Merge "aspeed defconfig for 4.7" from Joel Stanley:
This adds configurations used for testing Aspeed BMC SoCs, as well as adding
the v5 part to the multi defconfig.
* tag 'aspeed-for-4.7-defconfig' of https://github.com/shenki/linux:
arm/configs: Add Aspeed defconfig
arm/configs/multi_v5: Add Aspeed ast2400
Merge "Ux500 defconfig update for v4.7" from Linus Walleij:
- Remove the unused MACH_UX500_DT option from the multi_v7 defconfig
- Remove staging driver from u8500_defconfig
- Update sensor support in u8500_defconfig
* tag 'ux500-defconfig-armsoc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: u8500_defconfig: update sensor config
ARM: u8500_defconfig: remove staging from defconfig
ARM: multi_v7_defconfig: Remove unused Kconfig option MACH_UX500_DT
The Ux500 is using buffered IIO as the sensors support
IRQs. The BH1780 ambient light sensor was added to IIO,
so disable the old misc driver and activate the driver
in IIO.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Ux500 was enabling the staging drivers due to the RMI4
touchscreen driver, this is now properly upstream, so drop
this and the dead symbol for the old RMI4 hack from
the defconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Merge "i.MX defconfig updates for 4.7" from Shawn Guo:
- Update multi_v5_defconfig for i.MX21/27 and systemd support
- Update imx_v6_v7_defconfig to support devices found on various i.MX6
board: FT5x06 and TSC2004 touch, I2C GPIO, MICREL PHY and M41T80 RTC
* tag 'imx-defconfig-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: add CONFIG_MICREL_PHY
ARM: imx_v6_v7_defconfig: add CONFIG_I2C_GPIO
ARM: multi_v5_defconfig: Enable recommended options for systemd
ARM: multi_v5_defconfig: Enable support for MX21/MX27
ARM: imx_v6_v7_defconfig: add CONFIG_RTC_DRV_M41T80
ARM: imx_v6_v7_defconfig: add CONFIG_I2C_MUX_GPIO
ARM: imx_v6_v7_defconfig: add FT5x06 and TSC2004 touch support
Merge "ARM: tegra: Default configuration updates for v4.7-rc1" from Thierry Reding:
Enable the XUSB pad controller and XUSB controller drivers on the Tegra
and multi-v7 default configurations.
* tag 'tegra-for-4.7-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: multi_v7: Enable Tegra XUSB controller in defconfig
ARM: tegra: Enable XUSB controller in defconfig
Merge "DaVinci defconfig updates for v4.7" from Sekhar Nori:
Some defconfig updates to support systemd
based filesystems, SPI NOR and GPIO sysfs
entries.
* tag 'davinci-for-v4.7/defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci_all_defconfig: enable SPI and NOR as modules
ARM: davinci_all_defconfig: support systemd
ARM: davinci_all_defconfig: enable GPIO_SYSFS
This adds the Aspeed ast2400 BMC SoC to the build.
The SoC has six UARTs so we need to enable the appropriate options for
SERIAL_8250
Signed-off-by: Joel Stanley <joel@jms.id.au>
The driver for Micrel PHYs is required for the Apalis iMX6 module
plugged into a Ixora carrier board featuring an on-module Micrel
KSZ9031 Gigabit PHY.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GPIO-based bitbanging I2C driver is required to make HDMI work on
the Apalis iMX6 module plugged into a Ixora carrier board featuring a
DDC channel to read a screen's EDID being hooked up to regular GPIOs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the XUSB pad controller and XUSB controller (implementing an XHCI
interface) in the multi_v7 default configuration.
The XUSB pad controller is built-in because it is needed by PCIe, which
in turn provides the onboard ethernet used for network boot on a Jetson
TK1.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the XUSB pad controller and XUSB controller (implementing an XHCI
interface) in the Tegra default configuration.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Merge "Defconfig changes for omap2plus_defconfig for v4.7 merge window" from Tony Lindgren:
Mostly enable drivers used on various boards as loadable modules
where possible. Also one warning fix related to RXKAD changes
heading to v4.7. And run make save_defconfig to shrink down the
size a bit.
* tag 'omap-for-v4.7/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: Enable PWM and ir-rx51 as loadable modules
ARM: omap2plus_defconfig: Enable twl6030 USB phy as loadable module
ARM: omap2plus_defconfig: Fix warning due invalid RXKAD symbol value
ARM: omap2plus_defconfig: Update with make savedefconfig
ARM: omap2plus_defconfig: Enable MDIO Bus/PHY emulation support
ARM: omap2plus_defconfig: Enable DP83867 support
ARM: omap2plus_defconfig: Enable GPIO_TPIC2810
Merge "NXP LPC32xx defconfig updates for v4.7" from Vladimir Zapolskiy:
This includes savedefconfig update of lpc32xx_defconfig, which removes
a number of outdated config options, plus ARM PrimeCell PL17x memory
controller driver is enabled by default now, on LPC32xx boards the
controller is commonly used to access SDRAM and NOR.
* tag 'lpc32xx-defconfig-4.7' of git://github.com/vzapolskiy/linux-lpc32xx:
ARM: LPC32xx: add PL175 memory controller driver to defconfig
ARM: LPC32xx: defconfig update
Commit 648af7fca1 ("rxrpc: Absorb the rxkad security module") changed
the RXKAD Kconfig symbol from tristate to boolean but the commit didn't
update the omap2plus_defconfig that was enabling CONFIG_RXKAD as module.
This leads to the following warning when using the omap2plus_defconfig:
arch/arm/configs/omap2plus_defconfig:112:warning: symbol value 'm' invalid for RXKAD
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "Renesas ARM Based SoC Pci Defconfig Updates for v4.7" from Simon Horman:
* Remove Gen2 designation from Kconfig for R-Car PCIE driver
* tag 'renesas-pci-defconfig-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
PCI: rcar-pcie: Remove Gen2 designation from Kconfig
Merge "ARM: Keystone HOTPLUG and PSCI config update for 4.7" from Santosh Shilimkar
* tag 'keystone_config_for_4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: configs: keystone: Add CPU Hotplug related options
Merge "This pull request contains defconfig changes for Broadcom ARM-based SoCs"
from Florian Fainelli:
- Eric enables more BCM2835 peripherals in multi_v7_defconfig: watchdog, I2S,
switches from the sdhci-bcm2835 to the sdhci-iproc driver, DWC2 USB controller
- Eric also enables more BCM2835 peripherals in bcm2835_defconfig: VC4, NFS root
Power Management support, switching sdhci-bcm2835 for sdhci-iproc
* tag 'arm-soc/for-4.7/defconfig' of http://github.com/Broadcom/stblinux:
ARM: bcm2835: Enable NFS root support.
ARM: bcm2835: Enable the VC4 graphics driver in the defconfig
ARM: bcm2835: Enable CONFIG_PM.
ARM: bcm2835: Switch BCM2835 to sdhci-iproc.c for MMC
ARM: multi_v7_defconfig: Build in DWC2 USB support
ARM: multi_v7_defconfig: Switch BCM2835 to sdhci-iproc.c for MMC
ARM: multi_v7_defconfig: Add more BCM2835 support
Merge "mvebu defconfig for 4.7 (part 1)" from Gregory CLEMENT
- Use the new cryto engine(mv_cesa) in the mvebu and multi-arm
defcongig files
- Attach mvebu_*_defconfig to the mvebu maintainers
* tag 'mvebu-defconfig-4.7-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu_v5_defconfig: Switching to the new Marvell's cryptographic engine driver
ARM: multi_v7_defconfig: Enabling the new Marvell's cryptographic engine driver
MAINTAINERS: attach arch/arm/configs/mvebu_*_defconfig to relevant maintainers
ARM: mvebu_v7_defconfig: Enabling the new Marvell's cryptographic engine driver
This NAND controller device is used on UniPhier SoCs (and I know
it is also used on SoC FPGA).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "Defconfig (exynos and multi_v7) changes for Exynos based boards for v4.7" from Krzysztof Kozłowski:
1. Enable additional drivers for Trats2 board (Exynos4412).
2. Enable CPUFreq governors as modules.
* tag 'samsung-defconfig-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: multi_v7_defconfig: Enable CPUFreq governors as modules
ARM: exynos_defconfig: Enable CPUFreq governors as modules
ARM: exynos_defconfig: Enable Trats2 audio codec, touchscreen and sensors
Enable SPI driver and SPI NOR flash support as modules.
Tested with SPI NOR flash on DA850-EVM. Basic boot test only to confirm
NOR flash device detection.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
It appears that Gen2 is a misnomer for the R-Car PCIE driver
which also supports Gen 1 and Gen 3 SoCs. Accordingly, drop Gen 2
from the help text and Kconfig symbol.
Also, re-arange the Kconfig symbol name to use PCIE as the prefix.
This appears to be in keeping with other PCIE Kconfig symbols.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
The change enables build of ARM PrimeCell PL17x driver for LPC32xx
platform, the memory controller is commonly used to interface NOR
flash drives.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The change is a result of "make lpc32xx_defconfig; make savedefconfig"
run, a number of config options are removed:
CONFIG_BINFMT_AOUT=y -- not needed, legacy
CONFIG_FPE_NWFPE=y -- not needed, AEABI build
CONFIG_IPV6_PRIVACY=y -- removed build option
CONFIG_IPV6=y -- selected by default
CONFIG_MII=y -- not needed, board phys don't select library
CONFIG_MTD_CHAR=y -- removed build option
CONFIG_MTD_M25P80=y -- not needed, AT25 EEPROM driver is in use
CONFIG_USB_PHY=y -- selected by default
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
This enables the new driver for Marvell CESA crypto engines on all mvebu v5.
The old driver is no longer used, but it is still in the tree for fallback.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The arch/arm/configs/mvebu_*_defconfig currently don't belong to any
maintainer, so get_maintainer returns only information based on
commits, which is not completely accurate.
Therefore, this commit replaces a useless empty newline in MAINTAINERS
by a line attaching those defconfigs to the appropriate Marvell EBU
maintainers.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Highlights:
-----------
- Enable ST's HW Random number generator in multi_v7 defconfig
- Enable PWM regulator support in multi_v7 defconfig
- Enable ST's Power and Reset driver in multi_v7 defconfig
- Enable ST's PWM in multi_v7 defconfig
* tag 'sti-defconfig-for-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti:
ARM: multi_v7_defconfig: Enable ST's HW Random Number Generator
ARM: multi_v7_defconfig: Enable support for PWM Regulators
ARM: multi_v7_defconfig: Enable ST's Power Reset driver
ARM: multi_v7_defconfig: Enable ST's PWM driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Three types of display controller-drivers where added recently. The
Analogix Displayport variant and Designware MIPI DSI used for example
on the rk3288 as well as the Innosilicon HDMI controller used on the
rk3036.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
The displayport phy controls the output of the Analogix displayport
controller on Rockchip SoCs and is therefore one component to enable
veyron devices to use their internal display.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
MDIO Bus/PHY emulation with fixed speed/link PHYs will be used in
Baltos iR5221 devices to connect to ICPlus IP175D switch IC.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable DP83867 Ethernet phy for supporting networking on DRA72-EVM rev C
(SR2.0).
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the TI TPIC2810 8-Bit LED Driver with I2C Interface. This is used
in AM335x ICEv2 Boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Renesas ARM Based SoC Defconfig Updates for v4.7
* Enable I2C demultiplexer and slave eeprom in
shmobile and multi_v7defconfigs
* tag 'renesas-defconfig-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: defconfig: enable I2C demultiplexer and slave eeprom
ARM: multi_v7_defconfig: enable I2C demultiplexer and slave eeprom
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the config options needed to get CPU hotplug functional.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Enable FHANDLE, CGROUPS, BLK_DEV_BSG and DEVTMPFS as recommended by
systemd (which also matches the multi_v7 defconfig). Also enable IPV6,
which defaults to 'y' by now.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently only the ondemand and performance CPUFreq policy governors are
enabled in multi_v7 defconfig. But the other governors are also useful
for some cases, enable them to allow users change the default if needed.
The options are enabled as module to keep the kernel image size minimal.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Currently only the ondemand and performance CPUFreq policy governors are
enabled in the Exynos defconfig. But the other governors are also useful
for some cases, enable them to allow users change the default if needed.
The options are enabled as module to keep the kernel image size minimal.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The Exynos4412-based Trats2 board has Asahi Kasei AK 3-Axis
Magnetometer, CM36651 proximity/ambient light sensor, MMS114 touchscreen
and Wolfson Microelectronics WM1811 CODEC. Enable them in defconfig to
get some testing coverage and use its features.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
