Enable the second EHCI controller on the AST2600. Also add a line-name
for the GPIO that controls power to the USB port.
The power control is in place to allow the port to be disabled, for
those that are worried about rogue USB sticks.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the second EHCI controller on the AST2600. Also add a line-name
for the GPIO that controls power to the USB port.
The power control is in place to allow the port to be disabled, for
those that are worried about rogue USB sticks.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses the P10 processor so the OCC binding should reflect that.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the four SPI masters on each CFAM. Each master has four 128KB EEPROM
devices attached to it.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Adding pca9552 exposes the presence detect lines for the cards and
tca9554 exposes the presence details for the cards.
Signed-off-by: Jet Li <Jet.Li@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Initial introduction of AMD EthanolX platform equipped with an
Aspeed ast2500 BMC manufactured by AMD.
AMD EthanolX platform is an AMD customer reference board with an
Aspeed ast2500 BMC manufactured by AMD.
This adds AMD EthanolX device tree file including the flash layout
used by EthanolX BMC machines.
Signed-off-by: Supreeth Venkatesh <supreeth.venkatesh@amd.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
We have a 4-bus mux whose output is selected by two GPIO inputs. Wire it
up in the devicetree and ensure the output is enabled by hogging the
appropriate line.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable pwm_tacho device for fan control and monitoring in Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable ADC controller and corresponding voltage sensoring channels for
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Disable i2c bus #9, #10 and #13 as these i2c controllers are not used on
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Create all the i2c switches in device tree and use aliases to assign
child channels with consistent bus numbers.
Besides, "i2c-mux-idle-disconnect" is set for all the i2c switches to
avoid potential conflicts when multiple devices (beind the switches)
use the same device address.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
The signal is wired as active high on the first pass systems.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
GPIOP7 is used in the Rainier design to manage the state of a
microcontroller elsewhere in the system but its ball, Y23, is the
driver of the heartbeat LED on the ast2600-evb and the SoC defaults Y23
at power-on to the pulse-train behaviour used to drive the LED. This
causes much confusion for the micro in the Rainier system, so hog the
line as early as possible.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The hub FSI master can access the cfams on two other processors. Reflect
this by adding a second cfam to the first hub description.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Rainier uses GPIO B6 as the checkstop GPIO. Define the line-name
so that this GPIO can be found by name.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The attention handler will monitor the checkstop gpio via the character
device interface so it needs to not be defined.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the PCI-E root complex reset, correct the pcie-device property, and
add the Aspeed SCU interrupt controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Correct the pcie-device property, and add the Aspeed SCU interrupt
controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set smbus_en of IO expander to 1 in order to be able to read sensor.
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Pull SafeSetID update from Micah Morton:
"Add additional LSM hooks for SafeSetID
SafeSetID is capable of making allow/deny decisions for set*uid calls
on a system, and we want to add similar functionality for set*gid
calls.
The work to do that is not yet complete, so probably won't make it in
for v5.8, but we are looking to get this simple patch in for v5.8
since we have it ready.
We are planning on the rest of the work for extending the SafeSetID
LSM being merged during the v5.9 merge window"
* tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux:
security: Add LSM hooks to set*gid syscalls
The SafeSetID LSM uses the security_task_fix_setuid hook to filter
set*uid() syscalls according to its configured security policy. In
preparation for adding analagous support in the LSM for set*gid()
syscalls, we add the requisite hook here. Tested by putting print
statements in the security_task_fix_setgid hook and seeing them get hit
during kernel boot.
Signed-off-by: Thomas Cedeno <thomascedeno@google.com>
Signed-off-by: Micah Morton <mortonm@chromium.org>
Pull btrfs updates from David Sterba:
"This reverts the direct io port to iomap infrastructure of btrfs
merged in the first pull request. We found problems in invalidate page
that don't seem to be fixable as regressions or without changing iomap
code that would not affect other filesystems.
There are four reverts in total, but three of them are followup
cleanups needed to revert a43a67a2d7 cleanly. The result is the
buffer head based implementation of direct io.
Reverts are not great, but under current circumstances I don't see
better options"
* tag 'for-5.8-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Revert "btrfs: switch to iomap_dio_rw() for dio"
Revert "fs: remove dio_end_io()"
Revert "btrfs: remove BTRFS_INODE_READDIO_NEED_LOCK"
Revert "btrfs: split btrfs_direct_IO to read and write part"
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
This reverts commit a43a67a2d7.
This patch reverts the main part of switching direct io implementation
to iomap infrastructure. There's a problem in invalidate page that
couldn't be solved as regression in this development cycle.
The problem occurs when buffered and direct io are mixed, and the ranges
overlap. Although this is not recommended, filesystems implement
measures or fallbacks to make it somehow work. In this case, fallback to
buffered IO would be an option for btrfs (this already happens when
direct io is done on compressed data), but the change would be needed in
the iomap code, bringing new semantics to other filesystems.
Another problem arises when again the buffered and direct ios are mixed,
invalidation fails, then -EIO is set on the mapping and fsync will fail,
though there's no real error.
There have been discussions how to fix that, but revert seems to be the
least intrusive option.
Link: https://lore.kernel.org/linux-btrfs/20200528192103.xm45qoxqmkw7i5yl@fiona/
Signed-off-by: David Sterba <dsterba@suse.com>
On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS allmulti setting does not allow
unregistered mcast packets to pass.
This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
This path was missed by commit 9d1f644727 ("net: ethernet: ti: ale: fix
seeing unreg mcast packets with promisc and allmulti disabled").
Hence, fix it by taking into account ALE type in cpsw_ale_set_allmulti().
Fixes: 9d1f644727 ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ALE parameters structure is created on stack, so it has to be reset
before passing to cpsw_ale_create() to avoid garbage values.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2020-06-12
The following pull-request contains BPF updates for your *net* tree.
We've added 26 non-merge commits during the last 10 day(s) which contain
a total of 27 files changed, 348 insertions(+), 93 deletions(-).
The main changes are:
1) sock_hash accounting fix, from Andrey.
2) libbpf fix and probe_mem sanitizing, from Andrii.
3) sock_hash fixes, from Jakub.
4) devmap_val fix, from Jesper.
5) load_bytes_relative fix, from YiFei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Looking into the context (atomic!) and the error message should be dropped.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more cifs updates from Steve French:
"12 cifs/smb3 fixes, 2 for stable.
- add support for idsfromsid on create and chgrp/chown allowing
ability to save owner information more naturally for some workloads
- improve query info (getattr) when SMB3.1.1 posix extensions are
negotiated by using new query info level"
* tag '5.8-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
smb3: Add debug message for new file creation with idsfromsid mount option
cifs: fix chown and chgrp when idsfromsid mount option enabled
smb3: allow uid and gid owners to be set on create with idsfromsid mount option
smb311: Add tracepoints for new compound posix query info
smb311: add support for using info level for posix extensions query
smb311: Add support for lookup with posix extensions query info
smb311: Add support for SMB311 query info (non-compounded)
SMB311: Add support for query info using posix extensions (level 100)
smb3: add indatalen that can be a non-zero value to calculation of credit charge in smb2 ioctl
smb3: fix typo in mount options displayed in /proc/mounts
cifs: Add get_security_type_str function to return sec type.
smb3: extend fscache mount volume coherency check
I'm not convinced the script makes useful automaed help lines anyway,
but since we're trying to deprecate the use of "---help---" in Kconfig
files, let's fix the doc example code too.
See commit a7f7f6248d ("treewide: replace '---help---' in Kconfig
files with 'help'")
Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more Kbuild updates from Masahiro Yamada:
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
treewide: replace '---help---' in Kconfig files with 'help'
kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
samples: binderfs: really compile this sample and fix build issues
Pull more SCSI updates from James Bottomley:
"This is the set of changes collected since just before the merge
window opened. It's mostly minor fixes in drivers.
The one non-driver set is the three optical disk (sr) changes where
two are error path fixes and one is a helper conversion.
The big driver change is the hpsa compat_alloc_userspace rework by Al
so he can kill the remaining user. This has been tested and acked by
the maintainer"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
scsi: acornscsi: Fix an error handling path in acornscsi_probe()
scsi: storvsc: Remove memset before memory freeing in storvsc_suspend()
scsi: cxlflash: Remove an unnecessary NULL check
scsi: ibmvscsi: Don't send host info in adapter info MAD after LPM
scsi: sr: Fix sr_probe() missing deallocate of device minor
scsi: sr: Fix sr_probe() missing mutex_destroy
scsi: st: Convert convert get_user_pages() --> pin_user_pages()
scsi: target: Rename target_setup_cmd_from_cdb() to target_cmd_parse_cdb()
scsi: target: Fix NULL pointer dereference
scsi: target: Initialize LUN in transport_init_se_cmd()
scsi: target: Factor out a new helper, target_cmd_init_cdb()
scsi: hpsa: hpsa_ioctl(): Tidy up a bit
scsi: hpsa: Get rid of compat_alloc_user_space()
scsi: hpsa: Don't bother with vmalloc for BIG_IOCTL_Command_struct
scsi: hpsa: Lift {BIG_,}IOCTL_Command_struct copy{in,out} into hpsa_ioctl()
scsi: ufs: Remove redundant urgent_bkop_lvl initialization
scsi: ufs: Don't update urgent bkops level when toggling auto bkops
scsi: qedf: Remove redundant initialization of variable rc
scsi: mpt3sas: Fix memset() in non-RDPQ mode
scsi: iscsi: Fix reference count leak in iscsi_boot_create_kobj
...
Pull i2c updates from Wolfram Sang:
"I2C has quite some patches for you this time. I hope it is the move to
per-driver-maintainers which is now showing results. We will see.
The big news is two new drivers (Nuvoton NPCM and Qualcomm CCI),
larger refactoring of the Designware, Tegra, and PXA drivers, the
Cadence driver supports being a slave now, and there is support to
instanciate SPD eeproms for well-known cases (which will be
user-visible because the i801 driver supports it), and some
devm_platform_ioremap_resource() conversions which blow up the
diffstat.
Note that I applied the Nuvoton driver quite late, so some minor fixup
patches arrived during the merge window. I chose to apply them right
away because they were trivial"
* 'i2c/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (109 commits)
i2c: Drop stray comma in MODULE_AUTHOR statements
i2c: npcm7xx: npcm_i2caddr[] can be static
MAINTAINERS: npcm7xx: Add maintainer for Nuvoton NPCM BMC
i2c: npcm7xx: Fix a couple of error codes in probe
i2c: icy: Fix build with CONFIG_AMIGA_PCMCIA=n
i2c: npcm7xx: Remove unnecessary parentheses
i2c: npcm7xx: Add support for slave mode for Nuvoton
i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver
dt-bindings: i2c: npcm7xx: add NPCM I2C controller
i2c: pxa: don't error out if there's no pinctrl
i2c: add 'single-master' property to generic bindings
i2c: designware: Add Baikal-T1 System I2C support
i2c: designware: Move reg-space remapping into a dedicated function
i2c: designware: Retrieve quirk flags as early as possible
i2c: designware: Convert driver to using regmap API
i2c: designware: Discard Cherry Trail model flag
i2c: designware: Add Baytrail sem config DW I2C platform dependency
i2c: designware: slave: Set DW I2C core module dependency
i2c: designware: Use `-y` to build multi-object modules
dt-bindings: i2c: dw: Add Baikal-T1 SoC I2C controller
...
Pull more media updates from Mauro Carvalho Chehab:
- a set of atomisp patches. They remove several abstraction layers, and
fixes clang and gcc warnings (that were hidden via some macros that
were disabling 4 or 5 types of warnings there). There are also some
important fixes and sensor auto-detection on newer BIOSes via ACPI
_DCM tables.
- some fixes
* tag 'media/v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (95 commits)
media: rkvdec: Fix H264 scaling list order
media: v4l2-ctrls: Unset correct HEVC loop filter flag
media: videobuf2-dma-contig: fix bad kfree in vb2_dma_contig_clear_max_seg_size
media: v4l2-subdev.rst: correct information about v4l2 events
media: s5p-mfc: Properly handle dma_parms for the allocated devices
media: medium: cec: Make MEDIA_CEC_SUPPORT default to n if !MEDIA_SUPPORT
media: cedrus: Implement runtime PM
media: cedrus: Program output format during each run
media: atomisp: improve ACPI/DMI detection logs
media: Revert "media: atomisp: add Asus Transform T101HA ACPI vars"
media: Revert "media: atomisp: Add some ACPI detection info"
media: atomisp: improve sensor detection code to use _DSM table
media: atomisp: get rid of an iomem abstraction layer
media: atomisp: get rid of a string_support.h abstraction layer
media: atomisp: use strscpy() instead of less secure variants
media: atomisp: set DFS to MAX if sensor doesn't report fps
media: atomisp: use different dfs failed messages
media: atomisp: change the detection of ISP2401 at runtime
media: atomisp: use macros from intel-family.h
media: atomisp: don't set hpll_freq twice with different values
...
Pull libnvdimm updates from Dan Williams:
"Small collection of cleanups to rework usage of ->queuedata and the
GUID api"
* tag 'libnvdimm-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nvdimm/pmem: stop using ->queuedata
nvdimm/btt: stop using ->queuedata
nvdimm/blk: stop using ->queuedata
libnvdimm: Replace guid_copy() with import_guid() where it makes sense
Pull iomap fix from Darrick Wong:
"A single iomap bug fix for a variable type mistake on 32-bit
architectures, fixing an integer overflow problem in the unshare
actor"
* tag 'iomap-5.8-merge-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
iomap: Fix unsharing of an extent >2GB on a 32-bit machine
Pull xfs fix from Darrick Wong:
"We've settled down into the bugfix phase; this one fixes a resource
leak on an error bailout path"
* tag 'xfs-5.8-merge-9' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: Add the missed xfs_perag_put() for xfs_ifree_cluster()
Pull 9p update from Dominique Martinet:
"Another very quiet cycle... Only one commit: increase the size of the
ring used for xen transport"
* tag '9p-for-5.8' of git://github.com/martinetd/linux:
9p/xen: increase XEN_9PFS_RING_ORDER
Pull powerpc fix from Michael Ellerman:
"One fix for a recent change which broke nested KVM guests on Power9.
Thanks to Alexey Kardashevskiy"
* tag 'powerpc-5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Fix nested guest RC bits update
Pull ARM fixes from Russell King:
- fix for "hex" Kconfig default to use 0x0 rather than 0 to allow these
to be removed from defconfigs
- fix from Ard Biesheuvel for EFI HYP mode booting
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8985/1: efi/decompressor: deal with HYP mode boot gracefully
ARM: 8984/1: Kconfig: set default ZBOOT_ROM_TEXT/BSS value to 0x0
