Add wakeup from suspend for WoM when enabled and put accel in low-power
mode when suspended. Requires rewriting pwr_mgmt_1 register handling and
factorize out accel LPF settings. Use a low-power rate similar to the chip
sampling rate but always lower for a best match of the sampling rate while
saving power and adjust threshold to follow the required roc value.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20240311160557.437337-5-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
WoM is a threshold test on accel value comparing actual sample with
previous one. It maps best to roc rising event.
Add support of a new WOM sensor and functions for handling the associated
roc_rising event. The event value is in SI units. Ensure WOM is stopped and
restarted at suspend-resume, handle usage with buffer data ready interrupt,
and handle change in sampling rate impacting already set roc value.
Signed-off-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20240311160557.437337-2-inv.git-commit@tdk.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The HDC3020 provides an active low reset signal that must be handled if
connected. Asserting this signal turns the device into Trigger-on Demand
measurement mode, reducing its power consumption when no measurements
are required like in low-power modes.
According to the datasheet, the longest "Reset Ready" is 3 ms, which is
only taken into account if the reset signal is defined.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240303-hdc3020-pm-v3-3-48bc02b5241b@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The HDC3020 sensor carries out periodic measurements during normal
operation, but as long as the power supply is enabled, it will carry on
in low-power modes. In order to avoid that and reduce power consumption,
the device can be switched to Trigger-on Demand mode, and if possible,
turn off its regulator.
According to the datasheet, the maximum "Power Up Ready" is 5 ms.
Add resume/suspend pm operations to manage measurement mode and
regulator state.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20240303-hdc3020-pm-v3-1-48bc02b5241b@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver support for Avago (Broadcom) APDS9306 Ambient Light Sensor.
It has two channels - ALS and CLEAR. The ALS (Ambient Light Sensor)
channel approximates the response of the human-eye providing direct
read out where the output count is proportional to ambient light levels.
It is internally temperature compensated and rejects 50Hz and 60Hz flicker
caused by artificial light sources. Hardware interrupt configuration is
optional. It is a low power device with 20 bit resolution and has
configurable adaptive interrupt mode and interrupt persistence mode.
The device also features inbuilt hardware gain, multiple integration time
selection options and sampling frequency selection options.
This driver also uses the IIO GTS (Gain Time Scale) Helpers Namespace for
Scales, Gains and Integration time implementation.
Signed-off-by: Subhajit Ghosh <subhajit.ghosh@tweaklogic.com>
Link: https://lore.kernel.org/r/20240309105031.10313-6-subhajit.ghosh@tweaklogic.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7173 family offer a complete integrated Sigma-Delta ADC solution
which can be used in high precision, low noise single channel
applications or higher speed multiplexed applications. The Sigma-Delta
ADC is intended primarily for measurement of signals close to DC but also
delivers outstanding performance with input bandwidths out to ~10kHz.
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Michael Walle <michael@walle.cc> # for gpio-regmap
Signed-off-by: Dumitru Ceclan <mitrutzceclan@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240228110622.25114-3-mitrutzceclan@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The AD7173 family offer a complete integrated Sigma-Delta ADC solution
which can be used in high precision, low noise single channel applications
or higher speed multiplexed applications. The Sigma-Delta ADC is intended
primarily for measurement of signals close to DC but also delivers
outstanding performance with input bandwidths out to ~10kHz.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Dumitru Ceclan <mitrutzceclan@gmail.com>
Link: https://lore.kernel.org/r/20240228110622.25114-1-mitrutzceclan@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This use of the new cleanup.h scope based freeing infrastructure allows
us to exit directly from error conditions and in the good path with
the reference obtained from fwnode_find_reference() (which may be an error
pointer) automatically released.
Similarly the _scoped() version of device_for_each_child_node()
removes the need for the manual calling of fwnode_handl_put() in
paths where the code exits the loop early.
Tidy up some unusual indentation in a dev_dbg() whilst here.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240224123215.161469-2-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Switching to the _scoped() version removes the need for manual
calling of fwnode_handle_put() in the paths where the code
exits the loop early. In this case that's all in error paths.
The use of fwnode_for_each_available_child_node() here is assumed
to have been down to a false assumption that device_for_each_child_node()
doesn't check avaialble - so this transition to the scoped
device_for_each_child_node_scoped() is equivalent.
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240217164249.921878-13-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Similar to recently propose for_each_child_of_node_scoped() this
new version of the loop macro instantiates a new local
struct fwnode_handle * that uses the __free(fwnode_handle) auto
cleanup handling so that if a reference to a node is held on early
exit from the loop the reference will be released. If the loop
runs to completion, the child pointer will be NULL and no action will
be taken.
The reason this is useful is that it removes the need for
fwnode_handle_put() on early loop exits. If there is a need
to retain the reference, then return_ptr(child) or no_free_ptr(child)
may be used to safely disable the auto cleanup.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Link: https://lore.kernel.org/r/20240217164249.921878-5-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull EFI fixes from Ard Biesheuvel:
- Fix logic that is supposed to prevent placement of the kernel image
below LOAD_PHYSICAL_ADDR
- Use the firmware stack in the EFI stub when running in mixed mode
- Clear BSS only once when using mixed mode
- Check efi.get_variable() function pointer for NULL before trying to
call it
* tag 'efi-fixes-for-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi:
efi: fix panic in kdump kernel
x86/efistub: Don't clear BSS twice in mixed mode
x86/efistub: Call mixed mode boot services on the firmware's stack
efi/libstub: fix efi_random_alloc() to allocate memory at alloc_min or higher address
