While downloading Firmware in the resume flow, it is possible to receive
beacon and send H2C to Firmware. However, if Firmware receives unexpected
H2C during the download process, it will fail. Therefore, we prevent to
send unexpected H2C during download Firmware in WoWLAN mode.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20240620055825.17592-6-pkshih@realtek.com
Currently the number of frames sent to the chip in a single USB Request
Block is limited only by the size of the TX buffer, which is 20 KiB.
Testing reveals that as many as 13 frames get aggregated. This is more
than what any of the chips would like to receive. RTL8822CU, RTL8822BU,
and RTL8821CU want at most 3 frames, and RTL8723DU wants only 1 frame
per URB.
RTL8723DU in particular reliably malfunctions during a speed test if it
receives more than 1 frame per URB. All traffic seems to stop. Pinging
the AP no longer works.
Fix this problem by limiting the number of frames sent to the chip in a
single URB according to what each chip likes.
Also configure RTL8822CU, RTL8822BU, and RTL8821CU to expect 3 frames
per URB.
RTL8703B may or may not be found in USB devices. Declare that it wants
only 1 frame per URB, just in case.
Tested with RTL8723DU and RTL8811CU.
Cc: stable@vger.kernel.org
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/cb46ea35-7e59-4742-9c1f-01ceeaad36fb@gmail.com
Read 32 bits RX info to a local variable to fix race condition between
reading RX length and RX tag.
Another solution is to get RX tag at first statement, but adopted solution
can save some memory read, and also save 15 bytes binary code.
RX tag, a sequence number, is used to ensure that RX data has been DMA to
memory completely, so driver must check sequence number is expected before
reading other data.
This potential problem happens only after enabling 36-bit DMA.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240611021901.26394-2-pkshih@realtek.com
Modern platforms can install more than 4GB memory, so DMA address can
larger than 32 bits. If a platform doesn't enable IOMMU, kernel needs extra
works of swiotlb to help DMA that packets reside on memory over 4GB.
The DMA addressing capability of Realtek WiFi chips is 36 bits, so set
LSB 4 bits of high 32-bit address to register and TX/RX descriptor, which
below figure shows 3-level pointers in TX direction, and RX direction is
similar but 2-level pointers only.
+--------+
| | register to head of TX BD
+---|----+
| +---------+
+-----> | TX BD | (in memory)
+----|----+
| +---------+
+------> | TX WD | (in memory)
+----|----+
| +--------+
+------> | skb |
+--------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240611021901.26394-1-pkshih@realtek.com
Version C of 8922AE hardware will use the same firmware of version B, so
extend rule of firmware recognition to allow less but closest firmware
version. Originally only accept firmware with matched version.
Tested on version A/B/C of 8922AE.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240607140251.8295-1-pkshih@realtek.com
The channel configuration of 8852BT is very similar but a little different
to 8852B, so use chip ID as condition to add extra handles including
external loss compensation, ADC configurations, spur settings and so on.
Don't affect existing 8852BE.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240607070659.80263-3-pkshih@realtek.com
New upcoming chip is RTL8852BE-VT (or RTL8852BTE; 8852BT PCIE interface),
which is a variant of 8852B, and many codes excepting to RF calibration
can be shared, so move common code to an new kernel module named
rtw89_8852b_common.ko.
No logic change.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240607070659.80263-2-pkshih@realtek.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240603091541.8367-7-wsa+renesas@sang-engineering.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_interruptible_timeout() causing patterns like:
timeout = wait_for_completion_interruptible_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240603091541.8367-5-wsa+renesas@sang-engineering.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_for_completion_timeout() causing patterns like:
timeout = wait_for_completion_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240603091541.8367-4-wsa+renesas@sang-engineering.com
There is a confusing pattern in the kernel to use a variable named 'timeout' to
store the result of wait_event_timeout() causing patterns like:
timeout = wait_event_timeout(...)
if (!timeout) return -ETIMEDOUT;
with all kinds of permutations. Use 'time_left' as a variable to make the code
self explaining.
Fix to the proper variable type 'long' while here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240603091541.8367-3-wsa+renesas@sang-engineering.com
This is an effort to get rid of all multiplications from allocation
functions in order to prevent integer overflows [1][2].
As the "cmd_buf" variable is a pointer to "struct at76_command" and
this structure ends in a flexible array:
struct at76_command {
[...]
u8 data[];
} __packed;
the preferred way in the kernel is to use the struct_size() helper to
do the arithmetic instead of the calculation "size + count" in the
kmalloc() function.
Also, declare a new variable (total_size) since the return value of the
struct_size() helper is used several times.
At the same time, prepare for the coming implementation by GCC and Clang
of the __counted_by attribute. Flexible array members annotated with
__counted_by can have their accesses bounds-checked at run-time via
CONFIG_UBSAN_BOUNDS (for array indexing) and CONFIG_FORTIFY_SOURCE (for
strcpy/memcpy-family functions). In this case, it is important to note
that the attribute used is "__counted_by_le" since the counter type is
"__le16".
This way, the code is more readable and safer.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments [1]
Link: https://github.com/KSPP/linux/issues/160 [2]
Signed-off-by: Erick Archer <erick.archer@outlook.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/AS8PR02MB7237578654CEDDFE5F8C17BA8BFE2@AS8PR02MB7237.eurprd02.prod.outlook.com
When EMLSR gets unblocked, the current code checks if the last exit was
due to an EXIT reason (as opposed to a BLOCKING one), and if so, it
does nothing, as in this case a MLO scan was scheduled to run in 30
seconds.
But the code doesn't consider the time that passed from the last exit,
so if immediately after the exit a blocker occurred (e.g. non-BSS
interface), and lasts for more than 30 seconds, then the MLO scan and the
following link selection will decide not to enter EMLSR, and when the
unblocking event finally happens, the reason is still set to the EXIT one,
so it will do nothing, and we will not have the chance to re-enable EMLSR.
Fix this by checking also the time that has passed since the last exit,
only if it is less than 30 seconds, we can count on the scheduled MLO
scan.
Note that clearing the reason itself can't be done since it is needed
for the EMLSR prevention mechanism.
Fixes: 2f33561ea8 ("wifi: iwlwifi: mvm: trigger link selection after exiting EMLSR")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240605140327.58556fc4cfa9.I4c55b3cd9f20b21b37f28258d0fb6842ba413966@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TX queue code was mostly moved out to support an internal
transport that we were never going to publish, but we're no
longer using that. Since we're also going to be dissolving
the virtual transport layer entirely, integrate the TX queue
code into the PCIe layer.
This also has a small kernel of already removing the virtual
transport function layer, since iwl_trans_send_cmd() calls
iwl_trans_pcie_send_hcmd() directly now, even if that still
calls the transport send_cmd method for now, we'll clean it
up later.
Also, not everything is renamed yet.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140327.936b13f45071.Ib219ce01a1e67bcad79d5131626db950252aaa46@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When e.g. wpa_supplicant sets only the MLD "sta" authorized
state, the code actually applies that change, but then returns
an error to userspace anyway because there were no changes to
the link station, and no link ID was given. However, it's not
incorrect to not have a link ID when wanting to change only
the MLD peer ("sta") state, so the code shouldn't require it.
To fix this, separate the "new_link" argument out into a new
three-state enum, because if modify is called on a link STA
only, it should return an error if no link is given or if it
doesn't exist. For modify on the MLD "sta", not having a link
ID is OK, but if there is one it should be validated.
This seems to not have mattered much as wpa_supplicant just
prints a message and continues, and the authorized state was
already set before this error return. However, in the later
code powersave recalculation etc. will be skipped, so that it
may result in never allowing powersave on MLO connections.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605135233.48e2b8af07e3.Ib9793c383fcba118c05100e024f4a11a1c3d0e85@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently NL80211_RATE_INFO_HE_RU_ALLOC_2x996 is not handled in
cfg80211_calculate_bitrate_he(), leading to below warning:
kernel: invalid HE MCS: bw:6, ru:6
kernel: WARNING: CPU: 0 PID: 2312 at net/wireless/util.c:1501 cfg80211_calculate_bitrate_he+0x22b/0x270 [cfg80211]
Fix it by handling 2x996 RU allocation in the same way as 160 MHz bandwidth.
Fixes: c4cbaf7973 ("cfg80211: Add support for HE")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Link: https://msgid.link/20240606020653.33205-3-quic_bqiang@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit 3e2f544dd8 ("net: get stats64 if device if driver is
configured") moved the callback to dev_get_tstats64() to net core, so,
unless the driver is doing some custom stats collection, it does not
need to set .ndo_get_stats64.
Since this driver is now relying in NETDEV_PCPU_STAT_TSTATS, then, it
doesn't need to set the dev_get_tstats64() generic .ndo_get_stats64
function pointer.
In this driver specifically, .ndo_get_stats64 basically points to
dev_fetch_sw_netstats(). Now it will point to dev_get_tstats64(), which
calls netdev_stats_to_stats64() and dev_fetch_sw_netstats().
netdev_stats_to_stats64() seems irrelevant for this driver.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://msgid.link/20240607102045.235071-2-leitao@debian.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With commit 34d21de99c ("net: Move {l,t,d}stats allocation to core and
convert veth & vrf"), stats allocation could be done on net core instead
of this driver.
With this new approach, the driver doesn't have to bother with error
handling (allocation failure checking, making sure free happens in the
right spot, etc). This is core responsibility now.
Move mac80211 driver to leverage the core allocation.
Signed-off-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://msgid.link/20240607102045.235071-1-leitao@debian.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
