In order to reduce possible memory allocation failures due to memory
fragmentation caused by page_frag_cache allocator, switch to page_pool
allocator for dma and usb mt76 drivers.
Remove per rx-queue page_frag_cache
Co-developed-by: Felix Fietkau <nbd@nbd.name>
Tested-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Free mt76_txwi_cache pointer in mt7915_mmio_wed_init_rx_buf routine in
case of failure.
Fixes: 4f831d18d1 ("wifi: mt76: mt7915: enable WED RX support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The rx filter, in mt7921 series, may be changed in fw operation. There is
a racing problem if rx filter controlled by both driver and firmware at
the same time. To avoid this issue, let mt7921 driver set rx filter by new
command MCU_CE_CMD_SET_RX_FILTER and allow the firmware controlling it
only.
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Neil Chen <yn.chen@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ensure the entry has been fully updated before SDIO bus worker access
it. This patch would fix potential memory risk in both mt7663s and
mt7921s.
Fixes: 764dee47e2 ("mt76: sdio: move common code in mt76_sdio module")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Due to the polling tick is 10ms, the wake up flow in the status waiting
would cause more 10~20ms than the real HW response time. Reduce
tick-interval from 10ms to 1ms to get better network performance, such
as ping latency, in low power mode.
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The default waiting unit is 10ms and the value is too much for
data path related control. Provide a new API mt76_poll_msec_tick()
to support different cases, such as 1ms polling waiting kick.
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The previous commit forgot to remove a leftover check.
Fixes: 43eaa36895 ("wifi: mt76: add PPDU based TxS support for WED device")
Reported-By: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable RED to limit the number of token used by each band. If single band
uses too many tokens, it would hurt the throughput of the other bands.The
software path can solve this problem by AQL so enable RED for HW path only.
Reviewed-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Set sku initial value before mcu starts to prevent mcu from getting an
invalid value.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Comfast CF-952AX is a MT7921 based USB WiFi dongle with custom
VID/PID. Add an entry for it.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The switch default case for frame_contorl is invalid. Return -EINVAL
error for it.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Avoid mcu_restart function pointer whenever it is possible.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt7615_mcu_restart routine directly and avoid mcu_restart function
pointer whenever it is possible.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt7603_mcu_restart routine directly and avoid mcu_restart function
pointer whenever it is possible.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Run mt76_connac_mcu_restart routine directly and avoid mcu_restart
function pointer whenever it is possible.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix device unregister memory leak and alway cleanup all configured
rx queues in mt76_dma_tx_cleanup routine.
Fixes: 52546e2778 ("wifi: mt76: add WED RX support to dma queue alloc")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Free rx_head skb in mt76_dma_rx_cleanup routine in order to avoid
possible memory leak at module unload.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Always purge mcu skb queues in mt7915_mcu_exit routine even if
mt7915_firmware_state fails.
Fixes: e57b790146 ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch does not change any logic, just improve code readability.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
round_jiffies_up() may change the duration reported from chip. We should
take the real timeout for current channel privilege.
Fixes: 034ae28b56 ("wifi: mt76: mt7921: introduce remain_on_channel support")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use the sts variable when setting vht beamform sts cap.
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In newer chipsets, CFEND_RATE setting has been moved to different hw
module.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix per-band chainmask when restoring from the dev chainmask.
Fixes: 98686cd216 ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When the chanctx enabled, IEEE80211_CONF_CHANGE_CHANNEL in .config()
would not be called anymore. mt76 cannot control RF channel for monitor.
Add monitor type set-channel flow in .change_chanctx().
Fixes: 41ac53c899 ("wifi: mt76: mt7921: introduce chanctx support")
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When flash mode is enabled, and the eeprom data in the flash is not for
the current chipset, it'll still be checked valid, and the default
eeprom bin won't be loaded.
(e.g., mt7915 NIC inserted with mt7916 eeprom data in the flash.)
Fix this kind of case by adding chip id into consideration in
mt7915_check_eeprom().
Reported-by: Cheng-Ji Li <cheng-ji.li@mediatek.com>
Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Call mt7915_mcu_set_thermal_protect() through
mt7915_thermal_temp_store() to update firmware trigger/restore temp
directly.
Fixes: 02ee68b95d ("mt76: mt7915: add control knobs for thermal throttling")
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This patch includes 2 changes:
1. Firmware expects to disable thermal protect first before
reconfiguring.
2. Separate setting thermal_protect and setting thermal_tx_duty into
different functions. These two firmware commands do not need to send
together.
Fixes: 34b877d972 ("mt76: mt7915: add thermal cooling device support")
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable thermal management by default shall not be executed during mcu
init. This causes thermal configuration being reset to the firmware
default settings.
Fixes: 0063b86c91 ("mt76: mt7915e: Enable thermal management by default")
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Howard Hsu <howard-yh.hsu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When mt7921_abort_roc is called with dev->mutex held, it can deadlock while
calling cancel_work_sync(&phy->roc_work), because the work function could
be waiting to acquire the mutex.
Fix this by flushing the work before taking the mutex
Reported-by: Mikhail Gavrilov <mikhail.v.gavrilov@gmail.com>
Fixes: 034ae28b56 ("wifi: mt76: mt7921: introduce remain_on_channel support")
Fixes: 41ac53c899 ("wifi: mt76: mt7921: introduce chanctx support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Frank Sae says:
====================
net: add dts for yt8521 and yt8531s, add driver for yt8531
Add dts for yt8521 and yt8531s, add driver for yt8531.
These patches have been verified on our AM335x platform (motherboard)
which has one integrated yt8521 and one RGMII interface.
It can connect to daughter boards like yt8531s or yt8531 board.
v5:
- change the compatible of yaml
- change the maintainers of yaml from "frank sae" to "Frank Sae"
v4:
- change default tx delay from 150ps to 1950ps
- add compatible for yaml
v3:
- change default rx delay from 1900ps to 1950ps
- moved ytphy_rgmii_clk_delay_config_with_lock from yt8521's patch to yt8531's patch
- removed unnecessary checks of phydev->attached_dev->dev_addr
v2:
- split BIT macro as one patch
- split "dts for yt8521/yt8531s ... " patch as two patches
- use standard rx-internal-delay-ps and tx-internal-delay-ps, removed motorcomm,sds-tx-amplitude
- removed ytphy_parse_dt, ytphy_probe_helper and ytphy_config_init_helper
- not store dts arg to yt8521_priv
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for the motorcomm yt8531 gigabit ethernet phy. We have
verified the driver on AM335x platform with yt8531 board. On the
board, yt8531 gigabit ethernet phy works in utp mode, RGMII
interface, supports 1000M/100M/10M speeds, and wol(magic package).
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dts support for Motorcomm yt8531s gigabit ethernet phy.
Change yt8521_probe to support clk config of yt8531s. Becase
yt8521_probe does the things which yt8531s is needed, so
removed yt8531s function.
This patch has been verified on AM335x platform with yt8531s board.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dts support for Motorcomm yt8521 gigabit ethernet phy.
Add ytphy_rgmii_clk_delay_config function to support dst config for
the delay of rgmii clk. This funciont is common for yt8521, yt8531s
and yt8531.
This patch has been verified on AM335x platform.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add BIT macro for Motorcomm yt8521/yt8531 gigabit ethernet phy.
This is a preparatory patch. Add BIT macro for 0xA012 reg, and
supplement for 0xA001 and 0xA003 reg. These will be used to support dts.
Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Buslov says:
====================
net: Allow offloading of UDP NEW connections via act_ct
Currently only bidirectional established connections can be offloaded
via act_ct. Such approach allows to hardcode a lot of assumptions into
act_ct, flow_table and flow_offload intermediate layer codes. In order
to enabled offloading of unidirectional UDP NEW connections start with
incrementally changing the following assumptions:
- Drivers assume that only established connections are offloaded and
don't support updating existing connections. Extract ctinfo from meta
action cookie and refuse offloading of new connections in the drivers.
- Fix flow_table offload fixup algorithm to calculate flow timeout
according to current connection state instead of hardcoded
"established" value.
- Add new flow_table flow flag that designates bidirectional connections
instead of assuming it and hardcoding hardware offload of every flow
in both directions.
- Add new flow_table flow flag that designates connections that are
offloaded to hardware as "established" instead of assuming it. This
allows some optimizations in act_ct and prevents spamming the
flow_table workqueue with redundant tasks.
With all the necessary infrastructure in place modify act_ct to offload
UDP NEW as unidirectional connection. Pass reply direction traffic to CT
and promote connection to bidirectional when UDP connection state
changes to "assured". Rely on refresh mechanism to propagate connection
state change to supporting drivers.
Note that early drop algorithm that is designed to free up some space in
connection tracking table when it becomes full (by randomly deleting up
to 5% of non-established connections) currently ignores connections
marked as "offloaded". Now, with UDP NEW connections becoming
"offloaded" it could allow malicious user to perform DoS attack by
filling the table with non-droppable UDP NEW connections by sending just
one packet in single direction. To prevent such scenario change early
drop algorithm to also consider "offloaded" connections for deletion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both synchronous early drop algorithm and asynchronous gc worker completely
ignore connections with IPS_OFFLOAD_BIT status bit set. With new
functionality that enabled UDP NEW connection offload in action CT
malicious user can flood the conntrack table with offloaded UDP connections
by just sending a single packet per 5tuple because such connections can no
longer be deleted by early drop algorithm.
To mitigate the issue allow both early drop and gc to consider offloaded
UDP connections for deletion.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the offload algorithm of UDP connections to the following:
- Offload NEW connection as unidirectional.
- When connection state changes to ESTABLISHED also update the hardware
flow. However, in order to prevent act_ct from spamming offload add wq for
every packet coming in reply direction in this state verify whether
connection has already been updated to ESTABLISHED in the drivers. If that
it the case, then skip flow_table and let conntrack handle such packets
which will also allow conntrack to potentially promote the connection to
ASSURED.
- When connection state changes to ASSURED set the flow_table flow
NF_FLOW_HW_BIDIRECTIONAL flag which will cause refresh mechanism to offload
the reply direction.
All other protocols have their offload algorithm preserved and are always
offloaded as bidirectional.
Note that this change tries to minimize the load on flow_table add
workqueue. First, it tracks the last ctinfo that was offloaded by using new
flow 'NF_FLOW_HW_ESTABLISHED' flag and doesn't schedule the refresh for
reply direction packets when the offloads have already been updated with
current ctinfo. Second, when 'add' task executes on workqueue it always
update the offload with current flow state (by checking 'bidirectional'
flow flag and obtaining actual ctinfo/cookie through meta action instead of
caching any of these from the moment of scheduling the 'add' work)
preventing the need from scheduling more updates if state changed
concurrently while the 'add' work was pending on workqueue.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tcf_ct_flow_table_fill_actions() function assumes that only
established connections can be offloaded and always sets ctinfo to either
IP_CT_ESTABLISHED or IP_CT_ESTABLISHED_REPLY strictly based on direction
without checking actual connection state. To enable UDP NEW connection
offload set the ctinfo, metadata cookie and NF_FLOW_HW_ESTABLISHED
flow_offload flags bit based on ct->status value.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify flow table offload to cache the last ct info status that was passed
to the driver offload callbacks by extending enum nf_flow_flags with new
"NF_FLOW_HW_ESTABLISHED" flag. Set the flag if ctinfo was 'established'
during last act_ct meta actions fill call. This infrastructure change is
necessary to optimize promoting of UDP connections from 'new' to
'established' in following patches in this series.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify flow table offload to support unidirectional connections by
extending enum nf_flow_flags with new "NF_FLOW_HW_BIDIRECTIONAL" flag. Only
offload reply direction when the flag is set. This infrastructure change is
necessary to support offloading UDP NEW connections in original direction
in following patches in series.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently flow_offload_fixup_ct() function assumes that only replied UDP
connections can be offloaded and hardcodes UDP_CT_REPLIED timeout value. To
enable UDP NEW connection offload in following patches extract the actual
connections state from ct->status and set the timeout according to it.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to offload connections in other states besides "established" the
driver offload callbacks need to have access to connection conntrack info.
Flow offload intermediate representation data structure already contains
that data encoded in 'cookie' field, so just reuse it in the drivers.
Reject offloading IP_CT_NEW connections for now by returning an error in
relevant driver callbacks based on value of ctinfo. Support for offloading
such connections will need to be added to the drivers afterwards.
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable debugfs for vcap for lan966x. This will allow to print all the
entries in the VCAP and also the port information regarding which keys
are configured.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yoshihiro Shimoda says:
====================
net: renesas: rswitch: Modify initialization for SERDES and PHY
- My platform has the 88x2110.
- The MACTYPE setting of strap pin on the platform is SXGMII.
- However, we realized that the SoC cannot communicate the PHY with SXGMII
because of mismatching hardware specification.
- We have a lot of boards which mismatch the MACTYPE setting.
So, I would like to change the MACTYPE as SGMII by software for the platform.
The patch [1/5] sets phydev->host_interfaces by phylink for Marvell PHY
driver (marvell10g) to initialize the MACTYPE.
- The patch [1/5] siplifies the rswitch driver.
- The patch [2/5] converts to phy_device from phylink.
- The patch [3/5] sets phydev->host_interfaces from this driver without
any new functions of phylib.
- The patch [4/5] adds phy_power_on() calling to initialize the Ethernet
SERDES PHY driver (r8a779f0-eth-serdes) for each channel.
- The patch [5/5] adds "max-speed" handling.
Changes from v4:
https://lore.kernel.org/all/20230127142621.1761278-1-yoshihiro.shimoda.uh@renesas.com/
- No modification of phylink API.
- Convert to phylib instead of phylink.
- Add "max-speed" handling.
Changes from v3:
https://lore.kernel.org/all/20230127014812.1656340-1-yoshihiro.shimoda.uh@renesas.com/
- Keep a pointer of "port" and more simplify the code.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
