Enable runtime debug control of whether the PEC byte is exchanged with
the PMBus device.
Some manufacturers have asked for the PEC to be disabled as part of
debugging driver communication issues with devices.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20200910021106.2958382-1-andrew@aj.id.au
[groeck: Replace %1llu with %llu]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Caching register values can be very expensive for PMBus chips. Some
modern chips may have 10 or more pages, with several sensors supported
per page. For example, MAX16601 creates more than 90 sysfs attributes.
Register caching for such chips is time consuming, especially if only a
few attributes are read on a regular basis. For MAX16601, it was observed
that it can take up to two seconds to read all attributes on a slow I2C
bus. In this situation, register caching results in the opposite of its
intention: It increases the number of I2C operations, in some cases
substantially, and it results in large latency when trying to access
individual sensor data.
Drop all register caching to solve the problem. Since it is no longer
necessary, drop status register mapping as part of the change, and specify
status registers directly.
Cc: Alex Qiu <xqiu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alex Qiu <xqiu@google.com>
Tested-by: Alex Qiu <xqiu@google.com>
Link: https://lore.kernel.org/r/20200904163314.259087-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The debugfs code was intended to aid figuring out functionality
of undocumented registers. Turns out that wasn't very helpful,
since register locations change too much between AMD chip revisions,
and the data isn't really valuable for chips where it isn't already
supported. On top of that, its existence has been used as argument
for providing pseudo-API debugfs functions in other drivers.
So let's just take it out.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the nvmem kernel api to expose the black box
chip functionality to userspace.
Using this feature, the device is capable of recording
to nonvolatile flash memory the vital data about the
system status that caused the system to perform a
black box write.
A blackbox is 64 bytes of data containing all the
status registers, last two states of the sequencer,
timestamp and counters. The mapping of this data is
described in the adm1266 datasheet.
On power-up the driver sets the unix time to
the adm1266 using the SET_RTC command. This value
is incremented by an internal clock and it is used
as timestamp for the black box feature.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20200812142055.9213-6-alexandru.tachici@analog.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160035.590142-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160159.591293-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
As part of the ongoing i2c transition to the simple probe
("probe_new"), this patch uses i2c_match_id to retrieve the
driver_data for the probed device. The id parameter is thus no longer
necessary and the simple probe can be used instead.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160231.592571-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many hwmon drivers don't use the id information provided by the old
i2c probe function, and the remainder can easily be adapted to the new
form ("probe_new") by calling i2c_match_id explicitly.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified to call i2c_match_id() with the same level of
error-handling (if any) as before.
This patch wraps up the transition for hwmon, with four stragglers not
included in the previous large patch.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200821160354.594715-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many hwmon drivers don't use the id information provided by the old
i2c probe function, and the remainder can easily be adapted to the new
form ("probe_new") by calling i2c_match_id explicitly.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
A few drivers aren't included in this patch because they have a
different set of maintainers. They will be covered by other patches.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20200813160222.1503401-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus_do_probe doesn't use the id information provided in its second
argument, so this can be removed, which then allows using the
single-parameter i2c probe function ("probe_new") for probes.
This avoids scanning the identifier tables during probes.
Drivers which didn't use the id are converted as-is; drivers which did
are modified as follows:
* if the information in i2c_client is sufficient, that's used instead
(client->name);
* configured v. probed comparisons are performed by comparing the
configured name to the detected name, instead of the ids; this
involves strcmp but is still cheaper than comparing all the device
names when scanning the tables;
* anything else is handled by calling i2c_match_id() with the same
level of error-handling (if any) as before.
Additionally, the mismatch message in the ltc2978 driver is adjusted
so that it no longer assumes that the driver_data is an index into
ltc2978_id.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200808210004.30880-1-steve@sk2.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On some drives, reading the drive temperature resets the drive's
spin-down timer. If the drive temperature is read too often, affected
drives will never spin down. Add this information as usage note to
the driver documentation.
Reported-by: Peter Sulyok <peter@sulyok.net>
Cc: Peter Sulyok <peter@sulyok.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding implementation for new attributes (rated_min/rated_max) for
currentX, inX, powerX, tempX and humidityX.
Tested with OpenBMC stack and simple hwmon driver using
rated_min/rated_max for the following types of sensors: hwmon_temp,
hwmon_in, hwmon_curr, hwmon_power, hwmon_humidity.
For each sensor rated attributes were available and returned
expected values.
Signed-off-by: Zbigniew Lukwinski <zbigniew.lukwinski@linux.intel.com>
Link: https://lore.kernel.org/r/1596224237-32280-3-git-send-email-zbigniew.lukwinski@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Smatch has a new check for resource leaks which found a bug in probe:
drivers/hwmon/w83627ehf.c:2417 w83627ehf_probe()
warn: 'res->start' not released on lines: 2412.
We need to clean up if devm_hwmon_device_register_with_info() fails.
Fixes: 266cd58359 ("hwmon: (w83627ehf) convert to with_info interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dr. David Alan Gilbert <linux@treblig.org>
Link: https://lore.kernel.org/r/20200921125212.GA1128194@mwanda
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Starting with MAX34451, the chips of this series support STATUS_IOUT and
STATUS_TEMPERATURE commands, and no longer report over-current and
over-temperature status with STATUS_MFR_SPECIFIC.
Fixes: 7a001dbab4 ("hwmon: (pmbus/max34440) Add support for MAX34451.")
Fixes: 50115ac9b6 ("hwmon: (pmbus/max34440) Add support for MAX34460 and MAX34461")
Reported-by: Steve Foreman <foremans@google.com>
Cc: Steve Foreman <foremans@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the temperature is read before the internal calibration is
completed, the driver returns -EIO. Instead it should return -EAGAIN
to encourage repeating the operation.
Note (groeck): Returning -EAGAIN to userspace may result in hard loops;
some userspace code interprets -EAGAIN as request to retry immediately.
I would prefer -ENODATA, but it turns out that the thermal subsystem only
handles -EAGAIN silently, so we'll have to stick with that.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200903134704.8949-1-lars.povlsen@microchip.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull syscall tracing fix from Borislav Petkov:
"Fix the seccomp syscall rewriting so that trace and audit see the
rewritten syscall number, from Kees Cook"
* tag 'core_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
core/entry: Report syscall correctly for trace and audit
Pull locking fixes from Borislav Petkov:
"Two fixes from the locking/urgent pile:
- Fix lockdep's detection of "USED" <- "IN-NMI" inversions (Peter
Zijlstra)
- Make percpu-rwsem operations on the semaphore's ->read_count
IRQ-safe because it can be used in an IRQ context (Hou Tao)"
* tag 'locking_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/percpu-rwsem: Use this_cpu_{inc,dec}() for read_count
locking/lockdep: Fix "USED" <- "IN-NMI" inversions
Pull EFI fix from Borislav Petkov:
"Ensure that the EFI bootloader control module only probes successfully
on systems that support the EFI SetVariable runtime service"
[ Tag and commit from Ard Biesheuvel, forwarded by Borislav ]
* tag 'efi-urgent-for-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: efibc: check for efivars write capability
Pull x86 fixes from Borislav Petkov:
- A defconfig fix (Daniel Díaz)
- Disable relocation relaxation for the compressed kernel when not
built as -pie as in that case kernels built with clang and linked
with LLD fail to boot due to the linker optimizing some instructions
in non-PIE form; the gory details in the commit message (Arvind
Sankar)
- A fix for the "bad bp value" warning issued by the frame-pointer
unwinder (Josh Poimboeuf)
* tag 'x86_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/unwind/fp: Fix FP unwinding in ret_from_fork
x86/boot/compressed: Disable relocation relaxation
x86/defconfigs: Explicitly unset CONFIG_64BIT in i386_defconfig
Pull libnvdimm fixes from Dan Williams:
"A handful of fixes to address a string of mistakes in the mechanism
for device-mapper to determine if its component devices are dax
capable.
- Fix an original bug in device-mapper table reference counting when
interrogating dax capability in the component device. This bug was
hidden by the following bug.
- Fix device-mapper to use the proper helper (dax_supported() instead
of the leaf helper generic_fsdax_supported()) to determine dax
operation of a stacked block device configuration. The original
implementation is only valid for one level of dax-capable block
device stacking. This bug was discovered while fixing the below
regression.
- Fix an infinite recursion regression introduced by broken attempts
to quiet the generic_fsdax_supported() path and make it bail out
before logging "dax capability not found" errors"
* tag 'libnvdimm-fixes-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: Fix stack overflow when mounting fsdax pmem device
dm: Call proper helper to determine dax support
dm/dax: Fix table reference counts
Pull RISC-V fixes from Palmer Dabbelt:
- A fix for a lockdep issue to avoid an asserting triggering during
early boot. There shouldn't be any incorrect behavior as the system
isn't concurrent at the time.
- The addition of a missing fence when installing early fixmap
mappings.
- A corretion to the K210 device tree's interrupt map.
- A fix for M-mode timer handling on the K210.
* tag 'riscv-for-linus-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Resurrect the MMIO timer implementation for M-mode systems
riscv: Fix Kendryte K210 device tree
riscv: Add sfence.vma after early page table changes
RISC-V: Take text_mutex in ftrace_init_nop()
Pull USB/Thunderbolt fixes from Greg KH:
"Here are some small USB and one Thunderbolt driver fixes.
Nothing major at all, just some fixes for reported issues, and a quirk
addition:
- typec fixes
- UAS disconnect fix
- usblp race fix
- ehci-hcd modversions build fix
- ignore wakeup quirk table addition
- thunderbolt DROM read fix
All of these have been in linux-next with no reported issues"
* tag 'usb-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usblp: fix race between disconnect() and read()
ehci-hcd: Move include to keep CRC stable
usb: typec: intel_pmc_mux: Handle SCU IPC error conditions
USB: quirks: Add USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk for BYD zhaoxin notebook
USB: UAS: fix disconnect by unplugging a hub
usb: typec: ucsi: Prevent mode overrun
usb: typec: ucsi: acpi: Increase command completion timeout value
thunderbolt: Retry DROM read once if parsing fails
Pull tty/serial/fbcon fixes from Greg KH:
"Here are some small tty/serial and one more fbcon fix.
They include:
- serial core locking regression fixes
- new device ids for 8250_pci driver
- fbcon fix for syzbot found issue
All have been in linux-next with no reported issues"
* tag 'tty-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
fbcon: Fix user font detection test at fbcon_resize().
serial: 8250_pci: Add Realtek 816a and 816b
serial: core: fix console port-lock regression
serial: core: fix port-lock initialisation
Pull EDAC fixes from Borislav Petkov:
"Two fixes for resulting from CONFIG_DEBUG_TEST_DRIVER_REMOVE=y
experiments:
- complete a previous fix to reset a local structure containing
scanned system data properly so that the driver rescans, as it
should, on a second load.
- address a refcount underflow due to not paying attention to the
driver whitelest on unregister"
* tag 'edac_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC/ghes: Check whether the driver is on the safe list correctly
EDAC/ghes: Clear scanned data on unload
