Add support for .get_frame_desc() to report CSI-2 virtual channel
and data type information. This allows CSI-2 receivers to properly
interpret the stream without inferring the data type from the pixel
format.
Signed-off-by: Julien Massot <julien.massot@collabora.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The MT9M114 supports the different slew rates (0 to 7) on the output pads.
At the moment, this is hardcoded to 7 (the fastest rate).
The user might want to change this values due to EMC requirements.
Read the 'slew-rate' from the DT and configure the pad slew rates of
the output pads accordingly in mt9m114_initialize().
Remove the hardcoded slew rate setting from the mt9m114_init table.
Signed-off-by: Mathis Foerst <mathis.foerst@mt.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The current implementation does not apply changes to the crop-
configuration of the sensor immediately if the sensor is in
streaming state. The user has to stop and restart the stream for
the changes to be applied.
This can be undesirable e.g. in a calibration usecase where the user
wants to see the impact of his changes in a live video stream.
Under the condition that the width & height of the cropped image area
does not change, the changed cropping configuration can be applied to
the pixel-array immediately without disturbing the IFP.
Call mt9m114_configure_pa() in mt9m114_pa_set_selection() if the sensor is
in streaming state and the size of the cropping rectangle didn't change,
issue a CONFIG_CHANGE to apply the changes immediately.
Signed-off-by: Mathis Foerst <mathis.foerst@mt.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Added support for three additional test patterns in the
IMX334 driver: Black and Grey Bars, Black Color, and White Color.
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
[Sakari Ailus: Fix hexadecimal value.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The atomisp gc0310 sensor driver has now been fully converted to
a standard v4l2 sensor driver. Move it to drivers/media/i2c/
to reflect this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
MEDIA_CONTROLLER is selected for vim2m already since commit 016baa59bf
("media: Kconfig: Don't expose the Request API option"). Also remove the
related #ifdefs.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The IPU6 ISYS driver supported metadata formats but was missing correct
embedded data type in the receiver configuration. Add it now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The ipu7-isys driver uses v4l2_ctrl_subscribe_event() to handle control
event subscription on a subdev. While this works, it is the wrong API.
Use the subdev-specific v4l2_ctrl_subdev_subscribe_event() helper
instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The ipu6-isys driver uses v4l2_ctrl_subscribe_event() to handle control
event subscription on a subdev. While this works, it is the wrong API.
Use the subdev-specific v4l2_ctrl_subdev_subscribe_event() helper
instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The csi_unsubscribe_event() function simply calls
v4l2_event_unsubscribe(), forwarding its arguments. Replace it with the
v4l2_event_subdev_unsubscribe() helper that performs exactly the same
operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The isp_subdev_unsubscribe_event() function simply calls
v4l2_event_unsubscribe(), forwarding its arguments. Replace it with the
v4l2_event_subdev_unsubscribe() helper that performs exactly the same
operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The ccdc_unsubscribe_event() and omap3isp_stat_unsubscribe_event()
functions simply call v4l2_event_unsubscribe(), forwarding their
arguments. Replace them with the v4l2_event_subdev_unsubscribe() helper
that performs exactly the same operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The v4l2_subdev_stream_config structure holds configuration data for a
stream. It was meant to be used internally only, but already found its
way into the ds90ub913 driver. Now that the driver has been fixed, make
the structure private to v4l2-subdev.c to avoid using it by accident.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The IPU7 ISYS driver can't capture multiple streams on the same video
device. Disallow source multiplexing in the routes of the internal
subdev to reflect that limitation. As a result we can hardcode the
source stream to 0, simplifying the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Use string_choices API instead of manually determining the output using
ternary operator to improve code readability and consistency.
This also fixes cocci warning.
Signed-off-by: Nai-Chen Cheng <bleach1827@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
The platform device name is already set by V4L2 and MC frameworks for
media device bus_info and V4L2 querycap bus_info fields. Don't do it in
the driver.
Acked-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
These defines were used for devices now supported by the imon_raw
driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Move mutex_trylock() in imon_ir_change_protocol() to the beginning,
for memcpy() which modifies ictx->usb_tx_buf should be protected by
ictx->lock.
Also, verify at the beginning of send_packet() that ictx->lock is held
in case send_packet() is by error called from imon_ir_change_protocol()
when mutex_trylock() failed due to concurrent requests.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
syzbot is reporting that imon has three problems which result in
hung tasks due to forever holding device lock [1].
First problem is that when usb_rx_callback_intf0() once got -EPROTO error
after ictx->dev_present_intf0 became true, usb_rx_callback_intf0()
resubmits urb after printk(), and resubmitted urb causes
usb_rx_callback_intf0() to again get -EPROTO error. This results in
printk() flooding (RCU stalls).
Alan Stern commented [2] that
In theory it's okay to resubmit _if_ the driver has a robust
error-recovery scheme (such as giving up after some fixed limit on the
number of errors or after some fixed time has elapsed, perhaps with a
time delay to prevent a flood of errors). Most drivers don't bother to
do this; they simply give up right away. This makes them more
vulnerable to short-term noise interference during USB transfers, but in
reality such interference is quite rare. There's nothing really wrong
with giving up right away.
but imon has a poor error-recovery scheme which just retries forever;
this behavior should be fixed.
Since I'm not sure whether it is safe for imon users to give up upon any
error code, this patch takes care of only union of error codes chosen from
modules in drivers/media/rc/ directory which handle -EPROTO error (i.e.
ir_toy, mceusb and igorplugusb).
Second problem is that when usb_rx_callback_intf0() once got -EPROTO error
before ictx->dev_present_intf0 becomes true, usb_rx_callback_intf0() always
resubmits urb due to commit 8791d63af0 ("[media] imon: don't wedge
hardware after early callbacks"). Move the ictx->dev_present_intf0 test
introduced by commit 6f6b90c923 ("[media] imon: don't parse scancodes
until intf configured") to immediately before imon_incoming_packet(), or
the first problem explained above happens without printk() flooding (i.e.
hung task).
Third problem is that when usb_rx_callback_intf0() is not called for some
reason (e.g. flaky hardware; the reproducer for this problem sometimes
prevents usb_rx_callback_intf0() from being called),
wait_for_completion_interruptible() in send_packet() never returns (i.e.
hung task). As a workaround for such situation, change send_packet() to
wait for completion with timeout of 10 seconds.
Link: https://syzkaller.appspot.com/bug?extid=592e2ab8775dbe0bf09a [1]
Link: https://lkml.kernel.org/r/d6da6709-d799-4be3-a695-850bddd6eb24@rowland.harvard.edu [2]
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
When cdev_device_add() failed, calling put_device() to explicitly
release dev->lirc_dev. Otherwise, it could cause the fault of the
reference count.
Found by code review.
Cc: stable@vger.kernel.org
Fixes: a6ddd4fecb ("media: lirc: remove last remnants of lirc kapi")
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
Remove the extra leading period and provide more elaborate explanation for
why devm_v4l2_sensor_clk_get() is only allowed to be used on camera sensor
devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
devm_clk_get() fails on ACPI-based platforms, where firmware does not
provide a direct reference to the clock producer.
Replace devm_clk_get() with the new v4l2 helper
devm_v4l2_sensor_clk_get() that works on both DT- and ACPI-based
platforms to retrieve a reference to the clock producer from firmware.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
devm_clk_get() fails on ACPI-based platforms, where firmware does not
provide a direct reference to the clock producer.
Replace devm_clk_get() with the new v4l2 helper
devm_v4l2_sensor_clk_get() that works on both DT- and ACPI-based
platforms to retrieve a reference to the clock producer from firmware.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
devm_clk_get() fails on ACPI-based platforms, where firmware does not
provide a direct reference to the clock producer.
Replace devm_clk_get() with the new v4l2 helper
devm_v4l2_sensor_clk_get() that works on both DT- and ACPI-based
platforms to retrieve a reference to the clock producer from firmware.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
devm_clk_get() fails on ACPI-based platforms, where firmware does not
provide a direct reference to the clock producer.
Replace devm_clk_get() with the new v4l2 helper
devm_v4l2_sensor_clk_get() that works on both DT- and ACPI-based
platforms to retrieve a reference to the clock producer from firmware.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
devm_clk_get() fails on ACPI-based platforms, where firmware does not
provide a direct reference to the clock producer.
Replace devm_clk_get() with the new v4l2 helper
devm_v4l2_sensor_clk_get() that works on both DT- and ACPI-based
platforms to retrieve a reference to the clock producer from firmware.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
devm_clk_get() fails on ACPI-based platforms, where firmware does not
provide a direct reference to the clock producer.
Replace devm_clk_get() with the new v4l2 helper
devm_v4l2_sensor_clk_get() that works on both DT- and ACPI-based
platforms to retrieve a reference to the clock producer from firmware.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
devm_clk_get() fails on ACPI-based platforms, where firmware does not
provide a direct reference to the clock producer.
Replace devm_clk_get() with the new v4l2 helper
devm_v4l2_sensor_clk_get() that works on both DT- and ACPI-based
platforms to retrieve a reference to the clock producer from firmware.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
devm_clk_get() fails on ACPI-based platforms, where firmware does not
provide a direct reference to the clock producer.
Replace devm_clk_get() with the new v4l2 helper
devm_v4l2_sensor_clk_get() that works on both DT- and ACPI-based
platforms to retrieve a reference to the clock producer from firmware.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
devm_clk_get() fails on ACPI-based platforms, where firmware does not
provide a direct reference to the clock producer.
Replace devm_clk_get() with the new v4l2 helper
devm_v4l2_sensor_clk_get() that works on both DT- and ACPI-based
platforms to retrieve a reference to the clock producer from firmware.
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mehdi Djait <mehdi.djait@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil+cisco@kernel.org>
