Oleksij Rempel says:
====================
net: phy: microchip: LAN88xx reliability fixes
This patch series improves the reliability of the Microchip LAN88xx
PHYs, particularly in edge cases involving fixed link configurations or
forced speed modes.
Patch 1 assigns genphy_soft_reset() to the .soft_reset hook to ensure
that stale link partner advertisement (LPA) bits are properly cleared
during reconfiguration. Without this, outdated autonegotiation bits may
remain visible in some parallel detection cases.
Patch 2 restricts the 100 Mbps workaround (originally intended to handle
cable length switching) to only run when the link transitions to the
PHY_NOLINK state. This prevents repeated toggling that can confuse
autonegotiating link partners such as the Intel i350, leading to
unstable link cycles.
Both patches were tested on a LAN7850 (with integrated LAN88xx PHY)
against an Intel I350 NIC. The full test suite - autonegotiation, fixed
link, and parallel detection - passed successfully.
====================
Link: https://patch.msgid.link/20250709130753.3994461-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Restrict the 100Mbit forced-mode workaround to link-down transitions
only, to prevent repeated link reset cycles in certain configurations.
The workaround was originally introduced to improve signal reliability
when switching cables between long and short distances. It temporarily
forces the PHY into 10 Mbps before returning to 100 Mbps.
However, when used with autonegotiating link partners (e.g., Intel i350),
executing this workaround on every link change can confuse the partner
and cause constant renegotiation loops. This results in repeated link
down/up transitions and the PHY never reaching a stable state.
Limit the workaround to only run during the PHY_NOLINK state. This ensures
it is triggered only once per link drop, avoiding disruptive toggling
while still preserving its intended effect.
Note: I am not able to reproduce the original issue that this workaround
addresses. I can only confirm that 100 Mbit mode works correctly in my
test setup. Based on code inspection, I assume the workaround aims to
reset some internal state machine or signal block by toggling speeds.
However, a PHY reset is already performed earlier in the function via
phy_init_hw(), which may achieve a similar effect. Without a reproducer,
I conservatively keep the workaround but restrict its conditions.
Fixes: e57cf3639c ("net: lan78xx: fix accessing the LAN7800's internal phy specific registers from the MAC driver")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250709130753.3994461-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enable .soft_reset for the LAN88xx PHY driver by assigning
genphy_soft_reset() to ensure that the phylib core performs a proper
soft reset during reconfiguration.
Previously, the driver left .soft_reset unimplemented, so calls to
phy_init_hw() (e.g., from lan88xx_link_change_notify()) did not fully
reset the PHY. As a result, stale contents in the Link Partner Ability
(LPA) register could persist, causing the PHY to incorrectly report
that the link partner advertised autonegotiation even when it did not.
Using genphy_soft_reset() guarantees a clean reset of the PHY and
corrects the false autoneg reporting in these scenarios.
Fixes: ccb989e4d1 ("net: phy: microchip: Reset LAN88xx PHY to ensure clean link state on LAN7800/7850")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250709130753.3994461-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The previous hardcoded definitions of NUM_RX_STATS and
NUM_TX_STATS were not updated when new fields were added
to the ibmvnic_{rx,tx}_queue_stats structures. Specifically,
commit 2ee73c54a6 ("ibmvnic: Add stat for tx direct vs tx
batched") added a fourth TX stat, but NUM_TX_STATS remained 3,
leading to a mismatch.
This patch replaces the static defines with dynamic sizeof-based
calculations to ensure the stat arrays are correctly sized.
This fixes incorrect indexing and prevents incomplete stat
reporting in tools like ethtool.
Fixes: 2ee73c54a6 ("ibmvnic: Add stat for tx direct vs tx batched")
Signed-off-by: Mingming Cao <mmc@linux.ibm.com>
Reviewed-by: Dave Marquardt <davemarq@linux.ibm.com>
Reviewed-by: Haren Myneni <haren@linux.ibm.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250709153332.73892-1-mmc@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When updating an existing route entry in atrtr_create(), the old device
reference was not being released before assigning the new device,
leading to a device refcount leak. Fix this by calling dev_put() to
release the old device reference before holding the new one.
Fixes: c7f905f0f6 ("[ATALK]: Add missing dev_hold() to atrtr_create().")
Signed-off-by: Kito Xu <veritas501@foxmail.com>
Link: https://patch.msgid.link/tencent_E1A26771CDAB389A0396D1681A90A49E5D09@qq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from Paolo Abeni:
"Including fixes from Bluetooth.
Current release - regressions:
- tcp: refine sk_rcvbuf increase for ooo packets
- bluetooth: fix attempting to send HCI_Disconnect to BIS handle
- rxrpc: fix over large frame size warning
- eth: bcmgenet: initialize u64 stats seq counter
Previous releases - regressions:
- tcp: correct signedness in skb remaining space calculation
- sched: abort __tc_modify_qdisc if parent class does not exist
- vsock: fix transport_{g2h,h2g} TOCTOU
- rxrpc: fix bug due to prealloc collision
- tipc: fix use-after-free in tipc_conn_close().
- bluetooth: fix not marking Broadcast Sink BIS as connected
- phy: qca808x: fix WoL issue by utilizing at8031_set_wol()
- eth: am65-cpsw-nuss: fix skb size by accounting for skb_shared_info
Previous releases - always broken:
- netlink: fix wraparounds of sk->sk_rmem_alloc.
- atm: fix infinite recursive call of clip_push().
- eth:
- stmmac: fix interrupt handling for level-triggered mode in DWC_XGMAC2
- rtsn: fix a null pointer dereference in rtsn_probe()"
* tag 'net-6.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
net/sched: sch_qfq: Fix null-deref in agg_dequeue
rxrpc: Fix oops due to non-existence of prealloc backlog struct
rxrpc: Fix bug due to prealloc collision
MAINTAINERS: remove myself as netronome maintainer
selftests/net: packetdrill: add tcp_ooo-before-and-after-accept.pkt
tcp: refine sk_rcvbuf increase for ooo packets
net/sched: Abort __tc_modify_qdisc if parent class does not exist
net: ethernet: ti: am65-cpsw-nuss: Fix skb size by accounting for skb_shared_info
net: thunderx: avoid direct MTU assignment after WRITE_ONCE()
selftests/tc-testing: Create test case for UAF scenario with DRR/NETEM/BLACKHOLE chain
atm: clip: Fix NULL pointer dereference in vcc_sendmsg()
atm: clip: Fix infinite recursive call of clip_push().
atm: clip: Fix memory leak of struct clip_vcc.
atm: clip: Fix potential null-ptr-deref in to_atmarpd().
net: phy: smsc: Fix link failure in forced mode with Auto-MDIX
net: phy: smsc: Force predictable MDI-X state on LAN87xx
net: phy: smsc: Fix Auto-MDIX configuration when disabled by strap
net: stmmac: Fix interrupt handling for level-triggered mode in DWC_XGMAC2
rxrpc: Fix over large frame size warning
net: airoha: Fix an error handling path in airoha_probe()
...
Pull KVM fixes from Paolo Bonzini:
"Many patches, pretty much all of them small, that accumulated while I
was on vacation.
ARM:
- Remove the last leftovers of the ill-fated FPSIMD host state
mapping at EL2 stage-1
- Fix unexpected advertisement to the guest of unimplemented S2 base
granule sizes
- Gracefully fail initialising pKVM if the interrupt controller isn't
GICv3
- Also gracefully fail initialising pKVM if the carveout allocation
fails
- Fix the computing of the minimum MMIO range required for the host
on stage-2 fault
- Fix the generation of the GICv3 Maintenance Interrupt in nested
mode
x86:
- Reject SEV{-ES} intra-host migration if one or more vCPUs are
actively being created, so as not to create a non-SEV{-ES} vCPU in
an SEV{-ES} VM
- Use a pre-allocated, per-vCPU buffer for handling de-sparsification
of vCPU masks in Hyper-V hypercalls; fixes a "stack frame too
large" issue
- Allow out-of-range/invalid Xen event channel ports when configuring
IRQ routing, to avoid dictating a specific ioctl() ordering to
userspace
- Conditionally reschedule when setting memory attributes to avoid
soft lockups when userspace converts huge swaths of memory to/from
private
- Add back MWAIT as a required feature for the MONITOR/MWAIT selftest
- Add a missing field in struct sev_data_snp_launch_start that
resulted in the guest-visible workarounds field being filled at the
wrong offset
- Skip non-canonical address when processing Hyper-V PV TLB flushes
to avoid VM-Fail on INVVPID
- Advertise supported TDX TDVMCALLs to userspace
- Pass SetupEventNotifyInterrupt arguments to userspace
- Fix TSC frequency underflow"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: avoid underflow when scaling TSC frequency
KVM: arm64: Remove kvm_arch_vcpu_run_map_fp()
KVM: arm64: Fix handling of FEAT_GTG for unimplemented granule sizes
KVM: arm64: Don't free hyp pages with pKVM on GICv2
KVM: arm64: Fix error path in init_hyp_mode()
KVM: arm64: Adjust range correctly during host stage-2 faults
KVM: arm64: nv: Fix MI line level calculation in vgic_v3_nested_update_mi()
KVM: x86/hyper-v: Skip non-canonical addresses during PV TLB flush
KVM: SVM: Add missing member in SNP_LAUNCH_START command structure
Documentation: KVM: Fix unexpected unindent warnings
KVM: selftests: Add back the missing check of MONITOR/MWAIT availability
KVM: Allow CPU to reschedule while setting per-page memory attributes
KVM: x86/xen: Allow 'out of range' event channel ports in IRQ routing table.
KVM: x86/hyper-v: Use preallocated per-vCPU buffer for de-sparsified vCPU masks
KVM: SVM: Initialize vmsa_pa in VMCB to INVALID_PAGE if VMSA page is NULL
KVM: SVM: Reject SEV{-ES} intra host migration if vCPU creation is in-flight
KVM: TDX: Report supported optional TDVMCALLs in TDX capabilities
KVM: TDX: Exit to userspace for SetupEventNotifyInterrupt
In reconfig we add the virtual monitor in 2 cases:
1. If we are resuming (it was deleted on suspend)
2. If it was added after an error but before the reconfig
(due to the last non-monitor interface removal).
In the second case, the removal of the non-monitor interface will succeed
but the addition of the virtual monitor will fail, so we add it in the
reconfig.
The problem is that we mislead the driver to think that this is an existing
interface that is getting re-added - while it is actually a completely new
interface from the drivers' point of view.
Some drivers act differently when a interface is re-added. For example, it
might not initialize things because they were already initialized.
Such drivers will - in this case - be left with a partialy initialized vif.
To fix it, add the virtual monitor after reconfig_complete, so the
driver will know that this is a completely new interface.
Fixes: 3c3e21e744 ("mac80211: destroy virtual monitor interface across suspend")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250709233451.648d39b041e8.I2e37b68375278987e303d6c00cc5f3d8334d2f96@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To prevent a potential crash in agg_dequeue (net/sched/sch_qfq.c)
when cl->qdisc->ops->peek(cl->qdisc) returns NULL, we check the return
value before using it, similar to the existing approach in sch_hfsc.c.
To avoid code duplication, the following changes are made:
1. Changed qdisc_warn_nonwc(include/net/pkt_sched.h) into a static
inline function.
2. Moved qdisc_peek_len from net/sched/sch_hfsc.c to
include/net/pkt_sched.h so that sch_qfq can reuse it.
3. Applied qdisc_peek_len in agg_dequeue to avoid crashing.
Signed-off-by: Xiang Mei <xmei5@asu.edu>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://patch.msgid.link/20250705212143.3982664-1-xmei5@asu.edu
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
David Howells says:
====================
rxrpc: Miscellaneous fixes
Here are some miscellaneous fixes for rxrpc:
(1) Fix assertion failure due to preallocation collision.
(2) Fix oops due to prealloc backlog struct not yet having been allocated
if no service calls have yet been preallocated.
====================
Link: https://patch.msgid.link/20250708211506.2699012-1-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When userspace is using AF_RXRPC to provide a server, it has to preallocate
incoming calls and assign to them call IDs that will be used to thread
related recvmsg() and sendmsg() together. The preallocated call IDs will
automatically be attached to calls as they come in until the pool is empty.
To the kernel, the call IDs are just arbitrary numbers, but userspace can
use the call ID to hold a pointer to prepared structs. In any case, the
user isn't permitted to create two calls with the same call ID (call IDs
become available again when the call ends) and EBADSLT should result from
sendmsg() if an attempt is made to preallocate a call with an in-use call
ID.
However, the cleanup in the error handling will trigger both assertions in
rxrpc_cleanup_call() because the call isn't marked complete and isn't
marked as having been released.
Fix this by setting the call state in rxrpc_service_prealloc_one() and then
marking it as being released before calling the cleanup function.
Fixes: 00e907127e ("rxrpc: Preallocate peers, conns and calls for incoming service requests")
Reported-by: Junvyyang, Tencent Zhuque Lab <zhuque@tencent.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: LePremierHomme <kwqcheii@proton.me>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250708211506.2699012-2-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I am moving on from Corigine to different things, for the moment
slightly removed from kernel development. Right now there is nobody I
can in good conscience recommend to take over the maintainer role, but
there are still people available for review, so put the driver state to
'Odd Fixes'.
Additionally add Simon Horman as reviewer - thanks Simon.
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eric Dumazet says:
====================
tcp: better memory control for not-yet-accepted sockets
Address a possible OOM condition caused by a recent change.
Add a new packetdrill test checking the expected behavior.
====================
Link: https://patch.msgid.link/20250707213900.1543248-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When a passive flow has not been accepted yet, it is
not wise to increase sk_rcvbuf when receiving ooo packets.
A very busy server might tune down tcp_rmem[1] to better
control how much memory can be used by sockets waiting
in its listeners accept queues.
Fixes: 63ad7dfedf ("tcp: adjust rcvbuf in presence of reorders")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20250707213900.1543248-2-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While transitioning from netdev_alloc_ip_align() to build_skb(), memory
for the "skb_shared_info" member of an "skb" was not allocated. Fix this
by allocating "PAGE_SIZE" as the skb length, accounting for the packet
length, headroom and tailroom, thereby including the required memory space
for skb_shared_info.
Fixes: 8acacc40f7 ("net: ethernet: ti: am65-cpsw: Add minimal XDP support")
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
Link: https://patch.msgid.link/20250707085201.1898818-1-c-vankar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current logic in nicvf_change_mtu() writes the new MTU to
netdev->mtu using WRITE_ONCE() before verifying if the hardware
update succeeds. However on hardware update failure, it attempts
to revert to the original MTU using a direct assignment
(netdev->mtu = orig_mtu)
which violates the intended of WRITE_ONCE protection introduced in
commit 1eb2cded45 ("net: annotate writes on dev->mtu from
ndo_change_mtu()")
Additionally, WRITE_ONCE(netdev->mtu, new_mtu) is unnecessarily
performed even when the device is not running.
Fix this by:
Only writing netdev->mtu after successfully updating the hardware.
Skipping hardware update when the device is down, and setting MTU
directly. Remove unused variable orig_mtu.
This ensures that all writes to netdev->mtu are consistent with
WRITE_ONCE expectations and avoids unintended state corruption
on failure paths.
Signed-off-by: Alok Tiwari <alok.a.tiwari@oracle.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/20250706194327.1369390-1-alok.a.tiwari@oracle.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ioctl(ATMARP_MKIP) allocates struct clip_vcc and set it to
vcc->user_back.
The code assumes that vcc_destroy_socket() passes NULL skb
to vcc->push() when the socket is close()d, and then clip_push()
frees clip_vcc.
However, ioctl(ATMARPD_CTRL) sets NULL to vcc->push() in
atm_init_atmarp(), resulting in memory leak.
Let's serialise two ioctl() by lock_sock() and check vcc->push()
in atm_init_atmarp() to prevent memleak.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250704062416.1613927-3-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
atmarpd is protected by RTNL since commit f3a0592b37 ("[ATM]: clip
causes unregister hang").
However, it is not enough because to_atmarpd() is called without RTNL,
especially clip_neigh_solicit() / neigh_ops->solicit() is unsleepable.
Also, there is no RTNL dependency around atmarpd.
Let's use a private mutex and RCU to protect access to atmarpd in
to_atmarpd().
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Kuniyuki Iwashima <kuniyu@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250704062416.1613927-2-kuniyu@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In function kvm_guest_time_update(), __scale_tsc() is used to calculate
a TSC *frequency* rather than a TSC value. With low-enough ratios,
a TSC value that is less than 1 would underflow to 0 and to an infinite
while loop in kvm_get_time_scale():
kvm_guest_time_update(struct kvm_vcpu *v)
if (kvm_caps.has_tsc_control)
tgt_tsc_khz = kvm_scale_tsc(tgt_tsc_khz,
v->arch.l1_tsc_scaling_ratio);
__scale_tsc(u64 ratio, u64 tsc)
ratio=122380531, tsc=2299998, N=48
ratio*tsc >> N = 0.999... -> 0
Later in the function:
Call Trace:
<TASK>
kvm_get_time_scale arch/x86/kvm/x86.c:2458 [inline]
kvm_guest_time_update+0x926/0xb00 arch/x86/kvm/x86.c:3268
vcpu_enter_guest.constprop.0+0x1e70/0x3cf0 arch/x86/kvm/x86.c:10678
vcpu_run+0x129/0x8d0 arch/x86/kvm/x86.c:11126
kvm_arch_vcpu_ioctl_run+0x37a/0x13d0 arch/x86/kvm/x86.c:11352
kvm_vcpu_ioctl+0x56b/0xe60 virt/kvm/kvm_main.c:4188
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl+0x12d/0x190 fs/ioctl.c:857
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x59/0x110 arch/x86/entry/common.c:81
entry_SYSCALL_64_after_hwframe+0x78/0xe2
This can really happen only when fuzzing, since the TSC frequency
would have to be nonsensically low.
Fixes: 35181e86df ("KVM: x86: Add a common TSC scaling function")
Reported-by: Yuntao Liu <liuyuntao12@huawei.com>
Suggested-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Jann Horn points out that epoll is decrementing the ep refcount and then
doing a
mutex_unlock(&ep->mtx);
afterwards. That's very wrong, because it can lead to a use-after-free.
That pattern is actually fine for the very last reference, because the
code in question will delay the actual call to "ep_free(ep)" until after
it has unlocked the mutex.
But it's wrong for the much subtler "next to last" case when somebody
*else* may also be dropping their reference and free the ep while we're
still using the mutex.
Note that this is true even if that other user is also using the same ep
mutex: mutexes, unlike spinlocks, can not be used for object ownership,
even if they guarantee mutual exclusion.
A mutex "unlock" operation is not atomic, and as one user is still
accessing the mutex as part of unlocking it, another user can come in
and get the now released mutex and free the data structure while the
first user is still cleaning up.
See our mutex documentation in Documentation/locking/mutex-design.rst,
in particular the section [1] about semantics:
"mutex_unlock() may access the mutex structure even after it has
internally released the lock already - so it's not safe for
another context to acquire the mutex and assume that the
mutex_unlock() context is not using the structure anymore"
So if we drop our ep ref before the mutex unlock, but we weren't the
last one, we may then unlock the mutex, another user comes in, drops
_their_ reference and releases the 'ep' as it now has no users - all
while the mutex_unlock() is still accessing it.
Fix this by simply moving the ep refcount dropping to outside the mutex:
the refcount itself is atomic, and doesn't need mutex protection (that's
the whole _point_ of refcounts: unlike mutexes, they are inherently
about object lifetimes).
Reported-by: Jann Horn <jannh@google.com>
Link: https://docs.kernel.org/locking/mutex-design.html#semantics [1]
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull arm64 fixes from Will Deacon:
- Fix bogus KASAN splat on EFI runtime stack
- Select JUMP_LABEL unconditionally to avoid boot failure with pKVM and
the legacy implementation of static keys
- Avoid touching GCS registers when 'arm64.nogcs' has been passed on
the command-line
- Move a 'cpumask_t' off the stack in smp_send_stop()
- Don't advertise SME-related hwcaps to userspace when ID_AA64PFR1_EL1
indicates that SME is not implemented
- Always check the VMA when handling an Overlay fault
- Avoid corrupting TCR2_EL1 during boot
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/mm: Drop wrong writes into TCR2_EL1
arm64: poe: Handle spurious Overlay faults
arm64: Filter out SME hwcaps when FEAT_SME isn't implemented
arm64: move smp_send_stop() cpu mask off stack
arm64/gcs: Don't try to access GCS registers if arm64.nogcs is enabled
arm64: Unconditionally select CONFIG_JUMP_LABEL
arm64: efi: Fix KASAN false positive for EFI runtime stack
Pull pin control fixes from Linus Walleij:
- Mark som pins as invalid for IRQ use in the Qualcomm driver
- Fix up the use of device properties on the MA35DX Nuvoton, apparently
something went sidewise
- Clear the GPIO debounce settings when going down for suspend in the
AMD driver. Very good for some AMD laptops that now wake up from
suspend again!
- Add the compulsory .can_sleep bool flag in the AW9523 driver, should
have been there from the beginning, now there are users finding the
bug
- Drop some bouncing email address from MAINTAINERS
* tag 'pinctrl-v6.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: aw9523: fix can_sleep flag for GPIO chip
pinctrl: amd: Clear GPIO debounce for suspend
pinctrl: nuvoton: Fix boot on ma35dx platforms
MAINTAINERS: drop bouncing Lakshmi Sowjanya D
pinctrl: qcom: msm: mark certain pins as invalid for interrupts
Oleksij Rempel says:
====================
net: phy: smsc: robustness fixes for LAN87xx/LAN9500
The SMSC 10/100 PHYs (LAN87xx family) found in smsc95xx (lan95xx)
USB-Ethernet adapters show several quirks around the Auto-MDIX feature:
- A hardware strap (AUTOMDIX_EN) may boot the PHY in fixed-MDI mode, and
the current driver cannot always override it.
- When Auto-MDIX is left enabled while autonegotiation is forced off,
the PHY endlessly swaps the TX/RX pairs and never links up.
- The driver sets the enable bit for Auto-MDIX but forgets the override
bit, so userspace requests are silently ignored.
- Rapid configuration changes can wedge the link if PHY IRQs are
enabled.
The four patches below make the MDIX state fully predictable and prevent
link failures in every tested strap / autoneg / MDI-X permutation.
Tested on LAN9512 Eval board.
====================
Link: https://patch.msgid.link/20250703114941.3243890-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Force a fixed MDI-X mode when auto-negotiation is disabled to prevent
link instability.
When forcing the link speed and duplex on a LAN9500 PHY (e.g., with
`ethtool -s eth0 autoneg off ...`) while leaving MDI-X control in auto
mode, the PHY fails to establish a stable link. This occurs because the
PHY's Auto-MDIX algorithm is not designed to operate when
auto-negotiation is disabled. In this state, the PHY continuously
toggles the TX/RX signal pairs, which prevents the link partner from
synchronizing.
This patch resolves the issue by detecting when auto-negotiation is
disabled. If the MDI-X control mode is set to 'auto', the driver now
forces a specific, stable mode (ETH_TP_MDI) to prevent the pair
toggling. This choice of a fixed MDI mode mirrors the behavior the
hardware would exhibit if the AUTOMDIX_EN strap were configured for a
fixed MDI connection.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250703114941.3243890-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Override the hardware strap configuration for MDI-X mode to ensure a
predictable initial state for the driver. The initial mode of the LAN87xx
PHY is determined by the AUTOMDIX_EN strap pin, but the driver has no
documented way to read its latched status.
This unpredictability means the driver cannot know if the PHY has
initialized with Auto-MDIX enabled or disabled, preventing it from
providing a reliable interface to the user.
This patch introduces a `config_init` hook that forces the PHY into a
known state by explicitly enabling Auto-MDIX.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20250703114941.3243890-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct the Auto-MDIX configuration to ensure userspace settings are
respected when the feature is disabled by the AUTOMDIX_EN hardware strap.
The LAN9500 PHY allows its default MDI-X mode to be configured via a
hardware strap. If this strap sets the default to "MDI-X off", the
driver was previously unable to enable Auto-MDIX from userspace.
When handling the ETH_TP_MDI_AUTO case, the driver would set the
SPECIAL_CTRL_STS_AMDIX_ENABLE_ bit but neglected to set the required
SPECIAL_CTRL_STS_OVRRD_AMDIX_ bit. Without the override flag, the PHY
falls back to its hardware strap default, ignoring the software request.
This patch corrects the behavior by also setting the override bit when
enabling Auto-MDIX. This ensures that the userspace configuration takes
precedence over the hardware strap, allowing Auto-MDIX to be enabled
correctly in all scenarios.
Fixes: 05b35e7eb9 ("smsc95xx: add phylib support")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Andre Edich <andre.edich@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250703114941.3243890-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the Synopsys Controller IP XGMAC-10G Ethernet MAC Databook
v3.30a (section 2.7.2), when the INTM bit in the DMA_Mode register is set
to 2, the sbd_perch_tx_intr_o[] and sbd_perch_rx_intr_o[] signals operate
in level-triggered mode. However, in this configuration, the DMA does not
assert the XGMAC_NIS status bit for Rx or Tx interrupt events.
This creates a functional regression where the condition
if (likely(intr_status & XGMAC_NIS)) in dwxgmac2_dma_interrupt() will
never evaluate to true, preventing proper interrupt handling for
level-triggered mode. The hardware specification explicitly states that
"The DMA does not assert the NIS status bit for the Rx or Tx interrupt
events" (Synopsys DWC_XGMAC2 Databook v3.30a, sec. 2.7.2).
The fix ensures correct handling of both edge and level-triggered
interrupts while maintaining backward compatibility with existing
configurations. It has been tested on the hardware device (not publicly
available), and it can properly trigger the RX and TX interrupt handling
in both the INTM=0 and INTM=2 configurations.
Fixes: d6ddfacd95 ("net: stmmac: Add DMA related callbacks for XGMAC2")
Tested-by: EricChan <chenchuangyu@xiaomi.com>
Signed-off-by: EricChan <chenchuangyu@xiaomi.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250703020449.105730-1-chenchuangyu@xiaomi.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull pwm fixes from Uwe Kleine-König:
"Two fixes for v6.16-rc6
The first patch fixes an embarrassing bug in the pwm core. I really
wonder this wasn't found earlier since it's introduction in v6.11-rc1
as it greatly disturbs driving a PWM via sysfs.
The second and last patch fixes a clock balance issue in an error path
of the Mediatek PWM driver"
* tag 'pwm/for-6.16-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ukleinek/linux:
pwm: mediatek: Ensure to disable clocks in error path
pwm: Fix invalid state detection
Pull modules fixes from Daniel Gomez:
"This includes two fixes: one introduced in the current release cycle
and another introduced back in v6.4-rc1. Additionally, as Petr and
Luis mentioned in previous pull requests, add myself (Daniel Gomez) to
the list of modules maintainers.
The first was reported by Intel's kernel test robot, and it addresses
a crash exposed by Sebastian's commit c50d295c37 ("rds: Use
nested-BH locking for rds_page_remainder") by allowing relocations for
the per-CPU section even if it lacks the SHF_ALLOC flag.
Petr and Sebastian went down to the archive history (before Git) and
found the commit that broke it at [1] / [2] ("Don't relocate
non-allocated regions in modules.").
The second fix, reported and fixed by Petr (with additional cleanup),
resolves a memory leak by ensuring proper deallocation if module
loading fails.
We couldn't find a reproducer other than forcing it manually or
leveraging eBPF. So, I tested it by enabling error injection in the
codetag functions through the error path that produces the leak and
made it fail until execmem is unable to allocate more memory"
Link: https://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux-fullhistory.git/commit/?id=b3b91325f3c7 [1]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/?id=1a6100caae [2]
* tag 'modules-6.16-rc6.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/modules/linux:
MAINTAINERS: update Daniel Gomez's role and email address
module: Make sure relocations are applied to the per-CPU section
module: Avoid unnecessary return value initialization in move_module()
module: Fix memory deallocation on error path in move_module()
Under some circumstances, the compiler will emit the following warning for
rxrpc_send_response():
net/rxrpc/output.c: In function 'rxrpc_send_response':
net/rxrpc/output.c:974:1: warning: the frame size of 1160 bytes is larger than 1024 bytes
This occurs because the local variables include a 16-element scatterlist
array and a 16-element bio_vec array. It's probably not actually a problem
as this function is only called by the rxrpc I/O thread function in a
kernel thread and there won't be much on the stack before it.
Fix this by overlaying the bio_vec array over the kvec array in the
rxrpc_local struct. There is one of these per I/O thread and the kvec
array is intended for pointing at bits of a packet to be transmitted,
typically a DATA or an ACK packet. As packets for a local endpoint are
only transmitted by its specific I/O thread, there can be no race, and so
overlaying this bit of memory should be no problem.
Fixes: 5800b1cf3f ("rxrpc: Allow CHALLENGEs to the passed to the app for a RESPONSE")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202506240423.E942yKJP-lkp@intel.com/
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Simon Horman <horms@kernel.org>
cc: linux-afs@lists.infradead.org
Link: https://patch.msgid.link/20250707102435.2381045-2-dhowells@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull bitops UAPI fix from Yury Norov:
"Fix BITS_PER_LONG merge error
Tomas' fix for __BITS_PER_LONG was effectively reverted by a wrong
merge. Fix it and add the related files to MAINTAINERS"
* tag 'bitmap-for-6.16-rc6' of https://github.com/norov/linux:
MAINTAINERS: bitmap: add UAPI headers
uapi: bitops: use UAPI-safe variant of BITS_PER_LONG again (2)
The per-CPU data section is handled differently than the other sections.
The memory allocations requires a special __percpu pointer and then the
section is copied into the view of each CPU. Therefore the SHF_ALLOC
flag is removed to ensure move_module() skips it.
Later, relocations are applied and apply_relocations() skips sections
without SHF_ALLOC because they have not been copied. This also skips the
per-CPU data section.
The missing relocations result in a NULL pointer on x86-64 and very
small values on x86-32. This results in a crash because it is not
skipped like NULL pointer would and can't be dereferenced.
Such an assignment happens during static per-CPU lock initialisation
with lockdep enabled.
Allow relocation processing for the per-CPU section even if SHF_ALLOC is
missing.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202506041623.e45e4f7d-lkp@intel.com
Fixes: 1a6100caae425 ("Don't relocate non-allocated regions in modules.") #v2.6.1-rc3
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Petr Pavlu <petr.pavlu@suse.com>
Link: https://lore.kernel.org/r/20250610163328.URcsSUC1@linutronix.de
Signed-off-by: Daniel Gomez <da.gomez@samsung.com>
Message-ID: <20250610163328.URcsSUC1@linutronix.de>
The function move_module() uses the variable t to track how many memory
types it has allocated and consequently how many should be freed if an
error occurs.
The variable is initially set to 0 and is updated when a call to
module_memory_alloc() fails. However, move_module() can fail for other
reasons as well, in which case t remains set to 0 and no memory is freed.
Fix the problem by initializing t to MOD_MEM_NUM_TYPES. Additionally, make
the deallocation loop more robust by not relying on the mod_mem_type_t enum
having a signed integer as its underlying type.
Fixes: c7ee8aebf6 ("module: add stop-grap sanity check on module memcpy()")
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Daniel Gomez <da.gomez@samsung.com>
Link: https://lore.kernel.org/r/20250618122730.51324-2-petr.pavlu@suse.com
Signed-off-by: Daniel Gomez <da.gomez@samsung.com>
Message-ID: <20250618122730.51324-2-petr.pavlu@suse.com>
Pull crypto library fix from Eric Biggers:
"Fix an uninitialized variable in the s390 optimized SHA-1 and SHA-2.
Note that my librarification changes also fix this by greatly
simplifying how the s390 optimized SHA code is integrated. However, we
need this separate fix for 6.16 and older versions"
* tag 'libcrypto-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiggers/linux:
crypto: s390/sha - Fix uninitialized variable in SHA-1 and SHA-2
Pull sound fixes from Takashi Iwai:
"Here are device-specific small fixes, including HD-audio, USB-audio
and ASoC Intel quirks, as well as ASoC fsl, Cirrus codec and the
legacy AD driver fixes.
All look safe and easy"
* tag 'sound-6.16-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Enable headset Mic on Positivo K116J
ALSA: hda/tas2781: Fix calibration data parser issue
ALSA: ad1816a: Fix potential NULL pointer deref in snd_card_ad1816a_pnp()
ASoC: cs35l56: probe() should fail if the device ID is not recognized
ALSA: hda/realtek: Add quirk for ASUS ExpertBook B9403CVAR
ASoC: Intel: sof_sdw: Add quirks for Lenovo P1 and P16
ALSA: usb-audio: Improve filtering of sample rates on Focusrite devices
ASoC: Intel: soc-acpi: arl: Correct order of cs42l43 matches
MAINTAINERS: update Qualcomm audio codec drivers list
ASoC: fsl_sai: Force a software reset when starting in consumer mode
ASoC: Intel: SND_SOC_INTEL_SOF_BOARD_HELPERS select SND_SOC_ACPI_INTEL_MATCH
ASoC: fsl_asrc: use internal measured ratio for non-ideal ratio mode
ALSA: hda/realtek - Add mute LED support for HP Victus 15-fb2xxx
ALSA: hda: Add missing NVIDIA HDA codec IDs
