Currently, if ath11k is unable to load the calibration data file it will
always exit. However the calibration data may not be present in factory
test mode, so update the logic to allow the driver to execute in FTM mode
even if downloading the calibration data fails.
Tested-on : IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230517135934.16408-5-quic_rajkbhag@quicinc.com
Add support to process factory test mode commands (FTM) for calibration.
By default firmware start with NORMAL mode and to process the FTM commands
firmware needs to be restarted in FTM mode using module parameter ftm_mode.
The pre-request is all the radios should be down before starting the test.
When start command ATH11K_TM_CMD_TESTMODE_START is received, ar->state
is set to Test Mode. If the FTM command or event length is greater
than 256 bytes, it will be broken down into multiple segments and
encoded with TLV header if it is segmented commands, else it is sent
to firmware as it is.
On receiving UTF event from firmware, if it is segmented event, the driver
will wait until it receives all the segments and notify the complete
data to user application. In case the segmented sequence are missed or
lost from the firmware, driver will skip the already received partial data.
In case of unsegmented UTF event from firmware, driver notifies the
data to the user application as it comes. Applications handles
the data further.
Command to boot in ftm mode:
insmod ath11k ftm_mode=1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Govindaraj Saminathan <quic_gsaminat@quicinc.com>
Co-developed-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230517135934.16408-4-quic_rajkbhag@quicinc.com
Sometimes board-2.bin does not have the regdb data which matched the
parameters such as vendor, device, subsystem-vendor, subsystem-device
and etc. Add default regdb data with 'bus=%s' into board-2.bin for
WCN6855, then ath11k use 'bus=pci' to search regdb data in board-2.bin
for WCN6855.
kernel: [ 122.515808] ath11k_pci 0000:03:00.0: boot using board name 'bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262'
kernel: [ 122.517240] ath11k_pci 0000:03:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 6179564
kernel: [ 122.517280] ath11k_pci 0000:03:00.0: failed to fetch regdb data for bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=3374,qmi-chip-id=2,qmi-board-id=262 from ath11k/WCN6855/hw2.0/board-2.bin
kernel: [ 122.517464] ath11k_pci 0000:03:00.0: boot using board name 'bus=pci'
kernel: [ 122.518901] ath11k_pci 0000:03:00.0: boot firmware request ath11k/WCN6855/hw2.0/board-2.bin size 6179564
kernel: [ 122.518915] ath11k_pci 0000:03:00.0: board name
kernel: [ 122.518917] ath11k_pci 0000:03:00.0: 00000000: 62 75 73 3d 70 63 69 bus=pci
kernel: [ 122.518918] ath11k_pci 0000:03:00.0: boot found match regdb data for name 'bus=pci'
kernel: [ 122.518920] ath11k_pci 0000:03:00.0: boot found regdb data for 'bus=pci'
kernel: [ 122.518921] ath11k_pci 0000:03:00.0: fetched regdb
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230517133959.8224-1-quic_wgong@quicinc.com
In order to support different power levels of 6 GHz AP and client, new WMI
event for regulatory (WMI_REG_CHAN_LIST_CC_EXT_EVENTID) has been added in
firmware to provide new parameters required for 6 GHz regulatory rules.
Firmware advertises its capability of handling new event in WMI service ready
event. Based on that, host needs to set host_service_flags in WMI init command
to indicate that host supports processing of this WMI event. Based on
advertised host capability, firmware sends event WMI_REG_CHAN_LIST_CC_EXT_EVENTID.
This new event contains 2G/5G/6G reg rules with additional power value fields
for 6GHz and regd is built accordingly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230502142018.20301-1-quic_rgnanase@quicinc.com
ath.git patches for v6.5. Major changes:
ath11k
* Multiple Basic Service Set Identifier (MBSSID) and Enhanced MBSSID
Advertisement (EMA) support in AP mode
Due to the firmware behavior with HT fixed rate setting,
HT fixed rate MCS with NSS > 1 are treated as NSS = 1
HT rates in the firmware and enables the HT fixed rate of
NSS = 1.
This leads to HT fixed rate is always configured for NSS = 1
even though the user sets NSS = 2 or > 1 HT fixed MCS in the
set bitrate command.
Currently HT fixed MCS is sent via WMI peer assoc command.
Fix this issue, by sending the HT fixed rate MCS in WMI peer
fixed param instead of sending in peer assoc command.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230504092033.3542456-3-quic_mkenna@quicinc.com
Relocate the function ath11k_mac_bitrate_mask_num_ht_rates() definition
to call this function from other functions which helps to avoid the
compilation error (function not defined).
ht_mcs[] is 1 byte array and it is enough to use hweight8() instead
of hweight16(). Hence, fixed the same.
Tested on: Compile tested only.
Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230504092033.3542456-2-quic_mkenna@quicinc.com
When vdev start/stop happens, response from firmware is received with delay
and hence there is a timeout before VDEV can be up/down.
Also, with maximum peers connected and when vdev stop occurs, firmware
will take time to clean up all the peers and vap queues.
In such cases as well, vdev start/stop response is sent by firmware with delay.
Increase the vdev setup timeout as recommended by firmware team.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aishwarya R <quic_aisr@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230428091041.20033-1-quic_rgnanase@quicinc.com
TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.
When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.
To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-4-pkshih@realtek.com
DPK is short for digital pre-distortion calibration. It can adjusts digital
waveform according to PA linear characteristics dynamically to enhance
TX EVM.
Do this calibration when we are going to run on AP channel. To prevent
power offset out of boundary, it monitors thermal and set proper boundary
to register.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-3-pkshih@realtek.com
Set MAC/BB/RF registers according to channel we are going to set. In
additional, certain channels or bands need more deals, such as enable CCK
in 2 GHz band, spur elimination at certain frequencies.
The set channel helper is used to save/restore states before/after setting
channel, and does reset BB to prevent hardware getting stuck in abnormal
state during switching channel and receiving data.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230512061220.16544-6-pkshih@realtek.com
This is a newer chip, similar to the RTL8710BU in that it uses the same
PHY status structs.
Features: 2.4 GHz, b/g/n mode, 2T2R, 300 Mbps.
It can allegedly have Bluetooth, but that's not implemented here.
This chip can have many RFE (RF front end) types, of which types 1
and 5 are the only ones tested. Many of the other types need different
initialisation tables. They can be added if someone wants them.
The vendor driver v5.8.6.2_35538.20191028_COEX20190910-0d02 from
https://github.com/BrightX/rtl8192fu was used as reference, with
additional device IDs taken from
https://github.com/kelebek333/rtl8192fu-dkms.
The vendor driver also claims to support devices with ID 0bda:a725,
but that is found in some bluetooth-only devices, so it's not supported
here.
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7dcf9fb9-1c97-ac28-5286-2236e287a18c@gmail.com
As low_thresh has no work in fragment reassembles,del it.
And Mark it deprecated in sysctl Document.
Signed-off-by: Angus Chen <angus.chen@jaguarmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle valo says:
====================
wireless-next patches for v6.5
The first pull request for v6.5 and only driver changes this time.
rtl8xxxu has been making lots of progress lately and now has AP mode
support.
Major changes:
rtl8xxxu
* AP mode support, initially only for rtl8188f
rtw89
* provide RSSI, EVN and SNR statistics via debugfs
* support U-NII-4 channels on 5 GHz band
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When writing error messages to extack for pseudo collisions, we can't
use encap->type as encap has already been freed. Fortunately the
same value is stored in local variable em_type, so use that instead.
Fixes: 3c9561c0a5 ("sfc: support TC decap rules matching on enc_ip_tos")
Reported-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both phylink_create() and phylink_fwnode_phy_connect() do not modify
the fwnode argument that they are passed, so lets constify these.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
On mpfs, with SRAM configured for 4 queues, setting max_tx_len
to GEM_TX_MAX_LEN=0x3f0 results multiple AMBA errors.
Setting max_tx_len to (4KiB - 56) removes those errors.
The details are described in erratum 1686 by Cadence
The max jumbo frame size is also reduced for mpfs to (4KiB - 56).
Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since introduced in commit c319b4d76b ("net: ipv4: add IPPROTO_ICMP
socket kind"), ping socket does not use SLAB_TYPESAFE_BY_RCU nor check
nulls marker in loops.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yunsheng Lin says:
====================
net: introduce skb_frag_fill_page_desc()
Most users use __skb_frag_set_page()/skb_frag_off_set()/
skb_frag_size_set() to fill the page desc for a skb frag.
It does not make much sense to calling __skb_frag_set_page()
without calling skb_frag_off_set(), as the offset may depend
on whether the page is head page or tail page, so add
skb_frag_fill_page_desc() to fill the page desc for a skb
frag.
In the future, we can make sure the page in the frag is
head page of compound page or a base page, if not, we
may warn about that and convert the tail page to head
page and update the offset accordingly, if we see a warning
about that, we also fix the caller to fill the head page
in the frag. when the fixing is done, we may remove the
warning and converting.
In this way, we can remove the compound_head() or use
page_ref_*() like the below case:
https://elixir.bootlin.com/linux/latest/source/net/core/page_pool.c#L881https://elixir.bootlin.com/linux/latest/source/include/linux/skbuff.h#L3383
It may also convert net stack to use the folio easier.
V1: repost with all the ack/review tags included.
RFC: remove a local variable as pointed out by Simon.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users use __skb_frag_set_page()/skb_frag_off_set()/
skb_frag_size_set() to fill the page desc for a skb frag.
Introduce skb_frag_fill_page_desc() to do that.
net/bpf/test_run.c does not call skb_frag_off_set() to
set the offset, "copy_from_user(page_address(page), ...)"
and 'shinfo' being part of the 'data' kzalloced in
bpf_test_init() suggest that it is assuming offset to be
initialized as zero, so call skb_frag_fill_page_desc()
with offset being zero for this case.
Also, skb_frag_set_page() is not used anymore, so remove
it.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add test to make sure that the localbypass option is on by default.
Add test to change vxlan localbypass to nolocalbypass and check
that packets are delivered to userspace.
Signed-off-by: Vladimir Nikishkin <vladimir@nikishkin.pw>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a packet needs to be encapsulated towards a local destination IP, the
packet will undergo a "local bypass" and be injected into the Rx path as
if it was received by the target VXLAN device without undergoing
encapsulation. If such a device does not exist, the packet will be
dropped.
There are scenarios where we do not want to perform such a bypass, but
instead want the packet to be encapsulated and locally received by a
user space program for post-processing.
To that end, add a new VXLAN device attribute that controls whether a
"local bypass" is performed or not. Default to performing a bypass to
maintain existing behavior.
Signed-off-by: Vladimir Nikishkin <vladimir@nikishkin.pw>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
Support for Wake-on-LAN for Broadcom PHYs
This patch series adds support for Wake-on-LAN to the Broadcom PHY
driver. Specifically the BCM54210E/B50212E are capable of supporting
Wake-on-LAN using an external pin typically wired up to a system's GPIO.
These PHY operate a programmable Ethernet MAC destination address
comparator which will fire up an interrupt whenever a match is received.
Because of that, it was necessary to introduce patch #1 which allows the
PHY driver's ->suspend() routine to be called unconditionally. This is
necessary in our case because we need a hook point into the device
suspend/resume flow to enable the wake-up interrupt as late as possible.
Patch #2 adds support for the Broadcom PHY library and driver for
Wake-on-LAN proper with the WAKE_UCAST, WAKE_MCAST, WAKE_BCAST,
WAKE_MAGIC and WAKE_MAGICSECURE. Note that WAKE_FILTER is supportable,
however this will require further discussions and be submitted as a RFC
series later on.
Patch #3 updates the GENET driver to defer to the PHY for Wake-on-LAN if
the PHY supports it, thus allowing the MAC to be powered down to
conserve power.
Changes in v3:
- collected Reviewed-by tags
- explicitly use return 0 in bcm54xx_phy_probe() (Paolo)
Changes in v2:
- introduce PHY_ALWAYS_CALL_SUSPEND and only have the Broadcom PHY
driver set this flag to minimize changes to the suspend flow to only
drivers that need it
- corrected possibly uninitialized variable in bcm54xx_set_wakeup_irq
(Simon)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If available, interrogate the PHY to find out whether we can use it for
Wake-on-LAN. This can be a more power efficient way of implementing
that feature, especially when the MAC is powered off in low power
states.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for WAKE_UCAST, WAKE_MCAST, WAKE_BCAST, WAKE_MAGIC and
WAKE_MAGICSECURE. This is only supported with the BCM54210E and
compatible Ethernet PHYs. Using the in-band interrupt or an out of band
GPIO interrupts are supported.
Broadcom PHYs will generate a Wake-on-LAN level low interrupt on LED4 as
soon as one of the supported patterns is being matched. That includes
generating such an interrupt even if the PHY is operated during normal
modes. If WAKE_UCAST is selected, this could lead to the LED4 interrupt
firing up for every packet being received which is absolutely
undesirable from a performance point of view.
Because the Wake-on-LAN configuration can be set long before the system
is actually put to sleep, we cannot have an interrupt service routine to
clear on read the interrupt status register and ensure that new packet
matches will be detected.
It is desirable to enable the Wake-on-LAN interrupt as late as possible
during the system suspend process such that we limit the number of
interrupts to be handled by the system, but also conversely feed into
the Linux's system suspend way of dealing with interrupts in and around
the points of no return.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few PHY drivers are currently attempting to not suspend the PHY when
Wake-on-LAN is enabled, however that code is not currently executing at
all due to an early check in phy_suspend().
This prevents PHY drivers from making an appropriate decisions and put
the hardware into a low power state if desired.
In order to allow the PHY drivers to opt into getting their ->suspend
routine to be called, add a PHY_ALWAYS_CALL_SUSPEND bit which can be
set. A boolean that tracks whether the PHY or the attached MAC has
Wake-on-LAN enabled is also provided for convenience.
If phydev::wol_enabled then the PHY shall not prevent its own
Wake-on-LAN detection logic from working and shall not prevent the
Ethernet MAC from receiving packets for matching.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Edward Cree says:
====================
sfc: more flexible encap matches on TC decap rules
This series extends the TC offload support on EF100 to support optionally
matching on the IP ToS and UDP source port of the outer header in rules
performing tunnel decapsulation. Both of these fields allow masked
matches if the underlying hardware supports it (current EF100 hardware
supports masking on ToS, but only exact-match on source port).
Given that the source port is typically populated from a hash of inner
header entropy, it's not clear whether filtering on it is useful, but
since we can support it we may as well expose the capability.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow efx_tc_encap_match entries to include a udp_sport and a
udp_sport_mask. As with enc_ip_tos, use pseudos to enforce that all
encap matches within a given <src_ip,dst_ip,udp_dport> tuple have
the same udp_sport_mask.
Note that since we use a single layer of pseudos for both fields, two
matches that differ in (say) udp_sport value aren't permitted to have
different ip_tos_mask, even though this would technically be safe.
Current userland TC does not support setting enc_src_port; this patch
was tested with an iproute2 patched to support it.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow efx_tc_encap_match entries to include an ip_tos and ip_tos_mask.
To avoid partially-overlapping Outer Rules (which can lead to undefined
behaviour in the hardware), store extra "pseudo" entries in our
encap_match hashtable, which are used to enforce that all Outer Rule
entries within a given <src_ip,dst_ip,udp_dport> tuple (or IPv6
equivalent) have the same ip_tos_mask.
The "direct" encap_match entry takes a reference on the "pseudo",
allowing it to be destroyed when all "direct" entries using it are
removed.
efx_tc_em_pseudo_type is an enum rather than just a bool because in
future an additional pseudo-type will be added to support Conntrack
offload.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tc.c will block them before they get here, but following
patch will change that.
Use the extack message from efx_mae_check_encap_match_caps() instead
of writing a new one, since there's now more being fed in than just
an IP version.
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When force-freeing leftover entries from our match_action_ht, call
efx_tc_delete_rule(), which releases all the rule's resources, rather
than open-coding it. The open-coded version was missing a call to
release the rule's encap match (if any).
It probably doesn't matter as everything's being torn down anyway, but
it's cleaner this way and prevents further error messages potentially
being logged by efx_tc_encap_match_free() later on.
Move efx_tc_flow_free() further down the file to avoid introducing a
forward declaration of efx_tc_delete_rule().
Fixes: 17654d84b4 ("sfc: add offloading of 'foreign' TC (decap) rules")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ->bpf_bypass_getsockopt proto callback and filter out
SCTP_SOCKOPT_PEELOFF, SCTP_SOCKOPT_PEELOFF_FLAGS and SCTP_SOCKOPT_CONNECTX3
socket options from running eBPF hook on them.
SCTP_SOCKOPT_PEELOFF and SCTP_SOCKOPT_PEELOFF_FLAGS options do fd_install(),
and if BPF_CGROUP_RUN_PROG_GETSOCKOPT hook returns an error after success of
the original handler sctp_getsockopt(...), userspace will receive an error
from getsockopt syscall and will be not aware that fd was successfully
installed into a fdtable.
As pointed by Marcelo Ricardo Leitner it seems reasonable to skip
bpf getsockopt hook for SCTP_SOCKOPT_CONNECTX3 sockopt too.
Because internaly, it triggers connect() and if error is masked
then userspace will be confused.
This patch was born as a result of discussion around a new SCM_PIDFD interface:
https://lore.kernel.org/all/20230413133355.350571-3-aleksandr.mikhalitsyn@canonical.com/
Fixes: 0d01da6afc ("bpf: implement getsockopt and setsockopt hooks")
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Christian Brauner <brauner@kernel.org>
Cc: Stanislav Fomichev <sdf@google.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Cc: Xin Long <lucien.xin@gmail.com>
Cc: linux-sctp@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: netdev@vger.kernel.org
Suggested-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Alexander Mikhalitsyn <aleksandr.mikhalitsyn@canonical.com>
Acked-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Guillaume Nault says:
====================
selftests: fcnal: Test SO_DONTROUTE socket option.
The objective is to cover kernel paths that use the RTO_ONLINK flag
in .flowi4_tos. This way we'll be able to safely remove this flag in
the future by properly setting .flowi4_scope instead. With these
selftests in place, we can make sure this won't introduce regressions.
For more context, the final objective is to convert .flowi4_tos to
dscp_t, to ensure that ECN bits don't influence route and fib-rule
lookups (see commit a410a0cf98 ("ipv6: Define dscp_t and stop taking
ECN bits into account in fib6-rules")).
These selftests only cover IPv4, as SO_DONTROUTE has no effect on IPv6
sockets.
v2:
- Use two different nettest options for setting SO_DONTROUTE either
on the server or on the client socket.
- Use the above feature to run a single 'nettest -B' instance per
test (instead of having two nettest processes for server and
client).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ping -r to test the kernel behaviour with raw and ping sockets
having the SO_DONTROUTE option.
Since ipv4_ping_novrf() is called with different values of
net.ipv4.ping_group_range, then it tests both raw and ping sockets
(ping uses ping sockets if its user ID belongs to ping_group_range
and raw sockets otherwise).
With both socket types, sending packets to a neighbour (on link) host,
should work. When the host is behind a router, sending should fail.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
