[Why]
Vendor specific link rate toggle workaround should not be
applied outside of link training scenario, such as when
outputting PHY test pattern.
[How]
Add flag to indicate when link training is occuring.
Make workaround a no-op when flag is not set.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: George Shen <George.Shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Adding a debugfs to show PSR capability of the panel and the driver.
To use:
cat /sys/kernel/debug/dri/0/eDP-X/psr_capability
Expected output:
Sink support: no/yes
Driver support: no/yes
[how]
Adding psr_capability to eDP connectors.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Driver use primary eDP link stream as the condition
to enable fastboot or not.
In dual eDP case, set second screen only,
this would cause slave eDP timing to be used on primary one.
[HOW]
Add a check for unmatched eDP link stream.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain USB4 docks do not seem to be able to handle disabling
DSC once it has been enabled on an MST stream. This can result
in blank displays.
[How]
As a work around, always enable DSC on docks exhibiting this issue. The
flag to indicate the use of DSC for MST streams on a USB4 dock is set
during detection of the dock and only cleared when the USB4 dock is
disconnected.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It seems like after a series of plug/unplugs we end up in a situation
where tiled display doesnt support Audio.
[HOW]
The issue seems to be related to when we check streams changed after an
HPD, we should be checking the audio_struct as well to see if any of its
values changed.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During otg sync trigger, plane states are used to decide whether the otg
is already synchronized or not. There are scenarions when otgs are
disabled without plane state getting disabled and in such case the otg is
excluded from synchronization.
[How]
Introduced pipe_idx_syncd in pipe_ctx that tracks each otgs master pipe.
When a otg is disabled/enabled, pipe_idx_syncd is reset to itself.
On sync trigger, pipe_idx_syncd is checked to decide whether a otg is
already synchronized and the otg is further included or excluded from
synchronization.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: meenakshikumar somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When trying to lightup two 4k60 non-DSC displays behind a branch device
that supports DSC we can't lightup both at once due to bandwidth
limitations - each requires 48 VCPI slots but we only have 63.
[How]
The workaround already exists in the code but is guarded by a CONFIG
that cannot be set by the user and shouldn't need to be.
Check for specific branch device IDs to device whether to enable
the workaround for multiple display scenarios.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change since v1: add brief description
1. Add hdmi frl pcon support to existing asic family.
2. Determine pcon frl capability based on pcon dpcd.
3. pcon frl is taken into consideration into mode validation.
v2: squash in warning fix (Alex)
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
HW_ID_MAX considers HWID of all IPs, far more than what amdgpu uses.
amdgpu tracks only the IPs defined by amd_hw_ip_block_type whose max
is MAX_HWIP.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
>> drivers/gpu/drm/amd/amdgpu/amdgpu_psp.c:503:6: warning: no previous prototype for function 'release_psp_cmd_buf' [-Wmissing-prototypes]
void release_psp_cmd_buf(struct psp_context *psp)
^
drivers/gpu/drm/amd/amdgpu/amdgpu_psp.c:503:1: note: declare 'static' if the function is not intended to be used outside of this translation unit
void release_psp_cmd_buf(struct psp_context *psp)
^
static
1 warning generated.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Kevin Wang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
== Description ==
All the power profile modes use the same strings (or a subset of)
Creating a public array of the strings will allow sharing rather than
duplicating for each chip
First patch only implements change for navi10, followup with other chips
== Changes ==
Create a declaration of the public array in kgd_pp_interface.h
Define the public array in amdgpu_pm.c
Modify the implementaiton of navi10_get_power_profile_mode to use new array
== Test ==
LOGFILE=pp_profile_strings.test.log
AMDGPU_PCI_ADDR=`lspci -nn | grep "VGA\|Display" | cut -d " " -f 1`
AMDGPU_HWMON=`ls -la /sys/class/hwmon | grep $AMDGPU_PCI_ADDR | awk '{print $9}'`
HWMON_DIR=/sys/class/hwmon/${AMDGPU_HWMON}
lspci -nn | grep "VGA\|Display" > $LOGFILE
FILES="pp_power_profile_mode "
for f in $FILES
do
echo === $f === >> $LOGFILE
cat $HWMON_DIR/device/$f >> $LOGFILE
done
cat $LOGFILE
Signed-off-by: Darren Powell <darren.powell@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
IH ring1 is used to process GPU retry fault, overflow is enabled to
drain retry fault because we want receive other interrupts while
handling retry fault to recover range. There is no overflow flag set
when wptr pass rptr. Use timestamp of rptr and wptr to handle overflow
and drain retry fault.
If fault timestamp goes backward, the fault is filtered and should not
be processed. Drain fault is finished if processed_timestamp is equal to
or larger than checkpoint timestamp.
Add amdgpu_ih_functions interface decode_iv_ts for different chips to
get timestamp from IV entry with different iv size and timestamp offset.
amdgpu_ih_decode_iv_ts_helper is used for vega10, vega20, navi10.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2:
still need call ras_disable_all_featrures to handle
ras initilization failure case.
Function amdgpu_device_fini_hw is called before amdgpu_device_fini_sw,
so ras ta will unload before send ras disable command, ras dsiable operation
must before hw fini.
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v1: Ideally power gate/ungate requests shouldn't come when smu block is
uninitialized. Add a WARN message to check the origins if such a thing
ever happens.
v2: Use dev_WARN to log device info (Felix/Guchun).
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Kevin Yang <kevinyang.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The 'doorbell_bitmap' bitmap has just been allocated. So we can use the
non-atomic '__set_bit()' function to save a few cycles as no concurrent
access can happen.
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
'doorbell_bitmap' and 'queue_slot_bitmap' are bitmaps. So use
'bitmap_zalloc()' to simplify code, improve the semantic and avoid some
open-coded arithmetic in allocator arguments.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
for sriov odd# vf will modify vcn0 engine ip revision(due to multimedia bandwidth feature),
which will be mismatched with original vcn0 revision
[HOW]
add new version check for vcn0 disabled revision(3, 0, 192), typically modified under
sriov mode
Signed-off-by: Jane Jian <Jane.Jian@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR currently relies on the kernel's delayed vblank on/off mechanism
as an implicit bufferring mechanism to prevent excessive entry/exit.
Without this delay the user experience is impacted since it can take
a few frames to enter/exit.
[How]
Only allow vblank disable immediate for DC when psr is not supported.
Leave a TODO indicating that this support should be extended in the
future to delay independent of the vblank interrupt.
Fixes: 92020e81dd ("drm/amdgpu/display: set vblank_disable_immediate for DC")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If xnack is on, VM retry fault interrupt send to IH ring1, and ring1
will be full quickly. IH cannot receive other interrupts, this causes
deadlock if migrating buffer using sdma and waiting for sdma done
while handling retry fault.
Remove VMC from IH storm client, enable ring1 write pointer
overflow, then IH will drop retry fault interrupts and be able to receive
other interrupts while driver is handling retry fault.
IH ring1 write pointer doesn't writeback to memory by IH, and ring1
write pointer recorded by self-irq is not updated, so always read
the latest ring1 write pointer from register.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
unmap range always increase atomic svms->drain_pagefaults to simplify
both parent range and child range unmap, page fault handle ignores the
retry fault if svms->drain_pagefaults is set to speed up interrupt
handling. svm_range_drain_retry_fault restart draining if another
range unmap from cpu.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
VMA may be removed before unmap notifier callback, and deferred list
work remove range, return success for this special case as we are
handling stale retry fault.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kfd_process_wq_release drain retry fault to ensure no retry fault comes
after removing kfd process from the hash table, otherwise svm page fault
handler will fail to recover the fault and dump GPU vm fault log.
Refactor deferred list work to get_task_mm and take mmap write lock
to handle all ranges, and avoid mm is gone while inserting mmu notifier.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise when IH process restart, count is zero, the loop will
not exit to wake_up_all after processing AMDGPU_IH_MAX_NUM_IVS
interrupts.
Signed-off-by: Philip Yang <Philip.Yang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Print the error on command submission immediately after submitting to
the SMU. This is rate-limited. It helps to immediately know there was an
error on command submission, rather than leave it up to clients to report
the error, as sometimes they do not.
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Acked-by: Alex Deucher <Alexander.Deucher@amd.com>
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add prints where there are none and none are printed in the callee.
Remove the word "previous" from comment and print to make it shorter and
avoid confusion in various prints.
Cc: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After switching to generic framebuffer framework, we rely on the
->dumb_create routine for frame buffer creation. However, the
different domain flags used are not optimal. Add the contiguous
flag to directly allocate the scanout BO as one linear buffer.
Fixes: 087451f372 ("drm/amdgpu: use generic fb helpers instead of setting up AMD own's.")
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Renoir and newer gfx9 APUs have new TSC register that is
not part of the gfxoff tile, so it can be read without
needing to disable gfx off.
Acked-by: Luben Tuikov <luben.tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
