec() to poll till
answer/timeout regardless of queues' state. For now, completions are
handled also by EQ0, but it will be removed in next patch. Additional
cleanups will be added in next patches.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/e674c70380ceda953e0e45a77334c5d22e69938f.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The structure 'mlxsw_pci_queue' stores several counters which were consumed
via debugfs. Since commit 9a32562bec ("mlxsw: Remove debugfs interface"),
these counters are not used. Remove them. This makes the 'union u' and
'struct eq' redundant. Maintain 'struct cq' as it will be extended later.
Replace increasing 'q->u.eq.ev_other_count' with WARN_ON_ONCE(), as it is
used in an unreasonable case of receiving event in EQ which is not EQ0 or
EQ1. When the queues are initialized, we check number of event queues and
fail with the print "Unsupported number of queues" in case that the driver
tries to initialize more than two queues.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/ee9e658800aa0390e08342100bc27daff4c176c0.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, as part of mlxsw_pci_cq_tasklet(), we check if any item
was handled, and only in such case we arm doorbell. This is unlikely case,
as we schedule tasklet only for CQs that we get an event for them, which
means that they contain completions to handle. Remove this check, which
is supposed to be true always, and even if it is false, it is not a mistake
to ring the doorbell. We can warn on such case, but it is not really worth
to add a check which will be run for each CQ handling when we do not expect
to reach it and it does not point to logic error that should be handled.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/f8efa481bfe7bebb9f93bb803f44ab7da77f53e6.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the structure 'mlxsw_pci_queue_ops' holds a pointer to the
callback function of tasklet. This is used only for EQ and CQ. mlxsw
driver will use NAPI in a following patch set, so CQ will not use tasklet
anymore. As preparation, remove this pointer from the shared operation
structure and setup the tasklet as part of queue initialization.
For now, setup tasklet for EQ and CQ. Later, CQ code will be changed.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/a326cae5fc1ad085a1a063c004983de6fe389414.1712062203.git.petrm@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tariq Toukan says:
====================
mlx5 misc patches
This patchset includes small features and misc code enhancements for the
mlx5 core and EN drivers.
Patches 1-4 by Gal improves the mlx5e ethtool stats implementation, for
example by using standard helpers ethtool_sprintf/puts.
Patch 5 by me adds a reset option for the FW command interface debugfs
stats entries. This allows explicit FW command interface stats reset
between different runs of a test case.
Patches 6 and 7 are simple cleanups.
Patch 8 by Gal adds driver support for 800Gbps link modes.
Patch 9 by Jianbo enhances the L4 steering abilities.
Patches 10-11 by Jianbo save redundant operations.
====================
Link: https://lore.kernel.org/r/20240402133043.56322-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
