The driver does not discover targets when in loop mode.
The NLP type is correctly getting set when a fabric connection is
detected but, not for loop. The unknown NLP type means that the driver
does not issue a PRLI when in loop topology. Thus target discovery
fails.
Fix by checking the topology during discovery. If it is loop, set the
NLP FC4 type to FCP.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Message "0271 Illegal State Transition: node" seen in logs, all luns are
unuseable for that target.
A window exists in the rcv_plogi path where if the state is plogi issue
but the driver has not issued a plogi, then two reglogins will be sent
for the same RPI. The first one to complete will advance the state to
prli issue the second one will be detected as an illegal state, and
leave the node in an unusable state.
Correct the completion routine for the PLOGI ACC that detects the state
change when the driver starts discovery on the node again and drop the
REGLOGIN mailbox command.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If there are IO's running and host reset or chip reset is triggered,
IO's can fail due to rport time out. During chip reset recovery process,
driver notifies the transport layer that remote port no longer exist, by
calling fc_remote_port_delete(). When this function is called, it
actually delays deletion by "blocking" it. It sets the remote port state
to "FC_PORTSTATE_BLOCKED" and sets FC_RPORT_DEVLOSS_PENDING. When
driver tries to abort the command by calling its abort handler function,
abort handler will wait until remote port state is blocked state or wait
for dev_loss_tmo time. Due to this blocking, rport times out and results
in an IO failure. This patch adds a check for any active reset process
before calling abort handler function.
[mkp: typo]
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If queue count is zero while reading FW dump template, for entry
T263/T274, skip capturing those entries during FW dump capture.
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
ql2xmaxqdepth is the module parameter that seeds the per target
queue depth in the Scsi midlayer (sdev->queue_depth). Performance
testing revealed that increasing this value would improve IOPS
numbers under certain workloads.
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When we tear down the NPIV host configuration in target mode, the
qla_tgt struct was left dangling on the global list. This patch cleans
up link list and frees memory.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
SFP can come in 2 formats: short range/SR and long range/LR. For LR,
user the can increase the number of Buffer to Buffer credits between end
points via Cavium's command line tool. By default, FW uses a lower BB
Credit value optimized for SR. This patch will read the SFP for each
link up event and during chip reset sequence. If the SFP type and
setting are mismatch, then the chip is reset 1 time to use the
appropriate setting.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update ha->wq max_active from 1 to default. MQ interrupts are queued up
via this work queue. This allows interrupts to be process in parrallel,
instead of serialized by the work queue.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If FA-WWPN feature disabled on the switch side and enabled for the
adapter, then driver would update the port name with switch port name.
This patch fixes issue by checking correct BIT flag to validate.
Fixes: 41dc529a46 ("qla2xxx: Improve RSCN handling in driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver will perform following
- Set PFLG_DRIVER_REMOVING flag and do not disable PCIe error reporting
during adapter shutdown.
- If PCIe device count is already zero, return correct error type from
PCI error interface.
- When device is offline, return correct error type from PCIe error
path.
- If there is board disable thread active during shutdown and PCIe
device count is zero then cancel scheduling board disable thread
during shutdown and return.
Signed-off-by: Sawan Chandak <sawan.chandak@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver held spinlocks during callbacks for NVME errors which
resulted in a deadlock because recovery LS cmds needed the same lock.
Signed-off-by: Duane Grigsby <duane.grigsby@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Following error will be logged in to message file while trying to
configure target with multiqueue.
"Cmd 0x1f aborted with timeout since ISP Abort is pending"
"qla25xx_init_queues Rsp que: 1 init failed."
Fixes: 82de802ad4 ("scsi: qla2xxx: Preparation for Target MQ.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Michael Hernandez <michael.hernandez@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
megasas_wait_for_outstanding_fusion checks for pending commands every 1
second. But megasas_complete_cmd_dpc_fusion is only called every 5
seconds. If the commands are already completed by firmware, there is an
additional delay of 5 seconds before driver will process completion for
these commands.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove variable assignments. The value stored in local variable _rc_ is
overwritten at line 2448:rc = lpfc_sli4_bsg_set_link_diag_state(phba,
0); before it can be used.
Addresses-Coverity-ID: 1226935
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Take f_mutex around mmap() processing to protect against races with the
SG_SET_RESERVED_SIZE ioctl. Ensure the reserve buffer length remains
consistent during the mapping operation, and set the "mmap called" flag
to prevent further changes to the reserved buffer size as an atomic
operation with the mapping.
[mkp: fixed whitespace]
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1bc0eb0446 ("scsi: sg: protect accesses to 'reserved' page
array") adds needed concurrency protection for the "reserve" buffer.
Some checks that are initially made outside the lock are replicated once
the lock is taken to ensure the checks and resulting decisions are made
using consistent state.
The check that a request with flag SG_FLAG_MMAP_IO set fits in the
reserve buffer also needs to be performed again under the lock to ensure
the reserve buffer length compared against matches the value in effect
when the request is linked to the reserve buffer. An -ENOMEM should be
returned in this case, instead of switching over to an indirect buffer
as for non-MMAP_IO requests.
Signed-off-by: Todd Poynor <toddpoynor@google.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
