VLAN register accesses on the MAC side require the PHY RX clock to be
active. When the network interface is down, the PHY is suspended and
the RX clock is unavailable, causing VLAN operations to fail with
timeouts.
The VLAN core automatically removes VID 0 after the interface goes down
and re-adds it when it comes back up, so these timeouts happen during
normal interface down/up:
# ip link set end1 down
renesas-gbeth 15c40000.ethernet end1: Timeout accessing MAC_VLAN_Tag_Filter
renesas-gbeth 15c40000.ethernet end1: failed to kill vid 0081/0
Adding VLANs while the interface is down also fails:
# ip link add link end1 name end1.10 type vlan id 10
renesas-gbeth 15c40000.ethernet end1: Timeout accessing MAC_VLAN_Tag_Filter
RTNETLINK answers: Device or resource busy
To fix this, check if the interface is up before accessing VLAN registers.
The software state is always kept up to date regardless of interface state.
When the interface is brought up, stmmac_vlan_restore() is called
to write the VLAN state to hardware.
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-5-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When the network interface is opened or resumed, a DMA reset is performed,
which resets all hardware state, including VLAN state. Currently, only
the resume path is restoring the VLAN state via
stmmac_restore_hw_vlan_rx_fltr(), but that is incomplete: the VLAN hash
table and the VLAN_TAG control bits are not restored.
Therefore, add stmmac_vlan_restore(), which restores the full VLAN
state by updating both the HW filter entries and the hash table, and
call it from both the open and resume paths.
The VLAN restore is moved outside of phylink_rx_clk_stop_block/unblock
in the resume path because receive clock stop is already disabled when
stmmac supports VLAN.
Also, remove the hash readback code in vlan_restore_hw_rx_fltr() that
attempts to restore VTHM by reading VLAN_HASH_TABLE, as it always reads
zero after DMA reset, making it dead code.
Fixes: 3cd1cfcba2 ("net: stmmac: Implement VLAN Hash Filtering in XGMAC")
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-4-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The double VLAN bits (EDVLP, ESVL, DOVLTC) are handled inconsistently
between the two vlan_update_hash() implementations:
- dwxgmac2_update_vlan_hash() explicitly clears the double VLAN bits when
is_double is false, meaning that adding a 802.1Q VLAN will disable
double VLAN mode:
$ ip link add link eth0 name eth0.200 type vlan id 200 protocol 802.1ad
$ ip link add link eth0 name eth0.100 type vlan id 100
# Double VLAN bits no longer set
- vlan_update_hash() sets these bits and only clears them when the last
VLAN has been removed, so double VLAN mode remains enabled even after all
802.1AD VLANs are removed.
Address both issues by tracking the number of active 802.1AD VLANs in
priv->num_double_vlans. Pass this count to stmmac_vlan_update() so both
implementations correctly set the double VLAN bits when any 802.1AD
VLAN is active, and clear them only when none remain.
Also update vlan_update_hash() to explicitly clear the double VLAN bits
when is_double is false, matching the dwxgmac2 behavior.
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-3-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
stmmac_vlan_rx_add_vid() updates active_vlans and the VLAN hash
register before writing the HW filter entry. If the filter write
fails, it leaves a stale VID in active_vlans and the hash register.
stmmac_vlan_rx_kill_vid() has the reverse problem: it clears
active_vlans before removing the HW filter. On failure, the VID is
gone from active_vlans but still present in the HW filter table.
To fix this, reorder the operations to update the hash table first,
then attempt the HW filter operation. If the HW filter fails, roll
back both the active_vlans bitmap and the hash table by calling
stmmac_vlan_update() again.
Fixes: ed64639bc1 ("net: stmmac: Add support for VLAN Rx filtering")
Signed-off-by: Ovidiu Panait <ovidiu.panait.rb@renesas.com>
Link: https://patch.msgid.link/20260303145828.7845-2-ovidiu.panait.rb@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2026-03-03 (ice, libie, iavf, igb, igc)
Larysa removes VF restriction for LLDP filters on ice to allow for LLDP
traffic to reach the correct destination.
Jakub adds retry mechanism for AdminQ Read/Write SFF EEPROM call to
follow hardware specification on ice.
Zilin Guan adds cleanup path to free XDP rings on failure in
ice_set_ringparam().
Michal bypasses firmware logging unroll in libie when it isn't supported.
Kohei Enju fixes iavf to take into account hardware MTU support when
setting max MTU values.
Vivek Behera fixes issues on igb and igc using incorrect IRQs when Tx/Rx
queues do not share the same IRQ.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
igc: Fix trigger of incorrect irq in igc_xsk_wakeup function
igb: Fix trigger of incorrect irq in igb_xsk_wakeup
iavf: fix netdev->max_mtu to respect actual hardware limit
libie: don't unroll if fwlog isn't supported
ice: Fix memory leak in ice_set_ringparam()
ice: fix retry for AQ command 0x06EE
ice: reintroduce retry mechanism for indirect AQ
ice: fix adding AQ LLDP filter for VF
====================
Link: https://patch.msgid.link/20260303231155.2895065-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Matthieu Baerts says:
====================
mptcp: misc fixes for v7.0-rc2
Here are various unrelated fixes:
- Patch 1: avoid bufferbloat in simult_flows selftest which can cause
instabilities. A fix for v5.10.
- Patches 2-3: reduce RM_ADDR lost by not sending it over the same
subflow as the one being removed, if possible. A fix for v5.13.
- Patches 4-5: avoid a WARN when using signal + subflow endpoints with a
subflow limit of 0, and removing such endpoints during an active
connection. A fix for v5.17.
====================
Link: https://patch.msgid.link/20260303-net-mptcp-misc-fixes-7-0-rc2-v1-0-4b5462b6f016@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This validates the previous commit: endpoints with both the signal and
subflow flags should always be marked as used even if it was not
possible to create new subflows due to the MPTCP PM limits.
For this test, an extra endpoint is created with both the signal and the
subflow flags, and limits are set not to create extra subflows. In this
case, an ADD_ADDR is sent, but no subflows are created. Still, the local
endpoint is marked as used, and no warning is fired when removing the
endpoint, after having sent a RM_ADDR.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
Fixes: 85df533a78 ("mptcp: pm: do not ignore 'subflow' if 'signal' flag is also set")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260303-net-mptcp-misc-fixes-7-0-rc2-v1-5-4b5462b6f016@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzkaller managed to find a combination of actions that was generating
this warning:
msk->pm.local_addr_used == 0
WARNING: net/mptcp/pm_kernel.c:1071 at __mark_subflow_endp_available net/mptcp/pm_kernel.c:1071 [inline], CPU#1: syz.2.17/961
WARNING: net/mptcp/pm_kernel.c:1071 at mptcp_nl_remove_subflow_and_signal_addr net/mptcp/pm_kernel.c:1103 [inline], CPU#1: syz.2.17/961
WARNING: net/mptcp/pm_kernel.c:1071 at mptcp_pm_nl_del_addr_doit+0x81d/0x8f0 net/mptcp/pm_kernel.c:1210, CPU#1: syz.2.17/961
Modules linked in:
CPU: 1 UID: 0 PID: 961 Comm: syz.2.17 Not tainted 6.19.0-08368-gfafda3b4b06b #22 PREEMPT(full)
Hardware name: QEMU Ubuntu 25.10 PC v2 (i440FX + PIIX, + 10.1 machine, 1996), BIOS 1.17.0-debian-1.17.0-1build1 04/01/2014
RIP: 0010:__mark_subflow_endp_available net/mptcp/pm_kernel.c:1071 [inline]
RIP: 0010:mptcp_nl_remove_subflow_and_signal_addr net/mptcp/pm_kernel.c:1103 [inline]
RIP: 0010:mptcp_pm_nl_del_addr_doit+0x81d/0x8f0 net/mptcp/pm_kernel.c:1210
Code: 89 c5 e8 46 30 6f fe e9 21 fd ff ff 49 83 ed 80 e8 38 30 6f fe 4c 89 ef be 03 00 00 00 e8 db 49 df fe eb ac e8 24 30 6f fe 90 <0f> 0b 90 e9 1d ff ff ff e8 16 30 6f fe eb 05 e8 0f 30 6f fe e8 9a
RSP: 0018:ffffc90001663880 EFLAGS: 00010293
RAX: ffffffff82de1a6c RBX: 0000000000000000 RCX: ffff88800722b500
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ffff8880158b22d0 R08: 0000000000010425 R09: ffffffffffffffff
R10: ffffffff82de18ba R11: 0000000000000000 R12: ffff88800641a640
R13: ffff8880158b1880 R14: ffff88801ec3c900 R15: ffff88800641a650
FS: 00005555722c3500(0000) GS:ffff8880f909d000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f66346e0f60 CR3: 000000001607c000 CR4: 0000000000350ef0
Call Trace:
<TASK>
genl_family_rcv_msg_doit+0x117/0x180 net/netlink/genetlink.c:1115
genl_family_rcv_msg net/netlink/genetlink.c:1195 [inline]
genl_rcv_msg+0x3a8/0x3f0 net/netlink/genetlink.c:1210
netlink_rcv_skb+0x16d/0x240 net/netlink/af_netlink.c:2550
genl_rcv+0x28/0x40 net/netlink/genetlink.c:1219
netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline]
netlink_unicast+0x3e9/0x4c0 net/netlink/af_netlink.c:1344
netlink_sendmsg+0x4aa/0x5b0 net/netlink/af_netlink.c:1894
sock_sendmsg_nosec net/socket.c:727 [inline]
__sock_sendmsg+0xc9/0xf0 net/socket.c:742
____sys_sendmsg+0x272/0x3b0 net/socket.c:2592
___sys_sendmsg+0x2de/0x320 net/socket.c:2646
__sys_sendmsg net/socket.c:2678 [inline]
__do_sys_sendmsg net/socket.c:2683 [inline]
__se_sys_sendmsg net/socket.c:2681 [inline]
__x64_sys_sendmsg+0x110/0x1a0 net/socket.c:2681
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x143/0x440 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f66346f826d
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 e8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffc83d8bdc8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f6634985fa0 RCX: 00007f66346f826d
RDX: 00000000040000b0 RSI: 0000200000000740 RDI: 0000000000000007
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6634985fa8
R13: 00007f6634985fac R14: 0000000000000000 R15: 0000000000001770
</TASK>
The actions that caused that seem to be:
- Set the MPTCP subflows limit to 0
- Create an MPTCP endpoint with both the 'signal' and 'subflow' flags
- Create a new MPTCP connection from a different address: an ADD_ADDR
linked to the MPTCP endpoint will be sent ('signal' flag), but no
subflows is initiated ('subflow' flag)
- Remove the MPTCP endpoint
In this case, msk->pm.local_addr_used has been kept to 0 -- because no
subflows have been created -- but the corresponding bit in
msk->pm.id_avail_bitmap has been cleared when the ADD_ADDR has been
sent. This later causes a splat when removing the MPTCP endpoint because
msk->pm.local_addr_used has been kept to 0.
Now, if an endpoint has both the signal and subflow flags, but it is not
possible to create subflows because of the limits or the c-flag case,
then the local endpoint counter is still incremented: the endpoint is
used at the end. This avoids issues later when removing the endpoint and
calling __mark_subflow_endp_available(), which expects
msk->pm.local_addr_used to have been previously incremented if the
endpoint was marked as used according to msk->pm.id_avail_bitmap.
Note that signal_and_subflow variable is reset to false when the limits
and the c-flag case allows subflows creation. Also, local_addr_used is
only incremented for non ID0 subflows.
Fixes: 85df533a78 ("mptcp: pm: do not ignore 'subflow' if 'signal' flag is also set")
Cc: stable@vger.kernel.org
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/613
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260303-net-mptcp-misc-fixes-7-0-rc2-v1-4-4b5462b6f016@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This validates the previous commit: RM_ADDR were sent over the first
found active subflow which could be the same as the one being removed.
It is more likely to loose this notification.
For this check, RM_ADDR are explicitly dropped when trying to send them
over the initial subflow, when removing the endpoint attached to it. If
it is dropped, the test will complain because some RM_ADDR have not been
received.
Note that only the RM_ADDR are dropped, to allow the linked subflow to
be quickly and cleanly closed. To only drop those RM_ADDR, a cBPF byte
code is used. If the IPTables commands fail, that's OK, the tests will
continue to pass, but not validate this part. This can be ignored:
another subtest fully depends on such command, and will be marked as
skipped.
The 'Fixes' tag here below is the same as the one from the previous
commit: this patch here is not fixing anything wrong in the selftests,
but it validates the previous fix for an issue introduced by this commit
ID.
Fixes: 8dd5efb1f9 ("mptcp: send ack for rm_addr")
Cc: stable@vger.kernel.org
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260303-net-mptcp-misc-fixes-7-0-rc2-v1-3-4b5462b6f016@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RM_ADDR are sent over an active subflow, the first one in the subflows
list. There is then a high chance the initial subflow is picked. With
the in-kernel PM, when an endpoint is removed, a RM_ADDR is sent, then
linked subflows are closed. This is done for each active MPTCP
connection.
MPTCP endpoints are likely removed because the attached network is no
longer available or usable. In this case, it is better to avoid sending
this RM_ADDR over the subflow that is going to be removed, but prefer
sending it over another active and non stale subflow, if any.
This modification avoids situations where the other end is not notified
when a subflow is no longer usable: typically when the endpoint linked
to the initial subflow is removed, especially on the server side.
Fixes: 8dd5efb1f9 ("mptcp: send ack for rm_addr")
Cc: stable@vger.kernel.org
Reported-by: Frank Lorenz <lorenz-frank@web.de>
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/612
Reviewed-by: Mat Martineau <martineau@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260303-net-mptcp-misc-fixes-7-0-rc2-v1-2-4b5462b6f016@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
By default, the netem qdisc can keep up to 1000 packets under its belly
to deal with the configured rate and delay. The simult flows test-case
simulates very low speed links, to avoid problems due to slow CPUs and
the TCP stack tend to transmit at a slightly higher rate than the
(virtual) link constraints.
All the above causes a relatively large amount of packets being enqueued
in the netem qdiscs - the longer the transfer, the longer the queue -
producing increasingly high TCP RTT samples and consequently increasingly
larger receive buffer size due to DRS.
When the receive buffer size becomes considerably larger than the needed
size, the tests results can flake, i.e. because minimal inaccuracy in the
pacing rate can lead to a single subflow usage towards the end of the
connection for a considerable amount of data.
Address the issue explicitly setting netem limits suitable for the
configured link speeds and unflake all the affected tests.
Fixes: 1a418cb8e8 ("mptcp: simult flow self-tests")
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20260303-net-mptcp-misc-fixes-7-0-rc2-v1-1-4b5462b6f016@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski says:
====================
nfc: fix leaks and races surfaced by NIPA
I recently added the nci test to NIPA. Somewhat surprisingly it runs
without much settup but hits kmemleaks fairly often. Fix a handful of
issues to make the test pass in a stable way.
====================
Link: https://patch.msgid.link/20260303162346.2071888-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In rawsock_release(), cancel any pending tx_work and purge the write
queue before orphaning the socket. rawsock_tx_work runs on the system
workqueue and calls nfc_data_exchange which dereferences the NCI
device. Without synchronization, tx_work can race with socket and
device teardown when a process is killed (e.g. by SIGKILL), leading
to use-after-free or leaked references.
Set SEND_SHUTDOWN first so that if tx_work is already running it will
see the flag and skip transmitting, then use cancel_work_sync to wait
for any in-progress execution to finish, and finally purge any
remaining queued skbs.
Fixes: 23b7869c0f ("NFC: add the NFC socket raw protocol")
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20260303162346.2071888-6-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move clear_bit(NCI_DATA_EXCHANGE) before invoking the data exchange
callback in nci_data_exchange_complete().
The callback (e.g. rawsock_data_exchange_complete) may immediately
schedule another data exchange via schedule_work(tx_work). On a
multi-CPU system, tx_work can run and reach nci_transceive() before
the current nci_data_exchange_complete() clears the flag, causing
test_and_set_bit(NCI_DATA_EXCHANGE) to return -EBUSY and the new
transfer to fail.
This causes intermittent flakes in nci/nci_dev in NIPA:
# # RUN NCI.NCI1_0.t4t_tag_read ...
# # t4t_tag_read: Test terminated by timeout
# # FAIL NCI.NCI1_0.t4t_tag_read
# not ok 3 NCI.NCI1_0.t4t_tag_read
Fixes: 38f04c6b1b ("NFC: protect nci_data_exchange transactions")
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20260303162346.2071888-5-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
digital_in_send() takes ownership of the skb passed by the caller
(nfc_data_exchange), make sure it's freed on all error paths.
Found looking around the real driver for similar bugs to the one
just fixed in nci.
Fixes: 2c66daecc4 ("NFC Digital: Add NFC-A technology support")
Reviewed-by: Joe Damato <joe@dama.to>
Link: https://patch.msgid.link/20260303162346.2071888-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
binding->dev is protected on the write-side in
mp_dmabuf_devmem_uninstall() against concurrent writes, but due to the
concurrent bare reads in net_devmem_get_binding() and
validate_xmit_unreadable_skb() it should be wrapped in a
READ_ONCE/WRITE_ONCE pair to make sure no compiler optimizations play
with the underlying register in unforeseen ways.
Doesn't present a critical bug because the known compiler optimizations
don't result in bad behavior. There is no tearing on u64, and load
omissions/invented loads would only break if additional binding->dev
references were inlined together (they aren't right now).
This just more strictly follows the linux memory model (i.e.,
"Lock-Protected Writes With Lockless Reads" in
tools/memory-model/Documentation/access-marking.txt).
Fixes: bd61848900 ("net: devmem: Implement TX path")
Signed-off-by: Bobby Eshleman <bobbyeshleman@meta.com>
Link: https://patch.msgid.link/20260302-devmem-membar-fix-v2-1-5b33c9cbc28b@meta.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When/if a NIC resets, queues are deactivated by dev_deactivate_many(),
then reactivated when the reset operation completes.
fq_reset() removes all the skbs from various queues.
If we do not clear q->band_pkt_count[], these counters keep growing
and can eventually reach sch->limit, preventing new packets to be queued.
Many thanks to Praveen for discovering the root cause.
Fixes: 29f834aa32 ("net_sched: sch_fq: add 3 bands and WRR scheduling")
Diagnosed-by: Praveen Kaligineedi <pkaligineedi@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20260304015640.961780-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts 28ee1b746f ("secure_seq: downgrade to per-host timestamp offsets")
tcp_tw_recycle went away in 2017.
Zhouyan Deng reported off-path TCP source port leakage via
SYN cookie side-channel that can be fixed in multiple ways.
One of them is to bring back TCP ports in TS offset randomization.
As a bonus, we perform a single siphash() computation
to provide both an ISN and a TS offset.
Fixes: 28ee1b746f ("secure_seq: downgrade to per-host timestamp offsets")
Reported-by: Zhouyan Deng <dengzhouyan_nwpu@163.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@google.com>
Acked-by: Florian Westphal <fw@strlen.de>
Link: https://patch.msgid.link/20260302205527.1982836-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When shrinking the number of real tx queues,
netif_set_real_num_tx_queues() calls qdisc_reset_all_tx_gt() to flush
qdiscs for queues which will no longer be used.
qdisc_reset_all_tx_gt() currently serializes qdisc_reset() with
qdisc_lock(). However, for lockless qdiscs, the dequeue path is
serialized by qdisc_run_begin/end() using qdisc->seqlock instead, so
qdisc_reset() can run concurrently with __qdisc_run() and free skbs
while they are still being dequeued, leading to UAF.
This can easily be reproduced on e.g. virtio-net by imposing heavy
traffic while frequently changing the number of queue pairs:
iperf3 -ub0 -c $peer -t 0 &
while :; do
ethtool -L eth0 combined 1
ethtool -L eth0 combined 2
done
With KASAN enabled, this leads to reports like:
BUG: KASAN: slab-use-after-free in __qdisc_run+0x133f/0x1760
...
Call Trace:
<TASK>
...
__qdisc_run+0x133f/0x1760
__dev_queue_xmit+0x248f/0x3550
ip_finish_output2+0xa42/0x2110
ip_output+0x1a7/0x410
ip_send_skb+0x2e6/0x480
udp_send_skb+0xb0a/0x1590
udp_sendmsg+0x13c9/0x1fc0
...
</TASK>
Allocated by task 1270 on cpu 5 at 44.558414s:
...
alloc_skb_with_frags+0x84/0x7c0
sock_alloc_send_pskb+0x69a/0x830
__ip_append_data+0x1b86/0x48c0
ip_make_skb+0x1e8/0x2b0
udp_sendmsg+0x13a6/0x1fc0
...
Freed by task 1306 on cpu 3 at 44.558445s:
...
kmem_cache_free+0x117/0x5e0
pfifo_fast_reset+0x14d/0x580
qdisc_reset+0x9e/0x5f0
netif_set_real_num_tx_queues+0x303/0x840
virtnet_set_channels+0x1bf/0x260 [virtio_net]
ethnl_set_channels+0x684/0xae0
ethnl_default_set_doit+0x31a/0x890
...
Serialize qdisc_reset_all_tx_gt() against the lockless dequeue path by
taking qdisc->seqlock for TCQ_F_NOLOCK qdiscs, matching the
serialization model already used by dev_reset_queue().
Additionally clear QDISC_STATE_NON_EMPTY after reset so the qdisc state
reflects an empty queue, avoiding needless re-scheduling.
Fixes: 6b3ba9146f ("net: sched: allow qdiscs to handle locking")
Signed-off-by: Koichiro Den <den@valinux.co.jp>
Link: https://patch.msgid.link/20260228145307.3955532-1-den@valinux.co.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Marc Kleine-Budde says:
====================
pull-request: can 2026-03-02
The first 2 patches are by Oliver Hartkopp. The first fixes the
locking for CAN Broadcast Manager op runtime updates, the second fixes
the packet statisctics for the CAN dummy driver.
Alban Bedel's patch fixes a potential problem in the error path of the
mcp251x's ndo_open callback.
A patch by Ziyi Guo add USB endpoint type validation to the esd_usb
driver.
The next 6 patches are by Greg Kroah-Hartman and fix URB data parsing
for the ems_usb and ucan driver, fix URB anchoring in the etas_es58x,
and in the f81604 driver fix URB data parsing, add URB error handling
and fix URB anchoring.
A patch by me targets the gs_usb driver and fixes interoperability
with the CANable-2.5 firmware by always configuring the bit rate
before starting the device.
The last patch is by Frank Li and fixes a CHECK_DTBS warning for the
nxp,sja1000 dt-binding.
* tag 'linux-can-fixes-for-7.0-20260302' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
dt-bindings: net: can: nxp,sja1000: add reference to mc-peripheral-props.yaml
can: gs_usb: gs_can_open(): always configure bitrates before starting device
can: usb: f81604: correctly anchor the urb in the read bulk callback
can: usb: f81604: handle bulk write errors properly
can: usb: f81604: handle short interrupt urb messages properly
can: usb: etas_es58x: correctly anchor the urb in the read bulk callback
can: ucan: Fix infinite loop from zero-length messages
can: ems_usb: ems_usb_read_bulk_callback(): check the proper length of a message
can: esd_usb: add endpoint type validation
can: mcp251x: fix deadlock in error path of mcp251x_open
can: dummy_can: dummy_can_init(): fix packet statistics
can: bcm: fix locking for bcm_op runtime updates
====================
Link: https://patch.msgid.link/20260302152755.1700177-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Johannes Berg says:
====================
Some more fixes:
- mt76 gets three almost identical new length checks
- cw1200 & ti: locking fixes
- mac80211 has a fix for the recent EML frame handling
- rsi driver no longer oddly responds to config, which
had triggered a warning in mac80211
- ath12k has two fixes for station statistics handling
* tag 'wireless-2026-03-04' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: mt76: Fix possible oob access in mt76_connac2_mac_write_txwi_80211()
wifi: mt76: mt7925: Fix possible oob access in mt7925_mac_write_txwi_80211()
wifi: mt76: mt7996: Fix possible oob access in mt7996_mac_write_txwi_80211()
wifi: wlcore: Fix a locking bug
wifi: cw1200: Fix locking in error paths
wifi: mac80211: fix missing ieee80211_eml_params member initialization
wifi: rsi: Don't default to -EOPNOTSUPP in rsi_mac80211_config
wifi: ath12k: fix station lookup failure when disconnecting from AP
wifi: ath12k: use correct pdev id when requesting firmware stats
====================
Link: https://patch.msgid.link/20260304112500.169639-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
list_categories() builds a set directly from the 'category'
field of each test case. Since 'category' is a list,
set(map(...)) attempts to insert lists into a set, which
raises:
TypeError: unhashable type: 'list'
Flatten category lists and collect unique category names
using set.update() instead.
Signed-off-by: Naveen Anandhan <mr.navi8680@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgbe_powerdown() and xgbe_powerup() functions use spinlocks
(spin_lock_irqsave) while calling functions that may sleep:
- napi_disable() can sleep waiting for NAPI polling to complete
- flush_workqueue() can sleep waiting for pending work items
This causes a "BUG: scheduling while atomic" error during suspend/resume
cycles on systems using the AMD XGBE Ethernet controller.
The spinlock protection in these functions is unnecessary as these
functions are called from suspend/resume paths which are already serialized
by the PM core
Fix this by removing the spinlock. Since only code that takes this lock
is xgbe_powerdown() and xgbe_powerup(), remove it completely.
Fixes: c5aa9e3b81 ("amd-xgbe: Initial AMD 10GbE platform driver")
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Link: https://patch.msgid.link/20260302042124.1386445-1-Raju.Rangoju@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sysdata_release_enabled_show() checks SYSDATA_TASKNAME instead of
SYSDATA_RELEASE, causing the configfs release_enabled attribute to
reflect the taskname feature state rather than the release feature
state. This is a copy-paste error from the adjacent
sysdata_taskname_enabled_show() function.
The corresponding _store function already uses the correct
SYSDATA_RELEASE flag.
Fixes: 343f902270 ("netconsole: implement configfs for release_enabled")
Signed-off-by: Breno Leitao <leitao@debian.org>
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20260302-sysdata_release_fix-v1-1-e5090f677c7c@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
`struct sysctl_fib_multipath_hash_seed` contains two u32 fields
(user_seed and mp_seed), making it an 8-byte structure with a 4-byte
alignment requirement.
In `fib_multipath_hash_from_keys()`, the code evaluates the entire
struct atomically via `READ_ONCE()`:
mp_seed = READ_ONCE(net->ipv4.sysctl_fib_multipath_hash_seed).mp_seed;
While this silently works on GCC by falling back to unaligned regular
loads which the ARM64 kernel tolerates, it causes a fatal kernel panic
when compiled with Clang and LTO enabled.
Commit e35123d83e ("arm64: lto: Strengthen READ_ONCE() to acquire
when CONFIG_LTO=y") strengthens `READ_ONCE()` to use Load-Acquire
instructions (`ldar` / `ldapr`) to prevent compiler reordering bugs
under Clang LTO. Since the macro evaluates the full 8-byte struct,
Clang emits a 64-bit `ldar` instruction. ARM64 architecture strictly
requires `ldar` to be naturally aligned, thus executing it on a 4-byte
aligned address triggers a strict Alignment Fault (FSC = 0x21).
Fix the read side by moving the `READ_ONCE()` directly to the `u32`
member, which emits a safe 32-bit `ldar Wn`.
Furthermore, Eric Dumazet pointed out that `WRITE_ONCE()` on the entire
struct in `proc_fib_multipath_hash_set_seed()` is also flawed. Analysis
shows that Clang splits this 8-byte write into two separate 32-bit
`str` instructions. While this avoids an alignment fault, it destroys
atomicity and exposes a tear-write vulnerability. Fix this by
explicitly splitting the write into two 32-bit `WRITE_ONCE()`
operations.
Finally, add the missing `READ_ONCE()` when reading `user_seed` in
`proc_fib_multipath_hash_seed()` to ensure proper pairing and
concurrency safety.
Fixes: 4ee2a8cace ("net: ipv4: Add a sysctl to set multipath hash seed")
Signed-off-by: Yung Chih Su <yuuchihsu@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20260302060247.7066-1-yuuchihsu@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
l3mdev_master_dev_rcu() can return NULL when the slave device is being
un-slaved from a VRF. All other callers deal with this, but we lost
the fallback to loopback in ip6_rt_pcpu_alloc() -> ip6_rt_get_dev_rcu()
with commit 4832c30d54 ("net: ipv6: put host and anycast routes on
device with address").
KASAN: null-ptr-deref in range [0x0000000000000108-0x000000000000010f]
RIP: 0010:ip6_rt_pcpu_alloc (net/ipv6/route.c:1418)
Call Trace:
ip6_pol_route (net/ipv6/route.c:2318)
fib6_rule_lookup (net/ipv6/fib6_rules.c:115)
ip6_route_output_flags (net/ipv6/route.c:2607)
vrf_process_v6_outbound (drivers/net/vrf.c:437)
I was tempted to rework the un-slaving code to clear the flag first
and insert synchronize_rcu() before we remove the upper. But looks like
the explicit fallback to loopback_dev is an established pattern.
And I guess avoiding the synchronize_rcu() is nice, too.
Fixes: 4832c30d54 ("net: ipv6: put host and anycast routes on device with address")
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://patch.msgid.link/20260301194548.927324-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch addresses the issue where the igc_xsk_wakeup function
was triggering an incorrect IRQ for tx-0 when the i226 is configured
with only 2 combined queues or in an environment with 2 active CPU cores.
This prevented XDP Zero-copy send functionality in such split IRQ
configurations.
The fix implements the correct logic for extracting q_vectors saved
during rx and tx ring allocation and utilizes flags provided by the
ndo_xsk_wakeup API to trigger the appropriate IRQ.
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Fixes: 15fd021bc4 ("igc: Add Tx hardware timestamp request for AF_XDP zero-copy packet")
Signed-off-by: Vivek Behera <vivek.behera@siemens.com>
Reviewed-by: Jacob Keller <jacob.keller@intel.com>
Reviewed-by: Aleksandr loktinov <aleksandr.loktionov@intel.com>
Reviewed-by: Piotr Kwapulinski <piotr.kwapulinski@intel.com>
Reviewed-by: Song Yoong Siang <yoong.siang.song@intel.com>
Tested-by: Avigail Dahan <avigailx.dahan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current implementation in the igb_xsk_wakeup expects
the Rx and Tx queues to share the same irq. This would lead
to triggering of incorrect irq in split irq configuration.
This patch addresses this issue which could impact environments
with 2 active cpu cores
or when the number of queues is reduced to 2 or less
cat /proc/interrupts | grep eno2
167: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
0-edge eno2
168: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
1-edge eno2-rx-0
169: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
2-edge eno2-rx-1
170: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
3-edge eno2-tx-0
171: 0 0 0 0 IR-PCI-MSIX-0000:08:00.0
4-edge eno2-tx-1
Furthermore it uses the flags input argument to trigger either rx, tx or
both rx and tx irqs as specified in the ndo_xsk_wakeup api documentation
Fixes: 80f6ccf9f1 ("igb: Introduce XSK data structures and helpers")
Signed-off-by: Vivek Behera <vivek.behera@siemens.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Saritha Sanigani <sarithax.sanigani@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
iavf sets LIBIE_MAX_MTU as netdev->max_mtu, ignoring vf_res->max_mtu
from PF [1]. This allows setting an MTU beyond the actual hardware
limit, causing TX queue timeouts [2].
Set correct netdev->max_mtu using vf_res->max_mtu from the PF.
Note that currently PF drivers such as ice/i40e set the frame size in
vf_res->max_mtu, not MTU. Convert vf_res->max_mtu to MTU before setting
netdev->max_mtu.
[1]
# ip -j -d link show $DEV | jq '.[0].max_mtu'
16356
[2]
iavf 0000:00:05.0 enp0s5: NETDEV WATCHDOG: CPU: 1: transmit queue 0 timed out 5692 ms
iavf 0000:00:05.0 enp0s5: NIC Link is Up Speed is 10 Gbps Full Duplex
iavf 0000:00:05.0 enp0s5: NETDEV WATCHDOG: CPU: 6: transmit queue 3 timed out 5312 ms
iavf 0000:00:05.0 enp0s5: NIC Link is Up Speed is 10 Gbps Full Duplex
...
Fixes: 5fa4caff59 ("iavf: switch to Page Pool")
Signed-off-by: Kohei Enju <kohei@enjuk.jp>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In ice_set_ringparam, tx_rings and xdp_rings are allocated before
rx_rings. If the allocation of rx_rings fails, the code jumps to
the done label leaking both tx_rings and xdp_rings. Furthermore, if
the setup of an individual Rx ring fails during the loop, the code jumps
to the free_tx label which releases tx_rings but leaks xdp_rings.
Fix this by introducing a free_xdp label and updating the error paths to
ensure both xdp_rings and tx_rings are properly freed if rx_rings
allocation or setup fails.
Compile tested only. Issue found using a prototype static analysis tool
and code review.
Fixes: fcea6f3da5 ("ice: Add stats and ethtool support")
Fixes: efc2214b60 ("ice: Add support for XDP")
Signed-off-by: Zilin Guan <zilin@seu.edu.cn>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The referenced commit came from a misunderstanding of the FW LLDP filter
AQ (Admin Queue) command due to the error in the internal documentation.
Contrary to the assumptions in the original commit, VFs can be added and
deleted from this filter without any problems. Introduced dev_info message
proved to be useful, so reverting the whole commit does not make sense.
Without this fix, trusted VFs do not receive LLDP traffic, if there is an
AQ LLDP filter on PF. When trusted VF attempts to add an LLDP multicast
MAC address, the following message can be seen in dmesg on host:
ice 0000:33:00.0: Failed to add Rx LLDP rule on VSI 20 error: -95
Revert checking VSI type when adding LLDP filter through AQ.
Fixes: 4d5a1c4e6d ("ice: do not add LLDP-specific filter if not necessary")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
I was debugging a NIC driver when I noticed that when I enable
threaded busypoll, bpftrace hangs when starting up. dmesg showed:
rcu_tasks_wait_gp: rcu_tasks grace period number 85 (since boot) is 10658 jiffies old.
rcu_tasks_wait_gp: rcu_tasks grace period number 85 (since boot) is 40793 jiffies old.
rcu_tasks_wait_gp: rcu_tasks grace period number 85 (since boot) is 131273 jiffies old.
rcu_tasks_wait_gp: rcu_tasks grace period number 85 (since boot) is 402058 jiffies old.
INFO: rcu_tasks detected stalls on tasks:
00000000769f52cd: .N nvcsw: 2/2 holdout: 1 idle_cpu: -1/64
task:napi/eth2-8265 state:R running task stack:0 pid:48300 tgid:48300 ppid:2 task_flags:0x208040 flags:0x00004000
Call Trace:
<TASK>
? napi_threaded_poll_loop+0x27c/0x2c0
? __pfx_napi_threaded_poll+0x10/0x10
? napi_threaded_poll+0x26/0x80
? kthread+0xfa/0x240
? __pfx_kthread+0x10/0x10
? ret_from_fork+0x31/0x50
? __pfx_kthread+0x10/0x10
? ret_from_fork_asm+0x1a/0x30
</TASK>
The cause is that in threaded busypoll, the main loop is in
napi_threaded_poll rather than napi_threaded_poll_loop, where the
latter rarely iterates more than once within its loop. For
rcu_softirq_qs_periodic inside napi_threaded_poll_loop to report its
qs state, the last_qs must be 100ms behind, and this can't happen
because napi_threaded_poll_loop rarely iterates in threaded busypoll,
and each time napi_threaded_poll_loop is called last_qs is reset to
latest jiffies.
This patch changes so that in threaded busypoll, last_qs is saved
in the outer napi_threaded_poll, and whether busy_poll_last_qs
is NULL indicates whether napi_threaded_poll_loop is called for
busypoll. This way last_qs would not reset to latest jiffies on
each invocation of napi_threaded_poll_loop.
Fixes: c18d4b190a ("net: Extend NAPI threaded polling to allow kthread based busy polling")
Cc: stable@vger.kernel.org
Signed-off-by: YiFei Zhu <zhuyifei@google.com>
Reviewed-by: Samiullah Khawaja <skhawaja@google.com>
Link: https://patch.msgid.link/20260227221937.1060857-1-zhuyifei@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
syzbot reported a circular locking dependency in rds_tcp_tune() where
sk_net_refcnt_upgrade() is called while holding the socket lock:
======================================================
WARNING: possible circular locking dependency detected
======================================================
kworker/u10:8/15040 is trying to acquire lock:
ffffffff8e9aaf80 (fs_reclaim){+.+.}-{0:0},
at: __kmalloc_cache_noprof+0x4b/0x6f0
but task is already holding lock:
ffff88805a3c1ce0 (k-sk_lock-AF_INET6){+.+.}-{0:0},
at: rds_tcp_tune+0xd7/0x930
The issue occurs because sk_net_refcnt_upgrade() performs memory
allocation (via get_net_track() -> ref_tracker_alloc()) while the
socket lock is held, creating a circular dependency with fs_reclaim.
Fix this by moving sk_net_refcnt_upgrade() outside the socket lock
critical section. This is safe because the fields modified by the
sk_net_refcnt_upgrade() call (sk_net_refcnt, ns_tracker) are not
accessed by any concurrent code path at this point.
v2:
- Corrected fixes tag
- check patch line wrap nits
- ai commentary nits
Reported-by: syzbot+2e2cf5331207053b8106@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=2e2cf5331207053b8106
Fixes: 3a58f13a88 ("net: rds: acquire refcount on TCP sockets")
Signed-off-by: Allison Henderson <achender@kernel.org>
Link: https://patch.msgid.link/20260227202336.167757-1-achender@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jeff Johnson says:
==================
ath.git update for v7.0-rc3
Fix issues with ath12k station statistics requests.
==================
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
