These drivers don't use the driver_data member of struct i2c_device_id,
so don't explicitly initialize this member.
This prepares putting driver_data in an anonymous union which requires
either no initialization or named designators. But it's also a nice
cleanup on its own.
This is a follow up to commit d8a66f3621 ("hwmon: Drop explicit
initialization of struct i2c_device_id::driver_data to 0") which I
created before identifying a few corner cases in my conversion script.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20240508072027.2119857-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Convert driver to register with the hwmon subsystem using
devm_hwmon_device_register_with_info() instead of
devm_hwmon_device_register_with_groups() to simplify the code
and to reduce its size. As side effect, this also fixes a couple
of overflow problems when writing limit and hysteresis registers.
Cc: Lars Petter Mostad <lars.petter.mostad@appear.net>
Tested-by: Lars Petter Mostad <lars.petter.mostad@appear.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since the value for PWMOUT Target Duty Cycle register is a 9 bit
left-justified value that ranges from 0 to 511 and is contained in 2
bytes.
There is an issue that the PWM signal recorded by oscilloscope would
not be on consistently if we set PWM to 100% to the driver.
It is because the LSB of the 9 bit would always be zero if it just
left shift 8 bit for the value that write to PWMOUT Target Duty
Cycle register.
Therefore, revise the scale of the value that was written to pwm input
from 255 to 511 and modify the value to left-justified value.
Signed-off-by: Delphine CC Chiu <Delphine_CC_Chiu@wiwynn.com>
Link: https://lore.kernel.org/r/20240416022211.859483-1-Delphine_CC_Chiu@wiwynn.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Major part of the change for the new method to avoid chipset issues.
The actual update does the following:
1) Lock the memory, but does not perform a SIO entry (previously it
would have performed an SIO entry).
2) Attempt to read the chipID. This should be safe no matter which
chip we have.
3) If step (2) fails, then perform SIO entry and retry chipID read. For
older chips and on failure it acts similarly to prior to this patch.
4) Set the sio_data->type, similar to previously.
5) If we have not performed an SIO entry, and this is not a chip type
with the NOCONF feature, then it will perform an SIO entry at this
point.
6) Proceed with setup as prior to this patch.
7) Any following access to the SIO registers will invoke the SIO entry
and SIO exit steps unless it is a chip with the NOCONF feature set.
This was set up in the previous patches in this patchset.
8) Update to the exit based on if it had performed a SIO entry or not.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20240428060653.2425296-4-frank@crawford.emu.id.au
[groeck: s/intialised/initialized/]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This addition adds in the ability for the system to scan
the EC chip in the Lenovo ThinkStation systems to get the
current fan RPM speeds the Maximum speed value for each
fan also provides the CPU, DIMM other thermal statuses
Signed-off-by: David Ober <dober6023@gmail.com>
Link: https://lore.kernel.org/r/20240328121250.331146-1-dober6023@gmail.com
[groeck: Dropped pointless case statements]
[Colin King: Fixed spelling error accesssible -> accessible]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The Intel Software Development manual defines the temperature digital
readout as the bits [22:16] of the IA32_[PACKAGE]_THERM_STATUS registers.
Bit 23 is specified as reserved.
In recent processors, however, the temperature digital readout uses bits
[23:16]. In those processors, using the bitmask 0x7f would lead to
incorrect readings if the temperature deviates from TjMax by more than
127 degrees Celsius.
Although not guaranteed, bit 23 is likely to be 0 in processors from a few
generations ago. The temperature reading would still be correct in those
processors when using a 0xff bitmask.
Model-specific provisions can be made for older processors in which bit 23
is not 0 should the need arise.
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Link: https://lore.kernel.org/r/20240425171311.19519-4-ricardo.neri-calderon@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() is renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://lore.kernel.org/r/20240409085552.19868-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 4e1008d8aae5 ("dt-bindings: hwmon: pmbus: adp1050: add bindings")
adds the ADP1050 HARDWARE MONITOR DRIVER section, but slips in a typo in
its file entry.
Fortunately, ./scripts/get_maintainer.pl --self-test=patterns complains
about this broken reference.
Fix the typo in ADP1050 HARDWARE MONITOR DRIVER maintainer entry.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Link: https://lore.kernel.org/r/20240402134203.8297-1-lukas.bulwahn@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for ADP1050 Digital Controller for Isolated Power Supplies
with PMBus interface Voltage, Current and Temperature Monitor.
The ADP1050 implements several features to enable a robust
system of parallel and redundant operation for customers who
require high availability. The device can measure voltage,
current and temperature that can be used in different
techniques to identify and safely shut down an erroneous
power supply in parallel operation mode.
Signed-off-by: Radu Sabau <radu.sabau@analog.com>
Link: https://lore.kernel.org/r/20240321142201.10330-2-radu.sabau@analog.com
[groeck: Fixed corrupted link in documentation]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following error can be observed at boot:
[ 3.717920] ACPI Error: No handler for Region [SYSI] (00000000ab9e62c5) [IPMI] (20230628/evregion-130)
[ 3.717928] ACPI Error: Region IPMI (ID=7) has no handler (20230628/exfldio-261)
[ 3.717936] No Local Variables are initialized for Method [_GHL]
[ 3.717938] No Arguments are initialized for method [_GHL]
[ 3.717940] ACPI Error: Aborting method \_SB.PMI0._GHL due to previous error (AE_NOT_EXIST) (20230628/psparse-529)
[ 3.717949] ACPI Error: Aborting method \_SB.PMI0._PMC due to previous error (AE_NOT_EXIST) (20230628/psparse-529)
[ 3.717957] ACPI: \_SB_.PMI0: _PMC evaluation failed: AE_NOT_EXIST
On Dell systems several methods of acpi_power_meter access variables in
IPMI region [0], so wait until IPMI space handler is installed by
acpi_ipmi and also wait until SMI is selected to make the space handler
fully functional.
Since the dependency is inside BIOS's ASL code and it's not
discoverable, so use this fixup is a hack to workaround BIOS issue.
[0] https://www.dell.com/support/manuals/en-us/redhat-enterprise-linux-v8.0/rhel8_rn_pub/advanced-configuration-and-power-interface-acpi-error-messages-displayed-in-dmesg?guid=guid-0d5ae482-1977-42cf-b417-3ed5c3f5ee62
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20240320084317.366853-2-kai.heng.feng@canonical.com
[groeck: Simplified added code]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On Dell servers, many APCI methods of acpi_power_meter module evaluate
variables inside IPMI region, so the region handler needs to be
installed. In addition to that, the handler needs to be fully
functional, and that depends on SMI being selected.
So add a helper to let acpi_power_meter know when the handler is
installed and ready to be used.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: https://lore.kernel.org/r/20240320084317.366853-1-kai.heng.feng@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
