Selecting CONFIG_DRM selects CONFIG_VIDEO_NOMODESET, which exports
video_firmware_drivers_only(). This can be used as a first
approximation on whether i915 will be available. It's safe to use as
this is only built when CONFIG_SND_HDA_I915 is selected by CONFIG_I915.
It's not completely fool proof, as you can boot with "nomodeset
i915.modeset=1" to make i915 load regardless, or use
"i915.force_probe=!*" to never load i915, but the common case of
booting with nomodeset to disable all GPU drivers this will work as
intended.
Because of this, we add an extra module parameter,
snd_hda_core.gpu_bind that can be used to signal users intent.
-1 follows nomodeset, 0 disables binding, 1 forces wait/-EPROBE_DEFER
on binding.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231009115437.99976-7-maarten.lankhorst@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: Fixes for v6.6
A fairly large set of fixes here but all driver specific, the biggest
block is Johan's work shaking out issues with device setup and teardown
for the wcd938x driver which is a relatively large but clearly broken
down set of changes.
There is one core helper function added as part of a fix for wsa-macro.
The call to gpiod_set_value_cansleep() in cs42l42_sdw_update_status()
needs the header file gpio/consumer.h to be included.
This was introduced by commit 2d066c6a78 ("ASoC: cs42l42: Avoid stale
SoundWire ATTACH after hard reset")
and caused error:
sound/soc/codecs/cs42l42-sdw.c:374:4: error: implicit declaration of
function ‘gpiod_set_value_cansleep’;
did you mean gpio_set_value_cansleep’?
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2d066c6a78 ("ASoC: cs42l42: Avoid stale SoundWire ATTACH after hard reset")
Link: https://lore.kernel.org/r/20231011134853.20059-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASP1 DOUT line must be defaulted to be high-impedance when
it is not actually transmitting data for an active channel.
In non-SoundWire modes ASP1 will usually be shared by multiple
amps so each amp must only drive the line during the slot for
an enabled TX channel.
In SoundWire mode a custom firmware can use ASP1 as a secondary
chip-to-chip audio link or as GPIO. It should be defaulted to
high-impedance since by default the purpose of this pin is not
known.
Backport note:
On kernel versions before 6.6 the cs35l56->base.regmap argument
to regmap_set_bits() must be changed to cs35l56->regmap.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e496112529 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Link: https://lore.kernel.org/r/20231009153412.30380-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>:
Some codec drivers compare widget names with strcmp, ignoring the component
name prefix. If prefix is used, the comparisons start failing.
Add a helper to fix the issue.
Merge series from Johan Hovold <johan+linaro@kernel.org>:
The wcd938x codec driver happily ignores error handling, something which
has bitten us in the past when we hit a probe deferral:
https://lore.kernel.org/lkml/20230705123018.30903-1-johan+linaro@kernel.org/
Fix up the remaining probe and component bind paths that left resources
allocated and registered after errors to avoid similar future issues.
I own an external usb Webcam, model NexiGo N930AF, which had low mic volume and
inconsistent sound quality. Video works as expected.
(snip)
[ +0.047857] usb 5-1: new high-speed USB device number 2 using xhci_hcd
[ +0.003406] usb 5-1: New USB device found, idVendor=1bcf, idProduct=2283, bcdDevice=12.17
[ +0.000007] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ +0.000004] usb 5-1: Product: NexiGo N930AF FHD Webcam
[ +0.000003] usb 5-1: Manufacturer: SHENZHEN AONI ELECTRONIC CO., LTD
[ +0.000004] usb 5-1: SerialNumber: 20201217011
[ +0.003900] usb 5-1: Found UVC 1.00 device NexiGo N930AF FHD Webcam (1bcf:2283)
[ +0.025726] usb 5-1: 3:1: cannot get usb sound sample rate freq at ep 0x86
[ +0.071482] usb 5-1: 3:2: cannot get usb sound sample rate freq at ep 0x86
[ +0.004679] usb 5-1: 3:3: cannot get usb sound sample rate freq at ep 0x86
[ +0.051607] usb 5-1: Warning! Unlikely big volume range (=4096), cval->res is probably wrong.
[ +0.000005] usb 5-1: [7] FU [Mic Capture Volume] ch = 1, val = 0/4096/1
Set up quirk cval->res to 16 for 256 levels,
Set GET_SAMPLE_RATE quirk flag to stop trying to get the sample rate.
Confirmed that happened anyway later due to the backoff mechanism, after 3 failures
All audio stream on device interfaces share the same values,
apart from wMaxPacketSize and tSamFreq :
(snip)
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 3
bNumEndpoints 1
bInterfaceClass 1 Audio
bInterfaceSubClass 2 Streaming
bInterfaceProtocol 0
iInterface 0
AudioStreaming Interface Descriptor:
bLength 7
bDescriptorType 36
bDescriptorSubtype 1 (AS_GENERAL)
bTerminalLink 8
bDelay 1 frames
wFormatTag 0x0001 PCM
AudioStreaming Interface Descriptor:
bLength 11
bDescriptorType 36
bDescriptorSubtype 2 (FORMAT_TYPE)
bFormatType 1 (FORMAT_TYPE_I)
bNrChannels 1
bSubframeSize 2
bBitResolution 16
bSamFreqType 1 Discrete
tSamFreq[ 0] 44100
Endpoint Descriptor:
bLength 9
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 5
Transfer Type Isochronous
Synch Type Asynchronous
Usage Type Data
wMaxPacketSize 0x005c 1x 92 bytes
bInterval 4
bRefresh 0
bSynchAddress 0
AudioStreaming Endpoint Descriptor:
bLength 7
bDescriptorType 37
bDescriptorSubtype 1 (EP_GENERAL)
bmAttributes 0x01
Sampling Frequency
bLockDelayUnits 0 Undefined
wLockDelay 0x0000
(snip)
Based on the usb data about manufacturer, SPCA2281B3 is the most likely controller IC
Manufacturer does not provide link for datasheet nor detailed specs.
No way to confirm if the firmware supports any other way of getting the sample rate.
Testing patch provides consistent good sound recording quality and volume range.
(snip)
[ +0.045764] usb 5-1: new high-speed USB device number 2 using xhci_hcd
[ +0.106290] usb 5-1: New USB device found, idVendor=1bcf, idProduct=2283, bcdDevice=12.17
[ +0.000006] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ +0.000004] usb 5-1: Product: NexiGo N930AF FHD Webcam
[ +0.000003] usb 5-1: Manufacturer: SHENZHEN AONI ELECTRONIC CO., LTD
[ +0.000004] usb 5-1: SerialNumber: 20201217011
[ +0.043700] usb 5-1: set resolution quirk: cval->res = 16
[ +0.002585] usb 5-1: Found UVC 1.00 device NexiGo N930AF FHD Webcam (1bcf:2283)
Signed-off-by: Christos Skevis <xristos.thes@gmail.com>
Link: https://lore.kernel.org/r/20231006155330.399393-1-xristos.thes@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It has been confirmed that all devices in the Focusrite Clarett USB
series work the same as the devices in the Clarett+ series. Add the
missing PIDs to enable support for the Clarett 2Pre and 4Pre USB.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/ZSFB8EVTG1PK1eq/@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AudioDSP firmware is the one who kicks SDxFIFOS calculation when a
stream is decoupled mode. During firmware bring up procedure, there is
no firmware running and the code-loading stream is always a decoupled
one. So, there is none to trigger the calculation and we end up with
false-positive timeout (-110) messages.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20231006102857.749143-4-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASoC: More fixes for v6.6
Some additional fixes for v6.6, some fairly unremarkable driver specific
ones and a couple of minor core fixes for error handling and improved
logging.
The current version of the loopback driver supports interleaved access
mode only. This patch introduces support for the non-interleaved
access mode.
When in the interleaved mode, the 'copy_play_buf' function copies data
from the playback to the capture buffer using one memcpy call. This call
copies samples for multiple, interleaved channels.
In the non-interleaved mode we have multiple channel buffers, so we have
to perform multiple memcpy calls to copy samples channel after channel.
Add new function called 'copy_play_buf_part_n', which copies a part of
each channel buffer from playback to capture. Modify the 'copy_play_buf'
to use the corresponding memory copy function(just memcpy /
copy_play_buf_part_n) depending on the access mode.
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20230927113555.14877-1-ivan.orlov0322@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While grep'ing for SIS7012, I noticed that there is
only one reference to it in sound/pci/intel8x0m.c,
while most of its code lives in sound/pci/intel8x0.c.
This probably was a simple copy'n'paste mistake, as
the sound/pci/intel8x0m.c driver implements support
for SIS7013 (see DEVICE_SIS), and the two devices
seem to share the same behavior / registers.
Signed-off-by: Thomas Perl <m@thp.io>
Link: https://lore.kernel.org/r/5E4B5CA1-1109-4C82-A581-838ACF19A15D@thp.io
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Focusrite Clarett+ series uses the same protocol as the Scarlett
Gen 2 and Gen 3 series. This patch adds support for the Clarett+ 2Pre
and Clarett+ 4Pre similarly to the existing 8Pre support by adding
appropriate entries to the scarlett2 driver.
The Clarett 2Pre USB and 4Pre USB presumably use the same protocol as
well, so support for them can easily be added if someone can test.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Link: https://lore.kernel.org/r/ZRL7qjC3tYQllT3H@m.b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDAudio stream setup procedure differs between revisions of the
controller device. Currently the differences are handled directly within
AudioDSP platform drivers with if-statements. Implement a more generic
approach and expose a function that a platform driver may use to ensure
the correct procedure is followed each time.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20230926080623.43927-3-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
