The Radxa ROCK 5B+/5T USB Type-C port supports Dual Role Data and
should also act as a host. However, currently, when acting as a host,
only self-powered devices work.
Since the ROCK 5B+ supports Dual Role Power, set the power-role
property to "dual" and the try-power-role property to "sink". (along
with related properties)
The ROCK 5T should only support the "source" power-role.
This allows the port to act as a host, supply power to the port, and
allow bus-powered devices to work.
Note that on the ROCK 5T, with this patch applied, it has been
observed that some bus-powered devices do not work correctly. Also,
it has been observed that after connecting a device (and the data-role
switches to host), connecting a host device does not switch the
data-role back to the device role. These issues should be addressed
separately.
Note that there is a separate known issue where USB 3.0 SuperSpeed
devices do not work when oriented in reverse. This issue should also be
addressed separately. (USB 2.0/1.1 devices work in both orientations)
Fixes: 67b2c15d8f ("arm64: dts: rockchip: add USB-C support for ROCK 5B/5B+/5T")
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://patch.msgid.link/20251104085227.820-1-naoki@radxa.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When the device was first added, there was a problem with the bluetooth
controller that manifested when DMA was enabled for the underlying UART
interface. At some point in the intervening time the problem appears to
have been resolved. Add the UART rx and tx channels back to re-enable
UART.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://patch.msgid.link/20251105205708.732125-6-macroalpha82@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3588 evb2 board has a full size DisplayPort connector, enable
for it.
Signed-off-by: Chaoyi Chen <chaoyi.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NanoPi R76S (as "R76S") is an open-sourced mini IoT gateway
device with two 2.5G, designed and developed by FriendlyElec.
Specification:
- Rockchip RK3576
- 2/4GB LPDDR4X RAM
- 2x 2500Base-T (PCIe, rtl8125b)
- 3x LEDs (Power, LAN, WAN)
- 32GB eMMC
- MicroSD Slot
- MDMI 1.4/2.0 OUT
- M.2 E-Key SDIO slot
- USB 3.0 Port
- USB Type-C 5V Power
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NanoPi R76S (as "R76S") is an open-sourced mini IoT gateway
device with two 2.5G, designed and developed by FriendlyElec.
Add devicetree binding documentation for the FriendlyElec NanoPi R76S
board.
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the Designware MIPI DSI controller and it's port nodes.
Signed-off-by: WeiHao Li <cn.liweihao@gmail.com>
[removed endpoint address, as there is only one vop leading to DSI]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK3368 has a InnoSilicon D-PHY which supports DSI/LVDS/TTL with maximum
trasnfer rate of 1 Gbps per lane.
Signed-off-by: WeiHao Li <cn.liweihao@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Pull i2c fix from Wolfram Sang:
"One revert because of a regression in the I2C core which has sadly not
showed up during its time in -next"
* tag 'i2c-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: boardinfo: Annotate code used in init phase only"
Pull irq fixes from Borislav Petkov:
- Skip interrupt ID 0 in sifive-plic during suspend/resume because
ID 0 is reserved and accessing reserved register space could result
in undefined behavior
- Fix a function's retval check in aspeed-scu-ic
* tag 'irq_urgent_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/sifive-plic: Avoid interrupt ID 0 handling during suspend/resume
irqchip/aspeed-scu-ic: Fix an IS_ERR() vs NULL check
Pull tracing fixes from Steven Rostedt:
"The previous fix to trace_marker required updating trace_marker_raw as
well. The difference between trace_marker_raw from trace_marker is
that the raw version is for applications to write binary structures
directly into the ring buffer instead of writing ASCII strings. This
is for applications that will read the raw data from the ring buffer
and get the data structures directly. It's a bit quicker than using
the ASCII version.
Unfortunately, it appears that our test suite has several tests that
test writes to the trace_marker file, but lacks any tests to the
trace_marker_raw file (this needs to be remedied). Two issues came
about the update to the trace_marker_raw file that syzbot found:
- Fix tracing_mark_raw_write() to use per CPU buffer
The fix to use the per CPU buffer to copy from user space was
needed for both the trace_maker and trace_maker_raw file.
The fix for reading from user space into per CPU buffers properly
fixed the trace_marker write function, but the trace_marker_raw
file wasn't fixed properly. The user space data was correctly
written into the per CPU buffer, but the code that wrote into the
ring buffer still used the user space pointer and not the per CPU
buffer that had the user space data already written.
- Stop the fortify string warning from writing into trace_marker_raw
After converting the copy_from_user_nofault() into a memcpy(),
another issue appeared. As writes to the trace_marker_raw expects
binary data, the first entry is a 4 byte identifier. The entry
structure is defined as:
struct {
struct trace_entry ent;
int id;
char buf[];
};
The size of this structure is reserved on the ring buffer with:
size = sizeof(*entry) + cnt;
Then it is copied from the buffer into the ring buffer with:
memcpy(&entry->id, buf, cnt);
This use to be a copy_from_user_nofault(), but now converting it to
a memcpy() triggers the fortify-string code, and causes a warning.
The allocated space is actually more than what is copied, as the
cnt used also includes the entry->id portion. Allocating
sizeof(*entry) plus cnt is actually allocating 4 bytes more than
what is needed.
Change the size function to:
size = struct_size(entry, buf, cnt - sizeof(entry->id));
And update the memcpy() to unsafe_memcpy()"
* tag 'trace-v6.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: Stop fortify-string from warning in tracing_mark_raw_write()
tracing: Fix tracing_mark_raw_write() to use buf and not ubuf
Pull Kbuild fixes from Nathan Chancellor:
- Fix UAPI types check in headers_check.pl
- Only enable -Werror for hostprogs with CONFIG_WERROR / W=e
- Ignore fsync() error when output of gen_init_cpio is a pipe
- Several little build fixes for recent modules.builtin.modinfo series
* tag 'kbuild-fixes-6.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kbuild/linux:
kbuild: Use '--strip-unneeded-symbol' for removing module device table symbols
s390/vmlinux.lds.S: Move .vmlinux.info to end of allocatable sections
kbuild: Add '.rel.*' strip pattern for vmlinux
kbuild: Restore pattern to avoid stripping .rela.dyn from vmlinux
gen_init_cpio: Ignore fsync() returning EINVAL on pipes
scripts/Makefile.extrawarn: Respect CONFIG_WERROR / W=e for hostprogs
kbuild: uapi: Strip comments before size type check
Pull SCSI fixes from James Bottomley:
"Fixes only in drivers (ufs, mvsas, qla2xxx, target) that came in just
before or during the merge window.
The most important one is the qla2xxx which reverts a conversion to
fix flexible array member warnings, that went up in this merge window
but which turned out on further testing to be causing data corruption"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: core: Include UTP error in INT_FATAL_ERRORS
scsi: ufs: sysfs: Make HID attributes visible
scsi: mvsas: Fix use-after-free bugs in mvs_work_queue
scsi: ufs: core: Fix PM QoS mutex initialization
scsi: ufs: core: Fix runtime suspend error deadlock
Revert "scsi: qla2xxx: Fix memcpy() field-spanning write issue"
scsi: target: target_core_configfs: Add length check to avoid buffer overflow
Pull more x86 updates from Borislav Petkov:
- Remove a bunch of asm implementing condition flags testing in KVM's
emulator in favor of int3_emulate_jcc() which is written in C
- Replace KVM fastops with C-based stubs which avoids problems with the
fastop infra related to latter not adhering to the C ABI due to their
special calling convention and, more importantly, bypassing compiler
control-flow integrity checking because they're written in asm
- Remove wrongly used static branches and other ugliness accumulated
over time in hyperv's hypercall implementation with a proper static
function call to the correct hypervisor call variant
- Add some fixes and modifications to allow running FRED-enabled
kernels in KVM even on non-FRED hardware
- Add kCFI improvements like validating indirect calls and prepare for
enabling kCFI with GCC. Add cmdline params documentation and other
code cleanups
- Use the single-byte 0xd6 insn as the official #UD single-byte
undefined opcode instruction as agreed upon by both x86 vendors
- Other smaller cleanups and touchups all over the place
* tag 'x86_core_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
x86,retpoline: Optimize patch_retpoline()
x86,ibt: Use UDB instead of 0xEA
x86/cfi: Remove __noinitretpoline and __noretpoline
x86/cfi: Add "debug" option to "cfi=" bootparam
x86/cfi: Standardize on common "CFI:" prefix for CFI reports
x86/cfi: Document the "cfi=" bootparam options
x86/traps: Clarify KCFI instruction layout
compiler_types.h: Move __nocfi out of compiler-specific header
objtool: Validate kCFI calls
x86/fred: KVM: VMX: Always use FRED for IRQs when CONFIG_X86_FRED=y
x86/fred: Play nice with invoking asm_fred_entry_from_kvm() on non-FRED hardware
x86/fred: Install system vector handlers even if FRED isn't fully enabled
x86/hyperv: Use direct call to hypercall-page
x86/hyperv: Clean up hv_do_hypercall()
KVM: x86: Remove fastops
KVM: x86: Convert em_salc() to C
KVM: x86: Introduce EM_ASM_3WCL
KVM: x86: Introduce EM_ASM_1SRC2
KVM: x86: Introduce EM_ASM_2CL
KVM: x86: Introduce EM_ASM_2W
...
Pull x86 cleanups from Borislav Petkov:
- Simplify inline asm flag output operands now that the minimum
compiler version supports the =@ccCOND syntax
- Remove a bunch of AS_* Kconfig symbols which detect assembler support
for various instruction mnemonics now that the minimum assembler
version supports them all
- The usual cleanups all over the place
* tag 'x86_cleanups_for_v6.18_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Remove code depending on __GCC_ASM_FLAG_OUTPUTS__
x86/sgx: Use ENCLS mnemonic in <kernel/cpu/sgx/encls.h>
x86/mtrr: Remove license boilerplate text with bad FSF address
x86/asm: Use RDPKRU and WRPKRU mnemonics in <asm/special_insns.h>
x86/idle: Use MONITORX and MWAITX mnemonics in <asm/mwait.h>
x86/entry/fred: Push __KERNEL_CS directly
x86/kconfig: Remove CONFIG_AS_AVX512
crypto: x86 - Remove CONFIG_AS_VPCLMULQDQ
crypto: X86 - Remove CONFIG_AS_VAES
crypto: x86 - Remove CONFIG_AS_GFNI
x86/kconfig: Drop unused and needless config X86_64_SMP
Pull slab fix from Vlastimil Babka:
"A NULL pointer deref hotfix"
* tag 'slab-for-6.18-rc1-hotfix' of git://git.kernel.org/pub/scm/linux/kernel/git/vbabka/slab:
slab: fix barn NULL pointer dereference on memoryless nodes
Pull more updates from Andrew Morton:
"Just one series here - Mike Rappoport has taught KEXEC handover to
preserve vmalloc allocations across handover"
* tag 'mm-nonmm-stable-2025-10-10-15-03' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
lib/test_kho: use kho_preserve_vmalloc instead of storing addresses in fdt
kho: add support for preserving vmalloc allocations
kho: replace kho_preserve_phys() with kho_preserve_pages()
kho: check if kho is finalized in __kho_preserve_order()
MAINTAINERS, .mailmap: update Umang's email address
Pull misc fixes from Andrew Morton:
"7 hotfixes. All 7 are cc:stable and all 7 are for MM.
All singletons, please see the changelogs for details"
* tag 'mm-hotfixes-stable-2025-10-10-15-00' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm: hugetlb: avoid soft lockup when mprotect to large memory area
fsnotify: pass correct offset to fsnotify_mmap_perm()
mm/ksm: fix flag-dropping behavior in ksm_madvise
mm/damon/vaddr: do not repeat pte_offset_map_lock() until success
mm/rmap: fix soft-dirty and uffd-wp bit loss when remapping zero-filled mTHP subpage to shared zeropage
mm/thp: fix MTE tag mismatch when replacing zero-filled subpages
memcg: skip cgroup_file_notify if spinning is not allowed
The fix to use a per CPU buffer to read user space tested only the writes
to trace_marker. But it appears that the selftests are missing tests to
the trace_maker_raw file. The trace_maker_raw file is used by applications
that writes data structures and not strings into the file, and the tools
read the raw ring buffer to process the structures it writes.
The fix that reads the per CPU buffers passes the new per CPU buffer to
the trace_marker file writes, but the update to the trace_marker_raw write
read the data from user space into the per CPU buffer, but then still used
then passed the user space address to the function that records the data.
Pass in the per CPU buffer and not the user space address.
TODO: Add a test to better test trace_marker_raw.
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: https://lore.kernel.org/20251011035243.386098147@kernel.org
Fixes: 64cf7d058a ("tracing: Have trace_marker use per-cpu data to read user space")
Reported-by: syzbot+9a2ede1643175f350105@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/68e973f5.050a0220.1186a4.0010.GAE@google.com/
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
After commit 5ab23c7923 ("modpost: Create modalias for builtin
modules"), relocatable RISC-V kernels with CONFIG_KASAN=y start failing
when attempting to strip the module device table symbols:
riscv64-linux-objcopy: not stripping symbol `__mod_device_table__kmod_irq_starfive_jh8100_intc__of__starfive_intc_irqchip_match_table' because it is named in a relocation
make[4]: *** [scripts/Makefile.vmlinux:97: vmlinux] Error 1
The relocation appears to come from .LASANLOC5 in .data.rel.local:
$ llvm-objdump --disassemble-symbols=.LASANLOC5 --disassemble-all -r drivers/irqchip/irq-starfive-jh8100-intc.o
drivers/irqchip/irq-starfive-jh8100-intc.o: file format elf64-littleriscv
Disassembly of section .data.rel.local:
0000000000000180 <.LASANLOC5>:
...
1d0: 0000 unimp
00000000000001d0: R_RISCV_64 __mod_device_table__kmod_irq_starfive_jh8100_intc__of__starfive_intc_irqchip_match_table
...
This section appears to come from GCC for including additional
information about global variables that may be protected by KASAN.
There appears to be no way to opt out of the generation of these symbols
through either a flag or attribute. Attempting to remove '.LASANLOC*'
with '--strip-symbol' results in the same error as above because these
symbols may refer to (thus have relocation between) each other.
Avoid this build breakage by switching to '--strip-unneeded-symbol' for
removing __mod_device_table__ symbols, as it will only remove the symbol
when there is no relocation pointing to it. While this may result in a
little more bloat in the symbol table in certain configurations, it is
not as bad as outright build failures.
Fixes: 5ab23c7923 ("modpost: Create modalias for builtin modules")
Reported-by: Charles Mirabile <cmirabil@redhat.com>
Closes: https://lore.kernel.org/20251007011637.2512413-1-cmirabil@redhat.com/
Suggested-by: Alexey Gladkov <legion@kernel.org>
Tested-by: Nicolas Schier <nsc@kernel.org>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
