pinctrl: sh-pfc: Updates for v4.20
- Add SATA and audio pin groups on R-Car M3-N,
- Add EtherAVB pin groups on RZ/G1C,
- Add PWM and display (DU) pin groups on R-Car E3,
- Add support for the new RZ/G2M (r8a774a1) SoC.
The parameter 'community' had been spelled incorrectly.
Fix it here.
As a side effect it satisfies static checkers that issue
the following warnings:
drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Function parameter or member 'community' not described in 'intel_gpio_to_pin'
drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Excess function parameter 'commmunity' description in 'intel_gpio_to_pin'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1292308 ("Missing break in switch")
Addresses-Coverity-ID: 1292309 ("Missing break in switch")
Addresses-Coverity-ID: 1309546 ("Missing break in switch")
Addresses-Coverity-ID: 1357369 ("Missing break in switch")
Addresses-Coverity-ID: 1357389 ("Missing break in switch")
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Depending on MACH_INGENIC prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows to read from debugfs whether the GPIOs requested are set as
input or output.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Merge the code of the gpio-ingenic driver into the pinctrl-ingenic
driver.
The reason behind this, is that the same hardware block handles both pin
config / muxing and GPIO.
ingenic_gpio_probe() have been marked as __init, but for the most part,
the code is the exact same as what it was in the gpio-ingenic driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By using platform_driver_probe() instead of platform_driver_register(),
we can mark the ingenic_pinctrl_probe() function as __init.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using postcore_initcall() makes the driver try to initialize way too
early.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl-ingenic driver now supports the JZ4725B SoC.
Furthermore, the gpio-ingenic driver was dropped and the pinctrl-ingenic
driver is now responsible for providing the GPIO functionality.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin 327 was supposed to be used as a voltage control line for the
SD card regulator, but the SD card port1 does not support UHS-I. It
only supports 3.3V signaling, hence this pin is pointless.
Just a note about the background. At first, hardware engineers tried
to implement the UHS for this port. Then, they needed to shrink the
silicon die size, and gave up the UHS, but forgot to remove the pin
assignment.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin_config_[get|set] functions should return ENOTSUPP if
the requested attribute isn't supported.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are using the generic pin configuration interface so
we can set is_generic.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the pinctrl driver for Meson-G12A SoC which share the similar IP as
the previous Meson-AXG SoC, both use same pinmux ops (register layout).
A new driver is needed here due to the differences in the pins.
Starting from Meson-AXG SoC, the pinctrl controller block use 4
continues register bits to specific the pin mux function, while comparing
to old generation SoC which using variable length register bits for
the pin mux definition. The new design greatly simplify the software model.
For the detail example, one 32bit register can be divided into 8 parts,
each has 4 bits whose value start from 0 - 7, each can describe one pin,
the value 0 is always devoted to GPIO function, while 1 - 7 devoted to
the mux pin function.
Please note, the GPIOE is actually located at AO (always on) bank.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When requesting a gpio as an interrupt, we should make sure to mux the
pin as the GPIO function and configure it to be an input so that various
functions or output signals don't affect the interrupt state of the pin.
So far, we've relied on pinmux configurations in DT to handle this, but
let's explicitly configure this in the code so that DT implementers
don't have to get this part right.
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We rely on devices to use pinmuxing configurations in DT to select the
GPIO function (function 0) if they're going to use the gpio in GPIO
mode. Let's simplify things for driver authors by implementing
gpio_request_enable() for this pinctrl driver to mux out the GPIO
function when the gpio is use from gpiolib.
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Renesas RZ/G2M (r8a774a1) is pin compatible with R-Car M3-W (r8a7796),
however it doesn't have several automotive specific peripherals. Add
an r8a7796 specific pin groups/functions along with common pin
groups/functions for supporting both r8a7796 and r8a774a1 SoCs.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
